Abstract: The present study is concerned with the effect of
exciting boundary layer on cooling process in a gas-turbine blades.
The cooling process is numerically investigated. Observations show
cooling the first row of moving or stable blades leads to increase
their life-time. Results show that minimum temperature in cooling
line with exciting boundary layer is lower than without exciting.
Using block in cooling line of turbines' blade causes flow pattern and
stability in boundary layer changed that causes increase in heat
transfer coefficient. Results show at the location of block,
temperature of turbines' blade is significantly decreased. The k-ε
turbulence model is used.
Abstract: In this study, the numerical solution of unsteady flow
between two concentric rotating spheres with suction and blowing at
their boundaries is presented. The spheres are rotating about a
common axis of rotation while their angular velocities are constant.
The Navier-Stokes equations are solved by employing the finite
difference method and implicit scheme. The resulting flow patterns
are presented for various values of the flow parameters including
rotational Reynolds number Re , and a blowing/suction Reynolds
number Rew . Viscous torques at the inner and the outer spheres are
calculated, too. It is seen that increasing the amount of suction and
blowing decrease the size of eddies generated in the annulus.
Abstract: This paper studies dynamic stability of homogeneous
beams with piezoelectric layers subjected to periodic axial
compressive load that is simply supported at both ends lies on a
continuous elastic foundation. The displacement field of beam is
assumed based on Bernoulli-Euler beam theory. Applying the
Hamilton's principle, the governing dynamic equation is established.
The influences of applied voltage, foundation coefficient and
piezoelectric thickness on the unstable regions are presented. To
investigate the accuracy of the present analysis, a compression study
is carried out with a known data.
Abstract: The main issue in sweetening natural gas is H2S
dissociation. The present study is concerned with simulating thermal
dissociation of H2S in industrial natural gas carbon black furnace.
The comparison of calculated results against experimental
measurements shows good agreement. The results show that sulfur
derived from H2S thermal dissociation peaked at φ=0.95. H2S
thermal dissociation is enhanced in equivalence ratio upper than 1
and H2S oxidization is increased in equivalence ratio lower than 1.
H2 concentration of H2S thermal dissociation is increased with
increase of equivalence ratio up to 1. Also, H2S concentration
decreased in outlet as equivalence ratio increases. H2S thermal
dissociation to hydrogen and Sulfur reduces its toxic characteristics
and make economical benefits.
Abstract: Majority of pepper farmers in Malaysia are using the
open-sun method for drying the pepper berries. This method is time
consuming and exposed the berries to rain and contamination. A
maintenance-friendly and properly enclosed dryer is therefore
desired. A dryer design with a solar collector and a chimney was
studied and adapted to suit the needs of small-scale pepper farmers in
Malaysia. The dryer will provide an environment with an optimum
operating temperature meant for drying pepper berries. The dryer
model was evaluated by using commercially available computational
fluid dynamic (CFD) software in order to understand the heat and
mass transfer inside the dryer. Natural convection was the only mode
of heat transportation considered in this study as in accordance to the
idea of having a simple and maintenance-friendly design. To
accommodate the effect of low buoyancy found in natural convection
driers, a biomass burner was integrated into the solar dryer design.
Abstract: This study compares three meta heuristics to minimize makespan (Cmax) for Hybrid Flow Shop (HFS) Scheduling Problem with Parallel Machines. This problem is known to be NP-Hard. This study proposes three algorithms among improvement heuristic searches which are: Genetic Algorithm (GA), Simulated Annealing (SA), and Tabu Search (TS). SA and TS are known as deterministic improvement heuristic search. GA is known as stochastic improvement heuristic search. A comprehensive comparison from these three improvement heuristic searches is presented. The results for the experiments conducted show that TS is effective and efficient to solve HFS scheduling problems.
Abstract: Actual load, material characteristics and other
quantities often differ from the design values. This can cause worse
function, shorter life or failure of a civil engineering structure, a
machine, vehicle or another appliance. The paper shows main causes
of the uncertainties and deviations and presents a systematic
approach and efficient tools for their elimination or mitigation of
consequences. Emphasis is put on the design stage, which is most
important for reliability ensuring. Principles of robust design and
important tools are explained, including FMEA, sensitivity analysis
and probabilistic simulation methods. The lifetime prediction of
long-life objects can be improved by long-term monitoring of the
load response and damage accumulation in operation. The condition
evaluation of engineering structures, such as bridges, is often based
on visual inspection and verbal description. Here, methods based on
fuzzy logic can reduce the subjective influences.