Abstract: This paper presents a novel CMOS four-transistor
SRAM cell for very high density and low power embedded SRAM
applications as well as for stand-alone SRAM applications. This cell
retains its data with leakage current and positive feedback without
refresh cycle. The new cell size is 20% smaller than a conventional
six-transistor cell using same design rules. Also proposed cell uses
two word-lines and one pair bit-line. Read operation perform from
one side of cell, and write operation perform from another side of
cell, and swing voltage reduced on word-lines thus dynamic power
during read/write operation reduced. The fabrication process is fully
compatible with high-performance CMOS logic technologies,
because there is no need to integrate a poly-Si resistor or a TFT load.
HSPICE simulation in standard 0.25μm CMOS technology confirms
all results obtained from this paper.
Abstract: Metallic micro parts are playing an important role in micro-fabrication industry. Recently, we have demonstrated a new deformation mechanism for micro-formability of polycrystalline materials. Different depressed micro-features smaller than the grain size have been successfully fabricated on 6061 aluminum alloy (AA6061) substrates with good fidelity. To further verify this proposed deformation mechanism that grain size is not a limiting factor, we demonstrate here that in addition of depressed features, protruded micro-features on a polycrystalline substrate can similarly be fabricated.
Abstract: The operation performance of a valveless micro-pump
is strongly dependent on the shape of connected nozzle/diffuser and
Reynolds number. The aims of present work are to compare the
performance curves of micropump with the original straight
nozzle/diffuser and contoured nozzle/diffuser under different back
pressure conditions. The tested valveless micropumps are assembled
of five pieces of patterned PMMA plates with hot-embracing
technique. The structures of central chamber, the inlet/outlet
reservoirs and the connected nozzle/diffuser are fabricated with laser
cutting machine. The micropump is actuated with circular-type PZT
film embraced on the bottom of central chamber. The deformation of
PZT membrane with various input voltages is measured with a
displacement laser probe. A simple testing facility is also constructed
to evaluate the performance curves for comparison.
In order to observe the evaluation of low Reynolds number
multiple vortex flow patterns within the micropump during suction
and pumping modes, the unsteady, incompressible laminar
three-dimensional Reynolds-averaged Navier-Stokes equations are
solved. The working fluid is DI water with constant thermo-physical
properties. The oscillating behavior of PZT film is modeled with the
moving boundary wall in way of UDF program. With the dynamic
mesh method, the instants pressure and velocity fields are obtained
and discussed.Results indicated that the volume flow rate is not
monotony increased with the oscillating frequency of PZT film,
regardless of the shapes of nozzle/diffuser. The present micropump
can generate the maximum volume flow rate of 13.53 ml/min when
the operation frequency is 64Hz and the input voltage is 140 volts.
The micropump with contoured nozzle/diffuser can provide 7ml/min
flow rate even when the back pressure is up to 400 mm-H2O. CFD
results revealed that the flow central chamber was occupied with
multiple pairs of counter-rotating vortices during suction and
pumping modes. The net volume flow rate over a complete
oscillating periodic of PZT
Abstract: An active RC filters with a 880 / 1760 MHz dual bandwidth tuning ability is present for 60 GHz unlicensed band applications. A third order Butterworth low-pass filter utilizes two Cherry-Hooper amplifiers to satisfy the very high bandwidth requirements of an amplifier. The low-pass filter is fabricated in 90nm standard CMOS process. Drawing 6.7 mW from 1.2 V power supply, the low frequency gains of the filter are -2.5 and -4.1 dB, and the output third order intercept points (OIP3) are +2.2 and +1.9 dBm for the single channel and channel bonding conditions, respectively.
Abstract: In a nuclear reactor Loss of Coolant accident (LOCA)
considers wide range of postulated damage or rupture of pipe in the
heat transport piping system. In the case of LOCA with/without
failure of emergency core cooling system in a Pressurised Heavy
water Reactor, the Pressure Tube (PT) temperature could rise
significantly due to fuel heat up and gross mismatch of the heat
generation and heat removal in the affected channel. The extent and
nature of deformation is important from reactor safety point of view.
Experimental set-ups have been designed and fabricated to simulate
ballooning (radial deformation) of PT for 220 MWe IPHWRs.
