Abstract: This paper investigates the issue of building decision
trees from data with imprecise class values where imprecision is
encoded in the form of possibility distributions. The Information
Affinity similarity measure is introduced into the well-known gain
ratio criterion in order to assess the homogeneity of a set of
possibility distributions representing instances-s classes belonging to
a given training partition. For the experimental study, we proposed an
information affinity based performance criterion which we have used
in order to show the performance of the approach on well-known
benchmarks.
Abstract: This work presents a matched field processing (MFP)
algorithm based on Dopplerlet transform for estimating the motion
parameters of a sound source moving along a straight line and with a
constant speed by using a piecewise strategy, which can significantly
reduce the computational burden. Monte Carlo simulation results and
an experimental result are presented to verify the effectiveness of the
algorithm advocated.
Abstract: In this paper, creep constitutive equations of base
(Parent) and weld materials of the weldment for cold-drawn 304L
stainless steel have been obtained experimentally. For this purpose,
test samples have been generated from cold drawn bars and weld
material according to the ASTM standard. The creep behavior and
properties have been examined for these materials by conducting uniaxial
creep tests. Constant temperatures and constant load uni-axial
creep tests have been carried out at two high temperatures, 680 and
720 oC, subjected to constant loads, which produce initial stresses
ranging from 240 to 360 MPa. The experimental data have been used
to obtain the creep constitutive parameters using numerical
optimization techniques.
Abstract: In this study we applied thermal lens (TL) technique
to study the effect of size on thermal diffusivity of cadmium sulphide
(CdS) nanofluid prepared by using γ-radiation method containing
particles with different sizes. In TL experimental set up a diode laser
of wavelength 514 nm and intensity stabilized He-Ne laser were used
as the excitation source and the probe beam respectively,
respectively. The experimental results showed that the thermal
diffusivity value of CdS nanofluid increases when the of particle size
increased.
Abstract: This paper presents the results of the preliminary investigation of microwave (MW) irradiation pretreatments on the anaerobic digestion of food residues using biochemical methane potential (BMP) assays. Low solids systems with a total solids (TS) content ranging from 5.0-10.0% were analyzed. The inoculum to bulk mass of substrates to water ratio was 1:2:2 (mass basis). The experimental conditions for pretreatments were as follows: a control (no MW irradiation), two runs with MW irradiation for 15 and 30 minutes at 320 W, and another two runs with MW irradiation at 528 W for 30 and 60 minutes. The cumulative biogas production were 6.3 L and 8.7 L for 15min/320 W and 30min/320 W MW irradiation conditions, respectively, and 10.5 L and 11.4 L biogas for 30min/528 W and 60min/528 W, respectively, as compared to the control giving 5.8 L biogas. Both an increase in exposure time of irradiation and power of MW had increased the rate and yield of biogas. Singlefactor ANOVA tests (p
Abstract: Information is increasing in volumes; companies are overloaded with information that they may lose track in getting the intended information. It is a time consuming task to scan through each of the lengthy document. A shorter version of the document which contains only the gist information is more favourable for most information seekers. Therefore, in this paper, we implement a text summarization system to produce a summary that contains gist information of oil and gas news articles. The summarization is intended to provide important information for oil and gas companies to monitor their competitor-s behaviour in enhancing them in formulating business strategies. The system integrated statistical approach with three underlying concepts: keyword occurrences, title of the news article and location of the sentence. The generated summaries were compared with human generated summaries from an oil and gas company. Precision and recall ratio are used to evaluate the accuracy of the generated summary. Based on the experimental results, the system is able to produce an effective summary with the average recall value of 83% at the compression rate of 25%.
Abstract: As a result of urbanization, the unpredictable growth of industry and transport, production of chemicals, military activities, etc. the concentration of anthropogenic toxicants spread in nature exceeds all the permissible standards. Most dangerous among these contaminants are organic compounds having great persistence, bioaccumulation, and toxicity along with our awareness of their prominent occurrence in the environment and food chain. Among natural ecological tools, plants still occupying above 40% of the world land, until recently, were considered as organisms having only a limited ecological potential, accumulating in plant biomass and partially volatilizing contaminants of different structure. However, analysis of experimental data of the last two decades revealed the essential role of plants in environment remediation due to ability to carry out intracellular degradation processes leading to partial or complete decomposition of carbon skeleton of different structure contaminants. Though, phytoremediation technologies still are in research and development, their various applications have been successfully used. The paper aims to analyze mechanisms of organic contaminants uptake and detoxification in plants, being the less studied issue in evaluation and exploration of plants potential for environment remediation.
