Abstract: A CFD software was employed to analyze the
characteristics of the flat round porous aerostatic bearings. The effects
of gap between the bearing and the guide way and the porosity of the
porous material on the load capacity of the bearing were studied. The
adequacy of the simulation model and the approach was verified. From
the parametric study, it is found that the depth of the flow path does not
influence the load capacity of the bearing; the load capacity of the
bearing will decrease if the thickness of the porous material increases
or the porous material protrudes above the bearing housing; the
variation of the chamfer at the edge of the bearing does not affect the
bearing load capacity. For a bearing with an air gap of 5μm and a
porosity of 0.1, the average load capacity and the pressure distribution
of the bearing are nearly unchanged no matter the bearing moves at a
constant or a varying speed.
Abstract: These paper, we approximate the average run length
(ARL) for CUSUM chart when observation are an exponential first
order moving average sequence (EMA1). We used Gauss-Legendre
numerical scheme for integral equations (IE) method for approximate
ARL0 and ARL1, where ARL in control and out of control,
respectively. We compared the results from IE method and exact
solution such that the two methods perform good agreement.
Abstract: Two algorithms are proposed to reduce the storage requirements for mammogram images. The input image goes through a shrinking process that converts the 16-bit images to 8-bits by using pixel-depth conversion algorithm followed by enhancement process. The performance of the algorithms is evaluated objectively and subjectively. A 50% reduction in size is obtained with no loss of significant data at the breast region.
Abstract: In this paper, the Tabu search algorithm is used to
solve a transportation problem which consists of determining the
shortest routes with the appropriate vehicle capacity to facilitate the
travel of the students attending the University of Mauritius. The aim
of this work is to minimize the total cost of the distance travelled by
the vehicles in serving all the customers. An initial solution is
obtained by the TOUR algorithm which basically constructs a giant
tour containing all the customers and partitions it in an optimal way
so as to produce a set of feasible routes. The Tabu search algorithm
then makes use of a search procedure, a swapping procedure and the
intensification and diversification mechanism to find the best set of
feasible routes.
Abstract: Inter-symbol interference if not taken care off may cause severe error at the receiver and the detection of signal becomes difficult. An adaptive equalizer employing Recursive Least Squares algorithm can be a good compensation for the ISI problem. In this paper performance of communication link in presence of Least Mean Square and Recursive Least Squares equalizer algorithm is analyzed. A Model of communication system having Quadrature amplitude modulation and Rician fading channel is implemented using MATLAB communication block set. Bit error rate and number of errors is evaluated for RLS and LMS equalizer algorithm, due to change in Signal to Noise Ratio (SNR) and fading component gain in Rician fading Channel.
Abstract: In this study, we report the synthesis and
characterization of nanohydroxyapatite (nHAp) in gelatin-starch
matrix via biomimetic method. Characterization of the samples was
performed using X-ray diffraction (XRD) and Fourier Transform
infrared spectroscopy (FT-IR). The Size and morphology of the
nHAp samples were determined using scanning and transmission
electron microscopy (SEM and TEM). The results reveal that the
shape and morphology of nHAp is influenced by presence of
biopolymers as template. Carbonyl and amino groups from gelatin
and hydroxyl from starch play crucial roles in HAp formation on the
surface of gelatin-starch.
