Abstract: Compression algorithms reduce the redundancy in
data representation to decrease the storage required for that data.
Lossless compression researchers have developed highly
sophisticated approaches, such as Huffman encoding, arithmetic
encoding, the Lempel-Ziv (LZ) family, Dynamic Markov
Compression (DMC), Prediction by Partial Matching (PPM), and
Burrows-Wheeler Transform (BWT) based algorithms.
Decompression is also required to retrieve the original data by
lossless means. A compression scheme for text files coupled with
the principle of dynamic decompression, which decompresses only
the section of the compressed text file required by the user instead of
decompressing the entire text file. Dynamic decompressed files offer
better disk space utilization due to higher compression ratios
compared to most of the currently available text file formats.
Abstract: This paper proposes a Fuzzy Expert System design to
determine the wearing properties of nitrided and non nitrided steel.
The proposed Fuzzy Expert System approach helps the user and the
manufacturer to forecast the wearing properties of nitrided and non
nitrided steel under specified laboratory conditions. Surfaces of the
engineering components are often nitrided for improving wear,
corosion, fatigue specifications. A major property of nitriding
process is reducing distortion and wearing of the metalic alloys. A
Fuzzy Expert System was developed for determining the wearing and
durability properties of nitrided and non nitrided steels that were
tested under different loads and different sliding speeds in the
laboratory conditions.
Abstract: This paper suggests a new Affine Projection (AP) algorithm with variable data-reuse factor using the condition number as a decision factor. To reduce computational burden, we adopt a recently reported technique which estimates the condition number of an input data matrix. Several simulations show that the new algorithm has better performance than that of the conventional AP algorithm.
Abstract: Nowadays there is a growing interest in biofuel production in most countries because of the increasing concerns about hydrocarbon fuel shortage and global climate changes, also for enhancing agricultural economy and producing local needs for transportation fuel. Ethanol can be produced from biomass by the hydrolysis and sugar fermentation processes. In this study ethanol was produced without using expensive commercial enzymes from sugarcane bagasse. Alkali pretreatment was used to prepare biomass before enzymatic hydrolysis. The comparison between NaOH, KOH and Ca(OH)2 shows NaOH is more effective on bagasse. The required enzymes for biomass hydrolysis were produced from sugarcane solid state fermentation via two fungi: Trichoderma longibrachiatum and Aspergillus niger. The results show that the produced enzyme solution via A. niger has functioned better than T. longibrachiatum. Ethanol was produced by simultaneous saccharification and fermentation (SSF) with crude enzyme solution from T. longibrachiatum and Saccharomyces cerevisiae yeast. To evaluate this procedure, SSF of pretreated bagasse was also done using Celluclast 1.5L by Novozymes. The yield of ethanol production by commercial enzyme and produced enzyme solution via T. longibrachiatum was 81% and 50% respectively.
Abstract: Packet switched data network like Internet, which has
traditionally supported throughput sensitive applications such as email
and file transfer, is increasingly supporting delay-sensitive
multimedia applications such as interactive video. These delaysensitive
applications would often rather sacrifice some throughput
for better delay. Unfortunately, the current packet switched network
does not offer choices, but instead provides monolithic best-effort
service to all applications. This paper evaluates Class Based Queuing
(CBQ), Coordinated Earliest Deadline First (CEDF), Weighted
Switch Deficit Round Robin (WSDRR) and RED-Boston scheduling
schemes that is sensitive to delay bound expectations for variety of
real time applications and an enhancement of WSDRR is proposed.
Abstract: In this paper, we analyze the rotor eddy currents losses provoqued by the stator slot harmonics developed in the permanent magnets or pole pieces of synchronous machines. An analytical approach is presented to evaluate the effect of slot ripples on rotor field and losses calculation. This analysis is then tested on a model by 2D/3D finite element (FE) calculation. The results show a good agreement on loss calculations when skin effect is negligible and the magnet is considered.
Abstract: A new approach to promote the generalization ability
of neural networks is presented. It is based on the point of view of
fuzzy theory. This approach is implemented through shrinking or
magnifying the input vector, thereby reducing the difference between
training set and testing set. It is called “shrinking-magnifying
approach" (SMA). At the same time, a new algorithm; α-algorithm is
presented to find out the appropriate shrinking-magnifying-factor
(SMF) α and obtain better generalization ability of neural networks.
Quite a few simulation experiments serve to study the effect of SMA
and α-algorithm. The experiment results are discussed in detail, and
the function principle of SMA is analyzed in theory. The results of
experiments and analyses show that the new approach is not only
simpler and easier, but also is very effective to many neural networks
and many classification problems. In our experiments, the proportions
promoting the generalization ability of neural networks have even
reached 90%.
Abstract: This paper proposes a bi-objective model for the
facility location problem under a congestion system. The idea of the
model is motivated by applications of locating servers in bank
automated teller machines (ATMS), communication networks, and so
on. This model can be specifically considered for situations in which
fixed service facilities are congested by stochastic demand within
queueing framework. We formulate this model with two perspectives
simultaneously: (i) customers and (ii) service provider. The
objectives of the model are to minimize (i) the total expected
travelling and waiting time and (ii) the average facility idle-time.
