Abstract: A satellite is being integrated and tested by BISEE (Beijing Institute of Spacecraft Environment Engineering). This paper describes the infrared lamp array simulation technology used for satellite thermal balance and thermal vacuum test. These tests were performed in KM6 space environmental simulator in Beijing, China. New software and hardware developed by BISEE, along with enhanced heat flux uniformity, provided for well accomplished thermal balance and thermal vacuum tests. The flux uniformity of lamp array was satisfied with test requirement. Monitored background radiometer offered reliable heat flux measurements with remarkable repeatability. Simulation software supplied accurate thermal flux distribution predictions.
Abstract: The rheological properties, structure and potential synergistic interactions of whey proteins (1-6%) and inulin (20%) in mixed gels in the presence of CaCl2 was the aim of this study. Whey proteins have a strong influence on inulin gel formation. At low concentrations (2%) whey proteins did not impair in inulin gel formation. At higher concentration (4%) whey proteins impaired inulin gelation and inulin impaired the formation of a Ca2+-induced whey protein network. The presence of whey proteins at a level allowing for protein gel network formation (6%) significantly increased the rheological parameters values of the gels. SEM micrographs showed that whey protein structure was coated by inulin moieties which could make the mixed gels firmer. The protein surface hydrophobicity measurements did not exclude synergistic interactions between inulin and whey proteins, however. The use of an electrophoretic technique did not show any stable inulin-whey protein complexes.
Abstract: This paper is mainly concerned with the application of a novel technique of data interpretation to the characterization and classification of measurements of plasma columns in Tokamak reactors for nuclear fusion applications. The proposed method exploits several concepts derived from soft computing theory. In particular, Artifical Neural Networks have been exploited to classify magnetic variables useful to determine shape and position of the plasma with a reduced computational complexity. The proposed technique is used to analyze simulated databases of plasma equilibria based on ITER geometry configuration. As well as demonstrating the successful recovery of scalar equilibrium parameters, we show that the technique can yield practical advantages compares with earlier methods.
Abstract: Distributed Generation (DG) in the form of renewable
power generation systems is currently preferred for clean power
generation. It has a significant impact on the distribution systems.
This impact may be either positively or negatively depending on the
distribution system, distributed generator and load characteristics. In
this works, an overview of DG is briefly introduced. The technology
of DG is also listed while the technical impacts and economic
impacts are explained.
Abstract: The present paper proposes high performance nonlinear
force controllers for a servopneumatic real-time fatigue test
machine. A CompactRIO® controller was used, being fully
programmed using LabVIEW language. Fuzzy logic control
algorithms were evaluated to tune the integral and derivative
components in the development of hybrid controllers, namely a FLC
P and a hybrid FLC PID real-time-based controllers. Their
behaviours were described by using state diagrams. The main
contribution is to ensure a smooth transition between control states,
avoiding discrete transitions in controller outputs. Steady-state errors
lower than 1.5 N were reached, without retuning the controllers.
Good results were also obtained for sinusoidal tracking tasks from
1/¤Ç to 8/¤Ç Hz.
Abstract: The resident registration number was adopted for the purposes of enhanced services for resident convenience and effective performance of governmental administrative affairs. However, it has been used for identification purposes customarily and irrationally in line with the development and spread of the Internet. In response to the growing concern about the leakage of collected RRNs and possible abuses of stolen RRNs, e.g. identity theft, for crimes, the Korean Communications Commission began to take legal/regulatory actions in 2011 to minimize the online collection and use of resident registration numbers. As the use of the RRN was limited after the revision of the Act on Promotion of Information and Communications Network Utilization and Information Protection, etc., online business providers were required to have alternatives to the RRN for the purpose of identifying the user's identity and age, in compliance with the law, and settling disputes with customers. This paper presents means of verifying the personal identity by taking advantage of the commonly used infrastructure and simply replacing personal information entered and stored, without requiring users to enter their RRNs.
Abstract: Actual load, material characteristics and other
quantities often differ from the design values. This can cause worse
function, shorter life or failure of a civil engineering structure, a
machine, vehicle or another appliance. The paper shows main causes
of the uncertainties and deviations and presents a systematic
approach and efficient tools for their elimination or mitigation of
consequences. Emphasis is put on the design stage, which is most
important for reliability ensuring. Principles of robust design and
important tools are explained, including FMEA, sensitivity analysis
and probabilistic simulation methods. The lifetime prediction of
long-life objects can be improved by long-term monitoring of the
load response and damage accumulation in operation. The condition
evaluation of engineering structures, such as bridges, is often based
on visual inspection and verbal description. Here, methods based on
fuzzy logic can reduce the subjective influences.
