Abstract: Infrared communication in the wavelength band 780-
950 nm is very suitable for short-range point-to-point communications.
It is a good choice for vehicle-to-vehicle communication in several
intelligent-transportation-system (ITS) applications such as cooperative
driving, collision warning, and pileup-crash prevention. In this
paper, with the aid of a physical model established in our previous
works, we explore the communication area of an infrared intervehicle
communication system utilizing a typical low-cost cormmercial lightemitting
diodes (LEDs) as the emitter and planar p-i-n photodiodes
as the receiver. The radiation pattern of the emitter fabricated by
aforementioned LEDs and the receiving pattern of the receiver are
approximated by a linear combination of cosinen functions. This
approximation helps us analyze the system performance easily. Both
multilane straight-road conditions and curved-road conditions with
various radius of curvature are taken into account. The condition of
a small car communicating with a big truck, i.e., there is a vertical
mounting height difference between the emitter and the receiver, is
also considered. Our results show that the performance of the system
meets the requirement of aforementioned ITS applications in terms
of the communication area.
Abstract: In this paper, we present a vertical nanowire thin film transistor with gate-all-around architecture, fabricated using CMOS compatible processes. A novel method of fabricating polysilicon vertical nanowires of diameter as small as 30 nm using wet-etch is presented. Both n-type and p-type vertical poly-silicon nanowire transistors exhibit superior electrical characteristics as compared to planar devices. On a poly-crystalline nanowire of 30 nm diameter, high Ion/Ioff ratio of 106, low drain-induced barrier lowering (DIBL) of 50 mV/V, and low sub-threshold slope SS~100mV/dec are demonstrated for a device with channel length of 100 nm.
Abstract: This paper presents the design and implementation of a fully integrated transimpedance amplifier (TIA) as the analog frontend receiver for Capacitive Micromachined Ultrasound Transducers (CMUTs) for ultrasound biomicroscope imaging application. The amplifier is designed to amplify the received signals from 17.5MHz to 52.5MHz with a center frequency of 35MHz. The TIA was fabricated in GF 0.18μm 1P6M 30V high voltage process. The measurement results show that the designed amplifier can reach a transimpedance gain of 61.08dBΩ and operating frequency from 17.5MHz to 100MHz with 1VP-P output voltage under 6V power supply.
Abstract: Aims of this research were to study Thai Buddhist temple festivals and Balinese Hindu temple festivals, to compare Thai Buddhist temple festival dress with Balinese Hindu temple festival dress, and to create the knowledge which can be useful for Thai attitudes and cultural perceptions, especially for Thai children and youth. The findings of the research disclosed that there are four temple festivals of Thai Buddhists in Thailand, namely Songkran Festival, Buddhist Lent Festival, Sart Thai Festival and End of Buddhist Lent Festival. In island of Bali, Indonesia, there are three Balinese Hindu temple festivals, namely Odalan Festival, Galungan Festival and Nyepi Festival. Thai Songkran Festival is similar to New Year Celebration in Balinese Nyepi Festival. Thai Songkran Festival and Sart Thai Festival have the same purpose as that of Balinese Galungan Festival in practice of dedicating merit to the spirits of deceased relatives. In these temple festivals, Thai Buddhist men will wear round collar outerwear and wide leg trousers or loincloths but will never wear headdresses, while Balinese Hindu men wear turbans or fabric headbands, shirts and Sarong, which are similar to Sarong of Thai Buddhist men in central and northern part of Thailand. Most of Thai Buddhist women wear Sarong like Balinese Hindu women but wear only round collar outerwear, while Balinese Hindu women wear diamond neck camisole as inner wear and shawl collar as outerwear.
Abstract: The objective of this research is to investigate the
advantages of using large-diameter 0.7 inch prestressing strands in
pretention applications. The advantages of large-diameter strands are
mainly beneficial in the heavy construction applications. Bridges and
tunnels are subjected to a higher daily traffic with an exponential
increase in trucks ultimate weight, which raise the demand for higher
structural capacity of bridges and tunnels. In this research, precast
prestressed I-girders were considered as a case study. Flexure
capacities of girders fabricated using 0.7 inch strands and different
concrete strengths were calculated and compared to capacities of 0.6
inch strands girders fabricated using equivalent concrete strength.
