Abstract: A Positron Emission Tomography (PET) is a radioisotope imaging technique that illustrates the organs and the metabolisms of the human body. This technique is based on the simultaneous detection of 511 keV annihilation photons, annihilated as a result of electrons annihilating positrons that radiate from positron-emitting radioisotopes that enter biological active molecules in the body. This study was conducted on ten patients in an effort to conduct patient-related experimental studies. Dosage monitoring for the bladder, which was the organ that received the highest dose during PET applications, was conducted for 24 hours. Assessment based on measuring urination activities after injecting patients was also a part of this study. The MIRD method was used to conduct dosage calculations for results obtained from experimental studies. Results obtained experimentally and theoretically were assessed comparatively.
Abstract: The remediation of water resources pollution in
developing countries requires the application of alternative
sustainable cheaper and efficient end-of-pipe wastewater treatment
technologies. The feasibility of use of South African cheap and
abundant pine tree (Pinus patula) sawdust for development of lowcost
AC of comparable quality to expensive commercial ACs in the
abatement of water pollution was investigated. AC was developed at
optimized two-stage N2-superheated steam activation conditions in a
fixed bed reactor, and characterized for proximate and ultimate
properties, N2-BET surface area, pore size distribution, SEM, pHPZC
and FTIR. The sawdust pyrolysis activation energy was evaluated by
TGA. Results indicated that the chars prepared at 800oC and 2hrs
were suitable for development of better quality AC at 800oC and 47%
burn-off having BET surface area (1086m2/g), micropore volume
(0.26cm3/g), and mesopore volume (0.43cm3/g) comparable to
expensive commercial ACs, and suitable for water contaminants
removal. The developed AC showed basic surface functionality at
pHPZC at 10.3, and a phenol adsorption capacity that was higher than
that of commercial Norit (RO 0.8) AC. Thus, it is feasible to develop
better quality low-cost AC from (Pinus patula) sawdust using twostage
N2-steam activation in fixed-bed reactor.
Abstract: Problem Statement:Rapid technological developments of the 21st century have advanced our daily lives in various ways. Particularly in education, students frequently utilize technological resources to aid their homework and to access information. listen to radio or watch television (26.9 %) and e-mails (34.2 %) [26]. Not surprisingly, the increase in the use of technologies also resulted in an increase in the use of e-mail, instant messaging, chat rooms, mobile phones, mobile phone cameras and web sites by adolescents to bully peers. As cyber bullying occurs in the cyber space, lesser access to technologies would mean lesser cyber-harm. Therefore, the frequency of technology use is a significant predictor of cyber bullying and cyber victims. Cyber bullies try to harm the victim using various media. These tools include sending derogatory texts via mobile phones, sending threatening e-mails and forwarding confidential emails to everyone on the contacts list. Another way of cyber bullying is to set up a humiliating website and invite others to post comments. In other words, cyber bullies use e-mail, chat rooms, instant messaging, pagers, mobile texts and online voting tools to humiliate and frighten others and to create a sense of helplessness. No matter what type of bullying it is, it negatively affects its victims. Children who bully exhibit more emotional inhibition and attribute themselves more negative self-statements compared to non-bullies. Students whose families are not sympathetic and who receive lower emotional support are more prone to bully their peers. Bullies have authoritarian families and do not get along well with them. The family is the place where the children-s physical, social and psychological needs are satisfied and where their personalities develop. As the use of the internet became prevalent so did parents- restrictions on their children-s internet use. However, parents are unaware of the real harm. Studies that explain the relationship between parental attitudes and cyber bullying are scarce in literature. Thus, this study aims to investigate the relationship between cyber bullying and parental attitudes in the primary school. Purpose of Study: This study aimed to investigate the relationship between cyber bullying and parental attitudes. A second aim was to determine whether parental attitudes could predict cyber bullying and if so which variables could predict it significantly. Methods:The study had a cross-sectional and relational survey model. A demographics information form, questions about cyber bullying and a Parental Attitudes Inventory were conducted with a total of 346 students (189 females and 157 males) registered at various primary schools. Data was analysed by multiple regression analysis using the software package SPSS 16.
Abstract: The dynamic or complex modulus test is considered
to be a mechanistically based laboratory test to reliably characterize
the strength and load-resistance of Hot-Mix Asphalt (HMA) mixes
used in the construction of roads. The most common observation is
that the data collected from these tests are often noisy and somewhat
non-sinusoidal. This hampers accurate analysis of the data to obtain
engineering insight. The goal of the work presented in this paper is to
develop and compare automated evolutionary computational
techniques to filter test noise in the collection of data for the HMA
complex modulus test. The results showed that the Covariance
Matrix Adaptation-Evolutionary Strategy (CMA-ES) approach is
computationally efficient for filtering data obtained from the HMA
complex modulus test.
