Abstract: This paper presents the impact study of apparent
reactance injected by series Flexible AC Transmission System
(FACTS) i.e. Thyristor Controlled Series Reactor (TCSR) on the
measured impedance of a 400 kV single electrical transmission line
in the presence of phase to earth fault with fault resistance. The study
deals with an electrical transmission line of Eastern Algerian
transmission networks at Group Sonelgaz (Algerian Company of
Electrical and Gas) compensated by TCSR connected at midpoint of
the line. This compensator used to inject active and reactive powers
is controlled by three TCSR-s. The simulations results investigate the
impacts of the TCSR on the parameters of short circuit calculation
and parameters of measured impedance by distance relay in the
presence of earth fault for three cases study.
Abstract: ZnO+Ga2O3 functionally graded thin films (FGTFs)
were examined for their potential use as Solar cell and organic light
emitting diodes (OLEDs). FGTF transparent conducting oxides (TCO)
were fabricated by combinatorial RF magnetron sputtering. The
composition gradient was controlled up to 10% by changing the
plasma power of the two sputter guns. A Ga2O3+ZnO graded region
was placed on the top layer of ZnO. The FGTFs showed up to 80%
transmittance. Their surface resistances were reduced to < 10% by
increasing the Ga2O3: pure ZnO ratio in the TCO. The FGTFs- work
functions could be controlled within a range of 0.18 eV. The
controlled work function is a very promising technology because it
reduces the contact resistance between the anode and Hall transport
layers of OLED and solar cell devices.
Abstract: Multidrug resistant organisms have been taunting the
medical world for the last few decades. Even with new antibiotics
developed, resistant strains have emerged soon after. With the
advancement of nanotechnology, we investigated colloidal silver
nanoparticles for its antimicrobial activity against Pseudomonas
aeruginosa. This organism is a multidrug resistant which contributes
to the high morbidity and mortality in immunocompromised patients.
Five multidrug resistant strains were used in this study. The
antimicrobial effect was studied using the disc diffusion and broth
dilution techniques. An inhibition zone of 11 mm was observed with
10 μg dose of the nanoparticles. The nanoparticles exhibited MIC of
50 μg/ml when added at the lag phase and the subinhibitory
concentration was measured as 100 μg/ml. The MIC50 value showed
to be 15 μg/ml. This study suggests that silver nanoparticles can be
further developed as an antimicrobial agent, hence decreasing the
burden of the multidrug resistance phenomena.
Abstract: The field of biomedical materials plays an imperative
requisite and a critical role in manufacturing a variety of biological
artificial replacements in a modern world. Recently, titanium (Ti)
materials are being used as biomaterials because of their superior
corrosion resistance and tremendous specific strength, free- allergic
problems and the greatest biocompatibility compared to other
competing biomaterials such as stainless steel, Co-Cr alloys,
ceramics, polymers, and composite materials. However, regardless of
these excellent performance properties, Implantable Ti materials have
poor shear strength and wear resistance which limited their
applications as biomaterials. Even though the wear properties of Ti
alloys has revealed some improvements, the crucial effectiveness of
biomedical Ti alloys as wear components requires a comprehensive
deep understanding of the wear reasons, mechanisms, and techniques
that can be used to improve wear behavior. This review examines
current information on the effect of thermal and thermomechanical
processing of implantable Ti materials on the long-term prosthetic
requirement which related with wear behavior. This paper focuses
mainly on the evolution, evaluation and development of effective
microstructural features that can improve wear properties of bio
grade Ti materials using thermal and thermomechanical treatments.
Abstract: Wood as a natural renewable material is vulnerable to
degradation by microorganisms and susceptible to change in
dimension by water. In order to effectively improve the durability of
wood, an active reagent, maleic anhydride (Man) was selected for
wood modification. Man was first dissolved into a solvent, and then
penetrated into wood porous structure under a vacuum/pressure
condition. After a final catalyst-thermal treatment, wood modification
was finished. The test results indicate that acetone is a good solvent for
transporting Man into wood matrix. SEM observation proved that
wood samples treated by Man kept a good cellular structure, indicating
a well penetration of Man into wood cell walls. FTIR analysis
suggested that Man reacted with hydroxyl groups on wood cell walls
by its ring-ether group, resulting in reduction of amount of hydroxyl
groups and resultant good dimensional stability as well as fine decay
resistance. Consequently, Man modifying wood to improve its
durability is an effective method.