Abstract: Modern organizations operate under the pressure of
dynamic and often unpredictable changes, both in external and
internal environment. Market success, in this context, requires a
particular competence in the form of flexibility, interpreted here both
on the level of individuals and on the level of organization. This
paper addresses the changes taking place in the sphere of
employment, as observed in economic entities operating on Polish
market. Based on own empirical studies, the authors focus on the
progressing trend of ‘flexibilization’ of employment, particularly in
the context of transformations in organizational structure, designed to
facilitate the transition into management by projects and
differentiation of labor forms.
Abstract: Artificial Neural Network (ANN) has been
extensively used for classification of heart sounds for its
discriminative training ability and easy implementation. However, it
suffers from overparameterization if the number of nodes is not
chosen properly. In such cases, when the dataset has redundancy
within it, ANN is trained along with this redundant information that
results in poor validation. Also a larger network means more
computational expense resulting more hardware and time related
cost. Therefore, an optimum design of neural network is needed
towards real-time detection of pathological patterns, if any from heart
sound signal. The aims of this work are to (i) select a set of input
features that are effective for identification of heart sound signals and
(ii) make certain optimum selection of nodes in the hidden layer for a
more effective ANN structure. Here, we present an optimization
technique that involves Singular Value Decomposition (SVD) and
QR factorization with column pivoting (QRcp) methodology to
optimize empirically chosen over-parameterized ANN structure.
Input nodes present in ANN structure is optimized by SVD followed
by QRcp while only SVD is required to prune undesirable hidden
nodes. The result is presented for classifying 12 common
pathological cases and normal heart sound.
Abstract: A finite element analysis (FEA) computer software HyperWorks is utilized in re-designing an automotive component to reduce its mass. Reduction of components mass contributes towards environmental sustainability by saving world-s valuable metal resources and by reducing carbon emission through improved overall vehicle fuel efficiency. A shape optimization analysis was performed on a rear spindle component. Pre-processing and solving procedures were performed using HyperMesh and RADIOSS respectively. Shape variables were defined using HyperMorph. Then optimization solver OptiStruct was utilized with fatigue life set as a design constraint. Since Stress-Number of Cycle (S-N) theory deals with uni-axial stress, the Signed von Misses stress on the component was used for looking up damage on S-N curve, and Gerber criterion for mean stress corrections. The optimization analysis resulted in mass reduction of 24% of the original mass. The study proved that the adopted approach has high potential use for environmental sustainability.
Abstract: A wireless Ad-hoc network consists of wireless nodes
communicating without the need for a centralized administration, in
which all nodes potentially contribute to the routing process.In this
paper, we report the simulation results of four different scenarios for
wireless ad hoc networks having thirty nodes. The performances of
proposed networks are evaluated in terms of number of hops per
route, delay and throughput with the help of OPNET simulator.
Channel speed 1 Mbps and simulation time 600 sim-seconds were
taken for all scenarios. For the above analysis DSR routing protocols
has been used. The throughput obtained from the above analysis
(four scenario) are compared as shown in Figure 3. The average
media access delay at node_20 for two routes and at node_20 for four
different scenario are compared as shown in Figures 4 and 5. It is
observed that the throughput will degrade when it will follow
different hops for same source to destination (i.e. it has dropped from
1.55 Mbps to 1.43 Mbps which is around 9.7%, and then dropped to
0.48Mbps which is around 35%).
Abstract: In this study, a software has been developed to predict
the optimum conditions for drying of cotton based yarn bobbins in a
hot air dryer. For this purpose, firstly, a suitable drying model has
been specified using experimental drying behavior for different
values of drying parameters. Drying parameters in the experiments
were drying temperature, drying pressure, and volumetric flow rate of
drying air. After obtaining a suitable drying model, additional curve
fittings have been performed to obtain equations for drying time and
energy consumption taking into account the effects of drying
parameters. Then, a software has been developed using Visual Basic
programming language to predict the optimum drying conditions for
drying time and energy consumption.
Abstract: In gas lifted oil fields, the lift gas should be distributed optimally among the wells which share gas from a common source to maximize total oil production. One of the objectives of the paper is to show that a linear MPC consisting of a control objective and an economic objective can be used both as an optimizer and a controller for gas lifted systems. The MPC is based on linearized model of the oil field developed from first principles modeling. Simulation results show that the total oil production is increased by 3.4%. Difficulties in accurately measuring the bottom hole pressure using sensors in harsh operating conditions can be resolved by using an Unscented Kalman Filter (UKF) for estimation. In oil fields where input disturbance (total supply of gas) is not measured, UKF can also be used for disturbance estimation. Increased total oil production due to optimization leads to increased profit.
