Abstract: Bubble columns have a variety of applications in
absorption, bio-reactions, catalytic slurry reactions, and coal
liquefaction; because they are simple to operate, provide good heat
and mass transfer, having less operational cost. The use of
Computational Fluid Dynamics (CFD) for bubble column becomes
important, since it can describe the fluid hydrodynamics on both local
and global scale. Euler- Euler two-phase fluid model has been used to
simulate two-phase (air and water) transient up-flow in bubble
column (15cm diameter) using FLUENT6.3. These simulations and
experiments were operated over a range of superficial gas velocities
in the bubbly flow and churn turbulent regime (1 to16 cm/s) at
ambient conditions. Liquid velocity was varied from 0 to 16cm/s. The
turbulence in the liquid phase is described using the standard k-ε
model. The interactions between the two phases are described
through drag coefficient formulations (Schiller Neumann). The
objectives are to validate CFD simulations with experimental data,
and to obtain grid-independent numerical solutions. Quantitatively
good agreements are obtained between experimental data for hold-up
and simulation values. Axial liquid velocity profiles and gas holdup
profiles were also obtained for the simulation.
Abstract: This article gives a short preview of the new software
created especially for palletizing process in automated production
systems. Each chapter of this article is about problem solving in
development of modules in Java programming language. First part
describes structure of the software, its modules and data flow
between them. Second part describes all deployment methods, which
are implemented in the software. Next chapter is about twodimensional
editor created for manipulation with objects in each
layer of the load and gives calculations for collision control. Module
of virtual reality used for three-dimensional preview and creation of
the load is described in the fifth chapter. The last part of this article
describes communication and data flow between control system of
the robot, vision system and software.
Abstract: This paper presents a new methodology to select test
cases from regression test suites. The selection strategy is based on
analyzing the dynamic behavior of the applications that written in
any programming language. Methods based on dynamic analysis are
more safe and efficient. We design a technique that combine the code
based technique and model based technique, to allow comparing the
object oriented of an application that written in any programming
language. We have developed a prototype tool that detect changes
and select test cases from test suite.
Abstract: The objective of this work was to investigate flow
properties of powdered infant formula samples. Samples were
purchased at a local pharmacy and differed in composition. Lactose
free infant formula, gluten free infant formula and infant formulas
containing dietary fibers and probiotics were tested and compared
with a regular infant formula sample which did not contain any of
these supplements. Particle size and bulk density were determined
and their influence on flow properties was discussed. There were no
significant differences in bulk densities of the samples, therefore the
connection between flow properties and bulk density could not be
determined. Lactose free infant formula showed flow properties
different to standard supplement-free sample. Gluten free infant
formula with addition of probiotic microorganisms and dietary fiber
had the narrowest particle size distribution range and exhibited the
best flow properties. All the other samples exhibited the same
tendency of decreasing compaction coefficient with increasing flow
speed, which means they all become freer flowing with higher flow
speeds.
Abstract: Many real-world data sets consist of a very high dimensional feature space. Most clustering techniques use the distance or similarity between objects as a measure to build clusters. But in high dimensional spaces, distances between points become relatively uniform. In such cases, density based approaches may give better results. Subspace Clustering algorithms automatically identify lower dimensional subspaces of the higher dimensional feature space in which clusters exist. In this paper, we propose a new clustering algorithm, ISC – Intelligent Subspace Clustering, which tries to overcome three major limitations of the existing state-of-art techniques. ISC determines the input parameter such as є – distance at various levels of Subspace Clustering which helps in finding meaningful clusters. The uniform parameters approach is not suitable for different kind of databases. ISC implements dynamic and adaptive determination of Meaningful clustering parameters based on hierarchical filtering approach. Third and most important feature of ISC is the ability of incremental learning and dynamic inclusion and exclusions of subspaces which lead to better cluster formation.
Abstract: This paper presents a new and efficient approach for
capacitor placement in radial distribution systems that determine
the optimal locations and size of capacitor with an objective of
improving the voltage profile and reduction of power loss. The
solution methodology has two parts: in part one the loss sensitivity
factors are used to select the candidate locations for the capacitor
placement and in part two a new algorithm that employs Plant growth
Simulation Algorithm (PGSA) is used to estimate the optimal size
of capacitors at the optimal buses determined in part one. The main
advantage of the proposed method is that it does not require any
external control parameters. The other advantage is that it handles the
objective function and the constraints separately, avoiding the trouble
to determine the barrier factors. The proposed method is applied to 9
and 34 bus radial distribution systems. The solutions obtained by the
proposed method are compared with other methods. The proposed
method has outperformed the other methods in terms of the quality
of solution.