Abstract: This paper presents the design of a ring-shaped tri-axial fore sensor that can be incorporated into the tip of a guidewire for use in minimally invasive surgery (MIS). The designed sensor comprises a ring-shaped structure located at the center of four cantilever beams. The ringdesign allows surgical tools to be easily passed through which largely simplified the integration process. Silicon nanowires (SiNWs) are used aspiezoresistive sensing elementsembeddedon the four cantilevers of the sensor to detect the resistance change caused by the applied load.An integration scheme with new designed guidewire tip structure having two coils at the distal end is presented. Finite element modeling has been employed in the sensor design to find the maximum stress location in order to put the SiNWs at the high stress regions to obtain maximum output. A maximum applicable force of 5 mN is found from modeling. The interaction mechanism between the designed sensor and a steel wire has been modeled by FEM. A linear relationship between the applied load on the steel wire and the induced stress on the SiNWs were observed.
Abstract: Steel corrosion in concrete is considered as a main
engineering problems for many countries and lots of expenses has been paid for their repair and maintenance annually. This problem
may occur in all engineering structures whether in coastal and offshore or other areas. Hence, concrete structures should be able to
withstand corrosion factors existing in water or soil. Reinforcing
steel corrosion enhancement can be measured by use of concrete
electrical resistance; and maintaining high electric resistivity in concrete is necessary for steel corrosion prevention. Lots of studies
devoted to different aspects of the subjects worldwide. In this paper, an evaluation of the effects of W/C ratio, cementitious materials, and
percent increase in silica fume were investigated on electric resistivity of high strength concrete. To do that, sixteen mix design
with one aggregate grading was planned. Five of them had varying amount of W/C ratio and other eleven mixes was prepared with
constant W/C ratio but different amount of cementitious materials.
Silica fume and super plasticizer were used with different proportions
in all specimens. Specimens were tested after moist curing for 28 days. A total of 80 cube specimens (50 mm) were tested for concrete
electrical resistance. Results show that concrete electric resistivity can be increased with increasing amount of cementitious materials
and silica fume.
Abstract: This paper deals with the comparison between two proposed control strategies for a DC-DC boost converter. The first control is a classical Sliding Mode Control (SMC) and the second one is a distance based Fuzzy Sliding Mode Control (FSMC). The SMC is an analytical control approach based on the boost mathematical model. However, the FSMC is a non-conventional control approach which does not need the controlled system mathematical model. It needs only the measures of the output voltage to perform the control signal. The obtained simulation results show that the two proposed control methods are robust for the case of load resistance and the input voltage variations. However, the proposed FSMC gives a better step voltage response than the one obtained by the SMC.
Abstract: Fatigue cracking continues to be the main challenges in
improving the performance of bituminous mixture pavements. The
purpose of this paper is to look at some aspects of the effects of fine
aggregate properties on the fatigue behaviour of hot mixture asphalt.
Two types of sand (quarry and mining sand) with two conventional
bitumen (PEN 50/60 & PEN 80/100) and four polymers modified
bitumen PMB (PM1_82, PM1_76, PM2_82 and PM2_76) were used.
Physical, chemical and mechanical tests were performed on the sands
to determine their effect when incorporated with a bituminous
mixture. According to the beam fatigue results, quarry sand that has
more angularity, rougher, higher shear strength and a higher
percentage of Aluminium oxide presented higher resistance to
fatigue. Also a PMB mixture gives better fatigue results than
conventional mixtures, this is due to the PMB having better viscosity
property than that of the conventional bitumen.
Abstract: This paper argues that networks, such as the ECN and the American network, are affected by certain small events which are inherent to path dependence and preclude the full evolution towards efficiency. It is advocated that the American network is superior to the ECN in many respects due to its greater flexibility and longer history. This stems in particular from the creation of the American network, which was based on a small number of cases. Such a structure encourages further changes and modifications which are not necessarily radical. The ECN, by contrast, was established by legislative action, which explains its rigid structure and resistance to change. This paper is an attempt to transpose the superiority of the American network on to the ECN. It looks at concepts such as judicial cooperation, harmonisation of procedure, peer review and regulatory impact assessments (RIAs), and dispute resolution procedures.
Abstract: PDMS (Polydimethylsiloxane) polymer is a suitable material for biological and MEMS (Microelectromechanical systems) designers, because of its biocompatibility, transparency and high resistance under plasma treatment. PDMS round channel is always been of great interest due to its ability to confine the liquid with membrane type micro valves. In this paper we are presenting a very simple way to form round shapemicrofluidic channel, which is based on reflow of positive photoresist AZ® 40 XT. With this method, it is possible to obtain channel of different height simply by varying the spin coating parameters of photoresist.