Abstract: In this paper, a tooth shape optimization method for
cogging torque reduction in Permanent Magnet (PM) motors is
developed by using the Reduced Basis Technique (RBT) coupled by
Finite Element Analysis (FEA) and Design of Experiments (DOE)
methods. The primary objective of the method is to reduce the
enormous number of design variables required to define the tooth
shape. RBT is a weighted combination of several basis shapes. The
aim of the method is to find the best combination using the weights
for each tooth shape as the design variables. A multi-level design
process is developed to find suitable basis shapes or trial shapes at
each level that can be used in the reduced basis technique. Each level
is treated as a separated optimization problem until the required
objective – minimum cogging torque – is achieved. The process is
started with geometrically simple basis shapes that are defined by
their shape co-ordinates. The experimental design of Taguchi method
is used to build the approximation model and to perform
optimization. This method is demonstrated on the tooth shape
optimization of a 8-poles/12-slots PM motor.
Abstract: Due to the ever growing amount of publications about
protein-protein interactions, information extraction from text is
increasingly recognized as one of crucial technologies in
bioinformatics. This paper presents a Protein Interaction Extraction
System using a Link Grammar Parser from biomedical abstracts
(PIELG). PIELG uses linkage given by the Link Grammar Parser to
start a case based analysis of contents of various syntactic roles as
well as their linguistically significant and meaningful combinations.
The system uses phrasal-prepositional verbs patterns to overcome
preposition combinations problems. The recall and precision are
74.4% and 62.65%, respectively. Experimental evaluations with two
other state-of-the-art extraction systems indicate that PIELG system
achieves better performance. For further evaluation, the system is
augmented with a graphical package (Cytoscape) for extracting
protein interaction information from sequence databases. The result
shows that the performance is remarkably promising.
Abstract: Reliability is one of the most important quality attributes of software. Based on the approach of Reussner and the approach of Cheung, we proposed the reliability prediction model of component-based software architectures. Also, the value of the model is shown through the experimental evaluation on a web server system.
Abstract: In the current research, neuro-fuzzy model and regression model was developed to predict Material Removal Rate in Electrical Discharge Machining process for AISI D2 tool steel with copper electrode. Extensive experiments were conducted with various levels of discharge current, pulse duration and duty cycle. The experimental data are split into two sets, one for training and the other for validation of the model. The training data were used to develop the above models and the test data, which was not used earlier to develop these models were used for validation the models. Subsequently, the models are compared. It was found that the predicted and experimental results were in good agreement and the coefficients of correlation were found to be 0.999 and 0.974 for neuro fuzzy and regression model respectively
Abstract: This paper presents the experimental results of silicone rubber polymer insulators for 22 kV systems under salt water dip wheel test based on IEC 62217. Straight shed silicone rubber polymer insulators having leakage distance 685 mm were tested continuously 30,000 cycles. One test cycle includes 4 positions, energized, de-energized, salt water dip and deenergized, respectively. For one test cycle, each test specimen remains stationary for about 40 second in each position and takes 8 second for rotate to next position. By visual observation, sever surface erosion was observed on the trunk near the energized end of tested specimen. Puncture was observed on the upper shed near the energized end. In addition, decreasing in hydrophobicity and increasing in hardness were measured on tested specimen comparing with new specimen. Furthermore, chemical analysis by ATR-FTIR was conducted in order to elucidate the chemical change of tested specimens comparing with new specimen.
Abstract: Basic objective of this study is to create a regression
analysis method that can estimate the length of a plastic hinge which
is an important design parameter, by making use of the outcomes of
(lateral load-lateral displacement hysteretic curves) the experimental
studies conducted for the reinforced square concrete columns. For
this aim, 170 different square reinforced concrete column tests results
have been collected from the existing literature. The parameters
which are thought affecting the plastic hinge length such as crosssection
properties, features of material used, axial loading level,
confinement of the column, longitudinal reinforcement bars in the
columns etc. have been obtained from these 170 different square
reinforced concrete column tests. In the study, when determining the
length of plastic hinge, using the experimental test results, a
regression analysis have been separately tested and compared with
each other. In addition, the outcome of mentioned methods on
determination of plastic hinge length of the reinforced concrete
columns has been compared to other methods available in the
literature.
Abstract: We have developed a microfluidic device system for the continuous producting of nanoparticles, and we have clarified the relationship between the mixing performance of reactors and the particle size. First, we evaluated the mixing performance of reactors by carring out the Villermaux–Dushman reaction and determined the experimental conditions for producing AgCl nanoparticles. Next, we produced AgCl nanoparticles and evaluated the mixing performance and the particle size. We found that as the mixing performance improves the size of produced particles decreases and the particle size distribution becomes sharper. We produced AgCl nanoparticles with a size of 86 nm using the microfluidic device that had the best mixing performance among the three reactors we tested in this study; the coefficient of variation (Cv) of the size distribution of the produced nanoparticles was 26.1%.