This model represents a mixed-integer nonlinear programming
problem which belongs to the class of NP-hard problems. In addition,
to solve the model, two metaheuristic algorithms including nondominated
sorting genetic algorithms (NSGA-II) and non-dominated
ranking genetic algorithms (NRGA) are proposed. Besides, to
evaluate the performance of the two algorithms some numerical
examples are produced and analyzed with some metrics to determine
which algorithm works better.
Abstract: In industry, on of the most important subjects is die
and it's characteristics in which for cutting and forming different
mechanical pieces, various punch and matrix metal die are used.
whereas the common parts which form the main frame die are not
often proportion with pieces and dies therefore using a part as socalled
common part for frames in specified dimension ranges can
decrease the time of designing, occupied space of warehouse and
manufacturing costs. Parts in dies with getting uniform in their shape
and dimension make common parts of dies. Common parts of punch
and matrix metal die are as bolster, guide bush, guide pillar and
shank. In this paper the common parts and effective parameters in
selecting each of them as the primary information are studied,
afterward for selection and design of mechanical parts an
introduction and investigation based on the Mech. Desk. software is
done hence with developing this software can standardize the metal
common parts of punch and matrix. These studies will be so useful
for designer in their designing and also using it has with very much
advantage for manufactures of products in decreasing occupied
spaces by dies.
Abstract: The conventional GA combined with a local search
algorithm, such as the 2-OPT, forms a hybrid genetic algorithm(HGA)
for the traveling salesman problem (TSP). However, the geometric
properties which are problem specific knowledge can be used to
improve the search process of the HGA. Some tour segments (edges)
of TSPs are fine while some maybe too long to appear in a short tour.
This knowledge could constrain GAs to work out with fine tour
segments without considering long tour segments as often.
Consequently, a new algorithm is proposed, called intelligent-OPT
hybrid genetic algorithm (IOHGA), to improve the GA and the 2-OPT
algorithm in order to reduce the search time for the optimal solution.
Based on the geometric properties, all the tour segments are assigned
2-level priorities to distinguish between good and bad genes. A
simulation study was conducted to evaluate the performance of the
IOHGA. The experimental results indicate that in general the IOHGA
could obtain near-optimal solutions with less time and better accuracy
than the hybrid genetic algorithm with simulated annealing algorithm
(HGA(SA)).
Abstract: Minimum Quantity Lubrication (MQL) technique
obtained a significant attention in machining processes to reduce
environmental loads caused by usage of conventional cutting fluids.
Recently nanofluids are finding an extensive application in the field
of mechanical engineering because of their superior lubrication and
heat dissipation characteristics. This paper investigates the use of a
nanofluid under MQL mode to improve grinding characteristics of
Ti-6Al-4V alloy. Taguchi-s experimental design technique has been
used in the present investigation and a second order model has been
established to predict grinding forces and surface roughness.
Different concentrations of water based Al2O3 nanofluids were
applied in the grinding operation through MQL setup developed in
house and the results have been compared with those of conventional
coolant and pure water. Experimental results showed that grinding
forces reduced significantly when nano cutting fluid was used even at
low concentration of the nano particles and surface finish has been
found to improve with higher concentration of the nano particles.
Abstract: The paper presents a one-dimensional transient
mathematical model of compressible non-isothermal multicomponent
fluid mixture flow in a pipe. The set of the mass,
momentum and enthalpy conservation equations for gas phase is
solved in the model. Thermo-physical properties of multi-component
gas mixture are calculated by solving the Equation of State (EOS)
model. The Soave-Redlich-Kwong (SRK-EOS) model is chosen. Gas
mixture viscosity is calculated on the basis of the Lee-Gonzales-
Eakin (LGE) correlation. Numerical analysis of rapid gas
decompression process in rich and base natural gases is made on the
basis of the proposed mathematical model. The model is successfully
validated on the experimental data [1]. The proposed mathematical
model shows a very good agreement with the experimental data [1] in
a wide range of pressure values and predicts the decompression in
rich and base gas mixtures much better than analytical and
mathematical models, which are available from the open source
literature.
Abstract: The protection issues in distribution systems with open and closed-loop are studied, and a generalized protection setting scheme based on the traditional over current protection theories is proposed to meet the new requirements. The setting method is expected to be easier realized using computer program, so that the on-line adaptive setting for coordination in distribution system can be implemented. An automatic setting program is created and several cases are taken into practice. The setting results are verified by the coordination curves of the protective devices which are plotted using MATLAB.
Abstract: The paper discusses the results obtained to predict
reinforcement in singly reinforced beam using Neural Net (NN),
Support Vector Machines (SVM-s) and Tree Based Models. Major
advantage of SVM-s over NN is of minimizing a bound on the
generalization error of model rather than minimizing a bound on
mean square error over the data set as done in NN. Tree Based
approach divides the problem into a small number of sub problems to
reach at a conclusion. Number of data was created for different
parameters of beam to calculate the reinforcement using limit state
method for creation of models and validation. The results from this
study suggest a remarkably good performance of tree based and
SVM-s models. Further, this study found that these two techniques
work well and even better than Neural Network methods. A
comparison of predicted values with actual values suggests a very
good correlation coefficient with all four techniques.
