Abstract: Refractive index control of benzocyclobutene (BCB 4024-40) is achieved by facilitating different conditions during the thermal curing of BCB film. Refractive index (RI) change of 1.49% is obtained with curing of BCB film using an oven, while the RI change is 0.1% when the BCB is cured using a hotplate. The two different curing methods exhibit a temperature dependent refractive index change of the BCB photosensitive polymer. By carefully controlling the curing conditions, multiple layers of BCB with different RI can be fabricated, which can then be applied in the fabrication of optical waveguides.
Abstract: The present study has been carried out with a view to calculate the coastal vulnerability index (CVI) to know the high and low sensitive areas and area of inundation due to future SLR. Both conventional and remotely sensed data were used and analyzed through the modelling technique. Out of the total study area, 8.26% is very high risk, 14.21% high, 9.36% medium, 22.46% low and 7.35% in the very low vulnerable category, due to costal components. Results of the inundation analysis indicate that 225.2 km² and 397 km² of the land area will be submerged by flooding at 1m and 10m inundation levels. The most severely affected sectors are expected to be the residential, industrial and recreational areas. As this coast is planned for future coastal developmental activities, measures such as industrializations, building regulation, urban growth planning and agriculture, development of an integrated coastal zone management, strict enforcement of the Coastal Regulation Zone (CRZ) Act, monitoring of impacts and further research in this regard are recommended for the study area.
Abstract: Deformable active contours are widely used in
computer vision and image processing applications for image
segmentation, especially in biomedical image analysis. The active
contour or “snake" deforms towards a target object by controlling the
internal, image and constraint forces. However, if the contour
initialized with a lesser number of control points, there is a high
probability of surpassing the sharp corners of the object during
deformation of the contour. In this paper, a new technique is
proposed to construct the initial contour by incorporating prior
knowledge of significant corners of the object detected using the
Harris operator. This new reconstructed contour begins to deform, by
attracting the snake towards the targeted object, without missing the
corners. Experimental results with several synthetic images show the
ability of the new technique to deal with sharp corners with a high
accuracy than traditional methods.
Abstract: In this work a surgical simulator is produced which
enables a training otologist to conduct a virtual, real-time prosthetic
insertion. The simulator provides the Ear, Nose and Throat surgeon
with real-time visual and haptic responses during virtual cochlear
implantation into a 3D model of the human Scala Tympani (ST). The
parametric model is derived from measured data as published in the
literature and accounts for human morphological variance, such as
differences in cochlear shape, enabling patient-specific pre- operative
assessment. Haptic modeling techniques use real physical data and
insertion force measurements, to develop a force model which
mimics the physical behavior of an implant as it collides with the ST
walls during an insertion. Output force profiles are acquired from the
insertion studies conducted in the work, to validate the haptic model.
The simulator provides the user with real-time, quantitative insertion
force information and associated electrode position as user inserts the
virtual implant into the ST model. The information provided by this
study may also be of use to implant manufacturers for design
enhancements as well as for training specialists in optimal force
administration, using the simulator. The paper reports on the methods
for anatomical modeling and haptic algorithm development, with
focus on simulator design, development, optimization and validation.
The techniques may be transferrable to other medical applications
that involve prosthetic device insertions where user vision is
obstructed.
Abstract: Undoubtedly, chassis is one of the most important
parts of a vehicle. Chassis that today are produced for vehicles are
made up of four parts. These parts are jointed together by screwing.
Transverse parts are called cross member.
This study reviews the stress generated by cyclic laboratory loads
in front cross member of Peugeot 405. In this paper the finite element
method is used to simulate the welding process and to determine the
physical response of the spot-welded joints. Analysis is done by the
Abaqus software.
The Stresses generated in cross member structure are generally
classified into two groups: The stresses remained in form of residual
stresses after welding process and the mechanical stress generated by
cyclic load. Accordingly the total stress must be obtained by
determining residual stress and mechanical stress separately and then
sum them according to the superposition principle.
In order to improve accuracy, material properties including
physical, thermal and mechanical properties were supposed to be
temperature-dependent. Simulation shows that maximum Von Misses
stresses are located at special points. The model results are then
compared to the experimental results which are reported by
producing factory and good agreement is observed.
Abstract: The oil and gas industry has moved towards Load and
Resistance Factor Design through API RP2A - LRFD and the
recently published international standard, ISO-19902, for design of
fixed steel offshore structures. The ISO 19902 is intended to provide
a harmonized design practice that offers a balanced structural fitness
for the purpose, economy and safety. As part of an ongoing work, the
reliability analysis of tubular joints of the jacket structure has been
carried out to calibrate the load and resistance factors for the design
of offshore platforms in Malaysia, as proposed in the ISO.
Probabilistic models have been established for the load effects (wave,
wind and current) and the tubular joints strengths. In this study the
First Order Reliability Method (FORM), coded in MATLAB
Software has been employed to evaluate the reliability index of the
typical joints, designed using API RP2A - WSD and ISO 19902.
