Abstract: This paper made an attempt to investigate the problem associated with enhancement of emulsions of light crude oil-water recovery in an oil field of Algerian Sahara. Measurements were taken through experiments using RheoStress (RS600). Factors such as shear rate, temperature and light oil concentration on the viscosity behavior were considered. Experimental measurements were performed in terms of shear stress–shear rate, yield stress and flow index on mixture of light crude oil–water. The rheological behavior of emulsion showed Non-Newtonian shear thinning behavior (Herschel-Bulkley). The experiments done in the laboratory showed the stability of some water in light crude oil emulsions form during consolidate oil recovery process. To break the emulsion using additives may involve higher cost and could be very expensive. Therefore, further research should be directed to find solution of these problems that have been encountered.
Abstract: Study of fire and explosion is very important mainly
in oil and gas industries due to several accidents which have been
reported in the past and present. In this work, we have investigated
the flammability of bio oil vapour mixtures. This mixture may
contribute to fire during the storage and transportation process. Bio
oil sample derived from Palm Kernell shell was analysed using Gas
Chromatography Mass Spectrometry (GC-MS) to examine the
composition of the sample. Mole fractions of 12 selected
components in the liquid phase were obtained from the GC-FID data
and used to calculate mole fractions of components in the gas phase
via modified Raoult-s law. Lower Flammability Limits (LFLs) and
Upper Flammability Limits (UFLs) for individual components were
obtained from published literature. However, stoichiometric
concentration method was used to calculate the flammability limits
of some components which their flammability limit values are not
available in the literature. The LFL and UFL values for the mixture
were calculated using the Le Chatelier equation. The LFLmix and
UFLmix values were used to construct a flammability diagram and
subsequently used to determine the flammability of the mixture. The
findings of this study can be used to propose suitable inherently
safer method to prevent the flammable mixture from occurring and
to minimizing the loss of properties, business, and life due to fire
accidents in bio oil productions.
Abstract: Independent component analysis can estimate unknown
source signals from their mixtures under the assumption that the
source signals are statistically independent. However, in a real environment,
the separation performance is often deteriorated because
the number of the source signals is different from that of the sensors.
In this paper, we propose an estimation method for the number of
the sources based on the joint distribution of the observed signals
under two-sensor configuration. From several simulation results, it
is found that the number of the sources is coincident to that of
peaks in the histogram of the distribution. The proposed method can
estimate the number of the sources even if it is larger than that of
the observed signals. The proposed methods have been verified by
several experiments.
Abstract: In this study, we sought to investigate the mercury
removal efficiency of manganese oxides from natural gas. The
fundamental studies on mercury removal with manganese oxides
sorbents were carried out in a laboratory scale fixed bed reactor at 30
°C with a mixture of methane (20%) and nitrogen gas laden with 4.8
ppb of elemental mercury. Manganese oxides with varying surface
area and crystalline phase were prepared by conventional precipitation
method in this study. The effects of surface area, crystallinity and
other metal oxides on mercury removal efficiency were investigated.
Effect of Ag impregnation on mercury removal efficiency was also
investigated. Ag supported on metal oxide such titania and zirconia as
reference materials were also used in this study for comparison. The
characteristics of mercury removal reaction with manganese oxide
was investigated using a temperature programmed desorption (TPD)
technique.
Manganese oxides showed very high Hg removal activity (about
73-93% Hg removal) for first time use. Surface area of the manganese
oxide samples decreased after heat-treatment and resulted in complete
loss of Hg removal ability for repeated use after Hg desorption in the
case of amorphous MnO2, and 75% loss of the initial Hg removal
activity for the crystalline MnO2. Mercury desorption efficiency of
crystalline MnO2 was very low (37%) for first time use and high (98%)
after second time use. Residual potassium content in MnO2 may have
some effect on the thermal stability of the adsorbed Hg species.
Desorption of Hg from manganese oxides occurs at much higher
temperatures (with a peak at 400 °C) than Ag/TiO2 or Ag/ZrO2.
Mercury may be captured on manganese oxides in the form of mercury
manganese oxide.
Abstract: Due to urbanization, trees and plants which covered a great land mass of the earth and are an excellent carbon dioxide (CO2) absorber through photosynthesis are being replaced by several concrete based structures. It is therefore important to have these cement based structures absorb the large volume of carbon dioxide which the trees would have removed from the atmosphere during their useful lifespan. Hence the need for these cement based structures to be designed to serve other useful purposes in addition to shelter. This paper reviews the properties of Sodium carbonate and sugar as admixtures in concrete with respect to improving carbon sequestration in concrete.