Abstract: Low power consumption is a major constraint for battery-powered system like computer notebook or PDA. In the past, specialists usually designed both specific optimized equipments and codes to relief this concern. Doing like this could work for quite a long time, however, in this era, there is another significant restraint, the time to market. To be able to serve along the power constraint while can launch products in shorter production period, objectoriented programming (OOP) has stepped in to this field. Though everyone knows that OOP has quite much more overhead than assembly and procedural languages, development trend still heads to this new world, which contradicts with the target of low power consumption. Most of the prior power related software researches reported that OOP consumed much resource, however, as industry had to accept it due to business reasons, up to now, no papers yet had mentioned about how to choose the best OOP practice in this power limited boundary. This article is the pioneer that tries to specify and propose the optimized strategy in writing OOP software under energy concerned environment, based on quantitative real results. The language chosen for studying is C# based on .NET Framework 2.0 which is one of the trendy OOP development environments. The recommendation gotten from this research would be a good roadmap that can help developers in coding that well balances between time to market and time of battery.
Abstract: To make use of the limited amounts of water in arid
region, the Iranians developed man-made underground water
channels called qanats (kanats) .In fact, qanats may be considered as
the first long-distance water transfer system. Qanats are an ancient
water transfer system found in arid regions wherein groundwater
from mountainous areas, aquifers and sometimes from rivers, was
brought to points of re-emergence such as an oasis, through one or
more underground tunnels. The tunnels, many of which were
kilometers in length, had designed for slopes to provide gravitational
flow. The tunnels allowed water to drain out to the surface by gravity
to supply water to lower and flatter agricultural land.
Qanats have been an ancient, sustainable system facilitating the
harvesting of water for centuries in Iran, and more than 35 additional
countries of the world such as India, Arabia, Egypt, North Africa,
Spain and even to New world.
There are about 22000 qanats in Iran with 274000 kilometers of
underground conduits all built by manual labor. The amount of
water of the usable qanats of Iran produce is altogether 750 to
1000 cubic meter per second. The longest chain of qanat is
situated in Gonabad region in Khorasan province. It is 70
kilometers long. Qanats are renewable water supply systems that
have sustained agricultural settlement on the Iranian plateau for
millennia. The great advantages of Qanats are no evaporation
during transit, little seepage , no raising of the water- table and no
pollution in the area surrounding the conduits. Qanat systems
have a profound influence on the lives of the water users in Iran, and
conform to Iran-s climate. Qanat allows those living in a desert
environment adjacent to a mountain watershed to create a large oasis
in an otherwise stark environment.
This paper explains qanats structure designs, their history,
objectives causing their creation, construction materials, locations
and their importance in different times, as well as their present
sustainable role in Iran.
Abstract: The objective of this research was to study the career
success and the satisfaction of female executives working for schools
in Bangkok, Thailand. This paper drew upon the survey data
collected from 68 female executives. The survey conducted in on
Bangkok schools. The statistics utilized in this paper included
percentage, mean, standard deviation as well as t-test. The findings
revealed that the majority of samples had more than 30 years of
experience, held a master degree, and had an average income of less
than 40,000 baht. The majority of respondents worked not more than
50 hours per week. In addition, the mean score revealed career
development was ranked as their number one career satisfaction and
having a job related to education was ranked as their number one job
satisfaction. Also, the mean score of all categories of satisfaction was
4.61 with standard deviation of 1.677 which indicated that female
executive level of satisfaction was high. In terms of the subjectivity
career success, the hypothesis testing’s result disclosed that female
executives with different married status had a difference in their job
satisfaction which was significant at the 0.05 confidence level.
Abstract: This paper presents the influence of distributed generation (DG) on congestion and locational marginal price (LMP) in an optimal power flow (OPF) based wholesale electricity market. The problem of optimal placement to manage congestion and reduce LMP is formulated for the objective of social welfare maximization. From competitive electricity market standpoint, DGs have great value when they reduce load in particular locations and at particular times when feeders are heavily loaded. The paper lies on the groundwork that solution to optimal mix of generation and transmission resources can be achieved by addressing congestion and corresponding LMP. Obtained as lagrangian multiplier associated with active power flow equation for each node, LMP gives the short run marginal cost (SRMC) of electricity. Specific grid locations are examined to study the influence of DG penetration on congestion and corresponding shadow prices. The influence of DG on congestion and locational marginal prices has been demonstrated in a modified IEEE 14 bus test system.
