Abstract: Climate change and environmental pressures are
major international issues nowadays. It is time when governments,
businesses and consumers have to respond through more
environmentally friendly and aware practices, products and policies.
This is the prime time to develop alternative sustainable construction
materials, reduce greenhouse gas emissions, save energy, look to
renewable energy sources and recycled materials, and reduce waste.
The utilization of waste materials (slag, fly ash, glass beads, plastic
and so on) in concrete manufacturing is significant due to its
engineering, financial, environmental and ecological benefits. Thus,
utilization of waste materials in concrete production is very much
helpful to reach the goal of the sustainable construction. Therefore,
this study intends to use glass beads in concrete production.
The paper reports on the performance of 9 different concrete
mixes containing different ratios of glass crushed to 5 mm - 20 mm
maximum size and glass marble of 20 mm size as coarse aggregate.
Ordinary Portland cement type 1 and fine sand less than 0.5 mm were
used to produce standard concrete cylinders. Compressive strength
tests were carried out on concrete specimens at various ages. Test
results indicated that the mix having the balanced ratio of glass beads
and round marbles possess maximum compressive strength which is
3889 psi, as glass beads perform better in bond formation but have
lower strength, on the other hand marbles are strong in themselves
but not good in bonding. These mixes were prepared following a
specific W/C and aggregate ratio; more strength can be expected to
achieve from different W/C, aggregate ratios, adding admixtures like
strength increasing agents, ASR inhibitor agents etc.
Abstract: Desert regions around the Nile valley in Upper Egypt
contain great extent of swelling soil. Many different comment
procedures of treatment of the swelling soils for construction such as
pre-swelling, load balance OR soil replacement. One of the measure
factors which affect the level of the aggressiveness of the swelling
soil is the direction of the infiltration water directions within the
swelling soils. In this paper a physical model was installed to
measure the effect of water on the swelling soil with replacement
using fatty acid distillation residuals (FADR) mixed with sand as
thick sand-FADR mixture to prevent the water pathway arrive to the
swelling soil. Testing program have been conducted on different
artificial samples with different sand to FADR contents ratios (4%,
6%, and 9%) to get the optimum value fulfilling the impermeable
replacement. The tests show that a FADR content of 9% is sufficient
to produce impermeable replacement.
Abstract: Asphalt surfaces are exposed to various weather
conditions and dynamic loading caused by passing trucks and
vehicles. In such situations, asphalt cement shows so different
rheological-mechanical behavior. If asphalt cement isn-t compatible
enough, asphalt layer will be damaged immediately and expensive
repairing procedures should be performed then. To overcome this
problem, researchers study on mechanical improved asphalt cement.
In this study, bentonite was used in order to modify bitumen
characteristics and the modified bitumen's characteristics were
investigated by asphalt cement tests. Then, the optimal bitumen
content in various compounds was determined and asphalt samples
with different contents of additives were prepared and tested. Results
show using this kind of additive not only has caused improvement in
bitumen mechanical properties, but also improvement in Marshall
Parameters was achieved.
Abstract: Utilization of waste material in asphalt pavement
would be beneficial in order to find an alternative solution to increase
service life of asphalt pavement and reduce environmental pollution
as well. One of these waste materials is Polyethylene Terephthalate
(PET) which is a type of polyester material and is produced in a large
extent. This research program is investigating the effects of adding
waste PET particles into the asphalt mixture with a maximum size of
2.36 mm. Different percentages of PET were added into the mixture
during dry process. Gap-graded mixture (SMA 14) and PG 80-100
asphalt binder have been used for this study. To evaluate PET
reinforced asphalt mixture different laboratory investigations have
been conducted on specimens. Marshall Stability test was carried
out. Besides, stiffness modulus test and indirect tensile fatigue test
were conducted on specimens at optimum asphalt content. It was
observed that in many cases PET reinforced SMA mixture had better
mechanical properties in comparison with control mixture.
Abstract: We present an Electronic Nose (ENose), which is
aimed at identifying the presence of one out of two gases, possibly
detecting the presence of a mixture of the two. Estimation of the
concentrations of the components is also performed for a volatile
organic compound (VOC) constituted by methanol and acetone, for
the ranges 40-400 and 22-220 ppm (parts-per-million), respectively.
