Abstract: One of the mayor problems of programming a cruise
circuit is to decide which destinations to include and which don-t.
Thus a decision problem emerges, that might be solved using a linear
and goal programming approach. The problem becomes more
complex if several boats in the fleet must be programmed in a limited
schedule, trying their capacity matches best a seasonal demand and
also attempting to minimize the operation costs. Moreover, the
programmer of the company should consider the time of the
passenger as a limited asset, and would like to maximize its usage.
The aim of this work is to design a method in which, using linear and
goal programming techniques, a model to design circuits for the
cruise company decision maker can achieve an optimal solution
within the fleet schedule.
Abstract: In this era of globalization, the role of the State in all aspects of development is widely debated. Some scholars contend the 'demise' and diminishing role of the State whilst others claim that the State is still “de facto developmental". Clearly, it is vital to ascertain which of these two contentions are reflective of the role of the State as nations ascend their development trajectories. Based on the findings of this paper, the perception that the Malaysian State plays an active and committed role towards distributing equitable educational opportunities and enhancing employability of Malaysian PWDs is actually a myth and not reality. Thus, in order to fulfill the promise of Vision 2020 to transform Malaysia into a caring and socially-inclusive society; this paper calls for a more interventionist and committed role by the Malaysian State to translate the universal rights of education and employment opportunities for PWDs from mere policy rhetoric into inclusive realities.
Abstract: A simple approach is demonstrated for growing large
scale, nearly vertically aligned ZnO nanowire arrays by thermal
oxidation method. To reveal effect of temperature on growth and
physical properties of the ZnO nanowires, gold coated zinc substrates
were annealed at 300 °C and 400 °C for 4 hours duration in air. Xray
diffraction patterns of annealed samples indicated a set of well
defined diffraction peaks, indexed to the wurtzite hexagonal phase of
ZnO. The scanning electron microscopy studies show formation of
ZnO nanowires having length of several microns and average of
diameter less than 500 nm. It is found that the areal density of wires
is relatively higher, when the annealing is carried out at higher
temperature i.e. at 400°C. From the field emission studies, the values
of the turn-on and threshold field, required to draw emission current
density of 10 μA/cm2 and 100 μA/cm2 are observed to be 1.2 V/μm
and 1.7 V/μm for the samples annealed at 300 °C and 2.9 V/μm and
3.7 V/μm for that annealed at 400 °C, respectively. The field
emission current stability, investigated over duration of more than 2
hours at the preset value of 1 μA, is found to be fairly good in both
cases. The simplicity of the synthesis route coupled with the
promising field emission properties offer unprecedented advantage
for the use of ZnO field emitters for high current density
applications.
Abstract: In this paper, we define permutable and mutually permutable fuzzy subgroups of a group. Then we study their relation with permutable and mutually permutable subgroups of a group. Also we study some properties of fuzzy quasinormal subgroup. We define superfuzzy subset of a fuzzy subset and we study some properties of superfuzzy subset of a fuzzy subset.
Abstract: This paper considers inference under progressive type II censoring with a compound Rayleigh failure time distribution. The maximum likelihood (ML), and Bayes methods are used for estimating the unknown parameters as well as some lifetime parameters, namely reliability and hazard functions. We obtained Bayes estimators using the conjugate priors for two shape and scale parameters. When the two parameters are unknown, the closed-form expressions of the Bayes estimators cannot be obtained. We use Lindley.s approximation to compute the Bayes estimates. Another Bayes estimator has been obtained based on continuous-discrete joint prior for the unknown parameters. An example with the real data is discussed to illustrate the proposed method. Finally, we made comparisons between these estimators and the maximum likelihood estimators using a Monte Carlo simulation study.
