Abstract: The estimation of overall on-site and off-site greenhouse gas (GHG) emissions by wastewater treatment plants revealed that in anaerobic and hybrid treatment systems greater emissions result from off-site processes compared to on-site processes. However, in aerobic treatment systems, onsite processes make a higher contribution to the overall GHG emissions. The total GHG emissions were estimated to be 1.6, 3.3 and 3.8 kg CO2-e/kg BOD in the aerobic, anaerobic and hybrid treatment systems, respectively. In the aerobic treatment system without the recovery and use of the generated biogas, the off-site GHG emissions were 0.65 kg CO2-e/kg BOD, accounting for 40.2% of the overall GHG emissions. This value changed to 2.3 and 2.6 kg CO2-e/kg BOD, and accounted for 69.9% and 68.1% of the overall GHG emissions in the anaerobic and hybrid treatment systems, respectively. The increased off-site GHG emissions in the anaerobic and hybrid treatment systems are mainly due to material usage and energy demand in these systems. The anaerobic digester can contribute up to 100%, 55% and 60% of the overall energy needs of plants in the aerobic, anaerobic and hybrid treatment systems, respectively.
Abstract: Accurate timing alignment and stability is important
to maximize the true counts and minimize the random counts in
positron emission tomography So signals output from detectors must
be centering with the two isotopes to pre-operation and fed signals
into four units of pulse-processing units, each unit can accept up to
eight inputs. The dual source computed tomography consist two units
on the left for 15 detector signals of Cs-137 isotope and two units on
the right are for 15 detectors signals of Co-60 isotope. The gamma
spectrum consisting of either single or multiple photo peaks. This
allows for the use of energy discrimination electronic hardware
associated with the data acquisition system to acquire photon counts
data with a specific energy, even if poor energy resolution detectors
are used. This also helps to avoid counting of the Compton scatter
counts especially if a single discrete gamma photo peak is emitted by
the source as in the case of Cs-137. In this study the polyenergetic
version of the alternating minimization algorithm is applied to the
dual energy gamma computed tomography problem.
Abstract: A robust AUSM+ upwind discretisation scheme has been developed to simulate multiphase flow using consistent spatial discretisation schemes and a modified low-Mach number diffusion term. The impact of the selection of an interfacial pressure model has also been investigated. Three representative test cases have been simulated to evaluate the accuracy of the commonly-used stiffenedgas equation of state with respect to the IAPWS-IF97 equation of state for water. The algorithm demonstrates a combination of robustness and accuracy over a range of flow conditions, with the stiffened-gas equation tending to overestimate liquid temperature and density profiles.
Abstract: The aim of this study is to develop a cost-effective WBGT heat stress monitor which provides precise heat stress measurement. The proposed device employs SHT15 and DS18B20 as a temperature and humidity sensors, respectively, incorporating with ATmega328 microcontroller. The developed heat stress monitor was calibrated and adjusted to that of the standard temperature and humidity sensors in the laboratory. The results of this study illustrated that the mean percentage error and the standard deviation from the measurement of the globe temperature was 2.33 and 2.71 respectively, while 0.94 and 1.02 were those of the dry bulb temperature, 0.79 and 0.48 were of the wet bulb temperature, and 4.46 and 1.60 were of the relative humidity sensor. This device is relatively low-cost and the measurement error is acceptable.
Abstract: Raisin Concentrate (RC) are the most important
products obtained in the raisin processing industries. These RC
products are now used to make the syrups, drinks and confectionery
productions and introduced as natural substitute for sugar in food
applications. Iran is a one of the biggest raisin exporter in the world
but unfortunately despite a good raw material, no serious effort to
extract the RC has been taken in Iran. Therefore, in this paper, we
determined and analyzed affected parameters on extracting RC
process and then optimizing these parameters for design the
extracting RC process in two types of raisin (round and long)
produced in Khorasan region. Two levels of solvent (1:1 and 2:1),
three levels of extraction temperature (60°C, 70°C and 80°C), and
three levels of concentration temperature (50°C, 60°C and 70°C)
were the treatments. Finally physicochemical characteristics of the
obtained concentrate such as color, viscosity, percentage of reduction
sugar, acidity and the microbial tests (mould and yeast) were
counted. The analysis was performed on the basis of factorial in the
form of completely randomized design (CRD) and Duncan's multiple
range test (DMRT) was used for the comparison of the means.