Abstract: The distribution of macrobenthic polychaetes along
the coastal waters of Penang National Park was surveyed to estimate
the effect of various environmental parameters at three stations
(200m, 600m and 1200m) from the shoreline, during six sampling
months, from June 2010 to April 2011.The use of polychaetes in
descriptive ecology is surveyed in the light of a recent investigation
particularly concerning the soft bottom biota environments.
Polychaetes, often connected in the former to the notion of
opportunistic species able to proliferate after an enhancement in
organic matter, had performed a momentous role particularly with
regard to effected soft-bottom habitats. The objective of this survey
was to investigate different environment stress over soft bottom
polychaete community along Teluk Ketapang and Pantai Acheh
(Penang National Park) over a year period. Variations in the
polychaete community were evaluated using univariate and
multivariate methods. The results of PCA analysis displayed a
positive relation between macrobenthic community structures and
environmental parameters such as sediment particle size and organic
matter in the coastal water. A total of 604 individuals were examined
which was grouped into 23 families. Family Nereidae was the most
abundant (22.68%), followed by Spionidae (22.02%), Hesionidae
(12.58%), Nephtylidae (9.27%) and Orbiniidae (8.61%). It is
noticeable that good results can only be obtained on the basis of good
taxonomic resolution. We proposed that, in monitoring surveys,
operative time could be optimized not only by working at a highertaxonomic
level on the entire macrobenthic data set, but by also
choosing an especially indicative group and working at lower
taxonomic and good level.
Abstract: The purpose of the paper is to develop an informationcontrol environment for overall management and self-reconfiguration of the reconfigurable multifunctional machine tool for machining both rotation and prismatic parts and high concentration of different technological operations - turning, milling, drilling, grinding, etc. For the realization of this purpose on the basis of defined sub-processes for the implementation of the technological process, architecture of the information-search system for machine control is suggested. By using the object-oriented method, a structure and organization of the search system based on agents and manager with central control are developed. Thus conditions for identification of available information in DBs, self-reconfiguration of technological system and entire control of the reconfigurable multifunctional machine tool are created.
Abstract: Sudoku is a kind of logic puzzles. Each puzzle consists
of a board, which is a 9×9 cells, divided into nine 3×3 subblocks
and a set of numbers from 1 to 9. The aim of this puzzle is to
fill in every cell of the board with a number from 1 to 9 such
that in every row, every column, and every subblock contains each
number exactly one. Sudoku puzzles belong to combinatorial problem
(NP complete). Sudoku puzzles can be solved by using a variety of
techniques/algorithms such as genetic algorithms, heuristics, integer
programming, and so on. In this paper, we propose a new approach for
solving Sudoku which is by modelling them as block-world problems.
In block-world problems, there are a number of boxes on the table
with a particular order or arrangement. The objective of this problem
is to change this arrangement into the targeted arrangement with the
help of two types of robots. In this paper, we present three models
for Sudoku. We modellized Sudoku as parameterized multi-agent
systems. A parameterized multi-agent system is a multi-agent system
which consists of several uniform/similar agents and the number of
the agents in the system is stated as the parameter of this system. We
use Temporal Logic of Actions (TLA) for formalizing our models.
Abstract: Supply chain management has become more
challenging with the emerging trend of globalization and
sustainability. Lately, research related to perishable products supply
chains, in particular agricultural food products, has emerged. This is
attributed to the additional complexity of managing this type of
supply chains with the recently increased concern of public health,
food quality, food safety, demand and price variability, and the
limited lifetime of these products. Inventory management for agrifood
supply chains is of vital importance due to the product
perishability and customers- strive for quality. This paper
concentrates on developing a simulation model of a real life case
study of a two echelon production-distribution system for agri-food
products. The objective is to improve a set of performance measures
by developing a simulation model that helps in evaluating and
analysing the performance of these supply chains. Simulation results
showed that it can help in improving overall system performance.