Abstract: Medical applications are among the most impactful
areas of microrobotics. The ultimate goal of medical microrobots is
to reach currently inaccessible areas of the human body and carry out
a host of complex operations such as minimally invasive surgery
(MIS), highly localized drug delivery, and screening for diseases at
their very early stages. Miniature, safe and efficient propulsion
systems hold the key to maturing this technology but they pose
significant challenges. A new type of propulsion developed recently,
uses multi-flagella architecture inspired by the motility mechanism of
prokaryotic microorganisms. There is a lack of efficient methods for
designing this type of propulsion system. The goal of this paper is to
overcome the lack and this way, a numerical strategy is proposed to
design multi-flagella propulsion systems. The strategy is based on the
implementation of the regularized stokeslet and rotlet theory, RFT
theory and new approach of “local corrected velocity". The effects of
shape parameters and angular velocities of each flagellum on overall
flow field and on the robot net forces and moments are considered.
Then a multi-layer perceptron artificial neural network is designed
and employed to adjust the angular velocities of the motors for
propulsion control. The proposed method applied successfully on a
sample configuration and useful demonstrative results is obtained.
Abstract: Fault tree analysis is a well-known method for
reliability and safety assessment of engineering systems. In the last 3
decades, a number of methods have been introduced, in the literature,
for automatic construction of fault trees. The main difference between these methods is the starting model from which the tree is constructed. This paper presents a new methodology for the construction of static and dynamic fault trees from a system Simulink
model. The method is introduced and explained in detail, and its correctness and completeness is experimentally validated by using an example, taken from literature. Advantages of the method are also mentioned.
Abstract: Speeded-Up Robust Feature (SURF) is commonly used for feature matching in stereovision because of their robustness towards scale changes and rotational changes. However, SURF feature cannot cope with large viewpoint changes or skew distortion. This paper introduces a method which can help to improve the wide baseline-s matching performance in term of accuracy by rectifying the image using two vanishing points. Simplified orientation correction was used to remove the false matching..
Abstract: Cylindrical concrete reservoirs are appropriate choice
for storing liquids as water, oil and etc. By using of the pre-cast
concrete reservoirs instead of the in-situ constructed reservoirs, the
speed and precision of the construction would considerably increase.
In this construction method, wall and roof panels would make in
factory with high quality materials and precise controlling. Then,
pre-cast wall and roof panels would carry out to the construction site
for assembling. This method has a few faults such as: the existing
weeks in connection of wall panels together and wall panels to
foundation. Therefore, these have to be resisted under applied loads
such as seismic load. One of the innovative methods which was
successfully applied for seismic retrofitting of numerous pre-cast
cylindrical water reservoirs in New Zealand, using of the high tensile
cables around the reservoirs and post-tensioning them. In this paper,
analytical modeling of wall and roof panels and post-tensioned
cables are carried out with finite element method and the effect of
height to diameter ratio, post-tensioning force value, liquid level in
reservoir, installing position of tendons on seismic response of
reservoirs are investigated.
Abstract: Probability-based identity disclosure risk
measurement may give the same overall risk for different
anonymization strategy of the same dataset. Some entities in the
anonymous dataset may have higher identification risks than the
others. Individuals are more concerned about higher risks than the
average and are more interested to know if they have a possibility of
being under higher risk. A notation of overall risk in the above
measurement method doesn-t indicate whether some of the involved
entities have higher identity disclosure risk than the others. In this
paper, we have introduced an identity disclosure risk measurement
method that not only implies overall risk, but also indicates whether
some of the members have higher risk than the others. The proposed
method quantifies the overall risk based on the individual risk values,
the percentage of the records that have a risk value higher than the
average and how larger the higher risk values are compared to the
average. We have analyzed the disclosure risks for different
disclosure control techniques applied to original microdata and
present the results.
Abstract: In this research, the flow pattern influence on
performance of a micro PEMFC was investigated
experimentally. The investigation focused on the impacts of
bend angels and rib/channel dimensions of serpentine flow
channel pattern on the performance and investigated how they
improve the performance. The fuel cell employed for these
experiments was a micro single PEMFC with a membrane of
1.44 cm2 Nafion NRE-212. The results show that 60° and 120°
bend angles can provide the better performances at 20 and 40
sccm inlet flow rates comparing to that the conventional design.