The effect of bridge deck concrete strength on composite deck-girder
section capacity was investigated due to its possible effect on final
section capacity. Finally, a comparison was made to compare the
bridge cross-section of girders designed using regular 0.6 inch strands
and the large-diameter 0.7 inch. The research findings showed that
structural advantages of 0.7 inch strands allow for using fewer bridge
girders, reduced material quantity, and light-weight members. The
structural advantages of 0.7 inch strands are maximized when high
strength concrete (HSC) are used in girder fabrication, and concrete
of minimum 5ksi compressive strength is used in pouring bridge
decks. The use of 0.7 inch strands in bridge industry can partially
contribute to the improvement of bridge conditions, minimize
construction cost, and reduce the construction duration of the project.
Abstract: The National Bridge Inventory (NBI) includes more
than 600,000 bridges within the United States of America.
Prestressed concrete girder bridges represent one of the most widely
used bridge systems. The majority of these girder bridges were
constructed using 0.5 and 0.6 inch diameter strands. The main
impediments to using larger strand diameters are: 1) lack of prestress
bed capacities, 2) lack of structural knowledge regarding the transfer
and development length of larger strands, and 3) the possibility of
developing wider end zone cracks upon strand release.
This paper presents a study about using 0.7 inch strands in girder
fabrication. Transfer and development length were evaluated, and
girders were fabricated using 0.7 inch strands at different spacings.
Results showed that 0.7 inch strands can be used at 2.0 inch spacing
without violating the AASHTO LRFD Specifications, while attaining
superior performance in shear and flexure.
Abstract: Capacitive electrocardiogram (ECG) measurement is an attractive approach for long-term health monitoring. However, there is little literature available on its implementation, especially for multichannel system in standard ECG leads. This paper begins from the design criteria for capacitive ECG measurement and presents a multichannel limb-lead capacitive ECG system with conductive fabric tapes pasted on a double layer PCB as the capacitive sensors. The proposed prototype system incorporates a capacitive driven-body (CDB) circuit to reduce the common-mode power-line interference (PLI). The presented prototype system has been verified to be stable by theoretic analysis and practical long-term experiments. The signal quality is competitive to that acquired by commercial ECG machines. The feasible size and distance of capacitive sensor have also been evaluated by a series of tests. From the test results, it is suggested to be greater than 60 cm2 in sensor size and be smaller than 1.5 mm in distance for capacitive ECG measurement.
Abstract: The present work consecutively on synthesis and
characterization of composites, Al/Al alloy A 384.1 as matrix in
which the main ingredient as Al/Al-5% MgO alloy based metal
matrix composite. As practical implications the low cost processing
route for the fabrication of Al alloy A 384.1 and operational
difficulties of presently available manufacturing processes based in
liquid manipulation methods. As all new developments, complete
understanding of the influence of processing variables upon the final
quality of the product. And the composite is applied comprehensively
to the acquaintance for achieving superiority of information
concerning the specific heat measurement of a material through the
aid of thermographs. Products are evaluated concerning relative
particle size and mechanical behavior under tensile strength.
Furthermore, Taguchi technique was employed to examine the
experimental optimum results are achieved, owing to effectiveness of
this approach.
Abstract: In this paper, a low noise microwave bandpass filter
(BPF) is presented. This filter is fabricated by modifying the
conventional cross-coupled structure. The spurious response is
improved by using the end open coupled lines, and the influence of the
noise is minimized. Impedance matrix of the open end coupled circuit
clarifies the characteristic of the suppression of the spurious response.
The rejection of spurious suppression region of the proposed filter is
greater than 20 dB from 3-13 GHz. The measured results of the
fabricated filter confirm the concepts of the proposed design and
exhibits high performance.