Abstract: Integration of system process information obtained
through an image processing system with an evolving knowledge
database to improve the accuracy and predictability of wear particle
analysis is the main focus of the paper. The objective is to automate
intelligently the analysis process of wear particle using classification
via self organizing maps. This is achieved using relationship
measurements among corresponding attributes of various
measurements for wear particle. Finally, visualization technique is
proposed that helps the viewer in understanding and utilizing these
relationships that enable accurate diagnostics.
Abstract: Integration of system process information obtained
through an image processing system with an evolving knowledge
database to improve the accuracy and predictability of wear debris
analysis is the main focus of the paper. The objective is to automate
intelligently the analysis process of wear particle using classification
via self-organizing maps. This is achieved using relationship
measurements among corresponding attributes of various
measurements for wear debris. Finally, visualization technique is
proposed that helps the viewer in understanding and utilizing these
relationships that enable accurate diagnostics.
Abstract: Glaucoma diagnosis involves extracting three features
of the fundus image; optic cup, optic disc and vernacular. Present
manual diagnosis is expensive, tedious and time consuming. A
number of researches have been conducted to automate this process.
However, the variability between the diagnostic capability of an
automated system and ophthalmologist has yet to be established. This
paper discusses the efficiency and variability between
ophthalmologist opinion and digital technique; threshold. The
efficiency and variability measures are based on image quality
grading; poor, satisfactory or good. The images are separated into
four channels; gray, red, green and blue. A scientific investigation
was conducted on three ophthalmologists who graded the images
based on the image quality. The images are threshold using multithresholding
and graded as done by the ophthalmologist. A
comparison of grade from the ophthalmologist and threshold is made.
The results show there is a small variability between result of
ophthalmologists and digital threshold.
Abstract: In this paper, we propose a chaotic cipher system consisting of Improved Volterra Filters and the mapping that is created from the actual voice by using Radial Basis Function Network. In order to achieve a practical system, the system supposes to use the digital communication line, such as the Internet, to maintain the parameter matching between the transmitter and receiver sides. Therefore, in order to withstand the attack from outside, it is necessary that complicate the internal state and improve the sensitivity coefficient. In this paper, we validate the robustness of proposed method from three perspectives of "Chaotic properties", "Randomness", "Coefficient sensitivity".
Abstract: This paper introduced the status quo of laws and
regulations of sustainable construction in China and investigated the
existing problems of current laws and regulations through
person-interviews in Beijing, Shanghai, Chongqing and Shenzhen in
China. The problems include incomplete legal system, lack of
guidance of higher-level laws, backward in some laws and regulations,
unclear legal liability and poor law enforcement. Aimed at these
problems, this paper also put forward some improvement approaches,
such as filling the legal gap, revising laws and regulations, establishing
incentive system and keeping pace with level of development.
Abstract: For the last decade, statistics show traumatic brain
injury (TBI) is a growing concern in our legal system. In an effort to
obtain data regarding the influence of neuropsychological expert
witness testimony in a criminal case, this study tested three
hypotheses. H1: The majority of jurors will vote not guilty, due to
mild head injury. H2: The jurors will give more credence to the
testimony of the neuropsychologist rather than the psychiatrist. H3:
The jurors will be more lenient in their sentencing, given the
testimony of the neuropsychologist-s testimony. The criterion for
inclusion in the study as a participant is identical to those used for
inclusion in the eligibility for jury duty in the United States. A chisquared
test was performed to analyze the data for the three
hypotheses. The results supported all of the hypotheses; however
statistical significance was seen in H1 and H2 only.
Abstract: In this paper, a modified CCCII is presented. We have used a current mirror with low supply voltage. This circuit is operated at low supply voltage of ±1V. Tspice simulations for TSMC 0.18μm CMOS Technology has shown that the current and voltage bandwidth are respectively 3.34GHz and 4.37GHz, and parasitic resistance at port X has a value of 169.320 for a control current of 120μA. In order to realize this circuit, we have implemented in this first step a universal current mode filter where the frequency can reach the 134.58MHz. In the second step, we have implemented two simulated inductors: one floating and the other grounded. These two inductors are operated in high frequency and variable depending on bias current I0. Finally, we have used the two last inductors respectively to implement two sinusoidal oscillators domains of frequencies respectively: [470MHz, 692MHz], and [358MHz, 572MHz] for bias currents I0 [80μA, 350μA].