Additionally, wider channel with narrower rib spacing gives
better performance. These results may be applied to develop
universal heuristics for the design of flow pattern of micro
PEMFC.
Abstract: In this research, we have developed a new efficient
heuristic algorithm for the dynamic facility layout problem with
budget constraint (DFLPB). This heuristic algorithm combines two
mathematical programming methods such as discrete event
simulation and linear integer programming (IP) to obtain a near
optimum solution. In the proposed algorithm, the non-linear model
of the DFLP has been changed to a pure integer programming (PIP)
model. Then, the optimal solution of the PIP model has been used in
a simulation model that has been designed in a similar manner as the
DFLP for determining the probability of assigning a facility to a
location. After a sufficient number of runs, the simulation model
obtains near optimum solutions. Finally, to verify the performance of
the algorithm, several test problems have been solved. The results
show that the proposed algorithm is more efficient in terms of speed
and accuracy than other heuristic algorithms presented in previous
works found in the literature.
Abstract: This paper proposes an easy-to-use instruction hiding
method to protect software from malicious reverse engineering
attacks. Given a source program (original) to be protected, the
proposed method (1) takes its modified version (fake) as an input,
(2) differences in assembly code instructions between original and
fake are analyzed, and, (3) self-modification routines are introduced
so that fake instructions become correct (i.e., original instructions)
before they are executed and that they go back to fake ones after
they are executed. The proposed method can add a certain amount
of security to a program since the fake instructions in the resultant
program confuse attackers and it requires significant effort to discover
and remove all the fake instructions and self-modification routines.
Also, this method is easy to use (with little effort) because all a user
(who uses the proposed method) has to do is to prepare a fake source
code by modifying the original source code.
Abstract: Axisymmetric vibration of an infinite Pyrocomposite
circular hollow cylinder made of inner and outer pyroelectric layer of
6mm-class bonded together by a Linear Elastic Material with Voids
(LEMV) layer is studied. The exact frequency equation is obtained
for the traction free surfaces with continuity condition at the
interfaces. Numerical results in the form of data and dispersion
curves for the first and second mode of the axisymmetric vibration of
the cylinder BaTio3 / Adhesive / BaTio3 by taking the Adhesive layer
as an existing Carbon Fibre Reinforced Polymer (CFRP) are
compared with a hypothetical LEMV layer with and without voids
and as well with a pyroelectric hollow cylinder. The damping is
analyzed through the imaginary parts of the complex frequencies.
Abstract: The genre of fantasy depicts a world of imagine that triggers popular interest from a created view of world, and a fantasy is defined as a story that illustrates a world of imagine where scientific or horror elements are stand in its center. This study is not focused on the narrative of the fantasy, i.e. not on the adventurous story, but is concentrated on the image of the fantasy to work on its relationship with intended themes and differences among cultures due to meanings of materials. As for films, we have selected some films in the 2000's that are internationally recognized as expressing unique images of fantasy containing the theme of love in them. The selected films are 5 pieces including two European films, Amelie from Montmartre (2001) and The Science of Sleep (2005) and three Asian films, Citizen Dog from Thailand (2004), Memories of Matsuko from Japan (2006), and I'm a Cyborg, but That's OK from Korea (2006). These films share some common characteristics to the effect that they give tiny lessons and feelings for life with expressions of fantasy images as if they were fairy tales for adults and that they lead the audience to reflect on their days and revive forgotten dreams of childhood. We analyze the images of fantasy in each of the films on the basis of the elements of Mise-en-Scène (setting and props, costume, hair and make-up, facial expressions and body language, lighting and color, positioning of characters, and objects within a frame).