Abstract: This paper discusses two observers, which are used
for the estimation of parameters of PMSM. Former one, reduced
order observer, which is used to estimate the inaccessible parameters
of PMSM. Later one, full order observer, which is used to estimate
all the parameters of PMSM even though some of the parameters are
directly available for measurement, so as to meet with the
insensitivity to the parameter variation. However, the state space
model contains some nonlinear terms i.e. the product of different
state variables. The asymptotic state observer, which approximately
reconstructs the state vector for linear systems without uncertainties,
was presented by Luenberger. In this work, a modified form of such
an observer is used by including a non-linear term involving the
speed. So, both the observers are designed in the framework of
nonlinear control; their stability and rate of convergence is discussed.
Abstract: Equilibrium and stability equations of a thin rectangular plate with length a, width b, and thickness h(x)=C1x+C2, made of functionally graded materials under thermal loads are derived based on the first order shear deformation theory. It is assumed that the material properties vary as a power form of thickness coordinate variable z. The derived equilibrium and buckling equations are then solved analytically for a plate with simply supported boundary conditions. One type of thermal loading, uniform temperature rise and gradient through the thickness are considered, and the buckling temperatures are derived. The influences of the plate aspect ratio, the relative thickness, the gradient index and the transverse shear on buckling temperature difference are all discussed.
Abstract: In this paper the modeling and analysis of Space
Vector Pulse Width Modulation (SVPWM) based Dynamic Voltage
Restorer (DVR) using PSCAD/EMTDC software will be presented in
details. The simulation includes full modeling of the SVPWM
technique used to control the DVR inverter. A test power system
composed of three phase voltage source, sag generator, DVR and
three phase resistive load is used to demonstrate restoration capability
of the DVR. The simulation results of the presented DVR proved
excellent voltage sag mitigation to protect sensitive loads.
Abstract: Primary studies are being carried out in Turkey for
expanding information and communication technologies (ICT) aided instruction activities. Subject of the present study is to identify
whether those studies achieved their goals in the application. Information technologies (IT) formative teachers in the primary
schools, and academicians in the faculties of education were interviewed to investigate the process and results of implementing
computer-aided instruction methods whose basis is strengthened in theory. Analysis of the results gained from two separate surveys
demonstrated that capability of the teachers in elementary education institutions for carrying into effect computer-aided instruction and
technical infrastructure has not been established for computer-aided instruction practices yet. Prospective teachers must be well-equipped in ICT to duly fulfill requirements of modern education and also
must be self-confident. Finally, scope and intensity of the courses given in connection with teaching of the ICT in faculties of education needs to be revised.
Abstract: Explosive welding is a process which uses explosive
detonation to move the flyer plate material into the base material to
produce a solid state joint. Experimental tests have been carried out
by other researchers; have been considered to explosively welded
aluminium 7039 and steel 4340 tubes in one step. The tests have been
done using various stand-off distances and explosive ratios. Various
interface geometries have been obtained from these experiments. In
this paper, all the experiments carried out were simulated using the
finite element method. The flyer plate and collision velocities
obtained from the analysis were validated by the pin-measurement
experiments. The numerical results showed that very high localized
plastic deformation produced at the bond interface. The
Ls_dyna_971 FEM has been used for all simulation process.
Abstract: This study presents an exact general solution for
steady-state conductive heat transfer in cylindrical composite
laminates. Appropriate Fourier transformation has been obtained
using Sturm-Liouville theorem. Series coefficients are achieved by
solving a set of equations that related to thermal boundary conditions
at inner and outer of the cylinder, also related to temperature
continuity and heat flux continuity between each layer. The solution
of this set of equations are obtained using Thomas algorithm. In this
paper, the effect of fibers- angle on temperature distribution of
composite laminate is investigated under general boundary
conditions. Here, we show that the temperature distribution for any
composite laminates is between temperature distribution for
laminates with θ = 0° and θ = 90° .
Abstract: Analyse of locally manufactured Low Density Polyethylene (LDPE) durability, used within lining systems at bottom of Municipal Solid Waste (landfill), is done in the present work. For this end, short and middle time creep behavior under tension of the analyzed material is carried out. The locally manufactured material is tested and compared to the European one (LDPE-CE). Both materials was tested in 03 various mediums: ambient and two aggressive (salty water and foam water), using three specimens in each case. A testing campaign is carried out using an especially designed and achieved testing bench. Moreover, characterisation tests were carried out to evaluate the medium effect on the mechanical properties of the tested material (LDPE). Furthermore, experimental results have been used to establish a law regression which can be used to predict creep behaviour of the analyzed material. As a result, the analyzed LDPE material has showed a good stability in different ambient and aggressive mediums; as well, locally manufactured LDPE seems more flexible, compared with the European one. This makes it more useful to the desired application.
Abstract: Luneberg lens is a new generation of antennas that is
developed in the last few years and inserts itself strongly in
Microwaves, Communications and Telescopes area. The idea of this
research is to improve the radiation pattern by decreasing the side
lobes and increasing the main lobe. The new design is proposed to
work in the X-band. The simulated result and analysis are presented.