Our system contains 8 sensors, 5 of them being gas sensors (of the
class TGS from FIGARO USA, INC., whose sensing element is a tin
dioxide (SnO2) semiconductor), the remaining being a temperature
sensor (LM35 from National Semiconductor Corporation), a
humidity sensor (HIH–3610 from Honeywell), and a pressure sensor
(XFAM from Fujikura Ltd.).
Our integrated hardware–software system uses some machine
learning principles and least square regression principle to identify at
first a new gas sample, or a mixture, and then to estimate the
concentrations. In particular we adopt a training model using the
Support Vector Machine (SVM) approach with linear kernel to teach
the system how discriminate among different gases. Then we apply
another training model using the least square regression, to predict
the concentrations.
The experimental results demonstrate that the proposed
multiclassification and regression scheme is effective in the
identification of the tested VOCs of methanol and acetone with
96.61% correctness. The concentration prediction is obtained with
0.979 and 0.964 correlation coefficient for the predicted versus real
concentrations of methanol and acetone, respectively.
Abstract: In this study two series of self compacting concrete
mixtures were prepared with 100% coarse recycled concrete
aggregates and different percentages of 0%, 20%, 40%, 60%, 80%
and 100% fine recycled concrete aggregates. In series I and II the
water to binder ratios were 0.50 and 0.45, respectively. The cement
content was kept 350
3 m
kg for those mixtures that don't have any
Nano-Silica. To improve the compressive strength of samples, Nano-
Silica replaced with 10% of cement weight in concrete mixtures. By
doing the tests, the results showed that, adding Nano-silica to the
samples with less percentage of fine recycled concrete aggregates,
lead to more increase on the compressive strength.
Abstract: Limited infrastructure development on peats and
organic soils is a serious geotechnical issues common to many
countries of the world especially Malaysia which distributed 1.5 mill
ha of those problematic soil. These soils have high water content and
organic content which exhibit different mechanical properties and
may also change chemically and biologically with time. Constructing
structures on peaty ground involves the risk of ground failure and
extreme settlement. Nowdays, much efforts need to be done in
making peatlands usable for construction due to increased landuse.
Deep mixing method employing cement as binders, is generally used
as measure again peaty/ organic ground failure problem. Where the
technique is widely adopted because it can improved ground
considerably in a short period of time. An understanding of
geotechnical properties as shear strength, stiffness and compressibility
behavior of these soils was requires before continues construction on
it. Therefore, 1- 1.5 meter peat soil sample from states of Johor and
an organic soil from Melaka, Malaysia were investigated. Cement
were added to the soil in the pre-mixing stage with water cement ratio
at range 3.5,7,14,140 for peats and 5,10,30 for organic soils,
essentially to modify the original soil textures and properties. The
mixtures which in slurry form will pour to polyvinyl chloride (pvc)
tube and cured at room temperature 250C for 7,14 and 28 days.
Laboratory experiments were conducted including unconfined
compressive strength and bender element , to monitor the improved
strength and stiffness of the 'stabilised mixed soils'. In between,
scanning electron miscroscopic (SEM) were observations to
investigate changes in microstructures of stabilised soils and to
evaluated hardening effect of a peat and organic soils stabilised
cement. This preliminary effort indicated that pre-mixing peat and
organic soils contributes in gaining soil strength while help the
engineers to establish a new method for those problematic ground
improvement in further practical and long term applications.
Abstract: Twenty seven tektites from the Wenchang area, Hainan
province (south China) and five tektites from the Khon Kaen area
(northeast Thailand) were analyzed for major and trace element
contents and Rb-Sr isotopic compositions. All the samples studied are
splash-form tektites. Tektites of this study are characterized by high
SiO2 contents ranging from 71.95 to 74.07 wt% which is consistent
with previously published analyses of Australasian tektites. The trace
element ratios Ba/Rb (avg. 3.89), Th/Sm (avg. 2.40), Sm/Sc (avg.
0.45), Th/Sc (avg. 0.99) and the rare earth elements (REE) contents of
tektites of this study are similar to the average upper continental crust.