Experiments have been conducted by covering the CT by ceramic
fibers and then by submerging CT in water of voided PTs. In both
the experiments, it is observed that ballooning initiates at a
temperature around 665´┐¢C and complete contact between PT and
Caldaria Tube (CT) occurs at around 700´┐¢C approximately. The
strain rate is found to be 0.116% per second. The structural integrity
of PT is retained (no breach) for all the experiments. The PT heatup
is found to be arrested after the contact between PT and CT, thus
establishing moderator acting as an efficient heat sink for IPHWRs.
Abstract: The use of hard and brittle material has become
increasingly more extensive in recent years. Therefore processing of
these materials for the parts fabrication has become a challenging
problem. However, it is time-consuming to machine the hard brittle
materials with the traditional metal-cutting technique that uses
abrasive wheels. In addition, the tool would suffer excessive wear as
well. However, if ultrasonic energy is applied to the machining
process and coupled with the use of hard abrasive grits, hard and
brittle materials can be effectively machined. Ultrasonic machining
process is mostly used for the brittle materials. The present research
work has developed models using finite element approach to predict
the mechanical stresses sand strains produced in the tool during
ultrasonic machining process. Also the flow behavior of abrasive
slurry coming out of the nozzle has been studied for simulation using
ANSYS CFX module. The different abrasives of different grit sizes
have been used for the experimentation work.
Abstract: The biomarker for colorectal cancer (CRC) is CEACAM-6 antigen (C6AG). Therefore, this study aims to develop a novel, simple and low-cost CEACAM-6 antigen immumosensor (C6AG-IMS), based on electrical impedance measurement, for precise determination of C6AG. A low-cost screen-printed graphite electrode was constructed and used as the sensor, with CEACAM-6 antibody (C6AB) immobilized on it. The procedures of sensor fabrication and antibody immobilization are simple and low-cost. Measurement of the electrical impedance at a definite frequency ranges (0.43 – 1.26 MHz) showed that the C6AG-IMS has an excellent linear (r2>0.9) response range (8.125 – 65 pg/mL), covering the normal physiological and pathological ranges of blood C6AG levels. Also, the C6AG-IMS has excellent reliability and validity, with the intraclass correlation coefficient being 0.97. In conclusion, a novel, simple, low-cost and reliable C6AG-IMS was designed and developed, being able to accurately determine blood C6AG levels in the range of pathological and normal physiological regions. The C6AG-IMS can provide a point-of-care and immediate screening results to the user at home.
Abstract: In the present study, fracture behavior of woven
fabric-reinforced glass/epoxy composite laminates under mode III
crack growth was experimentally investigated and numerically
modeled. Two methods were used for the calculation of the strain
energy release rate: the experimental compliance calibration (CC)
method and the Virtual Crack Closure Technique (VCCT). To
achieve this aim ECT (Edge Crack Torsion) was used to evaluate
fracture toughness in mode III loading (out of plane-shear) at
different crack lengths. Load–displacement and associated energy
release rates were obtained for various case of interest. To
calculate fracture toughness JIII, two criteria were considered
including non-linearity and maximum points in load-displacement
curve and it is observed that JIII increases with the crack length
increase. Both the experimental compliance method and the virtual
crack closure technique proved applicable for the interpretation of the
fracture mechanics data of woven glass/epoxy laminates in mode III.
Abstract: The autonomous mobile robot was designed and implemented which was capable of navigating in the industrial environments and did a job of picking objects from variable height and delivering it to another location following a predefined trajectory. In developing country like Bangladesh industrial robotics is not very prevalent yet, due to the high installation cost. The objective of this project was to develop an autonomous mobile robot for industrial application using the available resources in the local market at lower manufacturing cost. The mechanical system of the robot was comprised of locomotion, gripping and elevation system. Grippers were designed to grip objects of a predefined shape. Cartesian elevation system was designed for vertical movement of the gripper. PIC18F452 microcontroller was the brain of the control system. The prototype autonomous robot was fabricated for relatively lower load than the industry and the performance was tested in a virtual industrial environment created within the laboratory to realize the effectiveness.
Abstract: Microstrip antennas are conformable to planar and
nonplanar surfaces, simple and inexpensive to fabricate using modern
printed-circuit technology. Circular polarization of low-profile
microstrip patch with high bandwidth is achieved in this research
through the use of a three-cross-arms branch-line coupler with
sequential rotated arrays, another low-profile antenna of hollow
cylinder is also proposed and the function of reconnaissance with
microstrip antenna on Mini UAV (unmanned aerial vehicle) are
evaluated in practical flight test.