Abstract: At the present, auto part industries have become higher challenge in strategy market. As this consequence, manufacturers need to have better response to customers in terms of quality, cost, and delivery time. Moreover, they need to have a good management in factory to comply with international standard maximum capacity and lower cost. This would lead companies to have to order standard part from aboard and become the major cost of inventory. The development of auto part research by recycling materials experiment is to compare the auto parts from recycle materials to international auto parts (CKD). Factors studied in this research were the recycle material ratios of PU-foam, felt, and fabric. Results of recycling materials were considered in terms of qualities and properties on the parameters such as weight, sound absorption, water absorption, tensile strength, elongation, and heat resistance with the CKD. The results were showed that recycling materials would be used to replace for the CKD.
Abstract: Modeling of the dynamic behavior and motion are
renewed interest in the improved tractive performance of an
intelligent air-cushion tracked vehicle (IACTV). This paper presents
a new dynamical model for the forces on the developed small scale
intelligent air-cushion tracked vehicle moving over swamp peat. The
air cushion system partially supports the 25 % of vehicle total weight
in order to make the vehicle ground contact pressure 7 kN/m2. As the
air-cushion support system can adjust automatically on the terrain, so
the vehicle can move over the terrain without any risks. The springdamper
system is used with the vehicle body to control the aircushion
support system on any undulating terrain by making the
system sinusoidal form. Experiments have been carried out to
investigate the relationships among tractive efficiency, slippage,
traction coefficient, load distribution ratio, tractive effort, motion
resistance and power consumption in given terrain conditions.
Experiment and simulation results show that air-cushion system
improves the vehicle performance by keeping traction coefficient of
71% and tractive efficiency of 62% and the developed model can
meet the demand of transport efficiency with the optimal power
consumption.
Abstract: In turning hardened steel, polycrystalline cubic boron
nitride (cBN) compacts are widely used, due to their higher hardness
and higher thermal conductivity. However, in milling hardened steel,
fracture of cBN cutting tools readily occurs because they have poor
fracture toughness. Therefore, coated cemented carbide tools, which
have good fracture toughness and wear resistance, are generally
widely used. In this study, hardened steel (ASTM D2, JIS SKD11,
60HRC) was milled with three physical vapor deposition
(PVD)-coated cemented carbide end mill cutters in order to determine
effective tool materials for cutting hardened steel at high cutting
speeds. The coating films used were (Ti,W)N/(Ti,W,Si)N and
(Ti,W)N/(Ti,W,Si,Al)N coating films. (Ti,W,Si,Al)N is a new type of
coating film. The inner layer of the (Ti,W)N/(Ti,W,Si)N and
(Ti,W)N/(Ti,W,Si,Al)N coating system is (Ti,W)N coating film, and
the outer layer is (Ti,W,Si)N and (Ti,W,Si,Al)N coating films,
respectively. Furthermore, commercial (Ti,Al)N-based coating film
was also used. The following results were obtained: (1) In milling
hardened steel at a cutting speed of 3.33 m/s, the tool wear width of the
(Ti,W)N/(Ti,W,Si,Al)N-coated tool was smaller than that of the
(Ti,W)N/(Ti,W,Si)N-coated tool. And, compared with the commercial
(Ti,Al)N, the tool wear width of the (Ti,W)N/(Ti,W,Si,Al)N-coated
tool was smaller than that of the (Ti,Al)N-coated tool. (2) The tool
wear of the (Ti,W)N/(Ti,W,Si,Al)N-coated tool increased with an
increase in cutting speed. (3) The (Ti,W)N/(Ti,W,Si,Al)N-coated
cemented carbide was an effective tool material for high-speed cutting
below a cutting speed of 3.33 m/s.
Abstract: Differentiated impact of team sports (basketball, indoor soccer, handball) on general haemodynamics and aerobic potential of students who specialize in technical subjects is detected only on the fourth year of studies in the institute of higher education. Those who play basketball and indoor soccer have shown increase of stroke and minute volume of blood indices, pumping and contractile function of the heart, oxygenation of blood and oxygen delivery to tissues, aerobic energy supply and balance of sympathetic and parasympathetic activity of the nervous regulation mechanism of the circulatory system. Those who play handball have shown these indices statistically decreased. On the whole playing basketball and indoor soccer optimizes the strategy for adaptation of students to the studying process, but playing handball does the opposite thing. The leading factor for adaptation of students is: those who play basketball have increase of minute blood volume which stipulates velocity of the system blood circulation and well-timed oxygen delivery to tissues; those who play indoor soccer have increase of power and velocity of contractile function of the heart; those who play handball have increase of resistance of thorax to the system blood flow which minimizes contractile function of the heart, blood oxygen saturation and delivery of oxygen to tissues.