Based on the chemical composition, it is suggested that tektites in this
study are derived from similar parental material and are similar to the
post-Archean upper crustal rocks. The major and trace element
abundances of tektites analyzed indicate that the parental material of
tektites may be a terrestrial sedimentary deposit. The tektites from the
Wenchang area, Hainan Island have high positive εSr(0)
values-ranging from 184.5~196.5 which indicate that the parental
material for these tektites have similar Sr isotopic compositions to old
terrestrial sedimentary rocks and they were not dominantly derived
from recent young sediments (such as soil or loess). Based on Rb-Sr
isotopic data, it has been suggested by Blum (1992) [1]that the
depositional age of sedimentary target materials is close to 170Ma
(Jurassic). According to the model suggested by Ho and Chen
(1996)[2], mixing calculations for various amounts and combinations
of target rocks have been carried out. We consider that the best fit for
tektites from the Wenchang area is a mixture of 47% shale, 23%
sandstone, 25% greywacke and 5% quartzite, and the other tektites
from Khon Kaen area is a mixture of 46% shale, 2% sandstone, 20%
greywacke and 32% quartzite.
Abstract: Group contribution based models are widely used in
industrial applications for its convenience and flexibility. Although a
number of group contribution models have been proposed, there were
certain limitations inherent to those models. Models based on group
contribution excess Gibbs free energy are limited to low pressures and
models based on equation of state (EOS) cannot properly describe
highly nonideal mixtures including acids without introducing
additional modification such as chemical theory. In the present study
new a new approach derived from quantum chemistry have been used
to calculate necessary EOS group interaction parameters. The
COSMO-RS method, based on quantum mechanics, provides a
reliable tool for fluid phase thermodynamics. Benefits of the group
contribution EOS are the consistent extension to hydrogen-bonded
mixtures and the capability to predict polymer-solvent equilibria up to
high pressures. The authors are confident that with a sufficient
parameter matrix the performance of the lattice EOS can be improved
significantly.
Abstract: In order to meet the limits imposed on automotive
emissions, engine control systems are required to constrain air/fuel
ratio (AFR) in a narrow band around the stoichiometric value, due to
the strong decay of catalyst efficiency in case of rich or lean mixture.
This paper presents a model of a sample spark ignition engine and
demonstrates Simulink-s capabilities to model an internal combustion
engine from the throttle to the crankshaft output. We used welldefined
physical principles supplemented, where appropriate, with
empirical relationships that describe the system-s dynamic behavior
without introducing unnecessary complexity. We also presents a PID
tuning method that uses an adaptive fuzzy system to model the
relationship between the controller gains and the target output
response, with the response specification set by desired percent
overshoot and settling time. The adaptive fuzzy based input-output
model is then used to tune on-line the PID gains for different
response specifications. Experimental results demonstrate that better
performance can be achieved with adaptive fuzzy tuning relative to
similar alternative control strategies. The actual response
specifications with adaptive fuzzy matched the desired response
specifications.
Abstract: An algorithm for learning an overcomplete dictionary
using a Cauchy mixture model for sparse decomposition of an underdetermined
mixing system is introduced. The mixture density
function is derived from a ratio sample of the observed mixture
signals where 1) there are at least two but not necessarily more
mixture signals observed, 2) the source signals are statistically
independent and 3) the sources are sparse. The basis vectors of the
dictionary are learned via the optimization of the location parameters
of the Cauchy mixture components, which is shown to be more
accurate and robust than the conventional data mining methods
usually employed for this task. Using a well known sparse
decomposition algorithm, we extract three speech signals from two
mixtures based on the estimated dictionary. Further tests with
additive Gaussian noise are used to demonstrate the proposed
algorithm-s robustness to outliers.
Abstract: Air infiltration in mass scale industrial applications of
bio char production is inevitable. The presence of oxygen during the
carbonization process is detrimental to the production of biochar yield
and properties. The experiment was carried out on several wood
species in a fixed-bed pyrolyser under various fractions of oxygen
ranging from 0% to 11% by varying nitrogen and oxygen composition
in the pyrolysing gas mixtures at desired compositions. The bed
temperature and holding time were also varied. Process optimization
was carried out by Response Surface Methodology (RSM) by
employing Central Composite Design (CCD) using Design Expert 6.0
Software. The effect of oxygen ratio and holding time on biochar yield
within the range studied were statistically significant. From the
analysis result, optimum condition of 15.2% biochar yield of
mangrove wood was predicted at pyrolysis temperature of 403 oC,
oxygen percentage of 2.3% and holding time of two hours. This
prediction agreed well with the experiment finding of 15.1% biochar
yield.
