Abstract: In this study, Friction Stir Processing (FSP) a recent grain refinement technique was employed to disperse micron-sized (2 *m) SiCp particles into aluminum alloy AA6063. The feasibility to fabricate bulk composites through FSP was analyzed and experiments were conducted at different traverse speeds and wider volumes of the specimens. Micro structural observation were carried out by employing optical microscopy test of the cross sections in both parallel and perpendicular to the tool traverse direction. Mechanical property including micro hardness was evaluated in detail at various regions on the specimen. The composites had an excellent bonding with aluminum alloy substrate and a significant increase of 30% in the micro hardness value of metal matrix composite (MMC) as to that of the base metal has observed. The observations clearly indicate that SiC particles were uniformly distributed within the aluminum matrix.
Abstract: The stab resistance performance of newly developed
fabric composites composed of hexagonal paper honeycombs, filled
with shear thickening fluid (STF), and woven Kevlar® fabric or
UHMPE was investigated in this study. The STF was prepared by
dispersing submicron SiO2 particles into polyethylene glycol (PEG).
Our results indicate that the STF-Kevlar composite possessed lower
penetration depth than that of neat Kevlar. In other words, the
STF-Kevlar composite can attain the same energy level in
stab-resistance test with fewer layers of Kevlar fabrics than that of the
neat Kevlar fabrics. It also indicates that STF can be used for the
fabrication of flexible body armors and can provide improved
protection against stab threats. We found that the stab resistance of the
STF-Kevlar composite increases with the increase of SiO2
concentration in STF. Moreover, the silica particles functionalized
with silane coupling agent can further improve the stab resistance.
Abstract: This paper reports the fatigue crack growth behaviour
of gas tungsten arc, electron beam and laser beam welded Ti-6Al-4V
titanium alloy. Centre cracked tensile specimens were prepared to
evaluate the fatigue crack growth behaviour. A 100kN servo
hydraulic controlled fatigue testing machine was used under constant
amplitude uniaxial tensile load (stress ratio of 0.1 and frequency of
10 Hz). Crack growth curves were plotted and crack growth
parameters (exponent and intercept) were evaluated. Critical and
threshold stress intensity factor ranges were also evaluated. Fatigue
crack growth behaviour of welds was correlated with mechanical
properties and microstructural characteristics of welds. Of the three
joints, the joint fabricated by laser beam welding exhibited higher
fatigue crack growth resistance due to the presence of fine lamellar
microstructure in the weld metal.
Abstract: Heat pipes are used to control the thermal problem for
electronic cooling. It is especially difficult to dissipate heat to a heat
sink in an environment in space compared to earth. For solving this
problem, in this study, the Poiseuille (Po) number, which is the main
measure of the performance of a heat pipe, is studied by CFD; then, the
heat pipe performance is verified with experimental results. A heat
pipe is then fabricated for a spatial environment, and an in-house code
is developed. Further, a heat pipe subsystem, which consists of a heat
pipe, MLI (Multi Layer Insulator), SSM (Second Surface Mirror), and
radiator, is tested and correlated with the TMM (Thermal
Mathematical Model) through a commercial code. The correlation
results satisfy the 3K requirement, and the generated thermal model is
verified for application to a spatial environment.
Abstract: This work describes the aerodynamic characteristic for
aircraft wing model with and without bird feather like winglet. The
aerofoil used to construct the whole structure is NACA 653-218
Rectangular wing and this aerofoil has been used to compare the
result with previous research using winglet. The model of the
rectangular wing with bird feather like winglet has been fabricated
using polystyrene before design using CATIA P3 V5R13 software
and finally fabricated in wood. The experimental analysis for the
aerodynamic characteristic for rectangular wing without winglet,
wing with horizontal winglet and wing with 60 degree inclination
winglet for Reynolds number 1.66×105, 2.08×105 and 2.50×105 have
been carried out in open loop low speed wind tunnel at the
Aerodynamics laboratory in Universiti Putra Malaysia. The
experimental result shows 25-30 % reduction in drag coefficient and
10-20 % increase in lift coefficient by using bird feather like winglet
for angle of attack of 8 degree.