Abstract: In the present work homogeneous silica film on
silicon was fabricated by colloidal silica sol. The silica sol precursor
with uniformly granular particle was derived by the alkaline
hydrolysis of tetraethoxyorthosilicate (TEOS) in presence of glycerol
template. The film was prepared by dip coating process. The
templated hetero-structured silica film was annealed at elevated
temperatures to generate nano- and meso porosity in the film. The
film was subsequently annealed at different temperatures to make it
defect free and abrasion resistant. The sol and the film were
characterized by the measurement of particle size distribution,
scanning electron microscopy, XRD, FTIR spectroscopy,
transmission electron microscopy, atomic force microscopy,
measurement of the refractive index, thermal conductivity and
abrasion resistance. The porosity of the films decreased whereas
refractive index and dielectric constant of it `increased with the
increase in the annealing temperature. The thermal conductivity of
the films increased with the increase in the film thickness. The
developed porous silica film holds strong potential for use in
different areas.
Abstract: With respect to the dissipation of energy through
plastic deformation of joints of prefabricated wall units, the paper
points out the principal importance of efficient reinforcement of the
prefabricated system at its joints. The method, quality and amount of
reinforcement are essential for reaching the necessary degree of joint
ductility. The paper presents partial results of experimental research
of vertical joints of prefabricated units exposed to monotonously
rising loading and repetitive shear force and formulates a conclusion
that the limit state of the structure as a whole is preceded by the
disintegration of joints, or that the structure tends to pass from
linearly elastic behaviour to non-linearly elastic to plastic behaviour
by exceeding the proportional elastic limit in joints.Experimental
verification on a model of a 7-storey prefabricated structure revealed
weak points in its load-bearing systems, mainly at places of critical
points around openings situated in close proximity to vertical joints
of mutually perpendicularly oriented walls.
Abstract: This paper investigates experimental studies on
vibration suppression for a cantilever beam using an
Electro-Rheological (ER) sandwich shock absorber. ER fluid (ERF) is a
class of smart materials that can undergo significant reversible changes
immediately in its rheological and mechanical properties under the
influence of an applied electric field. Firstly, an ER sandwich beam is
fabricated by inserting a starch-based ERF into a hollow composite
beam. At the same time, experimental investigations are focused on the
frequency response of the ERF sandwich beam. Second, the ERF
sandwich beam is attached to a cantilever beam to become as a shock
absorber. Finally, a fuzzy semi-active vibration control is designed to
suppress the vibration of the cantilever beam via the ERF sandwich
shock absorber. To check the consistency of the proposed fuzzy
controller, the real-time implementation validated the performance of
the controller.
Abstract: Oxidative stress makes up common incidents in
eukaryotic metabolism. The presence of diverse components
disturbing the equilibrium during oxygen metabolism increases
oxidative damage unspecifically in living cells. Body´s own
ubiquinone (Q10) seems to be a promising drug in defending the
heightened appearance of reactive oxygen species (ROS). Though, its
lipophilic properties require a new strategy in drug formulation to
overcome their low bioavailability. Consequently, the manufacture of
heterogeneous nanodispersions is in focus for medical applications.
The composition of conventional nanodispersions is made up of a
drug-consisting core and a surfactive agent, also named as surfactant.
Long-termed encapsulation of the surfactive components into tissues
might be the consequence of the use during medical therapeutics. The
potential of provoking side-effects is given by their nonbiodegradable
properties. Further improvements during fabrication
process use the incorporation of biodegradable components such as
modified γ-polyglutamic acid which decreases the potential of
prospective side-effects.
Abstract: The demand for higher performance graphics
continues to grow because of the incessant desire towards realism.
And, rapid advances in fabrication technology have enabled us to
build several processor cores on a single die. Hence, it is important to
develop single chip parallel architectures for such data-intensive
applications. In this paper, we propose an efficient PIM architectures
tailored for computer graphics which requires a large number of
memory accesses. We then address the two important tasks necessary
for maximally exploiting the parallelism provided by the architecture,
namely, partitioning and placement of graphic data, which affect
respectively load balances and communication costs. Under the
constraints of uniform partitioning, we develop approaches for optimal
partitioning and placement, which significantly reduce search space.
