Abstract: Jamun (Syzygium cuminii L.) is one of the important indigenous minor fruit with high medicinal value. The jamun cultivation is unorganized and there is huge loss of this fruit every year. The perishable nature of the fruit makes its postharvest management further difficult. Due to the strong cell wall structure of pectin-protein bonds and hard seeds, extraction of juice becomes difficult. Enzymatic treatment has been commercially used for improvement of juice quality with high yield. The objective of the study was to optimize the best treatment method for juice extraction. Enzymes (Pectinase and Tannase) from different stains had been used and for each enzyme, best result obtained by using response surface methodology. Optimization had been done on the basis of physicochemical property, nutritional property, sensory quality and cost estimation. According to quality aspect, cost analysis and sensory evaluation, the optimizing enzymatic treatment was obtained by Pectinase from Aspergillus aculeatus strain. The optimum condition for the treatment was 44 oC with 80 minute with a concentration of 0.05% (w/w). At these conditions, 75% of yield with turbidity of 32.21NTU, clarity of 74.39%T, polyphenol content of 115.31 mg GAE/g, protein content of 102.43 mg/g have been obtained with a significant difference in overall acceptability.
Abstract: The novel 3D SnO cabbages self-assembled by
nanosheets were successfully synthesized via template-free
hydrothermal growth method under facile conditions. The XRD
results manifest that the as-prepared SnO is tetragonal phase. The
TEM and HRTEM results show that the cabbage nanosheets are
polycrystalline structure consisted of considerable single-crystalline
nanoparticles. Two typical Raman modes A1g=210 and Eg=112 cm-1
of SnO are observed by Raman spectroscopy. Moreover, galvanostatic
cycling tests has been performed using the SnO cabbages as anode
material of lithium ion battery and the electrochemical results suggest
that the synthesized SnO cabbage structures are a promising anode
material for lithium ion batteries.
Abstract: Five palm oil ether monoesters utilized as novel
biodiesels were synthesized and structurally identified in the paper.
The investigation was made on the effect of ether species on
physicochemical properties of the palm oil ether monoesters. The
results showed that density, kinematic viscosity, smoke point, and
solidifying point increase linearly with their –CH2 group number in
certain relationships. Cetane number is enhanced whereas heat value
decreases linearly with –CH2 group number. In addition, the
influencing regularities of the volumetric content of the palm oil ether
monoesters on the fuel properties were also studied when the ether
monoesters are used as diesel fuel additives.
Abstract: The γ-turns play important roles in protein folding and
molecular recognition. The prediction and analysis of γ-turn types are
important for both protein structure predictions and better
understanding the characteristics of different γ-turn types. This study
proposed a physicochemical property-based decision tree (PPDT)
method to interpretably predict γ-turn types. In addition to the good
prediction performance of PPDT, three simple and human
interpretable IF-THEN rules are extracted from the decision tree
constructed by PPDT. The identified informative physicochemical
properties and concise rules provide a simple way for discriminating
and understanding γ-turn types.
Abstract: Fatigue cracking continues to be the main challenges in
improving the performance of bituminous mixture pavements. The
purpose of this paper is to look at some aspects of the effects of fine
aggregate properties on the fatigue behaviour of hot mixture asphalt.
Two types of sand (quarry and mining sand) with two conventional
bitumen (PEN 50/60 & PEN 80/100) and four polymers modified
bitumen PMB (PM1_82, PM1_76, PM2_82 and PM2_76) were used.
Physical, chemical and mechanical tests were performed on the sands
to determine their effect when incorporated with a bituminous
mixture. According to the beam fatigue results, quarry sand that has
more angularity, rougher, higher shear strength and a higher
percentage of Aluminium oxide presented higher resistance to
fatigue. Also a PMB mixture gives better fatigue results than
conventional mixtures, this is due to the PMB having better viscosity
property than that of the conventional bitumen.