Abstract: This paper presents a method of economic factorial analysis of the CO2 emissions based on the extension of the Divisia index to interconnected factors. This approach, contrary to the Kaya identity, considers three main factors of the CO2 emissions: gross domestic product, energy consumption, and population - as equally important, and allows for accounting of all of them simultaneously. The three factors are included into analysis together with their carbon intensities that allows for obtaining a comprehensive picture of the change in the CO2 emissions. A computer program in R-language that is available for free download serves automation of the calculations. A case study of the U.S. carbon dioxide emissions is used as an example.
Abstract: There are various sources of energies available
worldwide and among them, crude oil plays a vital role. Oil recovery
is achieved using conventional primary and secondary recovery
methods. In-order to recover the remaining residual oil, technologies
like Enhanced Oil Recovery (EOR) are utilized which is also known
as tertiary recovery. Among EOR, Microbial enhanced oil recovery
(MEOR) is a technique which enables the improvement of oil
recovery by injection of bio-surfactant produced by microorganisms.
Bio-surfactant can retrieve unrecoverable oil from the cap rock which
is held by high capillary force. Bio-surfactant is a surface active agent
which can reduce the interfacial tension and reduce viscosity of oil
and thereby oil can be recovered to the surface as the mobility of the
oil is increased. Research in this area has shown promising results
besides the method is echo-friendly and cost effective compared with
other EOR techniques. In our research, on laboratory scale we
produced bio-surfactant using the strain Pseudomonas putida (MTCC
2467) and injected into designed simple sand packed column which
resembles actual petroleum reservoir. The experiment was conducted
in order to determine the efficiency of produced bio-surfactant in oil
recovery. The column was made of plastic material with 10 cm in
length. The diameter was 2.5 cm. The column was packed with fine
sand material. Sand was saturated with brine initially followed by oil
saturation. Water flooding followed by bio-surfactant injection was
done to determine the amount of oil recovered. Further, the injection
of bio-surfactant volume was varied and checked how effectively oil
recovery can be achieved. A comparative study was also done by
injecting Triton X 100 which is one of the chemical surfactant. Since,
bio-surfactant reduced surface and interfacial tension oil can be easily
recovered from the porous sand packed column.
Abstract: The author proposes an extension of particle swarm optimization (PSO) for solving interval-valued optimization problems and applies the extended PSO to evolutionary training of neural networks (NNs) with interval weights. In the proposed PSO, values in the genotypes are not real numbers but intervals. Experimental results show that interval-valued NNs trained by the proposed method could well approximate hidden target functions despite the fact that no training data was explicitly provided.
Abstract: The author previously proposed an extension of differential evolution. The proposed method extends the processes of DE to handle interval numbers as genotype values so that DE can be applied to interval-valued optimization problems. The interval DE can employ either of two interval models, the lower and upper model or the center and width model, for specifying genotype values. Ability of the interval DE in searching for solutions may depend on the model. In this paper, the author compares the two models to investigate which model contributes better for the interval DE to find better solutions. Application of the interval DE is evolutionary training of interval-valued neural networks. A result of preliminary study indicates that the CW model is better than the LU model: the interval DE with the CW model could evolve better neural networks.
Abstract: In this study, a new reliable technique use to handle the foam drainage equation. This new method is resulted from VIM by a simple modification that is Reconstruction of Variational Iteration Method (RVIM). The drainage of liquid foams involves the interplay of gravity, surface tension, and viscous forces. Foaming occurs in many distillation and absorption processes. Results are compared with those of Adomian’s decomposition method (ADM).The comparisons show that the Reconstruction of Variational Iteration Method is very effective and overcome the difficulty of traditional methods and quite accurate to systems of non-linear partial differential equations.
Abstract: Discrete search path planning in time-constrained uncertain environment relying upon imperfect sensors is known to be hard, and current problem-solving techniques proposed so far to compute near real-time efficient path plans are mainly bounded to provide a few move solutions. A new information-theoretic –based open-loop decision model explicitly incorporating false alarm sensor readings, to solve a single agent military logistics search-and-delivery path planning problem with anticipated feedback is presented. The decision model consists in minimizing expected entropy considering anticipated possible observation outcomes over a given time horizon. The model captures uncertainty associated with observation events for all possible scenarios. Entropy represents a measure of uncertainty about the searched target location. Feedback information resulting from possible sensor observations outcomes along the projected path plan is exploited to update anticipated unit target occupancy beliefs. For the first time, a compact belief update formulation is generalized to explicitly include false positive observation events that may occur during plan execution. A novel genetic algorithm is then proposed to efficiently solve search path planning, providing near-optimal solutions for practical realistic problem instances. Given the run-time performance of the algorithm, natural extension to a closed-loop environment to progressively integrate real visit outcomes on a rolling time horizon can be easily envisioned. Computational results show the value of the approach in comparison to alternate heuristics.
Abstract: Taiwan was the first country in Asia to announce
“Nuclear-Free Homeland" in 2002. In 2008, the new government
released the Sustainable Energy Policy Guidelines to lower the
nationwide CO2 emissions some time between 2016 and 2020 back to
the level of year 2008, further abatement of CO2 emissions is planed in
year 2025 when CO2 emissions will decrease to the level of year 2000.