Abstract: There are few studies on eggshell of leatherback turtle
which is endangered species in Thailand. This study was focusing on
the ultrastructure and elemental composition of leatherback turtle
eggshells collected from Andaman Sea Shore, Thailand during the
nesting season using scanning electron microscope (SEM). Three
eggshell layers of leatherback turtle; the outer cuticle layer or
calcareous layer, the middle layer or middle multistrata layer and the
inner fibrous layer were recognized. The outer calcareous layer was
thick and porosity which consisted of loose nodular units of various
crystal shapes and sizes. The loose attachment between these units
resulted in numerous spaces and openings. The middle layer was
compact thick with several multistrata and contained numerous
openings connecting to both outer cuticle layer and inner fibrous
layer. The inner fibrous layer was compact and thin, and composed of
numerous reticular fibers. Energy dispersive X-ray microanalysis
detector revealed energy spectrum of X-rays character emitted from
all elements on each layer. The percentages of all elements were
found in the following order: carbon (C) > oxygen (O) > calcium
(Ca) > sulfur (S) > potassium (K) > aluminum (Al) > iodine (I) >
silicon (Si) > chlorine (Cl) > sodium (Na) > fluorine (F) >
phosphorus (P) > magnesium (Mg). Each layer consisted of high
percentage of CaCO3 (approximately 98%) implying that it was
essential for turtle embryonic development. A significant difference
was found in the percentages of Ca and Mo in the 3layers. Moreover,
transition metal, metal and toxic non-metal contaminations were
found in leatherback turtle eggshell samples. These were palladium
(Pd), molybdenum (Mo), copper (Cu), aluminum (Al), lead (Pb), and
bromine (Br). The contamination elements were seen in the outer
layers except for Mo. All elements were readily observed and
mapped using Smiling program. X-ray images which mapped the
location of all elements were showed. Calcium containing in the
eggshell appeared in high contents and was widely distributing in
clusters of the outer cuticle layer to form CaCO3 structure. Moreover,
the accumulation of Na and Cl was observed to form NaCl which was
widely distributing in 3 eggshell layers. The results from this study
would be valuable on assessing the emergent success in this
endangered species.
Abstract: The effect of different tempering temperatures and heat treatment times on the corrosion resistance of austenitic stainless steels in oxalic acid was studied in this work using conventional weight loss and electrochemical measurements. Typical 304 and 316 stainless steel samples were tempered at 150oC, 250oC and 350oC after being austenized at 1050oC for 10 minutes. These samples were then immersed in 1.0M oxalic acid and their weight losses were measured at every five days for 30 days. The results show that corrosion of both types of ASS samples increased with an increase in tempering temperature and time and this was due to the precipitation of chromium carbides at the grain boundaries of these metals. Electrochemical results also confirm that the 304 ASS is more susceptible to corrosion than 316 ASS in this medium. This is attributed to the molybdenum in the composition of the latter. The metallographic images of these samples showed non–uniform distribution of precipitated chromium carbides at the grain boundaries of these metals and unevenly distributed carbides and retained austenite phases which cause galvanic effects in the medium.
Abstract: The incessant discomfort for Voluntary Counselling and Testing (VCT) exhibited by students in some tertiary institutions in Kano State, Nigeria is capable of causing Psychological Resistance as well as jeopardizing the purpose of HIV intervention. This study investigated the Prevalence of Psychological Resistance to VCT of HIV/AIDS among students of tertiary institutions in the state. Two null hypotheses were postulated and tested. Cross- Sectional Survey Design was employed in which 1512 sample was selected from a student population of 104,841 following Stratified Random Sampling technique. A self-developed 20-item scale whose reliability coefficient is 0.83 was used for data collection. Data analyzed via Chi-square and t-test reveals a prevalence of 38% with males (Mean=0.34; SD=0.475) constituting 60% and females (Mean=0.45; SD=0.498) 40%. Also, the calculated chi-square and ttest were not significant at 0.05 as such the null hypotheses were upheld. Recommendation offered suggests the use of reinforcement and social support for students who patronize HIV/AIDS counselling.
Abstract: The most widely used semiconductor memory types
are the Dynamic Random Access Memory (DRAM) and Static
Random Access memory (SRAM). Competition among memory
manufacturers drives the need to decrease power consumption and
reduce the probability of read failure. A technology that is relatively
new and has not been explored is the FinFET technology. In this
paper, a single cell Schmitt Trigger Based Static RAM using FinFET
technology is proposed and analyzed. The accuracy of the result is
validated by means of HSPICE simulations with 32nm FinFET
technology and the results are then compared with 6T SRAM using
the same technology.