Abstract: Absorptive characteristics of polyaniline synthesized
in mixture of water and acetonitrile in 50/50 volume ratio was
studied. Synthesized polyaniline in powder shape is used as an
adsorbent to remove toxic hexavalent chromium from aqueous
solutions. Experiments were conducted in batch mode with different
variables such as agitation time, solution pH and initial concentration
of hexavalent chromium. Removal mechanism is the combination of
surface adsorption and reduction. The equilibrium time for removal
of Cr(T) and Cr(VI) was about 2 and 10 minutes respectively. The
optimum pH for total chromium removal occurred at pH 7 and
maximum hexavalent chromium removal took place under acidic
condition at pH 3. Investigating the isothermal characteristics showed
that the equilibrium adsorption data fitted both Freundlich-s and
Langmuir-s isotherms. The maximum adsorption of chromium was
calculated 36.1 mg/g for polyaniline
Abstract: In this study, effects of EGR on CO and HC emissions
of a dual fuel HCCI-DI engine are investigated. Tests were
conducted on a single-cylinder variable compression ratio (VCR)
diesel engine with compression ratio of 17.5. Premixed gasoline is
provided by a carburetor connected to intake manifold and equipped
with a screw to adjust premixed air-fuel ratio, and diesel fuel is
injected directly into the cylinder through an injector at pressure of
250 bars. A heater placed at inlet manifold is used to control the
intake charge temperature. Optimal intake charge temperature was
110-115ºC due to better formation of a homogeneous mixture
causing HCCI combustion. Timing of diesel fuel injection has a great
effect on stratification of in-cylinder charge in HCCI combustion.
Experiments indicated 35 BTDC as the optimum injection timing.
Coolant temperature was maintained 50ºC during the tests. Results
show that increasing engine speed at a constant EGR rate leads to
increase in CO and UHC emissions due to the incomplete
combustion caused by shorter combustion duration and less
homogeneous mixture. Results also show that increasing EGR
reduces the amount of oxygen and leads to incomplete combustion
and therefore increases CO emission due to lower combustion
temperature. HC emission also increases as a result of lower
combustion temperatures.
Abstract: The composite materials were prepared by sawdust, cassava starch and natural rubber latex (NR). The mixtures of 15%w/v gelatinized cassava starch and 15%w/v PVOH were used as the binder of these composite materials. The concentrated rubber latex was added to the mixtures. They were mixed rigorously to the treated sawdust in the ratio of 70:30 until achive uniform dispersion. The batters were subjected to the hot compression moulding at the temperature of 160°C and 3,000 psi pressure for 5 min. The experimental results showed that the mechanical properties of composite materials, which contained the gelatinized cassava starch and PVOH in the ratio of 2:1, 20% NR latex by weight of the dry starch and treated sawdust with 5%NaOH or 1% BPO, were the best. It contributed the maximal compression strength (341.10 + 26.11 N), puncture resistance (8.79 + 0.98 N/mm2) and flexural strength (3.99 + 0.72N/mm2). It is also found that the physicochemical and mechanical properties of composites strongly depends on the interface quality of sawdust, cassava starch and NR latex.
Abstract: The paper presents a method for multivariate time
series forecasting using Independent Component Analysis (ICA), as a preprocessing tool. The idea of this approach is to do the forecasting in the space of independent components (sources), and then to transform back the results to the original time series
space. The forecasting can be done separately and with a different
method for each component, depending on its time structure. The
paper gives also a review of the main algorithms for independent component analysis in the case of instantaneous mixture models, using second and high-order statistics. The method has been applied in simulation to an artificial multivariate time series
with five components, generated from three sources and a mixing matrix, randomly generated.
Abstract: Natural organic matter (NOM) is heterogeneous
mixture of organic compounds that enter the water media from
animal and plant remains, domestic and industrial wastes.