We also present heuristics for identifying near-optimal placement,
since the search space for placement is impractically large despite our
optimization. We then demonstrate the effectiveness of our partitioning
and placement approaches via analysis of example scenes; simulation
results show considerable search space reductions, and our heuristics
for placement performs close to optimal – the average ratio of
communication overheads between our heuristics and the optimal was
1.05. Our uniform partitioning showed average load-balance ratio of
1.47 for geometry processing and 1.44 for rasterization, which is
reasonable.
Abstract: We focus on the excitation and propagation properties
of surface plasmon polariton (SPP). We have developed a SPP
excitation device in combination with a grating structures fabricated
by using the scanning probe lithography. Perturbation approach was
used to investigate the coupling properties of SPP with a spatial
harmonic wave supported by a metallic grating. A phase shift grating
SPP coupler has been fabricated and the optical property was
evaluated by the Fraunhofer diffraction formula. We have been
experimentally confirmed the induced stop band by diffraction
measurement. We have also observed the wavenumber shift of the
resonance condition of SPP owing to effect of a phase shift.
Abstract: There are several means to measure the oxidation of edible oils, such as the acid value, the peroxide value, and the anisidine value. However, these means require large quantities of reagents and are time-consuming tasks. Therefore, a more convenient and time-saving way to measure the oxidation of edible oils is required. In this report, an edible oil condition sensor was fabricated by using single-walled nanotubes (SWNT). In order to test the sensor, oxidized edible oils, each one at a different acid value, were prepared. The SWNT sensors were immersed into these oxidized oils and the resistance changes in the sensors were measured. It was found that the conductivity of the sensors decreased as the oxidation level of oil increased. This result suggests that a change of the oil components induced by the oxidation process in edible oils is related to the conductivity change in the SWNT sensor.
Abstract: Delamination between layers in composite materials is a major structural failure. The delamination resistance is quantified by the critical strain energy release rate (SERR). The present investigation deals with the strain energy release rate of two woven fabric composites. Materials used are made of two types of glass fiber (360 gsm and 600 gsm) of plain weave and epoxy as matrix. The fracture behavior is studied using the mode I, double cantilever beam test and the mode II, end notched flexure test, in order to determine the energy required for the initiation and growth of an artificial crack. The delamination energy of these two materials is compared in order to study the effect of weave and reinforcement on mechanical properties. The fracture mechanism is also analyzed by means of scanning electron microscopy (SEM). It is observed that the plain weave fabric composite with lesser strand width has higher inter laminar fracture properties compared to the plain weave fabric composite with more strand width.
Abstract: This paper presents the development of low cost Nano membrane fabrication system. The system is specially designed for anodic aluminum oxide membrane. This system is capable to perform the processes such as anodization and electro-polishing. The designed machine was successfully tested for 'mild anodization' (MA) for 48 hours and 'hard anodization' (HA) for 3 hours at constant 0oC. The system is digitally controlled and guided for temperature maintenance during anodization and electro-polishing. The total cost of the developed machine is 20 times less than the multi-cooling systems available in the market which are generally used for this purpose.
Abstract: In this study the elastic-plastic stress distribution in
weld-bonded joint, fabricated from austenitic stainless steel (AISI
304) sheet of 1.00 mm thickness and Epoxy adhesive Araldite 2011,
subjected to axial loading is investigated. This is needed to improve
design procedures and welding codes, and saving efforts in the
cumbersome experiments and analysis. Therefore, a complete 3-D
finite element modelling and analysis of spot welded, bonded and
weld-bonded joints under axial loading conditions is carried out. A
comprehensive systematic experimental program is conducted to
determine many properties and quantities, of the base metals and the
adhesive, needed for FE modelling, such like the elastic – plastic
properties, modulus of elasticity, fracture limit, the nugget and heat
affected zones (HAZ) properties, etc. Consequently, the finite
element models developed, for each case, are used to evaluate
stresses distributions across the entire joint, in both the elastic and
plastic regions. The stress distribution curves are obtained,
particularly in the elastic regions and found to be consistent and in
excellent agreement with the published data. Furthermore, the
stresses distributions are obtained in the weld-bonded joint and
display the best results with almost uniform smooth distribution
compared to spot and bonded cases. The stress concentration peaks at
the edges of the weld-bonded region, are almost eliminated resulting
in achieving the strongest joint of all processes.