Abstract: This paper describes simple implementation of
homotopy (also called continuation) algorithm for determining the proper resistance of the resistor to dissipate energy at a specified rate of an electric circuit. Homotopy algorithm can be considered as a developing of the classical methods in numerical computing such as Newton-Raphson and fixed
point methods. In homoptopy methods, an embedding
parameter is used to control the convergence. The method purposed in this work utilizes a special homotopy called Newton homotopy. Numerical example solved in MATLAB is given to show the effectiveness of the purposed method
Abstract: An alarming emergence of multidrug-resistant strains
of the tuberculosis pathogen Mycobacterium tuberculosis and
continuing high worldwide incidence of tuberculosis has invigorated
the search for novel drug targets. The enzyme glutamate racemase
(MurI) in bacteria catalyzes the stereoconversion of L-glutamate to
D-glutamate which is a component of the peptidoglycan cell wall of
the bacterium. The inhibitors targeted against MurI from several
bacterial species have been patented and are advocated as promising
antibacterial agents. However there are none available against MurI
from Mycobacterium tuberculosis, due to the lack of its threedimensional
structure. This work accomplished two major objectives.
First, the tertiary structure of MtMurI was deduced computationally
through homology modeling using the templates from bacterial
homologues. It is speculated that like in other Gram-positive bacteria,
MtMurI exists as a dimer and many of the protein interactions at the
dimer interface are also conserved. Second, potent candidate
inhibitors against MtMurI were identified through docking against
already known inhibitors in other organisms.
Abstract: In this paper is study the possibility of successfully
implementing of hollow roller concept in order to minimize inertial
mass of the large bearings, with major results in diminution of the
material consumption, increasing of power efficiency (in wind power
station area), increasing of the durability and life duration of the large
bearings systems, noise reduction in working, resistance to
vibrations, an important diminution of losses by abrasion and
reduction of the working temperature. In this purpose was developed
an original solution through which are reduced mass, inertial forces
and moments of large bearings by using of hollow rollers. The
research was made by using the method of finite element analysis
applied on software type Solidworks - Nastran. Also, is study the
possibility of rapidly changing the manufacturing system of solid and
hollow cylindrical rollers.
Abstract: Application of nanoparticles as additives in membrane
synthesis for improving the resistance of membranes against fouling
has triggered recent interest in new membrane types. However, most
nanoparticle-enhanced membranes suffer from the tradeoff between
permeability and selectivity. In this study, nano-WS2 was explored as
the additive in membrane synthesis by non-solvent induced phase
separation. Blended PES-WS2 flat-sheet membranes with the
incorporation of ultra-low concentrations of nanoparticles (from 0.025
to 0.25%, WS2/PES ratio) were manufactured and investigated in
terms of permeability, fouling resistance and solute rejection.
Remarkably, a significant enhancement in the permeability was
observed as a result of the incorporation of ultra-low fractions of
nano-WS2 to the membrane structure. Optimal permeability values
were obtained for modified membranes with 0.10%
nanoparticle/polymer concentration ratios. Furthermore, fouling
resistance and solute rejection were significantly improved by the
incorporation of nanoparticles into the membrane matrix. Specifically,
fouling resistance of modified membrane can increase by around 50%.
Abstract: Fracture process in mechanically loaded steel fiber
reinforced high-strength (SFRHSC) concrete is characterized by
fibers bridging the crack providing resistance to its opening.
Structural SFRHSC fracture model was created; material fracture
process was modeled, based on single fiber pull-out laws, which were
determined experimentally (for straight fibers, fibers with end hooks
(Dramix), and corrugated fibers (Tabix)) as well as obtained
numerically ( using FEM simulations). For this purpose experimental
program was realized and pull-out force versus pull-out fiber length
was obtained (for fibers embedded into concrete at different depth
and under different angle). Model predictions were validated by
15x15x60cm prisms 4 point bending tests. Fracture surfaces analysis
was realized for broken prisms with the goal to improve elaborated
model assumptions. Optimal SFRHSC structures were recognized.