Abstract: Short term electricity demand forecasts are required
by power utilities for efficient operation of the power grid. In a
competitive market environment, suppliers and large consumers also
require short term forecasts in order to estimate their energy
requirements in advance. Electricity demand is influenced (among
other things) by the day of the week, the time of year and special
periods and/or days such as Ramadhan, all of which must be
identified prior to modelling. This identification, known as day-type
identification, must be included in the modelling stage either by
segmenting the data and modelling each day-type separately or by
including the day-type as an input. Day-type identification is the
main focus of this paper. A Kohonen map is employed to identify the
separate day-types in Algerian data.
Abstract: Dr Eliyahu Goldratt has done the pioneering work in
the development of Theory of Constraints. Since then, many more
researchers around the globe are working to enhance this body of
knowledge. In this paper, an attempt has been made to compile the
salient features of this theory from the work done by Goldratt and
other researchers. This paper will provide a good starting point to the
potential researchers interested to work in Theory of Constraints. The
paper will also help the practicing managers by clarifying their
concepts on the theory and will facilitate its successful
implementation in their working areas.
Abstract: Bone remodeling occurs by the balanced action of
bone resorbing osteoclasts (OC) and bone-building osteoblasts.
Increased bone resorption by excessive OC activity contributes
to malignant and non-malignant diseases including osteoporosis.
To study OC differentiation and function, OC formed in
in vitro cultures are currently counted manually, a tedious
procedure which is prone to inter-observer differences. Aiming
for an automated OC-quantification system, classification of
OC and precursor cells was done on fluorescence microscope
images based on the distinct appearance of fluorescent nuclei.
Following ellipse fitting to nuclei, a combination of eight
features enabled clustering of OC and precursor cell nuclei.
After evaluating different machine-learning techniques, LOGREG
achieved 74% correctly classified OC and precursor cell
nuclei, outperforming human experts (best expert: 55%). In
combination with the automated detection of total cell areas,
this system allows to measure various cell parameters and most
importantly to quantify proteins involved in osteoclastogenesis.
Abstract: A new digital transceiver circuit for asynchronous frame detection is proposed where both the transmitter and receiver contain all digital components, thereby avoiding possible use of conventional devices like monostable multivibrators with unstable external components such as resistances and capacitances. The proposed receiver circuit, in particular, uses a combinational logic block yielding an output which changes its state as soon as the start bit of a new frame is detected. This, in turn, helps in generating an efficient receiver sampling clock. A data latching circuit is also used in the receiver to latch the recovered data bits in any new frame. The proposed receiver structure is also extended from 4- bit information to any general n data bits within a frame with a common expression for the output of the combinational logic block. Performance of the proposed hardware design is evaluated in terms of time delay, reliability and robustness in comparison with the standard schemes using monostable multivibrators. It is observed from hardware implementation that the proposed circuit achieves almost 33 percent speed up over any conventional circuit.
Abstract: Subdivision is a method to create a smooth surface from a coarse mesh by subdividing the entire mesh. The conventional ways to compute and render surfaces are inconvenient both in terms of memory and computational time as the number of meshes will increase exponentially. An adaptive subdivision is the way to reduce the computational time and memory by subdividing only certain selected areas. In this paper, a new adaptive subdivision method for triangle meshes is introduced. This method defines a new adaptive subdivision rules by considering the properties of each triangle's neighbors and is embedded in a traditional Loop's subdivision. It prevents some undesirable side effects that appear in the conventional adaptive ways. Models that were subdivided by our method are compared with other adaptive subdivision methods
Abstract: This paper presents a unified approach based graph
theory and system theory postulates for the modeling and analysis
of Simple open cycle Gas turbine system. In the present paper, the
simple open cycle gas turbine system has been modeled up to its subsystem
level and system variables have been identified to develop the
process subgraphs. The theorems and algorithms of the graph theory
have been used to represent behavioural properties of the system like
rate of heat and work transfers rates, pressure drops and temperature
drops in the involved processes of the system. The processes have
been represented as edges of the process subgraphs and their limits
as the vertices of the process subgraphs. The system across variables
and through variables has been used to develop terminal equations of
the process subgraphs of the system. The set of equations developed
for vertices and edges of network graph are used to solve the system
for its process variables.
Abstract: In this paper, a new technique for fast painting with
different colors is presented. The idea of painting relies on applying
masks with different colors to the background. Fast painting is
achieved by applying these masks in the frequency domain instead of
spatial (time) domain. New colors can be generated automatically as a
result from the cross correlation operation. This idea was applied
successfully for faster specific data (face, object, pattern, and code)
detection using neural algorithms. Here, instead of performing cross
correlation between the input input data (e.g., image, or a stream of
sequential data) and the weights of neural networks, the cross
correlation is performed between the colored masks and the
background. Furthermore, this approach is developed to reduce the
computation steps required by the painting operation. The principle of
divide and conquer strategy is applied through background
decomposition. Each background is divided into small in size subbackgrounds
and then each sub-background is processed separately by
using a single faster painting algorithm. Moreover, the fastest painting
is achieved by using parallel processing techniques to paint the
resulting sub-backgrounds using the same number of faster painting
algorithms. In contrast to using only faster painting algorithm, the
speed up ratio is increased with the size of the background when using
faster painting algorithm and background decomposition. Simulation
results show that painting in the frequency domain is faster than that in
the spatial domain.