Abstract: In this paper, a two-channel secure communication
using fractional chaotic systems is presented. Conditions for chaos
synchronization have been investigated theoretically by using Laplace
transform. To illustrate the effectiveness of the proposed scheme, a
numerical example is presented. The keys, key space, key selection
rules and sensitivity to keys are discussed in detail. Results show that
the original plaintexts have been well masked in the ciphertexts yet
recovered faithfully and efficiently by the present schemes.
Abstract: This work aims to reduce the read power consumption
as well as to enhance the stability of the SRAM cell during the read
operation. A new 10-transisor cell is proposed with a new read
scheme to minimize the power consumption within the memory core.
It has separate read and write ports, thus cell read stability is
significantly improved. A 16Kb SRAM macro operating at 1V
supply voltage is demonstrated in 65 nm CMOS process. Its read
power consumption is reduced to 24% of the conventional design.
The new cell also has lower leakage current due to its special bit-line
pre-charge scheme. As a result, it is suitable for low-power mobile
applications where power supply is restricted by the battery.
Abstract: A high precision temperature insensitive current and voltage reference generator is presented. It is specifically developed for temperature compensated oscillator. The circuit, designed using MXIC 0.5um CMOS technology, has an operating voltage that ranges from 2.6V to 5V and generates a voltage of 1.21V and a current of 6.38 ӴA. It exhibits a variation of ±0.3nA for the current reference and a stable output for voltage reference as the temperature is varied from 0°C to 70°C. The power supply rejection ratio obtained without any filtering capacitor at 100Hz and 10MHz is -30dB and -12dB respectively.
Abstract: The purpose of this paper primarily intends to develop GIS interface for estimating sequences of stream-flows at ungauged stations based on known flows at gauged stations. The integrated GIS interface is composed of three major steps. The first, precipitation characteristics using statistical analysis is the procedure for making multiple linear regression equation to get the long term mean daily flow at ungauged stations. The independent variables in regression equation are mean daily flow and drainage area. Traditionally, mean flow data are generated by using Thissen polygon method. However, method for obtaining mean flow data can be selected by user such as Kriging, IDW (Inverse Distance Weighted), Spline methods as well as other traditional methods. At the second, flow duration curve (FDC) is computing at unguaged station by FDCs in gauged stations. Finally, the mean annual daily flow is computed by spatial interpolation algorithm. The third step is to obtain watershed/topographic characteristics. They are the most important factors which govern stream-flows. In summary, the simulated daily flow time series are compared with observed times series. The results using integrated GIS interface are closely similar and are well fitted each other. Also, the relationship between the topographic/watershed characteristics and stream flow time series is highly correlated.
Abstract: Computer based geostatistical methods can offer effective data analysis possibilities for agricultural areas by using
vectorial data and their objective informations. These methods will help to detect the spatial changes on different locations of the large
agricultural lands, which will lead to effective fertilization for optimal yield with reduced environmental pollution. In this study, topsoil (0-20 cm) and subsoil (20-40 cm) samples were taken from a
sugar beet field by 20 x 20 m grids. Plant samples were also collected
from the same plots. Some physical and chemical analyses for these
samples were made by routine methods. According to derived variation coefficients, topsoil organic matter (OM) distribution was more than subsoil OM distribution. The highest C.V. value of
17.79% was found for topsoil OM. The data were analyzed
comparatively according to kriging methods which are also used
widely in geostatistic. Several interpolation methods (Ordinary,Simple and Universal) and semivariogram models (Spherical,
Exponential and Gaussian) were tested in order to choose the suitable
methods. Average standard deviations of values estimated by simple
kriging interpolation method were less than average standard
deviations (topsoil OM ± 0.48, N ± 0.37, subsoil OM ± 0.18) of measured values. The most suitable interpolation method was simple
kriging method and exponantial semivariogram model for topsoil,
whereas the best optimal interpolation method was simple kriging
method and spherical semivariogram model for subsoil. The results
also showed that these computer based geostatistical methods should
be tested and calibrated for different experimental conditions and semivariogram models.