Abstract: The more recent satellite projects/programs makes
extensive usage of real – time embedded systems. 16 bit processors
which meet the Mil-Std-1750 standard architecture have been used in
on-board systems. Most of the Space Applications have been written
in ADA. From a futuristic point of view, 32 bit/ 64 bit processors are
needed in the area of spacecraft computing and therefore an effort is
desirable in the study and survey of 64 bit architectures for space
applications. This will also result in significant technology
development in terms of VLSI and software tools for ADA (as the
legacy code is in ADA).
There are several basic requirements for a special processor for
this purpose. They include Radiation Hardened (RadHard) devices,
very low power dissipation, compatibility with existing operational
systems, scalable architectures for higher computational needs,
reliability, higher memory and I/O bandwidth, predictability, realtime
operating system and manufacturability of such processors.
Further on, these may include selection of FPGA devices, selection
of EDA tool chains, design flow, partitioning of the design, pin
count, performance evaluation, timing analysis etc.
This project deals with a brief study of 32 and 64 bit processors
readily available in the market and designing/ fabricating a 64 bit
RISC processor named RISC MicroProcessor with added
functionalities of an extended double precision floating point unit
and a 32 bit signal processing unit acting as co-processors. In this
paper, we emphasize the ease and importance of using Open Core
(OpenSparc T1 Verilog RTL) and Open “Source" EDA tools such as
Icarus to develop FPGA based prototypes quickly. Commercial tools
such as Xilinx ISE for Synthesis are also used when appropriate.
Abstract: In this paper, multilayered coreless printed circuit
board (PCB) step-down power transformers for DC-DC converter
applications have been designed, manufactured and evaluated. A set
of two different circular spiral step-down transformers were
fabricated in the four layered PCB. These transformers have been
modelled with the assistance of high frequency equivalent circuit and
characterized with both sinusoidal and square wave excitation. This
paper provides the comparative results of these two different
transformers in terms of their resistances, self, leakage, mutual
inductances, coupling coefficient and also their energy efficiencies.
The operating regions for optimal performance of these transformers
for power transfer applications are determined. These transformers
were tested for the output power levels of about 30 Watts within the
input voltage range of 12-50 Vrms. The energy efficiency for these
step down transformers is observed to be in the range of 90%-97% in
MHz frequency region.
Abstract: Design and evaluation of reciprocating compressors
should include a pulsation study. The object is to ensure that
predicted pulsation levels meet guidelines to limit vibration, shaking
forces, noise, associated pressure drops, horsepower losses and
fabrication cost and time to acceptable levels. This paper explains
procedures and recommendations to select and size pulsation
suppression devices to obtain optimum arrangement in terms of
pulsation, vibration, shaking forces, performance, reliability, safety,
operation, maintenance and commercial conditions. Model and
advanced formulations for pulsation study are presented. The effect
of the full fluid dynamic model on the prediction of pulsation waves
and resulting frequency spectrum distributions are discussed.
Advanced and optimum methods of controlling pulsations are
highlighted. Useful recommendations and guidelines for pulsation
control, piping pulsation analysis, pulsation vessel design, shaking
forces, low pressure drop orifices, pulsation study report and devices
to mitigate pulsation and shaking problems are discussed.
Abstract: The aim of study was to evaluate pressure distribution characteristics of the elastic textile bandages using two instrumental techniques: a prototype Instrument and a load Transference. The prototype instrument which simulates shape of real leg has pressure sensors which measure bandage pressure. Using this instrument, the results show that elastic textile bandages presents different pressure distribution characteristics and none produces a uniform distribution around lower limb.
The load transference test procedure is used to determine whether a relationship exists between elastic textile bandage structure and pressure distribution characteristics. The test procedure assesses degree of load, directly transferred through a textile when loads series are applied to bandaging surface. A range of weave fabrics was produced using needle weaving machine and a sewing technique. A textile bandage was developed with optimal characteristics far superior pressure distribution than other bandages. From results, we find that theoretical pressure is not consistent exactly with practical pressure. It is important in this study to make a practical application for specialized nurses in order to verify the results and draw useful conclusions for predicting the use of this type of elastic band.