Abstract: The aim of this work was to investigate the potential of soil microorganisms and the burhead plant, as well as the combination of soil microorganisms and plants to remediate monoethylene glycol (MEG), diethylene glycol (DEG), and triethylene glycol (TEG) in synthetic wastewater. The result showed that a system containing both burhead plant and soil microorganisms had the highest efficiency in EGs removal. Around 100% of MEG and DEG and 85% of TEG were removed within 15 days of the experiments. However, the burhead plant had higher removal efficiency than soil microorganisms for MEG and DEG but the same for TEG in the study systems. The removal rate of EGs in the study system related to the molecular weight of the compounds and MEG, the smallest glycol, was removed faster than DEG and TEG by both the burhead plant and soil microorganisms in the study system.
Abstract: This paper is mainly concerned with the application of a novel technique of data interpretation to the characterization and classification of measurements of plasma columns in Tokamak reactors for nuclear fusion applications. The proposed method exploits several concepts derived from soft computing theory. In particular, Artifical Neural Networks have been exploited to classify magnetic variables useful to determine shape and position of the plasma with a reduced computational complexity. The proposed technique is used to analyze simulated databases of plasma equilibria based on ITER geometry configuration. As well as demonstrating the successful recovery of scalar equilibrium parameters, we show that the technique can yield practical advantages compares with earlier methods.
Abstract: Distributed Generation (DG) in the form of renewable
power generation systems is currently preferred for clean power
generation. It has a significant impact on the distribution systems.
This impact may be either positively or negatively depending on the
distribution system, distributed generator and load characteristics. In
this works, an overview of DG is briefly introduced. The technology
of DG is also listed while the technical impacts and economic
impacts are explained.
Abstract: The present paper proposes high performance nonlinear
force controllers for a servopneumatic real-time fatigue test
machine. A CompactRIO® controller was used, being fully
programmed using LabVIEW language. Fuzzy logic control
algorithms were evaluated to tune the integral and derivative
components in the development of hybrid controllers, namely a FLC
P and a hybrid FLC PID real-time-based controllers. Their
behaviours were described by using state diagrams. The main
contribution is to ensure a smooth transition between control states,
avoiding discrete transitions in controller outputs. Steady-state errors
lower than 1.5 N were reached, without retuning the controllers.
Good results were also obtained for sinusoidal tracking tasks from
1/¤Ç to 8/¤Ç Hz.
Abstract: Modern organizations operate under the pressure of
dynamic and often unpredictable changes, both in external and
internal environment. Market success, in this context, requires a
particular competence in the form of flexibility, interpreted here both
on the level of individuals and on the level of organization. This
paper addresses the changes taking place in the sphere of
employment, as observed in economic entities operating on Polish
market. Based on own empirical studies, the authors focus on the
progressing trend of ‘flexibilization’ of employment, particularly in
the context of transformations in organizational structure, designed to
facilitate the transition into management by projects and
differentiation of labor forms.
Abstract: Artificial Neural Network (ANN) has been
extensively used for classification of heart sounds for its
discriminative training ability and easy implementation. However, it
suffers from overparameterization if the number of nodes is not
chosen properly. In such cases, when the dataset has redundancy
within it, ANN is trained along with this redundant information that
results in poor validation. Also a larger network means more
computational expense resulting more hardware and time related
cost. Therefore, an optimum design of neural network is needed
towards real-time detection of pathological patterns, if any from heart
sound signal. The aims of this work are to (i) select a set of input
features that are effective for identification of heart sound signals and
(ii) make certain optimum selection of nodes in the hidden layer for a
more effective ANN structure. Here, we present an optimization
technique that involves Singular Value Decomposition (SVD) and
QR factorization with column pivoting (QRcp) methodology to
optimize empirically chosen over-parameterized ANN structure.
Input nodes present in ANN structure is optimized by SVD followed
by QRcp while only SVD is required to prune undesirable hidden
nodes. The result is presented for classifying 12 common
pathological cases and normal heart sound.
Abstract: A finite element analysis (FEA) computer software HyperWorks is utilized in re-designing an automotive component to reduce its mass. Reduction of components mass contributes towards environmental sustainability by saving world-s valuable metal resources and by reducing carbon emission through improved overall vehicle fuel efficiency. A shape optimization analysis was performed on a rear spindle component. Pre-processing and solving procedures were performed using HyperMesh and RADIOSS respectively. Shape variables were defined using HyperMorph. Then optimization solver OptiStruct was utilized with fatigue life set as a design constraint. Since Stress-Number of Cycle (S-N) theory deals with uni-axial stress, the Signed von Misses stress on the component was used for looking up damage on S-N curve, and Gerber criterion for mean stress corrections. The optimization analysis resulted in mass reduction of 24% of the original mass. The study proved that the adopted approach has high potential use for environmental sustainability.