Abstract: In this paper, a design methodology to implement low-power and high-speed 2nd order recursive digital Infinite Impulse Response (IIR) filter has been proposed. Since IIR filters suffer from a large number of constant multiplications, the proposed method replaces the constant multiplications by using addition/subtraction and shift operations. The proposed new 6T adder cell is used as the Carry-Save Adder (CSA) to implement addition/subtraction operations in the design of recursive section IIR filter to reduce the propagation delay. Furthermore, high-level algorithms designed for the optimization of the number of CSA blocks are used to reduce the complexity of the IIR filter. The DSCH3 tool is used to generate the schematic of the proposed 6T CSA based shift-adds architecture design and it is analyzed by using Microwind CAD tool to synthesize low-complexity and high-speed IIR filters. The proposed design outperforms in terms of power, propagation delay, area and throughput when compared with MUX-12T, MCIT-7T based CSA adder filter design. It is observed from the experimental results that the proposed 6T based design method can find better IIR filter designs in terms of power and delay than those obtained by using efficient general multipliers.
Abstract: A 1.2 V, 0.61 mA bias current, low noise amplifier
(LNA) suitable for low-power applications in the 2.4 GHz band is
presented. Circuit has been implemented, laid out and simulated using
a UMC 130 nm RF-CMOS process. The amplifier provides a 13.3 dB
power gain a noise figure NF< 2.28 dB and a 1-dB compression point
of -15.69 dBm, while dissipating 0.74 mW. Such performance make
this design suitable for wireless sensor networks applications such as
ZigBee.
Abstract: The main objectives of this paper are to measure
pollutants concentrations in the oil refinery area in Kuwait over three
periods during one year, obtain recent emission inventory for the
three refineries of Kuwait, use AERMOD and the emission inventory
to predict pollutants concentrations and distribution, compare model
predictions against measured data, and perform numerical
experiments to determine conditions at which emission rates and the
resulting pollutant dispersion is below maximum allowable limits.
Abstract: Optical Coherence Tomography (OCT) combined
with the Confocal Microscopy, as a noninvasive method, permits the
determinations of materials defects in the ceramic layers depth. For
this study 256 anterior and posterior metal and integral ceramic fixed
partial dentures were used, made with Empress (Ivoclar), Wollceram
and CAD/CAM (Wieland) technology. For each investigate area 350
slices were obtain and a 3D reconstruction was perform from each
stuck. The Optical Coherent Tomography, as a noninvasive method,
can be used as a control technique in integral ceramic technology,
before placing those fixed partial dentures in the oral cavity. The
purpose of this study is to evaluate the capability of En face Optical
Coherence Tomography (OCT) combined with a fluorescent method
in detection and analysis of possible material defects in metalceramic
and integral ceramic fixed partial dentures. As a conclusion,
it is important to have a non invasive method to investigate fixed
partial prostheses before their insertion in the oral cavity in order to
satisfy the high stress requirements and the esthetic function.
Abstract: Motivated by Microsoft Co. Academic Program
initiative, the department of Information Technology in King Saud
University has adopted Microsoft products in three courses. The
initiative aimed at enhancing the abilities of the university graduates
and equipping them with skills that would help them in the job
market. A number of methods of collecting assessment data were
used to evaluate the course adoption initiative. Assessment data
indicated that the goal of the course adoption is being achieved and
that the students were much better prepared to design applications
and administrate networks.
Abstract: SAD (Sum of Absolute Difference) algorithm is
heavily used in motion estimation which is computationally highly
demanding process in motion picture encoding. To enhance the
performance of motion picture encoding on a VLIW processor, an
efficient implementation of SAD algorithm on the VLIW processor is
essential. SAD algorithm is programmed as a nested loop with a
conditional branch. In VLIW processors, loop is usually optimized by
software pipelining, but researches on optimal scheduling of software
pipelining for nested loops, especially nested loops with conditional
branches are rare. In this paper, we propose an optimal scheduling and
implementation of SAD algorithm with conditional branch on a VLIW
DSP processor. The proposed optimal scheduling first transforms the
nested loop with conditional branch into a single loop with conditional
branch with consideration of full utilization of ILP capability of the
VLIW processor and realization of earlier escape from the loop. Next,
the proposed optimal scheduling applies a modulo scheduling
technique developed for single loop. Based on this optimal scheduling
strategy, optimal implementation of SAD algorithm on TMS320C67x,
a VLIW DSP is presented. Through experiments on TMS320C6713
DSK, it is shown that H.263 encoder with the proposed SAD
implementation performs better than other H.263 encoder with other
SAD implementations, and that the code size of the optimal SAD
implementation is small enough to be appropriate for embedded
environments.