Abstract: The coal utilization in thermal power plants in Malaysia has increased significantly which produces an enormous amount of coal combustion by-product (CCBP) or coal ash and poses severe disposal problem. As each coal ash is distinct, this study presents the geochemistry of the coal ash, in particular fly ash, produced from the combustion of local coal from Kuching Sarawak, Malaysia. The geochemical composition of the ash showed a high amount of silica, alumina, iron oxides and alkalies which was found to be a convenient starting material for the hydrothermal synthesis of zeolites with the higher Na2O percentage being a positive factor for its alkaline activation; while the mineral phases are mainly quartz, mullite, calcium oxide, silica, and iron oxide hydrate. The geochemical changes upon alkali activation that can be predicted in a similar type of ash have been described in this paper. The result shows that this particular ash has a good potential for a high value industrial product like zeolites upon alkali activation.
Abstract: Contact angle measurement was utilized in order to study the subject of the wettability and surface chemistry of the nanocomposites materials. Water and glycerol droplets were used in this study. The incorporation of layered silicate into the vinyl ester matrix helped to improve the wettability and reduced the θ values of both liquids used. The addition of 2 wt.% clay loading reduced the θ values of water and glycerol by up to 21% and 6% respectively. Likewise, the incorporation of 4 wt.% clay loading reduced the water and glycerol θ values by 49% and 38% respectively. Also this study confirms the findings in the literature regarding the relationship between the intercalation nanocomposites level and the wettability. Wide Angle X-ray Diffraction, Scanning Electron Microscopy and Transmission Electron Microscopy were utilised in order to characterise the interlamellar structure of nanocomposites.
Abstract: To develop a reliable and cost effective communication platform for the telemedicine applications, novel antenna design has been presented using bacterial foraging optimization (BFO) technique. The proposed antenna geometry is achieved by etching a modified Koch curve fractal shape at the edges and a square shape slot at the center of the radiating element of a patch antenna. It has been found that the new antenna has achieved 43.79% size reduction and better resonating characteristic than the original patch. Representative results for both simulations and numerical validations are reported in order to assess the effectiveness of the developed methodology.
Abstract: Non-woven fibrous filter media from empty fruit bunches were fabricated by using chitosan as a binder. Chitosan powder was dissolved in a 1 wt% aqueous acetic acid, and 1 wt% to 4 wt% of chitosan solutions was prepared. Chitosan-filled empty fruit bunches filter media have been prepared via wet-layup method. Thermogravimetric analysis (TGA) was performed to study various thermal properties of the fibrous filter media. It was found that the fibrous filter media have undergone several decomposition stages over a range of temperatures as revealed by TGA thermo-grams, where the temperature for 10% weight loss for chitosan-filled EFB filter media and binder-less filter media was at 150oC and 300oC, respectively.
Abstract: Although many factors play a significant role in agricultural production and productivity, the importance of soil fertility cannot be underestimated. The extent to which small farmers are able to manage the fertility of their farmlands is crucial in agricultural development particularly in sub-Saharan Africa (SSA). This paper assesses the nutrient status of selected farmers’ fields in relation to how government policy addresses the allocation of and access to agricultural inputs (e.g. chemical fertilizers) in a unique social-ecological environment of the Okavango Delta in northern Botswana. It also analyses small farmers and soil scientists’ perceptions about the political economy of integrated soil fertility management (ISFM) in the area. A multi-stage sampling procedure was used to elicit quantitative and qualitative information from 228 farmers and 9 soil researchers through the use of interview schedules and questionnaires, respectively. Knowledge validation workshops and focus group discussions (FGDs) were also used to collect qualitative data from farmers. Thirty-three composite soil samples were collected from 30 farmers’ plots in three farming communities of Makalamabedi, Nokaneng and Mohembo for laboratory analysis. While meeting points exist, farmers and scientists have divergent perspectives on soil fertility management. Laboratory analysis carried out shows that most soils in the wetland and the adjoining dry-land/upland surroundings are low in essential nutrients as well as in cation exchange capacity (CEC). Although results suggest the identification and use of appropriate inorganic fertilizers, the low CEC is an indication that holistic cultural practices, which are beyond mere chemical fertilizations, are critical and more desirable for improved soil health and sustainable livelihoods in the area. Farmers’ age (t= -0.728; p≤0.10); their perceptions about the political economy (t = -0.485; p≤0.01) of ISFM; and their preference for the use of local knowledge in soil fertility management (t = -10.254; p≤0.01) had a significant relationship with how they perceived their involvement in the implementation of ISFM.