Abstract: We report a lithography-free approach to fabricate the
biomimetics, quasi-beehive Si nanostructures (QBSNs), on
Si-substrates. The self-assembled SiGe nanoislands via the strain
induced surface roughening (Asaro-Tiller-Grinfeld instability) during
in-situ annealing play a key role as patterned sacrifice regions for
subsequent reactive ion etching (RIE) process performed for
fabricating quasi-beehive nanostructures on Si-substrates. As the
measurements of field emission, the bare QBSNs show poor field
emission performance, resulted from the existence of the native oxide
layer which forms an insurmountable barrier for electron emission. In
order to dramatically improve the field emission characteristics, the
platinum nanopillars (Pt-NPs) were deposited on QBSNs to form
Pt-NPs/QBSNs heterostructures. The turn-on field of Pt-NPs/QBSNs
is as low as 2.29 V/μm (corresponding current density of 1 μA/cm2),
and the field enhancement factor (β-value) is significantly increased to
6067. More importantly, the uniform and continuous electrons excite
light emission, due to the surrounding filed emitters from
Pt-NPs/QBSNs, can be easily obtained. This approach does not require
an expensive photolithographic process and possesses great potential
for applications.
Abstract: This paper proposes a robot able to climb Columns.
This robot is not dependent on the diameter and material of the
columns. Some climbing robots have been designed up to now but
Koala robot was designed and fabricated for climbing columns
exclusively. Simple kinematics of climbing in the nature inspired us
to design this robot. We used two linear mechanisms to grip the
column. The gripper consists of a DC motor and a power screw
mechanism with a linear bushing as a guide. This mechanism
provides enough force to grip the column. In addition we needed an
actuator for climbing the column; hence, two pneumatic jacks were
used. All the mechanical parts were designed according to the
exerted forces and operational condition. The prototype can be
simply installed and controlled on the column by an inexperienced
operator. This robot is intended for inspection and surveillance of
pipes in oil industries and power poles in electric industries.
Abstract: This report shows the performance of composite
biodegradable film from chitosan, starch and sawdust fiber. The main
objectives of this research are to fabricate and characterize composite
biodegradable film in terms of morphology and physical properties.
The film was prepared by casting method. Sawdust fiber was used as
reinforcing agent and starch as polymer matrix in the casting
solution. The morphology of the film was characterized using atomic
force microscope (AFM). The result showed that the film has
smooth structure. Chemical composition of the film was investigated
using Fourier transform infrared (FTIR) where the result revealed
present of starch in the film. The thermal properties were
characterized using thermal gravimetric analyzer (TGA) and
differential scanning calorimetric (DSC) where the results showed
that the film has small difference in melting and degradation
temperature.
Abstract: Graphene-metal contact resistance limits the performance of graphene-based electrical devices. In this work, we have fabricated both graphene field-effect transistors (GFET) and transfer length measurement (TLM) test devices with titanium contacts. The purpose of this work is to compare the contact resistances that can be numerically extracted from the GFETs and measured from the TLM structures. We also provide a brief review of the work done in the field to solve the contact resistance problem.
Abstract: ZnO heteronanostructured nanowires arrays have
been fabricated by low temperature solution method. Various
heterostructures were synthesized including CdS/ZnO,
CdSe/CdS/ZnO nanowires and Co3O4/ZnO, ZnO/SiC
nanowires. These multifunctional heterostructure nanowires
showed important applications in photocatalysts, sensors,
wettability control and solar energy conversion.
Abstract: These This paper looks into frameworks which aim at
furthering the discussion of the role of regenerative design practices
in a city-s historic core and the tool of urban design to achieve urban
revitalization on the island of Cyprus. It also examines the region-s
demographic mix, the effectiveness of its governmental coordination
and the strategies of adaptive reuse and strategic investments in older
areas with existing infrastructure. The two main prongs of
investigation will consider the effect of the existing and proposed
changes in the physical infrastructure and fabric of the city, as well as
the catalytic effect of sustainable urban design practices. Through this
process, the work hopes to integrate the contained potential within
the existing historic core and the contributions and participation of
the migrant and immigrant populations to the local economy. It also
examines ways in which this coupling of factors can bring to the front
the positive effects of this combined effort on an otherwise sluggish
local redevelopment effort. The data for this study is being collected
and organized as part of ongoing urban design and development
student workshop efforts in urban planning and design education.
