Abstract: This paper presents a computational study of the separated flow in a planer asymmetric diffuser. The steady RANS equations for turbulent incompressible fluid flow and six turbulence closures are used in the present study. The commercial software code, FLUENT 6.3.26, was used for solving the set of governing equations using various turbulence models. Five of the used turbulence models are available directly in the code while the v2-f turbulence model was implemented via User Defined Scalars (UDS) and User Defined Functions (UDF). A series of computational analysis is performed to assess the performance of turbulence models at different grid density. The results show that the standard k-ω, SST k-ω and v2-f models clearly performed better than other models when an adverse pressure gradient was present. The RSM model shows an acceptable agreement with the velocity and turbulent kinetic energy profiles but it failed to predict the location of separation and attachment points. The standard k-ε and the low-Re k- ε delivered very poor results.
Abstract: In this work, axisymetric CFD simulation of fixed bed
GTL reactor has been conducted, using computational fluid dynamics
(CFD). In fixed bed CFD modeling, when N (tube-to-particle
diameter ratio) has a large value, it is common to consider the packed
bed as a porous media. Synthesis gas (a mixture of predominantly
carbon monoxide and hydrogen) was fed to the reactor. The reactor
length was 20 cm, divided to three sections. The porous zone was in
the middle section of the reactor. The model equations were solved
employing finite volume method. The effects of particle diameter,
bed voidage, fluid velocity and bed length on pressure drop have
been investigated. Simulation results showed these parameters could
have remarkable impacts on the reactor pressure drop.
Abstract: The river flow forecasting represents a crucial point to employ for improving a management policy addressed to the right use of water resources as well as for conjugating prevention and defense actions against environmental degradation. The difficulties occurring during the field activities encourage the development and implementation of operative computation and measuring methods addressed to time reduction for data acquisition and processing maintaining a good level of accuracy. Therefore, the aim of the present work is to test a new entropy based expeditive methodology for the evaluation of the rating curves on three gauged sections with different geometric and morphological characteristics. The methodology requires the choice of only three verticals along the measure section and the sampling of only the maximum velocity. The results underline how in most conditions the rating curves drawn can replace those built with classic methodologies, simplifying thus the procedures of data monitoring and calculation.
Abstract: Threedimensional numerical simulations are conducted on a full scale CANDU Moderator and Transient variations of the temperature and velocity distributions inside the tank are determined. The results show that the flow and temperature distributions inside the moderator tank are three dimensional and no symmetry plane can be identified.Competition between the upward moving buoyancy driven flows and the downward moving momentum driven flows, results in the formation of circulation zones. The moderator tank operates in the buoyancy driven mode and any small disturbances in the flow or temperature makes the system unstable and asymmetric. Different types of temperature fluctuations are noted inside the tank: (i) large amplitude are at the boundaries between the hot and cold (ii) low amplitude are in the core of the tank (iii) high frequency fluctuations are in the regions with high velocities and (iv) low frequency fluctuations are in the regions with lower velocities.
Abstract: This research is to study the performance of heat
pump dryer for drying of kaffir lime leaves under different media and
to compare the color values and essential oil content of final products
after drying. In the experiments, kaffir lime leaves were dried in the
closed-loop system at drying temperatures of 40, 50 and 60 oC. The
drying media used in this study were hot air, CO2 and N2 gases. The
velocity of drying media in the drying chamber was 0.4 m/s with
bypass ratio of 30%. The initial moisture content of kaffir lime leaves
was approximately 180-190 % d.b. It was dried until down to a final
moisture content of 10% d.b. From the experiments, the results
showed that drying rate, the coefficient of performance (COP) and
specific energy consumption (SEC) depended on drying temperature.
While drying media did not affect on drying rate. The time for kaffir
lime leaves drying at 40, 50 and 60 oC was 10, 5 and 3 hours,
respectively. The performance of the heat pump system decreased
with drying temperature in the range of 2.20-3.51. In the aspect of
final product color, the greenness and overall color had a great
change under drying temperature at 60 oC rather than drying at 40
and 50 oC. When compared among drying media, the greenness and
overall color of product dried with hot air at 60 oC had a great change
rather than dried with CO2 and N2.
Abstract: The purpose of this study is to derive optimal shapes of
a body located in viscous flows by the finite element method using the
acoustic velocity and the four-step explicit scheme. The formulation
is based on an optimal control theory in which a performance function
of the fluid force is introduced. The performance function should be
minimized satisfying the state equation. This problem can be transformed
into the minimization problem without constraint conditions
by using the adjoint equation with adjoint variables corresponding to
the state equation. The performance function is defined by the drag
and lift forces acting on the body. The weighted gradient method
is applied as a minimization technique, the Galerkin finite element
method is used as a spatial discretization and the four-step explicit
scheme is used as a temporal discretization to solve the state equation
and the adjoint equation. As the interpolation, the orthogonal basis
bubble function for velocity and the linear function for pressure
are employed. In case that the orthogonal basis bubble function is
used, the mass matrix can be diagonalized without any artificial
centralization. The shape optimization is performed by the presented
method.