Besides, under consideration of the issues of energy, environment and
economics (3E), the new government declared that the nuclear power
is a carbon-less energy option. This study analyses the effects of
nuclear power generation for CO2 abatement scenarios in Taiwan. The
MARKAL-MACRO energy model was adopted to evaluate economic
impacts and energy deployment due to life extension of existing
nuclear power plants and build new nuclear power units in CO2
abatement scenarios. The results show that CO2 abatement effort is
expensive. On the other hand, nuclear power is a cost-effective choice.
The GDP loss rate in the case of building new nuclear power plants is
around two thirds of the Nuclear-Free Homeland case. Nuclear power
generation has the capacity to provide large-scale CO2 free electricity.
Therefore, the results show that nuclear power is not only an option for
Taiwan, but also a requisite for Taiwan-s CO2 reduction strategy.
Abstract: Utilizing echoic intension and distribution from different organs and local details of human body, ultrasonic image can catch important medical pathological changes, which unfortunately may be affected by ultrasonic speckle noise. A feature preserving ultrasonic image denoising and edge enhancement scheme is put forth, which includes two terms: anisotropic diffusion and edge enhancement, controlled by the optimum smoothing time. In this scheme, the anisotropic diffusion is governed by the local coordinate transformation and the first and the second order normal derivatives of the image, while the edge enhancement is done by the hyperbolic tangent function. Experiments on real ultrasonic images indicate effective preservation of edges, local details and ultrasonic echoic bright strips on denoising by our scheme.
Abstract: Ontologies play an important role in semantic web
applications and are often developed by different groups and
continues to evolve over time. The knowledge in ontologies changes
very rapidly that make the applications outdated if they continue to
use old versions or unstable if they jump to new versions. Temporal
frames using frame versioning and slot versioning are used to take
care of dynamic nature of the ontologies. The paper proposes new
tags and restructured OWL format enabling the applications to work
with the old or new version of ontologies. Gene Ontology, a very
dynamic ontology, has been used as a case study to explain the OWL
Ontology with Temporal Tags.
Abstract: To enhance installation security, a LNG storage in Rudong of Jiangsu province was adopted as a practical work, and it was analyzed by nonlinear finite element method to research overall and local stability performance, as well as the stress and deformation under the action of wind load and self-weight. Results indicate that deformation is tiny when steel mesh maintains as an overall ring, and stress caused by vertical bending moment and tension of bottom tie wire are also in the safe range. However, axial forces of lap reinforcement in adjacent steel mesh exceed the ultimate bearing capacity of tie wire. Hence, tie wires are ruptured; single mesh loses lateral connection and turns into monolithic status as the destruction of overall structure. Further more, monolithic steel mesh is led to collapse by the damage of bottom connection. So, in order to prevent connection failure and enhance installation security, the overlapping parts of steel mesh should be taken more reliable measures.
Abstract: The presence of a vertical edge-crack within a web
plate subjected to pure bending induces local compressive stresses
about the crack which may cause tension buckling. Approximate
theoretical expressions were derived for the critical far-field tensile
stress and bending moment capacity of an edge-cracked web plate
associated with tension buckling. These expressions were validated
with finite element analyses and used to investigate the possibility of
tension buckling in web-cracked trial girders. It was found that
tension buckling is an unlikely occurrence unless the web is relatively
thin or the crack is very long.
Abstract: In the present study, computational fluid dynamics
(CFD) simulation has been executed to investigate the transition
boundaries of different flow patterns for moderately viscous oil-water
(viscosity ratio 107, density ratio 0.89 and interfacial tension of 0.032
N/m.) two-phase flow through a horizontal pipeline with internal
diameter and length of 0.025 m and 7.16 m respectively. Volume of
Fluid (VOF) approach including effect of surface tension has been
employed to predict the flow pattern. Geometry and meshing of the
present problem has been drawn using GAMBIT and ANSYS
FLUENT has been used for simulation. A total of 47037 quadrilateral
elements are chosen for the geometry of horizontal pipeline. The
computation has been performed by assuming unsteady flow,
immiscible liquid pair, constant liquid properties, co-axial flow and a
T-junction as entry section. The simulation correctly predicts the
transition boundaries of wavy stratified to stratified mixed flow.
Other transition boundaries are yet to be simulated. Simulated data
has been validated with our own experimental results.
Abstract: The migration of a deformable drop in simple shear
flow at finite Reynolds numbers is investigated numerically by
solving the full Navier-Stokes equations using a finite
difference/front tracking method. The objectives of this study are to
examine the effectiveness of the present approach to predict the
migration of a drop in a shear flow and to investigate the behavior of
the drop migration with different drop sizes and non-unity viscosity
ratios. It is shown that the drop deformation depends strongly on the
capillary number, so that; the proper non-dimensional number for the
interfacial tension is the capillary number. The rate of migration
increased with increasing the drop radius. In other words, the
required time for drop migration to the centreline decreases. As the
viscosity ratio increases, the drop rotates more slowly and the
lubrication force becomes stronger. The increased lubrication force
makes it easier for the drop to migrate to the centre of the channel.