Abstract: In this paper, we propose a novel method for subspace estimation used high resolution method without eigendecomposition where the sample Cross-Spectral Matrix (CSM) is replaced by upper triangular matrix obtained from LU factorization. This novel method decreases the computational complexity. The method relies on a recently published result on Rank-Revealing LU (RRLU) factorization. Simulation results demonstrates that the new algorithm outperform the Householder rank-revealing QR (RRQR) factorization method and the MUSIC in the low Signal to Noise Ratio (SNR) scenarios.
Abstract: In recent years asymmetric cross section aluminum
alloy stock has been finding increasing use in various industrial manufacturing areas such as general structures and automotive
components. In these areas, components are generally required to have
complex curved configuration and, as such, a bending process is required during manufacture. Undesirable deformation in bending
processes such as flattening or wrinkling can easily occur when thin-walled sections are bent. Hence, a thorough understanding of the
bending behavior of such sections is needed to prevent these undesirable deformations. In this study, the bending behavior of
asymmetric channel section was examined using finite element analysis (FEA). Typical methods of preventing undesirable
deformation, such as asymmetric laminated elastic mandrels were included in FEA model of draw bending. Additionally, axial tension
was applied to prevent wrinkling. By utilizing the FE simulations effect of restriction dies and axial tension on undesirable deformation during the process was clarified.
Abstract: A number of studies highlighted problems related to
ERP systems, yet, most of these studies focus on the problems during
the project and implementation stages but not during the postimplementation
use process. Problems encountered in the process of
using ERP would hinder the effective exploitation and the extended
and continued use of ERP systems and their value to organisations.
This paper investigates the different types of problems users
(operational, supervisory and managerial) faced in using ERP and
how 'feral system' is used as the coping mechanism. The paper
adopts a qualitative method and uses data collected from two cases
and 26 interviews, to inductively develop a casual network model of
ERP usage problem and its coping mechanism. This model classified
post ERP usage problems as data quality, system quality, interface
and infrastructure. The model is also categorised the different coping
mechanism through use of 'feral system' inclusive of feral
information system, feral data and feral use of technology.
Abstract: This research examines possible effects of climatic
change focusing on global warming and its impacts on world
agricultural product markets, by using a world food model developed
to consider climate changes. GDP and population for each scenario
were constructed by IPCC and climate data for each scenario was
reported by the Hadley Center and are used in this research to consider
results in different contexts. Production and consumption of primary
agriculture crops of the world for each socio-economic scenario are
obtained and investigated by using the modified world food model.
Simulation results show that crop production in some countries or
regions will have different trends depending on the context. These
alternative contexts depend on the rate of GDP growth, population,
temperature, and rainfall. Results suggest that the development of
environment friendly technologies lead to more consumption of food
in many developing countries. Relationships among environmental
policy, clean energy development, and poverty elimination warrant
further investigation.
Abstract: Polylactic acid-g-polyvinyl acetate (PLLA-g-PVAc)
was used as a compatibilizer for 50/50 starch/PLLA blend. PLLA-g-
PVAc with different mol% of PVAc contents were prepared by
grafting PVAc onto PLLA backbone via free radical polymerization
in solution process. Various conditions such as type and the amount
of initiator, monomer concentration, polymerization time and
temperature were studied. Results showed that the highest mol% of
PVAc grafting (16 mol%) was achieved by conducting graft
copolymerization in toluene at 110°C for 10 h using DCP as an
initiator. Chemical structure of the PVAc grafted PLLA was
confirmed by 1H NMR. Blending of modified starch and PLLA in the
presence compatibilizer with different amounts and mol% PVAc was
acquired using internal mixer at 160°C for 15 min. Effects of PVAc
content and the amount of compatibilizer on mechanical properties of
polymer blend were studied. Results revealed that tensile strength and
tensile modulus of polymer blend with higher PVAc grafting content
compatibilizer showed better properties than that of lower PVAc
grafting content compatibilizer. The amount of compatibilizer was
found optimized in the range of 0.5-1.0 Wt% depending on the mol%
PVAc.