Abstract: Solution to unsteady Navier-Stokes equation by Splitting method in physical orthogonal algebraic curvilinear coordinate system, also termed 'Non-linear grid system' is presented. The linear terms in Navier-Stokes equation are solved by Crank- Nicholson method while the non-linear term is solved by the second order Adams-Bashforth method. This work is meant to bring together the advantage of Splitting method as pressure-velocity solver of higher efficiency with the advantage of consuming Non-linear grid system which produce more accurate results in relatively equal number of grid points as compared to Cartesian grid. The validation of Splitting method as a solution of Navier-Stokes equation in Nonlinear grid system is done by comparison with the benchmark results for lid driven cavity flow by Ghia and some case studies including Backward Facing Step Flow Problem.
Abstract: This study was aimed for investigating of
manufacturing high aluminum content Mg alloys using a horizontal
twin roll caster. Recently, weight saving has been key issues for lighter
transport equipments as well as electronic component parts. As
alternative materials to aluminum alloys, developing magnesium alloy
with higher strength has been expected. Normally high Aluminum
content Mg alloy has poor ductility and is difficult to be rolled because
of its high strength. However, twin roll casting process is suitable for
manufacturing wrought Mg alloys because materials can be cast
directly from molten metal. In this study, manufacturing of high
aluminum content magnesium alloy sheet using the roll casting
process has been carried out. Effects of manufacturing parameter, such
as roll velocity, pouring temperature and roll gap, on casting was
investigated. A microscopic observation of the crystals of cross section
of as cast strip as well as rolled strip was conducted.
Abstract: A simple microstructure optical fiber design based on an octagonal cladding structure is presented for simultaneously controlling dispersion and leakage properties. The finite difference method with anisotropic perfectly matched boundary layer is used to investigate the guiding properties. It is demonstrated that octagonal photonic crystal fibers with four rings can assume negative ultra-flattened dispersion of -19 + 0.23 ps/nm/km in the wavelength range of 1.275 μm to 1.68 μm, nearly zero ultra-flattened dispersion of 0 ± 0.40 ps/nm/km in a 1.38 to 1.64 μm, and low confinement losses less than 10-3 dB/km in the entire band of interest.
Abstract: A submerged horizontal plate type breakwater is
pointed out as an efficient wave protection device for cage culture in
marine fishery. In order to reveal the wave elimination principle of this
type breakwater, boundary element method is utilized to investigate
this problem. The flow field and the trajectory of water particles are
studied carefully. The flow field analysis shows that: the interaction of
incident wave and adverse current above the plate disturbs the water
domain drastically. This can slow down the horizontal velocity and
vertical velocity of the water particles.
Abstract: The RANS method with Saffman-s turbulence model
was employed to solve the time-dependent turbulent Navier-Stokes
and energy equations for oscillating pipe flows. The method of
partial sums of the Fourier series is used to analyze the harmonic
velocity and temperature results. The complete structures of the
oscillating pipe flows and the averaged Nusselt numbers on the tube
wall are provided by numerical simulation over wide ranges of ReA
and ReR. Present numerical code is validated by comparing the
laminar flow results to analytic solutions and turbulence flow results
to published experimental data at lower and higher Reynolds
numbers respectively. The effects of ReA and ReR on the velocity,
temperature and Nusselt number distributions have been di scussed.
The enhancement of the heat transfer due to oscillating flows has
also been presented. By the way of analyzing the overall Nusselt
number over wide ranges of the Reynolds number Re and Keulegan-
Carpenter number KC, the optimal ratio of the tube diameter over
the oscillation amplitude is obtained based on the existence of a
nearly constant optimal KC number. The potential application of the
present results in sea water cooling has also been discussed.
Abstract: This study investigated the effect of cross sectional
geometry on sediment transport rate. The processes of sediment
transport are generally associated to environmental management,
such as pollution caused by the forming of suspended sediment in the
channel network of a watershed and preserving physical habitats and
native vegetations, and engineering applications, such as the
influence of sediment transport on hydraulic structures and flood
control design. Many equations have been proposed for computing
the sediment transport, the influence of many variables on sediment
transport has been understood; however, the effect of other variables
still requires further research. For open channel flow, sediment
transport capacity is recognized to be a function of friction slope,
flow velocity, grain size, grain roughness and form roughness, the
hydraulic radius of the bed section and the type and quantity of
vegetation cover. The effect of cross sectional geometry of the
channel on sediment transport is one of the variables that need
additional investigation. The width-depth ratio (W/d) is a
comparative indicator of the channel shape. The width is the total
distance across the channel and the depth is the mean depth of the
channel. The mean depth is best calculated as total cross-sectional
area divided by the top width. Channels with high W/d ratios tend to
be shallow and wide, while channels with low (W/d) ratios tend to be
narrow and deep. In this study, the effects of the width-depth ratio on
sediment transport was demonstrated theoretically by inserting the
shape factor in sediment continuity equation and analytically by
utilizing the field data sets for Yalobusha River. It was found by
utilizing the two approaches as a width-depth ratio increases the
sediment transport decreases.
