Abstract: In recent times there has been a growing interest in the
development of quasi-two-dimensional niobium pentoxide (Nb2O5)
as a semiconductor for the potential electronic applications such as
capacitors, filtration, dye-sensitised solar cells and gas sensing
platforms. Therefore once the purpose is established, Nb2O5 can be
prepared in a number of nano- and sub-micron-structural
morphologies that include rods, wires, belts and tubes. In this study
films of Nb2O5 were prepared on gold plated silicon substrate using
spin-coating technique and subsequently by mechanical exfoliation.
The reason this method was employed was to achieve layers of less
than 15nm in thickness. The sintering temperature of the specimen
was 800oC. The morphology and structural characteristics of the
films were analyzed by Atomic Force Microscopy (AFM), Raman
Spectroscopy, X-ray Photoelectron Spectroscopy (XPS).
Abstract: We fabricated multi-walled carbon nanotube (MCNT)
emitters by an electroporetic deposition (EPD) method using a
MCNT-sodium dodecyl sulfate (SDS) suspension. MCNT films were
prepared on graphite tip using EPD. We observe field emission
properties of MCNT film after heat treatment. Consequently, The
MCNT film on graphite tip exhibit good electron emission current.
Abstract: The purpose of this study was to investigate the
response of the newly released Gafchromic HD-V2 film for alpha
particle of 5.5 MeV. Gafchromic HD-V2 was exposed to alpha
particles of energy 5 MeV from 241Am for different durations. Then
the films were scanned with a flatbed scanner. The dose response
curve up to 2200 Gy has been achieved. The film’s reproducibility
and sensitivity were evaluated. The results obtained show that the net
optical density increases almost exponentially with the increase in the
exposure time, and it becomes saturated after prolonged exposure
times. The red channel shows the highest sensitivity, with a value of
4 x 10-3 Gy-1 at netOD of 0.4. The inter-film reproducibility was
measured and the relative uncertainty found was 1.7 %, 2.1 % and 2.3
% for grey, red and green channels, respectively.
Abstract: This paper studies, maps and explains the interactions between downloaders and uploaders pertaining to the Internet film piracy. This study also covers several motivational factors that influence users to upload or download movies, and thus to engage in film piracy over the Internet. The essay also proposes a model that describes user behavior including their relationships and influences. Moreover, proposed theoretical interactions and motivational factors are applied to the real world scenario, using examples of a data storage webpage server Ulozto.net and webpage Piratebay.org gathering information about downloadable BitTorrents. Moreover, the theory is further supported by description of behavior of real Internet uploaders.
Abstract: Sol-gel method has been used to fabricate
nanocomposite films on glass substrates composed halloysite clay
mineral and nanocrystalline TiO2. The methodology for the synthesis
involves a simple chemistry method utilized nonionic surfactant
molecule as pore directing agent along with the acetic acid-based solgel
route with the absence of water molecules. The thermal treatment
of composite films at 450oC ensures elimination of organic material
and lead to the formation of TiO2 nanoparticles onto the surface of
the halloysite nanotubes. Microscopy techniques and porosimetry
methods used in order to delineate the structural characteristics of the
materials. The nanocomposite films produced have no cracks and
active anatase crystal phase with small crystallite size were deposited
on halloysite nanotubes. The photocatalytic properties for the new
materials were examined for the decomposition of the Basic Blue 41
azo dye in solution. These, nanotechnology based composite films
show high efficiency for dye’s discoloration in spite of different
halloysite quantities and small amount of halloysite/TiO2 catalyst
immobilized onto glass substrates. Moreover, we examined the
modification of the halloysite/TiO2 films with silver particles in order
to improve the photocatalytic properties of the films. Indeed, the
presence of silver nanoparticles enhances the discoloration rate of the
Basic Blue 41 compared to the efficiencies obtained for unmodified
films.
Abstract: In this paper, we proposed the effects of Mo thickness
on the properties of AZO/Mo/AZO multilayer thin films for
opto-electronics applications. The structural, optical and electrical
properties of AZO/Mo/AZO thin films were investigated.
Optimization of the thin films coatings resulted with low resistivity of
9.98 × 10-5 )-cm, mobility of 12.75 cm2/V-s, carrier concentration of
1.05 × 1022 cm-3, maximum transmittance of 79.13% over visible
spectrum of 380 – 780 nm and Haacke figure of merit (FOM) are 5.95
× 10-2 )-1 under Mo layer thickness of 15 nm. These results indicate an
alternative candidate for use as a transparent electrode in solar cells
and various displays applications.
Abstract: ZnO+Ga2O3 functionally graded thin films (FGTFs)
were examined for their potential use as Solar cell and organic light
emitting diodes (OLEDs). FGTF transparent conducting oxides (TCO)
were fabricated by combinatorial RF magnetron sputtering. The
composition gradient was controlled up to 10% by changing the
plasma power of the two sputter guns. A Ga2O3+ZnO graded region
was placed on the top layer of ZnO. The FGTFs showed up to 80%
transmittance. Their surface resistances were reduced to < 10% by
increasing the Ga2O3: pure ZnO ratio in the TCO. The FGTFs- work
functions could be controlled within a range of 0.18 eV. The
controlled work function is a very promising technology because it
reduces the contact resistance between the anode and Hall transport
layers of OLED and solar cell devices.