Abstract: Indirect Evaporative Cooling process has the advantage of supplying cool air at constant moisture content. However, such system can only supply air at temperatures above wet bulb temperature. This paper presents a mathematical model for a Sub-wet bulb temperature indirect evaporative cooling arrangement that can overcome this limitation and supply cool air at temperatures approaching dew point and without increasing its moisture content. In addition, the use of porous ceramics as wet media materials offers the advantage of integration into building elements. Results of the computer show the proposed design is capable of cooling air to temperatures lower than the ambient wet bulb temperature and achieving wet bulb effectiveness of about 1.17.
Abstract: Organic farming systems still depend on intensive, mechanical soil tillage. Frequent passes by machinery traffic cause substantial soil compaction that threatens soil health. Adopting practices as reduced tillage and organic matter retention on the soil surface are considered effective ways to control soil compaction. In tropical regions, however, the acceleration of soil organic matter decomposition and soil carbon turnover on the topsoil layer is influenced more rapidly by the oscillation process of drying and wetting. It is hypothesized therefore, that rapid reduction in soil organic matter hastens the potential for compaction to occur in organic farming systems. Compaction changes soil physical properties and as a consequence it has been implicated as a causal agent in the inhibition of natural disease suppression in soils. Here we describe relationships between soil management in organic vegetable systems, soil compaction, and declining soil capacity to suppress pathogenic microorganisms.
Abstract: Psychoacoustics has become a potential area of research due to the growing interest of both laypersons and medical and mental health professionals. Non invasive brain computer interface like Electroencephalography (EEG) is widely being used in this field. An attempt has been made in this paper to examine the response of EEG signals to acoustic stimuli further analyzing the brain electrical activity. The real time EEG is acquired for 6 participants using a cost effective and portable EMOTIV EEG neuro headset. EEG data analysis is further done using EMOTIV test bench, EDF browser and EEGLAB (MATLAB Tool) application software platforms. Spectral analysis of acquired neural signals (AF3 channel) using these software platforms are clearly indicative of increased brain activity in various bands. The inferences drawn from such an analysis have significant correlation with subject’s subjective reporting of the experiences. The results suggest that the methodology adopted can further be used to assist patients with sleeping and depressive disorders.
Abstract: Real time non-invasive Brain Computer Interfaces have a significant progressive role in restoring or maintaining a quality life for medically challenged people. This manuscript provides a comprehensive review of emerging research in the field of cognitive/affective computing in context of human neural responses. The perspectives of different emotion assessment modalities like face expressions, speech, text, gestures, and human physiological responses have also been discussed. Focus has been paid to explore the ability of EEG (Electroencephalogram) signals to portray thoughts, feelings, and unspoken words. An automated workflow-based protocol to design an EEG-based real time Brain Computer Interface system for analysis and classification of human emotions elicited by external audio/visual stimuli has been proposed. The front end hardware includes a cost effective and portable Emotiv EEG Neuroheadset unit, a personal computer and a set of external stimulators. Primary signal analysis and processing of real time acquired EEG shall be performed using MATLAB based advanced brain mapping toolbox EEGLab/BCILab. This shall be followed by the development of MATLAB based self-defined algorithm to capture and characterize temporal and spectral variations in EEG under emotional stimulations. The extracted hybrid feature set shall be used to classify emotional states using artificial intelligence tools like Artificial Neural Network. The final system would result in an inexpensive, portable and more intuitive Brain Computer Interface in real time scenario to control prosthetic devices by translating different brain states into operative control signals.
Abstract: This experiment aims to demonstrate the efficacy of ceramic powder derived from various sources to inactivate avian influenza virus and its possibility to use in the environment. The ceramics used in the present experiment were derived from chicken feces (CF), scallop shell (SS), polyvinyl chloride (PVC) and soybean (SB). All ceramics were mixed with low pathogenic AIV (LPAIV) H7N1, and then kept at room temperature. The recovered virus was titrated onto Madin-Darby canine kidney (MDCK) cells. All ceramics were assessed the inactivation stability in the environment by keeping under sunlight and under wet-dry condition until reached 7 week or 7 resuspension times respectively. The results indicate that all ceramics have excellent efficacy to inactivate LPAIV. This efficacy can be maintained under the simulated condition. The ceramics are expected to be the good materials for application in the biosecurity system at farms.