Abstract: Studying alternative raw materials for biodiesel production is of major importance. The use of mixtures with incorporation of wastes is an environmental friendly alternative and might reduce biodiesel production costs. The objective of the present work was: (i) to study biodiesel production using waste frying oil mixed with pork lard and (ii) to understand how mixture composition influences biodiesel quality. Biodiesel was produced by transesterification and quality was evaluated through determination of several parameters according to EN 14214. The weight fraction of lard in the mixture varied from 0 to 1 in 0.2 intervals. Biodiesel production yields varied from 81.7 to 88.0 (wt%), the lowest yields being the ones obtained using waste frying oil and lard alone as raw materials. The obtained products fulfilled most of the determined quality specifications according to European biodiesel quality standard EN 14214. Minimum purity (96.5 wt%) was closely obtained when waste frying oil was used alone and when 0.2% of lard was incorporated in the raw material (96.3 wt%); however, it ranged from 93.9 to 96.3 (wt%) being always close to the limit. From the evaluation of the influence of mixture composition in biodiesel quality, it was possible to establish a model to be used for predicting some parameters of biodiesel resulting from mixtures of waste frying oil with lard when different lard contents are used.
Abstract: In order to characterize the soy protein hydrolysate obtained in this study, gel chromatography on Sephadex G-25 was used to perform the separation of the peptide mixture and electrophoresis in SDS-polyacrylamide gel has been employed. Protein hydrolysate gave high antioxidant activities, but didn't give any antimicrobial activities. The antioxidant activities of protein hydrolysate was in the same trend of peptide content which gave high antioxidant activities and high peptide content between fractions 15 to 50. With increasing peptide concentrations, the scavenging effect on DPPH radical increased until about 70%, thereafter reaching a plateau. In compare to different concentrations of BHA, which exhibited higher activity (90%), soybean protein hydrolysate exhibited high antioxidant activities (70%) at a concentration of 1.45 mg/ml at fraction 25. Electrophoresis analysis indicated that, low- MW hydrolysate fractions (F1) appeared, on average, to have higher DPPH scavenging activities than high-MW fractions. These results revealed that soybean peptides probably contain substances that were proton donors and could react with free radicals to convert them to stable diamagnetic molecules.
Abstract: The pyrolysis of hazelnut shell, polyethylene oxide and their blends were carried out catalytically at 500 and 650 ºC. Potassium dichromate was chosen according to its oxidative characteristics and decomposition temperature (500 ºC) where decomposition products are CrO3 and K2CrO4. As a main effect, a remarkable increase in gasification was observed using this catalyst for pure components and blends especially at 500 ºC rather than 650 ºC contrary to the main observation in the pyrolysis process. The increase in gas product quantity was compensated mainly with decrease in solid product and additionally in some cases liquid products.
Abstract: The present work deals with optimization of cascade refrigeration system using eco friendly refrigerants pair R507A and R23. R507A is azeotropic mixture composed of HFC refrigerants R125/R143a (50%/50% by wt.). R23 is a single component HFC refrigerant used as replacement to CFC refrigerant R13 in low temperature applications. These refrigerants have zero ozone depletion potential and are non-flammable. Optimization of R507AR23 cascade refrigeration system performance parameters such as minimum work required, refrigeration effect, coefficient of performance and exergetic efficiency was carried out in terms of eight operating parameters- combinations using Genetic Algorithm tool. The eight operating parameters include (1) low side evaporator temperature (2) high side condenser temperature (3) temperature difference in the cascade heat exchanger (4) low side condenser temperature (5) low side degree of subcooling (6) high side degree of subcooling (7) low side degree of superheating (8) high side degree of superheating. Results show that for minimum work system should operate at high temperature in low side evaporator, low temperature in high side condenser, low temperature difference in cascade condenser, high temperature in low side condenser and low degree of subcooling and superheating in both side. For maximum refrigeration effect system should operate at high temperature in low side evaporator, high temperature in high side condenser, high temperature difference in cascade condenser, low temperature in low side condenser and higher degree of subcooling in LT and HT side. For maximum coefficient of performance and exergetic efficiency, system should operate at high temperature in low side evaporator, low temperature in high side condenser, low temperature difference in cascade condenser, high temperature in low side condenser and higher degree of subcooling and superheating in low side of the system.
Abstract: Agricultural waste is mainly composed of cellulose
and hemicelluloses which can be converted to sugars. The
inexpensive reducing sugar from durian peel was obtained by
hydrolysis with HCl concentration at 0.5-2.0% (v/v). The hydrolysis
range of time was for 15-60 min when the mixture was autoclaved at
121 °C. The result showed that acid hydrolysis efficiency (AHE)
highest to 80.99% at condition is 2.0%concentration for 15 min.