The work is presented in graphic form and includes data collected
from interviews with study area organizations and the community at
large. Planning work is also based on best practices initiated by the
staff of the Nicosia Master Plan task force, which coordinates holistic
planning efforts for the historic center of the city of Nicosia.
Abstract: This paper presents a low cost design of heart beat monitoring device using reflectance mode PhotoPlethysmography (PPG). PPG is known for its simple construction, ease of use and cost effectiveness and can provide information about the changes in cardiac activity as well as aid in earlier non-invasive diagnostics. The proposed device is divided into three phases. First is the detection of pulses through the fingertip. The signal is then passed to the signal processing unit for the purpose of amplification, filtering and digitizing. Finally the heart rate is calculated and displayed on the computer using parallel port interface. The paper is concluded with prototyping of the device followed by verification procedure of the heartbeat signal obtained in laboratory setting.
Abstract: Adhesively bonded joints are preferred over the
conventional methods of joining such as riveting, welding, bolting
and soldering. Some of the main advantages of adhesive joints
compared to conventional joints are the ability to join dissimilar
materials and damage-sensitive materials, better stress distribution,
weight reduction, fabrication of complicated shapes, excellent
thermal and insulation properties, vibration response and enhanced
damping control, smoother aerodynamic surfaces and an
improvement in corrosion and fatigue resistance. This paper presents
the behavior of adhesively bonded joints subjected to combined
thermal loadings, using the numerical methods. The joint
configuration considers aluminum as central adherend with six
different outer adherends including aluminum, steel, titanium, boronepoxy,
unidirectional graphite-epoxy and cross-ply graphite-epoxy
and epoxy-based adhesives. Free expansion of the joint in x
direction was permitted and stresses in adhesive layer and interfaces
calculated for different adherends.
Abstract: Proper management of residues originated from
industrial activities is considered as one of the serious challenges
faced by industrial societies due to their potential hazards to the
environment. Common disposal methods for industrial solid wastes
(ISWs) encompass various combinations of solely management
options, i.e. recycling, incineration, composting, and sanitary
landfilling. Indeed, the procedure used to evaluate and nominate the
best practical methods should be based on environmental, technical,
economical, and social assessments. In this paper an environmentaltechnical
assessment model is developed using analytical network
process (ANP) to facilitate the decision making practice for ISWs
generated at Gilan province, Iran. Using the results of performed
surveys on industrial units located at Gilan, the various groups of
solid wastes in the research area were characterized, and four
different ISW management scenarios were studied. The evaluation
process was conducted using the above-mentioned model in the
Super Decisions software (version 2.0.8) environment. The results
indicates that the best ISW management scenario for Gilan province
is consist of recycling the metal industries residues, composting the
putrescible portion of ISWs, combustion of paper, wood, fabric and
polymeric wastes as well as energy extraction in the incineration
plant, and finally landfilling the rest of the waste stream in addition
with rejected materials from recycling and compost production plants
and ashes from the incineration unit.
Abstract: An innovative tri-axes micro-power receiver is
proposed. The tri-axes micro-power receiver consists of two sets 3-D
micro-solenoids and one set planar micro-coils in which iron core is
embedded. The three sets of micro-coils are designed to be orthogonal
to each other. Therefore, no matter which direction the flux is present
along, the magnetic energy can be harvested and transformed into
electric power. Not only dead space of receiving power is mostly
reduced, but also transformation efficiency of electromagnetic energy
to electric power can be efficiently raised. By employing commercial
software, Ansoft Maxwell, the preliminary simulation results verify
that the proposed micro-power receiver can efficiently pick up the
energy transmitted by magnetic power source.
As to the fabrication process, the isotropic etching technique is
employed to micro-machine the inverse-trapezoid fillister so that the
copper wire can be successfully electroplated. The adhesion between
micro-coils and fillister is much enhanced.
Abstract: Mathematical justifications are given for a simulation technique of multivariate nonGaussian random processes and fields based on Rosenblatt-s transformation of Gaussian processes. Different types of convergences are given for the approaching sequence. Moreover an original numerical method is proposed in order to solve the functional equation yielding the underlying Gaussian process autocorrelation function.