Abstract: Recently, nanomaterials are developed in the form of nano-films, nano-crystals and nano-pores. Lanthanide phosphates as a material find extensive application as laser, ceramic, sensor, phosphor, and also in optoelectronics, medical and biological labels, solar cells and light sources. Among the different kinds of rare-earth orthophosphates, yttrium orthophosphate has been shown to be an efficient host lattice for rare earth activator ions, which have become a research focus because of their important role in the field of light display systems, lasers, and optoelectronic devices. It is in this context that the 4fn- « 4fn-1 5d transitions of rare earth in insulating materials, lying in the UV and VUV, are the aim of large number of studies .Though there has been a few reports on Eu3+, Nd3+, Pr3+,Er3+, Ce3+, Tm3+ doped YPO4. The 4fn- « 4fn-1 5d transitions of the rare earth dependent to the host-matrix, several matrices ions were used to study these transitions, in this work we are suggesting to study on a very specific class of inorganic material that are orthophosphate doped with rare earth ions. This study focused on the effect of Ce3+ concentration on the structural and optical properties of Ce3+ doped YPO4 yttrium orthophosphate with powder form prepared by the Sol Gel method.
Abstract: Tungsten trioxide has been prepared by using P-PTA
as a precursor on alumina substrates by spin coating method.
Palladium introduced on WO3 film via electrolysis deposition by
using palladium chloride as catalytic precursor. The catalytic
precursor was introduced on the series of films with different
morphologies. X-ray diffractometry (XRD), Scanning electron
microscopy (SEM) and XPS were applied to analyze structure and
morphology of the fabricated thin films. Then we measured variation
of samples- electrical conductivity of pure and Pd added films in air
and diluted hydrogen. Addition of Pd resulted in a remarkable
improvement of the hydrogen sensing properties of WO3 by detection
of Hydrogen below 1% at room temperature. Also variation of the
electrical conductivity in the presence of diluted hydrogen revealed
that response of samples depends rather strongly on the palladium
configuration on the surface.
Abstract: Group-III nitride material as particularly AlxGa1-xN is
one of promising optoelectronic materials to require for shortwavelength
devices. To achieve the high-quality AlxGa1-xN films for
a high performance of such devices, AlN-nucleation layers are the
important factor. To improve the AlN-nucleation layers with a
variation of Ga-addition, XRD measurements were conducted to
analyze the crystalline quality of the subsequent Al0.1Ga0.9N with the
minimum ω-FWHMs of (0002) and (10-10) reflections of 425 arcsec
and 750 arcsec, respectively. SEM and AFM measurements were
performed to observe the surface morphology and TEM
measurements to identify the microstructures and orientations.
Results showed that the optimized Ga-atoms in the Al(Ga)Nnucleation
layers improved the surface diffusion to form moreuniform
crystallites in structure and size, better alignment of each
crystallite, and better homogeneity of island distribution. This, hence,
improves the orientation of epilayers on the Si-surface and finally
improves the crystalline quality and reduces the residual strain of
subsequent Al0.1Ga0.9N layers.
Abstract: In turning hardened steel, polycrystalline cubic boron
nitride (cBN) compacts are widely used, due to their higher hardness
and higher thermal conductivity. However, in milling hardened steel,
fracture of cBN cutting tools readily occurs because they have poor
fracture toughness. Therefore, coated cemented carbide tools, which
have good fracture toughness and wear resistance, are generally
widely used. In this study, hardened steel (ASTM D2, JIS SKD11,
60HRC) was milled with three physical vapor deposition
(PVD)-coated cemented carbide end mill cutters in order to determine
effective tool materials for cutting hardened steel at high cutting
speeds. The coating films used were (Ti,W)N/(Ti,W,Si)N and
(Ti,W)N/(Ti,W,Si,Al)N coating films. (Ti,W,Si,Al)N is a new type of
coating film. The inner layer of the (Ti,W)N/(Ti,W,Si)N and
(Ti,W)N/(Ti,W,Si,Al)N coating system is (Ti,W)N coating film, and
the outer layer is (Ti,W,Si)N and (Ti,W,Si,Al)N coating films,
respectively. Furthermore, commercial (Ti,Al)N-based coating film
was also used. The following results were obtained: (1) In milling
hardened steel at a cutting speed of 3.33 m/s, the tool wear width of the
(Ti,W)N/(Ti,W,Si,Al)N-coated tool was smaller than that of the
(Ti,W)N/(Ti,W,Si)N-coated tool. And, compared with the commercial
(Ti,Al)N, the tool wear width of the (Ti,W)N/(Ti,W,Si,Al)N-coated
tool was smaller than that of the (Ti,Al)N-coated tool. (2) The tool
wear of the (Ti,W)N/(Ti,W,Si,Al)N-coated tool increased with an
increase in cutting speed. (3) The (Ti,W)N/(Ti,W,Si,Al)N-coated
cemented carbide was an effective tool material for high-speed cutting
below a cutting speed of 3.33 m/s.
Abstract: The morphological parameter of a thin film surface
can be characterized by power spectral density (PSD) functions
which provides a better description to the topography than the RMS
roughness and imparts several useful information of the surface
including fractal and superstructure contributions. Through the
present study Nanoparticle copper/carbon composite films were
prepared by co-deposition of RF-Sputtering and RF-PECVD method
from acetylene gas and copper target. Surface morphology of thin
films is characterized by using atomic force microscopy (AFM). The
Carbon content of our films was obtained by Rutherford Back
Scattering (RBS) and it varied from .4% to 78%. The power values of
power spectral density (PSD) for the AFM data were determined by
the fast Fourier transform (FFT) algorithms. We investigate the effect
of carbon on the roughness of thin films surface. Using such
information, roughness contributions of the surface have been
successfully extracted.