Abstract: In this paper, a new hybrid of genetic algorithm (GA)
and simulated annealing (SA), referred to as GSA, is presented. In
this algorithm, SA is incorporated into GA to escape from local
optima. The concept of hierarchical parallel GA is employed to
parallelize GSA for the optimization of multimodal functions. In
addition, multi-niche crowding is used to maintain the diversity in
the population of the parallel GSA (PGSA). The performance of the
proposed algorithms is evaluated against a standard set of multimodal
benchmark functions. The multi-niche crowding PGSA and normal
PGSA show some remarkable improvement in comparison with the
conventional parallel genetic algorithm and the breeder genetic
algorithm (BGA).
Abstract: To date, theoretical studies concerning the Carbon
Fiber Reinforced Polymer (CFRP) strengthening of RC beams with
openings have been rather limited. In addition, various numerical
analyses presented so far have effectively simulated the behaviour of
solid beam strengthened by FRP material. In this paper, a two
dimensional nonlinear finite element analysis is presented to validate
against the laboratory test results of six RC beams. All beams had the
same rectangular cross-section geometry and were loaded under four
point bending. The crack pattern results of the finite element model
show good agreement with the crack pattern of the experimental
beams. The load midspan deflection curves of the finite element
models exhibited a stiffer result compared to the experimental beams.
The possible reason may be due to the perfect bond assumption used
between the concrete and steel reinforcement.
Abstract: In this paper we have proposed a novel dynamic least cost multicast routing protocol using hybrid genetic algorithm for IP networks. Our protocol finds the multicast tree with minimum cost subject to delay, degree, and bandwidth constraints. The proposed protocol has the following features: i. Heuristic local search function has been devised and embedded with normal genetic operation to increase the speed and to get the optimized tree, ii. It is efficient to handle the dynamic situation arises due to either change in the multicast group membership or node / link failure, iii. Two different crossover and mutation probabilities have been used for maintaining the diversity of solution and quick convergence. The simulation results have shown that our proposed protocol generates dynamic multicast tree with lower cost. Results have also shown that the proposed algorithm has better convergence rate, better dynamic request success rate and less execution time than other existing algorithms. Effects of degree and delay constraints have also been analyzed for the multicast tree interns of search success rate.
Abstract: A series of Ti based shape memory alloys with
composition of Ti50Ni49Cr1, Ti50Ni47Cr3 and Ti50Ni45Cr5 were
developed by vacuum arc-melting under a purified argon atmosphere.
The histometric and corrosion evaluation of Ti-Ni-Cr shape memory
alloys have been considered in this research work. The alloys were
developed by vacuum arc melting and implanted subcutaneously in
rabbits for 4, 8 and 12 weeks. Metallic implants were embedded in
order to determine the outcome of implantation on histometric and
corrosion evaluation of Ti-Ni-Cr metallic strips. Encapsulating
membrane formation around the alloys was minimal in the case of all
materials. After histomorphometric analyses it was possible to
demonstrate that there were no statistically significant differences
between the materials. Corrosion rate was also determined in this
study which is within acceptable range. The results showed the Ti-
Ni-Cr alloy was neither cytotoxic, nor have any systemic reaction on
living system in any of the test performed. Implantation shows good
compatibility and a potential of being used directly in vivo system.
Abstract: Effective cooling of electronic equipment has emerged
as a challenging and constraining problem of the new century. In the
present work the feasibility and effectiveness of jet impingement
cooling on electronics were investigated numerically and
experimentally. Studies have been conducted to see the effect of the
geometrical parameters such as jet diameter (D), jet to target
spacing (Z) and ratio of jet spacing to jet diameter (Z/D) on the heat
transfer characteristics. The values of Reynolds numbers considered
are in the range 7000 to 42000. The results obtained from the
numerical studies are validated by conducting experiments. From the
studies it is found that the optimum value of Z/D ratio is 5. For a
given Reynolds number, the Nusselt number increases by about 28%
if the diameter of the nozzle is increased from 1mm to 2mm.
Correlations are proposed for Nusselt number in terms of Reynolds
number and these are valid for air as the cooling medium.