Abstract: A numerical study has been conducted to investigate the influence of fin pitch and relative humidity on the heat transfer performance of the fin-and-tube heat exchangers having plain fin geometry under dehumidifying conditions. The analysis is done using the ratio between the heat transfer coefficients in totally wet conditions and those in totally dry conditions using the appropriate correlations for both dry and wet conditions. For a constant relative humidity, it is found that the heat transfer coefficient increases with the increase of the air frontal velocity. By contrast, the fin efficiency decreases when the face velocity is increased. Apparently, this phenomenon is attributed to the path of condensate drainage. For the influence of relative humidity, the results showed an increase in heat transfer performance and a decrease in wet fin efficiency when relative humidity increases. This is due to the higher amount of mass transfer encountered at higher relative humidity. However, it is found that the effect of fin pitch on the heat transfer performance depends strongly on the face velocity. At lower frontal velocity the heat transfer increases with fin pitch. Conversely, an increase in fin pitch gives lower heat transfer coefficients when air velocity is increased.
Abstract: This paper presents a comparative study on dry and wet grinding through experimental investigation in the grinding of CSM glass fibre reinforced polymer laminates using a pink aluminium oxide wheel. Different sets of experiments were performed to study the effects of the independent grinding parameters such as grinding wheel speed, feed and depth of cut on dependent performance criteria such as cutting forces and surface finish. Experimental conditions were laid out using design of experiment central composite design. An effective coolant was sought in this study to minimise cutting forces and surface roughness for GFRP laminates grinding. Test results showed that the use of coolants reduces surface roughness, although not necessarily the cutting forces. These research findings provide useful economic machining solution in terms of optimized grinding conditions for grinding CSM GFRP.
Abstract: Paleoclimate was reconstructed by the clay mineral
assemblages of shale units of Pabdeh (Paleocene- Oligocene), Gurpi
(Upper Cretaceous), Kazhdumi (Albian-Cenomanian) and Gadvan
(Aptian-Neocomian) formations in the Bangestan anticline. To
compare with clay minerals assemblages in these formations,
selected samples also taken from available formations in drilled wells
in Ahvaz, Marun, Karanj, and Parsi oil fields. Collected samples
prepared using standard clay mineral methodology. They were
treated as normal, glycolated and heated oriented glass slides. Their
identification was made on X-Ray diffractographs. Illite % varies
from 8 to 36. Illite quantity increased from Pabdeh to Gurpi
Formation. This may be due to dominant dry climate. Kaolinite is in
range of 12-49%. Its variation style in different formations could be a
marker of climate changes from wet to dry which is supported by the
lithological changes. Chlorite (4-28%) can also be detected in those
samples without any kaolinite. Mixed layer minerals as the mixture
of illite-chlorite and illite-vermiculite-montmorillonite are varied
from 6 to 36%, decreased during Kazhdumi deposition from the base
to the top. This result may be according to decreasing of illite
leaching process. Vermiculite was also determined in very less
quantity and found in those units without kaolinite. Montmorillonite
varies from 8 to 43%, and its presence is due to terrestrial
depositional condition. Stratigraphical documents is also supported
this idea that clay mineral distribution is a function of the climate
changes. It seems, thus, the present results can be indicated a possible
procedure for ancient climate changes evaluation.
Abstract: The development of wireless communication technologies has changed our living style in global level. After the international success of mobile telephony standards, the location and time independent voice connection has become a default method in daily telecommunications. As for today, highly advanced multimedia messaging plays a key role in value added service handling. Along with evolving data services, the need for more complex applications can be seen, including the mobile usage of broadcast technologies. Here performance of a system design for terrestrial multimedia content is examined with emphasis on mobile reception. This review paper has accommodated the understanding of physical layer role and the flavour of terrestrial channel effects on the terrestrial multimedia transmission using OFDM keeping DVB-H as benchmark standard.
Abstract: Ever since industrial revolution began, our ecosystem
has changed. And indeed, the negatives outweigh the positives.