Statistical analysis of results showed that optimal conditions for
production of concentrate is round raisins when the solvent ratio was
2:1 with extraction temperature of 60°C and then concentration
temperature of 50°C. Round raisin is cheaper than the long one, and
it is more economical to concentrate production. Furthermore, round
raisin has more aromas and the less color degree with increasing the
temperature of concentration and extraction. Finally, according to
mentioned factors the concentrate of round raisin is recommended.
Abstract: Reinforced concrete has good durability and excellent structural performance. But there are cases of early deterioration due to a number of factors, one prominent factor being corrosion of steel reinforcement. The process of corrosion sets in due to ingress of moisture, oxygen and other ingredients into the body of concrete, which is unsound, permeable and absorbent. Cracks due to structural and other causes such as creep, shrinkage, etc also allow ingress of moisture and other harmful ingredients and thus accelerate the rate of corrosion. There are several interactive factors both external and internal, which lead to corrosion of reinforcement and ultimately failure of structures. Suitable addition of mineral admixture like silica fume (SF) in concrete improves the strength and durability of concrete due to considerable improvement in the microstructure of concrete composites, especially at the transition zone. Secondary reinforcement in the form of fibre is added to concrete, which provides three dimensional random reinforcement in the entire mass of concrete. Reinforced concrete beams of size 0.1 m X 0.15 m and length 1m have been cast using M 35 grade of concrete. The beams after curing process were subjected to corrosion process by impressing an external Direct Current (Galvanostatic Method) for a period of 15 days under stressed and unstressed conditions. The corroded beams were tested by applying two point loads to determine the ultimate load carrying capacity and cracking pattern and the results of specimens were compared with that of the companion specimens. Gravimetric method is used to quantify corrosion that has occurred.
Abstract: In this article a bibliography research takes place to
track down and introduce the barriers and opportunities for the
adoption of e-Governance services mainly from the side of citizen,
that is to say, the demand side. Although governments invest
continuously in producing of e-Governance services, citizens face
difficulties to adopt these services. Barriers derive and prevent them
from using e-Governance services. Barrier is anything preventing
citizens from the adoption of e-Governance services. Barriers impede
or do not allow the adoption of e-Governance services by the
citizens. If the barriers are pinpointed, it will be possible to take them
into consideration while designing e-Governance services which the
citizens are likely to use, if the obstacles are raised. The barriers will
thus be converted in opportunities that will facilitate the adoption.
Abstract: Conventional materials like glass, wood or metals
replacement with polymer materials is still continuing. More simple
thus cheaper production is the main reason. However due to high
energy and petrochemical prices are polymer prices increasing too.
That´s why various kinds of fillers are used to make polymers
cheaper. Of course target is to maintain or improve properties of
these compounds. In this paper are solved rheology issues of
polymers compounded with vegetal origin fibers.
Abstract: A green design for assembly model is presented to
integrate design evaluation and assembly and disassembly sequence
planning by evaluating the three activities in one integrated model. For
an assembled product, an assembly sequence planning model is
required for assembling the product at the start of the product life cycle.
A disassembly sequence planning model is needed for disassembling
the product at the end. In a green product life cycle, it is important to
plan how a product can be disassembled, reused, or recycled, before
the product is actually assembled and produced. Given a product
requirement, there may be several design alternative cases to design
the same product. In the different design cases, the assembly and
disassembly sequences for producing the product can be different. In
this research, a new model is presented to concurrently evaluate the
design and plan the assembly and disassembly sequences. First, the
components are represented by using graph based models. Next, a
particle swarm optimization (PSO) method with a new encoding
scheme is developed. In the new PSO encoding scheme, a particle is
represented by a position matrix defining an assembly sequence and a
disassembly sequence. The assembly and disassembly sequences can
be simultaneously planned with an objective of minimizing the total of
assembly costs and disassembly costs. The test results show that the
presented method is feasible and efficient for solving the integrated
design evaluation and assembly and disassembly sequence planning
problem. An example product is implemented and illustrated in this
paper.