Abstract: Schema matching plays a key role in many different
applications, such as schema integration, data integration, data
warehousing, data transformation, E-commerce, peer-to-peer data
management, ontology matching and integration, semantic Web,
semantic query processing, etc. Manual matching is expensive and
error-prone, so it is therefore important to develop techniques to
automate the schema matching process. In this paper, we present a
solution for XML schema automated matching problem which
produces semantic mappings between corresponding schema
elements of given source and target schemas. This solution
contributed in solving more comprehensively and efficiently XML
schema automated matching problem. Our solution based on
combining linguistic similarity, data type compatibility and structural
similarity of XML schema elements. After describing our solution,
we present experimental results that demonstrate the effectiveness of
this approach.
Abstract: Distance protection of transmission lines including advanced flexible AC transmission system (FACTS) devices has been a very challenging task. FACTS devices of interest in this paper are static synchronous series compensators (SSSC) and unified power flow controller (UPFC). In this paper, a new algorithm is proposed to detect and classify the fault and identify the fault position in a transmission line with respect to a FACTS device placed in the midpoint of the transmission line. Discrete wavelet transformation and wavelet entropy calculations are used to analyze during fault current and voltage signals of the compensated transmission line. The proposed algorithm is very simple and accurate in fault detection and classification. A variety of fault cases and simulation results are introduced to show the effectiveness of such algorithm.
Abstract: The effects of equilibrium time, solution pH, and
sorption temperature of cationic methylene blue (MB) adsorption on nanoporous metallosilicoaluminophosphate ZnAPSO-34 was studied
using a batch equilibration method. UV–VIS spectroscopy was used
to obtain the adsorption isotherms at 20° C. The optimum period for
adsorption was 300 min. However, MB removal increased from
81,82 % to 94,81 %. The equilibrium adsorption data was analyzed
by using Langmuir, Freundlich and Temkin isotherm models.
Langmuir isotherm was found to be the better-fitting model and the process followed pseudo second–order kinetics. The results showed
that ZnAPSO-34 could be employed as an effective material and could be an attractive alternative for the removal of dyes and colors
from aqueous solutions.
Abstract: A new method for color image segmentation using fuzzy logic is proposed in this paper. Our aim here is to automatically produce a fuzzy system for color classification and image segmentation with least number of rules and minimum error rate. Particle swarm optimization is a sub class of evolutionary algorithms that has been inspired from social behavior of fishes, bees, birds, etc, that live together in colonies. We use comprehensive learning particle swarm optimization (CLPSO) technique to find optimal fuzzy rules and membership functions because it discourages premature convergence. Here each particle of the swarm codes a set of fuzzy rules. During evolution, a population member tries to maximize a fitness criterion which is here high classification rate and small number of rules. Finally, particle with the highest fitness value is selected as the best set of fuzzy rules for image segmentation. Our results, using this method for soccer field image segmentation in Robocop contests shows 89% performance. Less computational load is needed when using this method compared with other methods like ANFIS, because it generates a smaller number of fuzzy rules. Large train dataset and its variety, makes the proposed method invariant to illumination noise
Abstract: Recently, fast neural networks for object/face
detection were presented in [1-3]. The speed up factor of these
networks relies on performing cross correlation in the frequency
domain between the input image and the weights of the hidden
layer. But, these equations given in [1-3] for conventional and fast
neural networks are not valid for many reasons presented here. In
this paper, correct equations for cross correlation in the spatial and
frequency domains are presented. Furthermore, correct formulas for
the number of computation steps required by conventional and fast
neural networks given in [1-3] are introduced. A new formula for
the speed up ratio is established. Also, corrections for the equations
of fast multi scale object/face detection are given. Moreover,
commutative cross correlation is achieved. Simulation results show
that sub-image detection based on cross correlation in the frequency
domain is faster than classical neural networks.
Abstract: Multi User Virtual Worlds are becoming a valuable educational tool. Learning experiences within these worlds focus on discovery and active experiences that both engage students and motivate them to explore new concepts. As educators, we need to explore these environments to determine how they can most effectively be used in our instructional practices. This paper explores the current application of virtual worlds to identify meaningful educational strategies that are being used to engage students and enhance teaching and learning.
Abstract: In the present work, a study has been made on the combination of the electrical discharge machining (EDM) with ultrasonic vibrations to improve the machining efficiency. In experiments the graphite used as tool electrode and material of workpiece was AISIH13 tool steel. The parameters such as discharge peak current and pulse duration were changed to explore their effect on the material removal rate (MRR), relative tool wear ratio (TWR) and surface roughness. From the experimental result it can be seen that ultrasonic vibration of the workpiece can significantly reduces the inactive pulses and improves the stability of process. It was found that ultrasonic assisted EDM (US-EDM) is effective in attaining a high material removal rate (MRR) in finishing regime.
Abstract: This paper considers the autonomous navigation
problem of multiple n-link nonholonomic mobile manipulators within
an obstacle-ridden environment. We present a set of nonlinear
acceleration controllers, derived from the Lyapunov-based control
scheme, which generates collision-free trajectories of the mobile
manipulators from initial configurations to final configurations in a
constrained environment cluttered with stationary solid objects of
different shapes and sizes. We demonstrate the efficiency of the
control scheme and the resulting acceleration controllers of the
mobile manipulators with results through computer simulations of an
interesting scenario.