Researches showed that NOM is likely precursor material for
disinfection by products (DBPs). Chlorine very commenly used for
disinfection purposes and NOM and chlorine reacts then
Trihalomethane (THM) and Haloacetic acids (HAAs) which are
cancerogenics for human health are produced. The aim of the study is
to search NOM removal by enhanced coagulation from drinking
water source of Eskisehir which is supplied from Porsuk Dam.
Recently, Porsuk dam water is getting highly polluted and therefore
NOM concentration is increasing. Enhanced coagulation studies were
evaluated by measurement of Dissolved Organic Carbon (DOC), UV
absorbance at 254 nm (UV254), and different trihalomethane
formation potential (THMFP) tests. Results of jar test experiments
showed that NOM can be removed from water about 40-50 % of
efficiency by enhanced coagulation. Optimum coagulant type and
coagulant dosages were determined using FeCl3 and Alum.
Abstract: Reinforced Concrete (RC) structures strengthened
with fiber reinforced polymer (FRP) lack in thermal resistance under
elevated temperatures in the event of fire. This phenomenon led to
the lining of strengthened concrete with thin high performance
cementitious composites (THPCC) to protect the substrate against
elevated temperature. Elevated temperature effects on THPCC, based
on different cementitious materials have been studied in the past but
high-alumina cement (HAC)-based THPCC have not been well
characterized. This research study will focus on the THPCC based on
HAC replaced by 60%, 70%, 80% and 85% of ground granulated
blast furnace slag (GGBS). Samples were evaluated by the
measurement of their mechanical strength (28 & 56 days of curing)
after exposed to 400°C, 600°C and 28°C of room temperature for
comparison and corroborated by their microstructure study. Results
showed that among all mixtures, the mix containing only HAC
showed the highest compressive strength after exposed to 600°C as
compared to other mixtures. However, the tensile strength of THPCC
made of HAC and 60% GGBS content was comparable to the
THPCC with HAC only after exposed to 600°C. Field emission
scanning electron microscopy (FESEM) images of THPCC
accompanying Energy Dispersive X-ray (EDX) microanalysis
revealed that the microstructure deteriorated considerably after
exposure to elevated temperatures which led to the decrease in
mechanical strength.
Abstract: We measured the major and trace element contents
and Rb-Sr isotopic compositions of 12 tektites from the Maoming
area, Guandong province (south China). All the samples studied are
splash-form tektites which show pitted or grooved surfaces with
schlieren structures on some surfaces. The trace element ratios Ba/Rb
(avg. 4.33), Th/Sm (avg. 2.31), Sm/Sc (avg. 0.44), Th/Sc (avg. 1.01) ,
La/Sc (avg. 2.86), Th/U (avg. 7.47), Zr/Hf (avg. 46.01) and the rare
earth elements (REE) contents of tektites of this study are similar to the
average upper continental crust. From the chemical composition, it is
suggested that tektites in this study are derived from similar parental
terrestrial sedimentary deposit which may be related to post-Archean
upper crustal rocks. The tektites from the Maoming area have high
positive εSr(0) values-ranging from 176.9~190.5 which indicate that
the parental material for these tektites have similar Sr isotopic
compositions to old terrestrial sedimentary rocks and they were not
dominantly derived from recent young sediments (such as soil or
loess). The Sr isotopic data obtained by the present study support the
conclusion proposed by Blum et al. (1992)[1] that the depositional age
of sedimentary target materials is close to 170Ma (Jurassic). Mixing
calculations based on the model proposed by Ho and Chen (1996)[2]
for various amounts and combinations of target rocks indicate that the
best fit for tektites from the Maoming area is a mixture of 40% shale,
30% greywacke, 30% quartzite.
Abstract: In this paper, an algorithm for detecting and attenuating
puff noises frequently generated under the mobile environment is
proposed. As a baseline system, puff detection system is designed
based on Gaussian Mixture Model (GMM), and 39th Mel Frequency
Cepstral Coefficient (MFCC) is extracted as feature parameters. To
improve the detection performance, effective acoustic features for puff
detection are proposed. In addition, detected puff intervals are
attenuated by high-pass filtering. The speech recognition rate was
measured for evaluation and confusion matrix and ROC curve are used
to confirm the validity of the proposed system.