Abstract: The purpose of research was to know the role of
immunogenic protein of 49 kDa from V.alginolyticus which capable
to initiate molecule expression of MHC Class II in receptor of
Cromileptes altivelis. The method used was in vivo experimental
research through testing of immunogenic protein 49 kDa from
V.alginolyticus at Cromileptes altivelis (size of 250 - 300 grams)
using 3 times booster by injecting an immunogenic protein in a
intramuscular manner. Response of expressed MHC molecule was
shown using immunocytochemistry method and SEM. Results
indicated that adhesin V.alginolyticus 49 kDa which have
immunogenic character could trigger expression of MHC class II on
receptor of grouper and has been proven by staining using
immunocytochemistry and SEM with labeling using antibody anti
MHC (anti mouse). This visible expression based on binding between
epitopes antigen and antibody anti MHC in the receptor. Using
immunocytochemistry, intracellular response of MHC to in vivo
induction of immunogenic adhesin from V.alginolyticus was shown.
Abstract: In this paper, we propose an algorithm to compute
initial cluster centers for K-means clustering. Data in a cell is
partitioned using a cutting plane that divides cell in two smaller cells.
The plane is perpendicular to the data axis with the highest variance
and is designed to reduce the sum squared errors of the two cells as
much as possible, while at the same time keep the two cells far apart
as possible. Cells are partitioned one at a time until the number of
cells equals to the predefined number of clusters, K. The centers of
the K cells become the initial cluster centers for K-means. The
experimental results suggest that the proposed algorithm is effective,
converge to better clustering results than those of the random
initialization method. The research also indicated the proposed
algorithm would greatly improve the likelihood of every cluster
containing some data in it.
Abstract: In the present study, a heterogeneous and
homogeneous gas flow dispersion model for simulation and
optimisation of a large-scale catalytic slurry reactor for the direct
synthesis of dimethyl ether (DME) from syngas and CO2, using a
churn-turbulent regime was developed. In the heterogeneous gas flow
model the gas phase was distributed into two bubble phases: small
and large, however in the homogeneous one, the gas phase was
distributed into only one large bubble phase. The results indicated
that the heterogeneous gas flow model was in more agreement with
experimental pilot plant data than the homogeneous one.
Abstract: Results are presented from a combined experimental
and modeling study undertaken to understand the effect of fuel spray
angle on soot production in turbulent liquid spray flames. The
experimental work was conducted in a cylindrical laboratory furnace
at fuel spray cone angle of 30º, 45º and 60º. Soot concentrations
inside the combustor are measured by filter paper technique. The soot
concentration is modeled by using the soot particle number density
and the mass density based acetylene concentrations. Soot oxidation
occurred by both hydroxide radicals and oxygen molecules. The
comparison of calculated results against experimental measurements
shows good agreement. Both the numerical and experimental results
show that the peak value of soot and its location in the furnace
depend on fuel spray cone angle. An increase in spray angle enhances
the evaporating rate and peak temperature near the nozzle. Although
peak soot concentration increase with enhance of fuel spray angle but
soot emission from the furnace decreases.
Abstract: With the development of the Internet, E-commerce is
growing at an exponential rate, and lots of online stores are built up to
sell their goods online. A major factor influencing the successful
adoption of E-commerce is consumer-s trust. For new or unknown
Internet business, consumers- lack of trust has been cited as a major
barrier to its proliferation. As web sites provide key interface for
consumer use of E-Commerce, we investigate the design of web site to
build trust in E-Commerce from a design science approach. A
conceptual model is proposed in this paper to describe the ontology of
online transaction and human-computer interaction. Based on this
conceptual model, we provide a personalized webpage design
approach using Bayesian networks learning method. Experimental
evaluation are designed to show the effectiveness of web
personalization in improving consumer-s trust in new or unknown
online store.
Abstract: Silver nano-particles have been used for antibacterial
purpose and it is also believed to have removal of odorous compounds,
oxidation capacity as a metal catalyst. In this study, silver
nano-particles in nano sizes (5-30 nm) were prepared on the surface of
NaHCO3, the supporting material, using a sputtering method that
provided high silver content and minimized conglomerating problems
observed in the common AgNO3 photo-deposition method. The silver
nano-particles were dispersed by dissolving Ag-NaHCO3 into water,
and the dispersed silver nano-particles in the aqueous phase were
applied to remove inorganic odor compounds, H2S, in a scrubbing
reactor. Hydrogen sulfide in the gas phase was rapidly removed by the
silver nano-particles, and the concentration of sulfate (SO4
2-) ion
increased with time due to the oxidation reaction by silver as a
catalyst. Consequently, the experimental results demonstrated that the
silver nano-particles in the aqueous solution can be successfully
applied to remove odorous compounds without adding additional
energy sources and producing any harmful byproducts