Abstract: In this work, an organic compound 5,10,15,20-
Tetrakis(3,5-di-tertbutylphenyl)porphyrinatocopper(II) (TDTBPPCu)
is studied as an active material for thin film electronic devices. To
investigate the electrical properties of TDTBPPCu, junction of
TDTBPPCu with heavily doped n-Si and Al is fabricated.
TDTBPPCu film was sandwiched between Al and n-Si electrodes.
Various electrical parameters of TDTBPPCu are determined. The
current-voltage characteristics of the junction are nonlinear,
asymmetric and show rectification behavior, which gives the clue of
formation of depletion region. This behavior indicates the potential
of TDTBPPCu for electronics applications. The current-voltage and
capacitance-voltage techniques are used to find the different
electronic parameters.
Abstract: We present a dextran modified silicon microring
resonator sensor for high density antibody immobilization. An array
of sensors consisting of three sensor rings and a reference ring was
fabricated and its surface sensitivity and the limit of detection were
obtained using polyelectrolyte multilayers. The mass sensitivity and
the limit of detection of the fabricated sensor ring are 0.35 nm/ng
mm-2 and 42.8 pg/mm2 in air, respectively. Dextran modified sensor
surface was successfully prepared by covalent grafting of oxidized
dextran on 3-aminopropyltriethoxysilane (APTES) modified silicon
sensor surface. The antibody immobilization on hydrogel dextran
matrix improves 40% compared to traditional antibody
immobilization method via APTES and glutaraldehyde linkage.
Abstract: The major objective of this study is to understand the
potential of a newly fabricated equipment to study the thermal
properties of nonwoven textile fabrics treated with aerogel at subzero
temperatures. Thermal conductivity was calculated by using the
empirical relation Fourier’s law, The relationship between the
thermal conductivity and thermal resistance of the samples were
studied at various environmental temperatures (which was set in the
clima temperature system between +25oC to -25oC). The newly
fabricated equipment was found to be a suitable for measuring at
subzero temperatures. This field of measurements is being developed
and will be the subject of further research which will be more suitable
for measurement of the various thermal characteristics.
Abstract: The nanofiber sheet of Multiwall Cabon Nanotube
(MWCNTs)/Polyacylonitile (PAN) composites was fabricated from
electrospun nanofiber. Firstly the surface of MWCNTs was
chemically modified, comparing two different techniques consisting
of admicellar polymerization and functionalization to improve the
dispersion and prevent the aggregation in the PAN matrix. The
modified MWCNTs were characterized by the dispersion in
dimethylformamide (DMF) solvent, Laser particle size, and FTRaman.
Lastly, DSC, SEM and mechanical properties of the
nanofiber sheet were examined. The results show that the mechanical
properties of the nanofiber sheet prepared from admicellar
polymerization-modified MWCNTs were higher than those of the
others.
Abstract: Fully customized hardware based technology provides high performance and low power consumption by specializing the tasks in hardware but lacks design flexibility since any kind of changes require re-design and re-fabrication. Software based solutions operate with software instructions due to which a great flexibility is achieved from the easy development and maintenance of the software code. But this execution of instructions introduces a high overhead in performance and area consumption. In past few decades the reconfigurable computing domain has been introduced which overcomes the traditional trades-off between flexibility and performance and is able to achieve high performance while maintaining a good flexibility. The dramatic gains in terms of chip performance and design flexibility achieved through the reconfigurable computing systems are greatly dependent on the design of their computational units being integrated with reconfigurable logic resources. The computational unit of any reconfigurable system plays vital role in defining its strength. In this research paper an RFU based computational unit design has been presented using the tightly coupled, multi-threaded reconfigurable cores. The proposed design has been simulated for VLIW based architectures and a high gain in performance has been observed as compared to the conventional computing systems.
Abstract: Process-oriented software development is a new
software development paradigm in which software design is modeled
by a business process which is in turn translated into a process
execution language for execution. The building blocks of this
paradigm are software units that are composed together to work
according to the flow of the business process. This new paradigm
still exhibits the characteristic of the applications built with the
traditional software component technology. This paper discusses an
approach to apply a traditional technique for software component
fabrication to the design of process-oriented software units, called
process components. These process components result from
decomposing a business process of a particular application domain
into subprocesses, and these process components can be reused to
design the business processes of other application domains. The
decomposition considers five managerial goals, namely cost
effectiveness, ease of assembly, customization, reusability, and
maintainability. The paper presents how to design or decompose
process components from a business process model and measure
some technical features of the design that would affect the
managerial goals. A comparison between the measurement values
from different designs can tell which process component design is
more appropriate for the managerial goals that have been set. The
proposed approach can be applied in Web Services environment
which accommodates process-oriented software development.