Abstract: Dynamic models of power converters are normally
time-varying because of their switching actions. Several approaches
are applied to analyze the power converters to achieve the timeinvariant
models suitable for system analysis and design via the
classical control theory. The paper presents how to derive dynamic
models of the power system consisting of a three-phase controlled
rectifier feeding an uncontrolled buck converter by using the
combination between the well known techniques called the DQ and
the generalized state-space averaging methods. The intensive timedomain
simulations of the exact topology model are used to support
the accuracies of the reported model. The results show that the
proposed model can provide good accuracies in both transient and
steady-state responses.
Abstract: This paper provides a new approach to solve the motion planning problems of flying robots in uncertain 3D dynamic environments. The robots controlled by this method can adaptively choose the fast way to avoid collision without information about the shapes and trajectories of obstacles. Based on sphere coordinates the new method accomplishes collision avoidance of flying robots without any other auxiliary positioning systems. The Self-protection System gives robots self-protection abilities to work in uncertain 3D dynamic environments. Simulations illustrate the validity of the proposed method.
Abstract: Yogurts are prepared by fermenting milk with bacterial cultures consisting of a mixture of Streptococcus ssp. thermophilus and Lactobacillus delbrueckii ssp. bulgaricus. The main aim of this investigation was to develop a majority goat yogurt, with the addition of sheep milk in order to have a final product with good physicochemical quality properties and sensorial attributes. Four types of yogurts were prepared presenting the following proportion of goat and sheep milk respectively: C100 – 100%; C80 – 80%/20%; C60 – 60%/40%; C50 – 50%/50%. The goat milk was from the Serrana Jarmelista breed and the sheep milk from the Serra da Estrela breed. The inclusion of sheep milk improved attractiveness to consumers, and it also improved the nutritional value of the product, mainly the fatty acid and mineral contents. The C50 yogurt was preferred by 28% of the panellists, followed by the C100 with 16% and the commercial cow yogurt was 40% of preferences.
Abstract: A mathematical model for the hydrodynamics of a
surface water treatment pilot plant was developed and validated by
the determination of the residence time distribution (RTD) for the
main equipments of the unit. The well known models of ideal/real
mixing, ideal displacement (plug flow) and (one-dimensional axial)
dispersion model were combined in order to identify the structure
that gives the best fitting of the experimental data for each equipment
of the pilot plant. RTD experimental results have shown that pilot
plant hydrodynamics can be quite well approximated by a
combination of simple mathematical models, structure which is
suitable for engineering applications. Validated hydrodynamic
models will be further used in the evaluation and selection of the
most suitable coagulation-flocculation reagents, optimum operating
conditions (injection point, reaction times, etc.), in order to improve
the quality of the drinking water.
Abstract: In this study, oxidative steam reforming of methanol (OSRM) over a Au/CeO2–Fe2O3 catalyst prepared by a depositionprecipitation (DP) method was studied to produce hydrogen in order to feed a Proton Exchange Membrane Fuel Cell (PEMFC). The support (CeO2, Fe2O3, and CeO2–Fe2O3) were prepared by precipitation and co-precipitation methods. The impact of the support composition on the catalytic performance was studied by varying the Ce/(Ce+Fe) atomic ratio, it was found that the 1%Au/CF(0.25) calcined at 300 °C exhibited the highest catalytic activity in the whole temperature studied. In addition, the effect of Au content was investigated and 3%Au/CF(0.25) exhibited the highest activity under the optimum condition in the temperature range of 200 °C to 400 °C. The catalysts were characterized by various techniques: XRD, TPR, XRF, and UV-vis.
Abstract: The study investigates the relationship between
education level, workplace learning behaviors, psychological
empowerment and burnout in a sample of 191 teachers. We
hypothesized that education level will positively affect psychological
state of increased empowerment and decreased burnout, and we
purposed that these effects will be mediated by workplace learning
behaviors. We used multiple regression analyses to test the model
that included also the 6 following control variables: The teachers'
age, gender, and teaching tenure; the schools' religious level, the
pupils' needs: regular/ special needs, and the class level: elementary/
high school. The results support the purposed mediating model.