Abstract: Efficient retrieval of multimedia objects has gained enormous focus in recent years. A number of techniques have been suggested for retrieval of textual information; however, relatively little has been suggested for efficient retrieval of multimedia objects. In this paper we have proposed a generic architecture for contextaware retrieval of multimedia objects. The proposed framework combines the well-known approaches of text-based retrieval and context-aware retrieval to formulate architecture for accurate retrieval of multimedia data.
Abstract: The objective of this paper is to analyse the
application of the Half-Sweep Gauss-Seidel (HSGS) method by using
the Half-sweep approximation equation based on central difference
(CD) and repeated trapezoidal (RT) formulas to solve linear fredholm
integro-differential equations of first order. The formulation and
implementation of the Full-Sweep Gauss-Seidel (FSGS) and Half-
Sweep Gauss-Seidel (HSGS) methods are also presented. The HSGS
method has been shown to rapid compared to the FSGS methods.
Some numerical tests were illustrated to show that the HSGS method
is superior to the FSGS method.
Abstract: In this paper, multiobjective design of multi-machine Power System Stabilizers (PSSs) using Particle Swarm Optimization (PSO) is presented. The stabilizers are tuned to simultaneously shift the lightly damped and undamped electro-mechanical modes of all machines to a prescribed zone in the s-plane. A multiobjective problem is formulated to optimize a composite set of objective functions comprising the damping factor, and the damping ratio of the lightly damped electromechanical modes. The PSSs parameters tuning problem is converted to an optimization problem which is solved by PSO with the eigenvalue-based multiobjective function. The proposed PSO based PSSs is tested on a multimachine power system under different operating conditions and disturbances through eigenvalue analysis and some performance indices to illustrate its robust performance.
Abstract: Surveillance system is widely used in the traffic
monitoring. The deployment of cameras is moving toward a
ubiquitous camera (UbiCam) environment. In our previous study, a
novel service, called GPS-VT, was firstly proposed by incorporating
global positioning system (GPS) and visual tracking techniques for
the UbiCam environment. The first prototype is called GODTA
(GPS-based Moving Object Detection and Tracking Approach). For a
moving person carried GPS-enabled mobile device, he can be
tracking when he enters the field-of-view (FOV) of a camera
according to his real-time GPS coordinate. In this paper, GPS-VT
service is applied to the tracking of vehicles. The moving speed of a
vehicle is much faster than a person. It means that the time passing
through the FOV is much shorter than that of a person. Besides, the
update interval of GPS coordinate is once per second, it is
asynchronous with the frame rate of the real-time image. The above
asynchronous is worsen by the network transmission delay. These
factors are the main challenging to fulfill GPS-VT service on a
vehicle.In order to overcome the influence of the above factors, a
back-propagation neural network (BPNN) is used to predict the
possible lane before the vehicle enters the FOV of a camera. Then, a
template matching technique is used for the visual tracking of a target
vehicle. The experimental result shows that the target vehicle can be
located and tracking successfully. The success location rate of the
implemented prototype is higher than that of the previous GODTA.
Abstract: In the domain of machine vision, the
measurement of length is done using cameras where the
accuracy is directly proportional to the resolution of the
camera and inversely to the size of the object. Since most of
the pixels are wasted imaging the entire body as opposed to
just imaging the edges in a conventional system, a double
aperture system is constructed to focus on the edges to
measure at higher resolution. The paper discusses the
complexities and how they are mitigated to realize a practical
machine vision system.
Abstract: Least Development Countries (LDC) like
Bangladesh, whose 25% revenue earning is achieved from Textile
export, requires producing less defective textile for minimizing
production cost and time. Inspection processes done on these
industries are mostly manual and time consuming. To reduce error
on identifying fabric defects requires more automotive and
accurate inspection process. Considering this lacking, this research
implements a Textile Defect Recognizer which uses computer
vision methodology with the combination of multi-layer neural
networks to identify four classifications of textile defects. The
recognizer, suitable for LDC countries, identifies the fabric defects
within economical cost and produces less error prone inspection
system in real time. In order to generate input set for the neural
network, primarily the recognizer captures digital fabric images by
image acquisition device and converts the RGB images into binary
images by restoration process and local threshold techniques.
Later, the output of the processed image, the area of the faulty
portion, the number of objects of the image and the sharp factor of
the image, are feed backed as an input layer to the neural network
which uses back propagation algorithm to compute the weighted
factors and generates the desired classifications of defects as an
output.