Abstract: An advanced composite flywheel rotor consisting of
intra and inter hybrid rims was designed to optimally increase the energy capacity, and was manufactured using filament winding with
in-situ curing. The flywheel has recently attracted considerable attention from many investigators since it possesses great potential in
many energy storage applications, including electric utilities, hybrid or
electric automobiles, and space vehicles. In this investigation, a comprehensive study was conducted with the intent to implement
composites in high performance flywheel applications.The inner two
intra-hybrid rims (rims 1 and 2) were manufactured as a whole part
through continuous filament winding under in-situ curing conditions,
and so were the outer two rims (rims 3 and 4). The outer surface of rim
2 and the inner surface of rim 3 were CNC-tapered for press-fitting. Machined rims were finally press-fitted using a hydraulic press with a
maximum compressive force of approximately 1000 ton.
Abstract: Finite impulse response (FIR) filters have the advantage of linear phase, guaranteed stability, fewer finite precision errors, and efficient implementation. In contrast, they have a major disadvantage of high order need (more coefficients) than IIR counterpart with comparable performance. The high order demand imposes more hardware requirements, arithmetic operations, area usage, and power consumption when designing and fabricating the filter. Therefore, minimizing or reducing these parameters, is a major goal or target in digital filter design task. This paper presents an algorithm proposed for modifying values and the number of non-zero coefficients used to represent the FIR digital pulse shaping filter response. With this algorithm, the FIR filter frequency and phase response can be represented with a minimum number of non-zero coefficients. Therefore, reducing the arithmetic complexity needed to get the filter output. Consequently, the system characteristic i.e. power consumption, area usage, and processing time are also reduced. The proposed algorithm is more powerful when integrated with multiplierless algorithms such as distributed arithmetic (DA) in designing high order digital FIR filters. Here the DA usage eliminates the need for multipliers when implementing the multiply and accumulate unit (MAC) and the proposed algorithm will reduce the number of adders and addition operations needed through the minimization of the non-zero values coefficients to get the filter output.
Abstract: This paper presented a modified efficient inductive
powering link based on ASK modulator and proposed efficient class-
E power amplifier. The design presents the external part which is
located outside the body to transfer power and data to the implanted
devices such as implanted Microsystems to stimulate and monitoring
the nerves and muscles. The system operated with low band
frequency 10MHZ according to industrial- scientific – medical (ISM)
band to avoid the tissue heating. For external part, the modulation
index is 11.1% and the modulation rate 7.2% with data rate 1 Mbit/s
assuming Tbit = 1us. The system has been designed using 0.35-μm
fabricated CMOS technology. The mathematical model is given and
the design is simulated using OrCAD P Spice 16.2 software tool and
for real-time simulation, the electronic workbench MULISIM 11 has
been used.
Abstract: This paper presents a new circuit arrangement for a
current-mode Wheatstone bridge that is suitable for low-voltage
integrated circuits implementation. Compared to the other proposed
circuits, this circuit features severe reduction of the elements number,
low supply voltage (1V) and low power consumption (
Abstract: Ultrathin (UTD) and Nanoscale (NSD) SOI-MOSFET devices, sharing a similar W/L but with a channel thickness of 46nm and 1.6nm respectively, were fabricated using a selective “gate recessed” process on the same silicon wafer. The electrical transport characterization at room temperature has shown a large difference between the two kinds of devices and has been interpreted in terms of a huge unexpected series resistance. Electrical characteristics of the Nanoscale device, taken in the linear region, can be analytically derived from the ultrathin device ones. A comparison of the structure and composition of the layers, using advanced techniques such as Focused Ion Beam (FIB) and High Resolution TEM (HRTEM) coupled with Energy Dispersive X-ray Spectroscopy (EDS), contributes an explanation as to the difference of transport between the devices.