Reducing sugar highest to 56.07 g/litre at condition is 2.0%
concentration for 45min. Total sugar highest to 59.83 g/litre at
condition is 2.0%concentration for 45min, which was not significant
(p < 0.05) with condition 2.0% concentration for 30 min and 1.5 %
concentration for 45 and 60 min. The increase in concentration
increased AHE, reducing sugar and total sugar. The hydrolysis time
had no effect on AHE, reducing sugar and total sugar. The maximum
reducing sugars of each concentration were at hydrolysis time 45
min .The hydrolysated were analysis by HPLC, the results revealed
that the principle of sugar were glucose, fructose and xylose.
Abstract: Attempt was made to improve certain characteristics of bio-oil derived from palm kernel pyrolysis by blending it with diesel fuel and alcohols. Two types of alcohol, ethanol or butanol, was used as cosolvent to stabilize the phase of ternary systems. Phase behaviors and basic fuel properties of palm kernel bio-oildiesel- alcohol systems were investigated in this study. Alcohol types showed a significant influence on the phase characteristics with palm kernel bio-oil-diesel-butanol system giving larger soluble area than that of palm kernel bio-oil-diesel-ethanol system. For fuel properties, blended fuels showed superior properties including lower values of density (~860 kg/m3 at 25°C), viscosity (~4.12 mm2/s at 40°C), carbon residue (1.02-2.53 wt%), ash (0.018-0.034 wt%) and pour point (
Abstract: This paper proposes a novel approach that combines statistical models and support vector machines. A hybrid scheme which appropriately incorporates the advantages of both the generative and discriminant model paradigms is described and evaluated. Support vector machines (SVMs) are trained to divide the whole speakers' space into small subsets of speakers within a hierarchical tree structure. During testing a speech token is assigned to its corresponding group and evaluation using gaussian mixture models (GMMs) is then processed. Experimental results show that the proposed method can significantly improve the performance of text independent speaker identification task. We report improvements of up to 50% reduction in identification error rate compared to the baseline statistical model.
Abstract: Anaerobic digestion process is one of the alternative
methods to convert organic waste into methane gas which is a fuel
and energy source. Activities of various kinds of microorganisms are
the main factor for anaerobic digestion which produces methane gas.
Therefore, in this study a modified Anaerobic Baffled Reactor (ABR)
with working volume of 50 liters was designed to identify the
microorganisms through biogas production. The mixture of 75%
kitchen waste and 25% sewage sludge was used as substrate.
Observations on microorganisms in the ABR showed that there exists
a small amount of protozoa (5%) and fungi (2%) in the system, but
almost 93% of the microorganism population consists of bacteria. It
is definitely clear that bacteria are responsible for anaerobic
biodegradation of kitchen waste. Results show that in the
acidification zone of the ABR (front compartments of reactor) fast
growing bacteria capable of growth at high substrate levels and
reduced pH was dominant. A shift to slower growing scavenging
bacteria that grow better at higher pH was occurring towards the end
of the reactor. Due to the ability of activity in acetate environment the
percentages of Methanococcus, Methanosarcina and Methanotrix
were higher than other kinds of methane former in the system.
Abstract: During 2011 and 2012 seasons, Zaghloul date palms received four sprays of silicon (Si) at 0.05 to 0.1% and selenium (Se) at 0.01 to 0.02%. Growth, nutritional status, yield as well as physical and chemical characteristics of the fruits in response to application of silicon and selenium were investigated. Single and combined applications of silicon at 0.05 to 0.1% and selenium at 0.01 to 0.02% was very effective in enhancing the leaf area, total chlorophylls, percentages of N, P and K in the leaves, yield, bunch weight as well as physical and chemical characteristics of the fruits in relative to the check treatment. Silicon was superior to selenium in this respect. Combined application was favorable than using each alone in this connection. Treating Zaghloul date palms four times with a mixture of silicon at 0.05% + selenium at 0.01% resulted in an economical yield and producing better fruit quality.
Abstract: In Secondary Surveillance Radar (SSR) systems, it is
more difficult to locate and recognise aircrafts in the neighbourhood of civil airports since aerial traffic becomes greater. Here, we propose to apply a recent Blind Source Separation (BSS) algorithm based
on Time-Frequency Analysis, in order to separate messages sent by different aircrafts and falling in the same radar beam in reception. The above source separation method involves joint-diagonalization
of a set of smoothed version of spatial Wigner-Ville distributions.
The technique makes use of the difference in the t-f signatures of the nonstationary sources to be separated. Consequently, as the SSR sources emit different messages at different frequencies, the above fitted to this new application. We applied the technique in simulation to separate SSR replies. Results are provided at the end
of the paper.