Abstract: Postmenopausal osteoporosis is a disorder
characterized by the progressive bone loss induced by estrogen
deficiency in postmenopausal women. This imbalance affects
calcium–phosphate metabolism and results in secondary
hyperparathyroidism. Purariae Radix (PR), the root of P. lobata
(Wild.) Ohwi, is one of the earliest medicinal herbs employed in
ancient China. PR contains a high quantity of isoflavones and their
glycosides, which are regarded as phytoestrogen. Few investigations
of PR are related to its osteoprotective effects. The present study is
designed to administer PR water extract to ovariectomized (OVX)
female rats, for the investigation of its possibly protective actions on
bone and to delineate the potential mechanisms involved. Our results
demonstrated that long-term treatment of PR could not significantly
improve bone properties, whereas it greatly ameliorated the condition
of secondary hyperparathyroidism induced by ovariectomy in those
animals. PR might be useful as alternative regimen for protecting
against postmenopausal bone loss.
Abstract: The great majority of the electric installations belong
to the first and second category. In order to ensure a high level of
reliability of their electric system feeder, two power supply sources
are envisaged, one principal, the other of reserve, generally a cold
reserve (electric diesel group).
The principal source being under operation, its control can be ideal
and sure, however for the reserve source being in stop, a preventive
maintenance-s which proceeds on time intervals (periodicity) and
for well defined lengths of time are envisaged, so that this source will
always available in case of the principal source failure.
The choice of the periodicity of preventive maintenance of the
source of reserve influences directly the reliability of the electric
feeder system. On the basis of the semi-markovians processes, the
influence of the periodicity of the preventive maintenance of the
source of reserve is studied and is given the optimal periodicity.
Abstract: This is a genetic comparison study of Arabian Oryx
(Oryx leucoryx) population at two different locations (A &B) based
on nuclear microsatellite DNA markers. Arabian Oryx is listed as
vulnerable and endanger by the World Conservation Union (IUCN).
Thirty microsatellite markers from bovine family were applied to
investigate the genetic diversity of the Arabian Oryx and to set up a
molecular inventory. Among 30 microsatellite markers used, 13
markers were moderately polymorphic. Arabian Oryx at location A
has shown better gene diversity over location B. However, mean
number of alleles were less than location B. Data of within
population inbreeding coefficient indicates inbreeding at both
locations (A&B). Based on the analysis of polymorphic microsatellite
markers, the study revealed that Arabian Oryx need a genetically
designed breeding program.
Abstract: In this work, we present for the first time in our
perception an efficient digital watermarking scheme for mpeg audio
layer 3 files that operates directly in the compressed data domain,
while manipulating the time and subband/channel domain. In
addition, it does not need the original signal to detect the watermark.
Our scheme was implemented taking special care for the efficient
usage of the two limited resources of computer systems: time and
space. It offers to the industrial user the capability of watermark
embedding and detection in time immediately comparable to the real
music time of the original audio file that depends on the mpeg
compression, while the end user/audience does not face any artifacts
or delays hearing the watermarked audio file. Furthermore, it
overcomes the disadvantage of algorithms operating in the PCMData
domain to be vulnerable to compression/recompression attacks,
as it places the watermark in the scale factors domain and not in the
digitized sound audio data. The strength of our scheme, that allows it
to be used with success in both authentication and copyright
protection, relies on the fact that it gives to the users the enhanced
capability their ownership of the audio file not to be accomplished
simply by detecting the bit pattern that comprises the watermark
itself, but by showing that the legal owner knows a hard to compute
property of the watermark.
Abstract: Recent medical studies have investigated the importance of enteral feeding and the use of feeding pumps for recovering patients unable to feed themselves or gain nourishment and nutrients by natural means. The most of enteral feeding system uses a peristaltic tube pump. A peristaltic pump is a form of positive displacement pump in which a flexible tube is progressively squeezed externally to allow the resulting enclosed pillow of fluid to progress along it. The squeezing of the tube requires a precise and robust controller of the geared motor to overcome parametric uncertainty of the pumping system which generates due to a wide variation of friction and slip between tube and roller. So, this paper proposes fuzzy adaptive controller for the robust control of the peristaltic tube pump. This new adaptive controller uses a fuzzy multi-layered architecture which has several independent fuzzy controllers in parallel, each with different robust stability area. Out of several independent fuzzy controllers, the most suited one is selected by a system identifier which observes variations in the controlled system parameter. This paper proposes a design procedure which can be carried out mathematically and systematically from the model of a controlled system. Finally, the good control performance, accurate dose rate and robust system stability, of the developed feeding pump is confirmed through experimental and clinic testing.