The migration velocity of the drop vanishes as the drop reaches the
centreline under viscosity ratio of one and non-unity viscosity ratios.
To validate the present calculations, some typical results are
compared with available experimental and theoretical data.
Abstract: The basic aim of our study is to give a possible model for handling uncertain information. This model is worked out in the framework of DATALOG. The concept of multivalued knowledgebase will be defined as a quadruple of any background knowledge; a deduction mechanism; a connecting algorithm, and a function set of the program, which help us to determine the uncertainty levels of the results. At first the concept of fuzzy Datalog will be summarized, then its extensions for intuitionistic- and interval-valued fuzzy logic is given and the concept of bipolar fuzzy Datalog is introduced. Based on these extensions the concept of multivalued knowledge-base will be defined. This knowledge-base can be a possible background of a future agent-model.
Abstract: Current advancements in nanotechnology are dependent
on the capabilities that can enable nano-scientists to extend their eyes
and hands into the nano-world. For this purpose, a haptics (devices
capable of recreating tactile or force sensations) based system for
AFM (Atomic Force Microscope) is proposed. The system enables
the nano-scientists to touch and feel the sample surfaces, viewed
through AFM, in order to provide them with better understanding of
the physical properties of the surface, such as roughness, stiffness and
shape of molecular architecture. At this stage, the proposed work uses
of ine images produced using AFM and perform image analysis to
create virtual surfaces suitable for haptics force analysis. The research
work is in the process of extension from of ine to online process
where interaction will be done directly on the material surface for
realistic analysis.
Abstract: FAQ system can make user find answer to the problem that puzzles them. But now the research on Chinese FAQ system is still on the theoretical stage. This paper presents an approach to semantic inference for FAQ mining. To enhance the efficiency, a small pool of the candidate question-answering pairs retrieved from the system for the follow-up work according to the concept of the agriculture domain extracted from user input .Input queries or questions are converted into four parts, the question word segment (QWS), the verb segment (VS), the concept of agricultural areas segment (CS), the auxiliary segment (AS). A semantic matching method is presented to estimate the similarity between the semantic segments of the query and the questions in the pool of the candidate. A thesaurus constructed from the HowNet, a Chinese knowledge base, is adopted for word similarity measure in the matcher. The questions are classified into eleven intension categories using predefined question stemming keywords. For FAQ mining, given a query, the question part and answer part in an FAQ question-answer pair is matched with the input query, respectively. Finally, the probabilities estimated from these two parts are integrated and used to choose the most likely answer for the input query. These approaches are experimented on an agriculture FAQ system. Experimental results indicate that the proposed approach outperformed the FAQ-Finder system in agriculture FAQ retrieval.
Abstract: This paper deals with infinite time horizon fuzzy Economic Order Quantity (EOQ) models for deteriorating items with
stock dependent demand rate and nonlinear holding costs by taking deterioration rate θ0 as a triangular fuzzy number (θ0 −δ 1, θ0, θ0 +δ 2), where 1 2 0 0
Abstract: Using the idea of prime and semiprime bi-ideals of
rings, the concept of prime and semiprime generalized bi-ideals of
rings is introduced, which is an extension of the concept of prime and
semiprime bi-ideals of rings and some interesting characterizations
of prime and semiprime generalized bi-ideals are obtained. Also,
we give the relationship between the Baer radical and prime and
semiprime generalized bi-ideals of rings in the same way as of biideals
of rings which was studied by Roux.
Abstract: The Time-Domain Boundary Element Method (TDBEM)
is a well known numerical technique that handles quite
properly dynamic analyses considering infinite dimension media.
However, when these analyses are also related to nonlinear behavior,
very complex numerical procedures arise considering the TD-BEM,
which may turn its application prohibitive. In order to avoid this
drawback and model nonlinear infinite media, the present work
couples two BEM formulations, aiming to achieve the best of two
worlds. In this context, the regions expected to behave nonlinearly
are discretized by the Domain Boundary Element Method (D-BEM),
which has a simpler mathematical formulation but is unable to deal
with infinite domain analyses; the TD-BEM is employed as in the
sense of an effective non-reflexive boundary. An iterative procedure
is considered for the coupling of the TD-BEM and D-BEM, which is
based on a relaxed renew of the variables at the common interfaces.
Elastoplastic models are focused and different time-steps are allowed
to be considered by each BEM formulation in the coupled analysis.
Abstract: The Romanian government has been making
significant attempts to make its services and information available on
the Internet. According to the UN e-government survey conducted in
2008, Romania comes under mid range countries by utilization of egovernment
(percent of utilization 41%). Romania-s national portal
www.e-guvernare.ro aims at progressively making all services and
information accessible through the portal. However, the success of
these efforts depends, to a great extent, on how well the targeted
users for such services, citizens in general, make use of them. For
this reason, the purpose of the presented study was to identify what
factors could affect the citizens' adoption of e-government services.
The study is an extension of the Technology Acceptance Model. The
proposed model was validated using data collected from 481 citizens.
The results provided substantial support for all proposed hypotheses
and showed the significance of the extended constructs.