Abstract: Recently many research has been conducted to
retrieve pertinent parameters and adequate models for automatic
music genre classification. In this paper, two measures based upon
information theory concepts are investigated for mapping the features
space to decision space. A Gaussian Mixture Model (GMM) is used
as a baseline and reference system. Various strategies are proposed
for training and testing sessions with matched or mismatched
conditions, long training and long testing, long training and short
testing. For all experiments, the file sections used for testing are
never been used during training. With matched conditions all
examined measures yield the best and similar scores (almost 100%).
With mismatched conditions, the proposed measures yield better
scores than the GMM baseline system, especially for the short testing
case. It is also observed that the average discrimination information
measure is most appropriate for music category classifications and on
the other hand the divergence measure is more suitable for music
subcategory classifications.
Abstract: In this work, axisymetric CFD simulation of fixed bed
GTL reactor has been conducted, using computational fluid dynamics
(CFD). In fixed bed CFD modeling, when N (tube-to-particle
diameter ratio) has a large value, it is common to consider the packed
bed as a porous media. Synthesis gas (a mixture of predominantly
carbon monoxide and hydrogen) was fed to the reactor. The reactor
length was 20 cm, divided to three sections. The porous zone was in
the middle section of the reactor. The model equations were solved
employing finite volume method. The effects of particle diameter,
bed voidage, fluid velocity and bed length on pressure drop have
been investigated. Simulation results showed these parameters could
have remarkable impacts on the reactor pressure drop.
Abstract: The usefulness of weaning foods to meet the nutrient
needs of children is well recognized, and most of them are precooked
roller dried mixtures of cereal and/or legume flours which posses a
high viscosity and bulk when reconstituted. The objective of this study
was to formulate composite weaning foods using cereals, malted
legumes and vegetable powders and analyze them for nutrients,
functional properties and sensory attributes. Selected legumes (green
gram and lentil) were germinated, dried and dehulled. Roasted wheat,
rice, carrot powder and skim milk powder also were used. All the
ingredients were mixed in different proportions to get four
formulations, made into 30% slurry and dried in roller drier. The
products were analyzed for proximate principles, mineral content,
functional and sensory qualities. The results of analysis showed
following range of constituents per 100g of formulations on dry
weight basis, protein, 18.1-18.9 g ; fat, 0.78-1.36 g ; iron, 5.09-6.53
mg; calcium, 265-310 mg. The lowest water absorption capacity was
in case of wheat green gram based and the highest was in rice lentil
based sample. Overall sensory qualities of all foods were graded as
“good" and “very good" with no significant differences. The results
confirm that formulated weaning foods were nutritionally superior,
functionally appropriate and organoleptically acceptable.
Abstract: To understand working features of a micro combustor,
a computer code has been developed to study combustion of
hydrogen–air mixture in a series of chambers with same shape aspect
ratio but various dimensions from millimeter to micrometer level.
The prepared algorithm and the computer code are capable of
modeling mixture effects in different fluid flows including chemical
reactions, viscous and mass diffusion effects. The effect of various
heat transfer conditions at chamber wall, e.g. adiabatic wall, with
heat loss and heat conduction within the wall, on the combustion is
analyzed. These thermal conditions have strong effects on the
combustion especially when the chamber dimension goes smaller and
the ratio of surface area to volume becomes larger.
Both factors, such as larger heat loss through the chamber wall
and smaller chamber dimension size, may lead to the thermal
quenching of micro-scale combustion. Through such systematic
numerical analysis, a proper operation space for the micro-combustor
is suggested, which may be used as the guideline for microcombustor
design. In addition, the results reported in this paper
illustrate that the numerical simulation can be one of the most
powerful and beneficial tools for the micro-combustor design,
optimization and performance analysis.
Abstract: Ethanol has become more attractive in fuel industry
either as fuel itself or an additive that helps enhancing the octane
number and combustibility of gasoline. This research studied a
pressure swing adsorption using cassava-based adsorbent prepared
from mixture of cassava starch and cassava pulp for dehydration of
ethanol vapor. The apparatus used in the experiments consisted of
double adsorption columns, an evaporator, and a vacuum pump. The
feed solution contained 90-92 %wt of ethanol. Three process
variables: adsorption temperatures (110, 120 and 130°C), adsorption
pressures (1 and 2 bar gauge) and feed vapor flow rate (25, 50 and 75
% valve opening of the evaporator) were investigated. According to
the experimental results, the optimal operating condition for this
system was found to be at 2 bar gauge for adsorption pressure, 120°C
for adsorption temperature and 25% valve opening of the evaporator.
Production of 1.48 grams of ethanol with concentration higher than
99.5 wt% per gram of adsorbent was obtained. PSA with cassavabased
adsorbent reported in this study could be an alternative method
for production of nearly anhydrous ethanol. Dehydration of ethanol
vapor achieved in this study is due to an interaction between free
hydroxyl group on the glucose units of the starch and the water
molecules.