Abstract: This paper describes analysis of low velocity transverse impact on fully backed sandwich beams with composite faces from Eglass/epoxy and cores from Polyurethane or PVC. Indentation on sandwich beams has been analyzed with the existing theories and modeled with the FE code ABAQUS, also loadings have been done experimentally to verify theoretical results. Impact on fully backed has been modeled in two cases of impactor energy with SDOF model (single-degree-of-freedom) and indentation stiffness: lower energy for elastic indentation of sandwich beams and higher energy for plastic area in indentation. Impacts have been modeled by ABAQUS. Impact results can describe response of beam in terms of core and faces thicknesses, core material, indentor energy and energy absorbed. The foam core is modeled using the crushable foam material model and response of the foam core is experimentally characterized in uniaxial compression with higher velocity loading to define quasi impact behaviour.
Abstract: Fuller’s earth is a fine-grained, naturally occurring substance that has a substantial ability to adsorb impurities. In the present study Fuller’s earth has been characterized and used for the removal of Pb(II) from aqueous solution. The effect of various physicochemical parameters such as pH, adsorbent dosage and shaking time on adsorption were studied. The result of the equilibrium studies showed that the solution pH was the key factor affecting the adsorption. The optimum pH for adsorption was 5. Kinetics data for the adsorption of Pb(II) was best described by pseudo-second order model. The effective diffusion co-efficient for Pb(II) adsorption was of the order of 10-8 m2/s. The adsorption data for metal adsorption can be well described by Langmuir adsorption isotherm. The maximum uptake of metal was 103.3 mg/g of adsorbent. Mass transfer analysis was also carried out for the adsorption process. The values of mass transfer coefficients obtained from the study indicate that the velocity of the adsorbate transport from bulk to the solid phase was quite fast. The mean sorption energy calculated from Dubinin-Radushkevich isotherm indicated that the metal adsorption process was chemical in nature.
Abstract: Ion-acoustic solitary and shock waves in dense
quantum plasmas whose constituents are electrons, positrons, and
positive ions are investigated. We assume that ion velocity is weakly
relativistic and also the effects of kinematic viscosity among the
plasma constituents is considered. By using the reductive
perturbation method, the Korteweg–deVries–Burger (KdV-B)
equation is derived.
Abstract: Scaffolds play a key role in tissue engineering and can be produced in many different ways depending on the applications and the materials used. Most researchers used an experimental trialand- error approach into new biomaterials but computer simulation applied to tissue engineering can offer a more exhaustive approach to test and screen out biomaterials. This paper develops the model of scaffolds and Computational Fluid Dynamics that show the value of computer simulations in determining the influence of the geometrical scaffold parameter porosity, pore size and shape on the permeability of scaffolds, magnitude of velocity, drop pressure, shear stress distribution and level and the proper design of the geometry of the scaffold. This creates a need for more advanced studies that include aspects of dynamic conditions of a micro fluid passing through the scaffold were characterized for tissue engineering applications and differentiation of tissues within scaffolds.
Abstract: In this note, a theoretical model for analyzing of
normal penetration of the ogive – nose projectile into metallic targets
is presented .The failure is assumed to be asymmetry petalling and
the analysis is performed by using the energy balance and work done
.The work done consist of the work required for plastic deformation
Wp, the work for transferring the matter to new position Wd and the
work for bending of the petals Wb. In several studies, it has been
shown that we can neglect the loss of energy by temperature.
In this present study, in first, by assuming the crater formation
after perforation, the value of work done is calculated during the
normal penetration of conical projectiles into thin metallic targets.
Then the value of residual velocity and ballistic limit of the projectile
is predicated by using the energy balance. In final, theoretical and
experimental results is compared.
Abstract: A fundamental model consisting of charged particles
moving in free space exposed to alternating and direct current (ACDC)
electromagnetic fields is analyzed. Effects of charged particles
initial position and initial velocity to cyclotron resonance frequency
are observed. Strong effects are observed revealing that effects of
electric and magnetic fields on a charged particle in free space
varies with the initial conditions. This indicates the frequency where
maximum displacement occur can be changed. At this frequency
the amplitude of oscillation of the particle displacement becomes
unbounded.
Abstract: Gliding during night without electric power is an efficient method to enhance endurance performance of solar aircrafts. The properties of maximum gliding endurance path are studied in this paper. The problem is formulated as an optimization problem about maximum endurance can be sustained by certain potential energy storage with dynamic equations and aerodynamic parameter constrains. The optimal gliding path is generated based on gauss pseudo-spectral method. In order to analyse relationship between altitude, velocity of solar UAVs and its endurance performance, the lift coefficient in interval of [0.4, 1.2] and flight envelopes between 0~30km are investigated. Results show that broad range of lift coefficient can improve solar aircrafts- long endurance performance, and it is possible for a solar aircraft to achieve the aim of long endurance during whole night just by potential energy storage.
Abstract: In this paper, the techniques for estimating the
residual stress in high velocity oxy fuel thermal spray coatings have
been discussed and compared. The development trend and the last
investigation have been studied. It is seemed that the there is not
effective study on the effect of the peening action in HVOF
analytically and numerically.