Industrial waste usually released into all kinds of body of water, such
as river or sea. Tempeh waste is one example of waste that carries
many hazardous and unwanted substances that will affect the
surrounding environment. Tempeh is a popular fermented food in
Asia which is rich in nutrients and active substances. Tempeh liquid
waste- in particular- can cause an air pollution, and if penetrates
through the soil, it will contaminates ground-water, making it
unavailable for the water to be consumed. Moreover, bacteria will
thrive within the polluted water, which often responsible for causing
many kinds of diseases. The treatment used for this chemical waste is
biological treatment such as constructed wetland and activated
sludge. These kinds of treatment are able to reduce both physical and
chemical parameters altogether such as temperature, TSS, pH, BOD,
COD, NH3-N, NO3-N, and PO4-P. These treatments are implemented
before the waste is released into the water. The result is a
comparation between constructed wetland and activated sludge,
along with determining which method is better suited to reduce the
physical and chemical subtances of the waste.
Abstract: Climate change causes severe effects on natural
habitats, especially wetlands. These challenges require the adaptation
of their management to probable effects of climate change. A
compilation of necessary changes in land management was collected
in a Hungarian area being both national park and Natura 2000 SAC
and SCI site in favor of increasing the resilience and reducing
vulnerability. Several factors, such as ecological aspects, nature
conservation and climatic adaptation should be combined with social
and economic factors during the process of developing climate
change adapted management on vulnerable wetlands. Planning
adaptive management should be determined by a priority order of
conservation aims and evaluation of factors at the determined
planning unit. Mowing techniques, frequency and exact date should
be observed as well as grazing species and their breed, due to
different grazing, group forming and trampling habits. Integrating
landscape history and historical land development into the planning
process is essential.
Abstract: The growing health hazardous impact of arsenic (As)
contamination in environment is the impetus of the present
investigation. Application of lactic acid bacteria (LAB) for the
removal of toxic and heavy metals from water has been reported.
This study was performed in order to isolate and characterize the Asresistant
LAB from mud and sludge samples for using as efficient As
uptaking probiotic. Isolation of As-resistant LAB colonies was
performed by spread plate technique using bromocresol purple
impregnated-MRS (BP-MRS) agar media provided with As @ 50
μg/ml. Isolated LAB were employed for probiotic characterization
process, acid and bile tolerance, lactic acid production, antibacterial
activity and antibiotic tolerance assays. After As-resistant and
removal characterizations, the LAB were identified using 16S rDNA
sequencing. A total of 103 isolates were identified as As-resistant
strains of LAB. The survival of 6 strains (As99-1, As100-2, As101-3,
As102-4, As105-7, and As112-9) was found after passing through the
sequential probiotic characterizations. Resistant pattern pronounced
hollow zones at As concentration >2000 μg/ml in As99-1, As100-2,
and As101-3 LAB strains, whereas it was found at ~1000 μg/ml in
rest 3 strains. Among 6 strains, the As uptake efficiency of As102-4
(0.006 μg/h/mg wet weight of cell) was higher (17 – 209%)
compared to remaining LAB. 16S rDNA sequencing data of 3 (As99-
1, As100-2, and As101-3) and 3 (As102-4, As105-7, and As112-9)
LAB strains clearly showed 97 to 99% (340 bp) homology to
Pediococcus dextrinicus and Pediococcus acidilactici, respectively.
Though, there was no correlation between the metal resistant and
removal efficiency of LAB examined but identified elevated As
removing LAB would probably be a potential As uptaking probiotic
agent. Since present experiment concerned with only As removal
from pure water, As removal and removal mechanism in natural
condition of intestinal milieu should be assessed in future studies.
Abstract: Pre-germinated parboiled brown rice or Khao hang (in Thai) is paddy which undergoing the processes of soaking, steaming, drying and dehusking to obtain the edible form for consumption. The objectives of this research were to study the kinetic of pre-germinated parboiled brown rice drying using fluidization technique and to study the properties of pre-germinated parboiled brown rice after drying. The dryings were performed at the different temperatures of 110, 120 and 130 oC at the bed depth of 2 cm with the air velocity of 1.98 m/s. The results found that the higher drying temperature led to the faster moisture reduction. After drying until the moisture content of pre-germinated parboiled brown rice was lower than 14%wet basis, samples were taken to determine various qualities such as percentage of head rice and L* a* b* color values. The shade drying was used as a control. The results found that the higher drying temperature resulted in the decrease of head rice percentage. For the color assessment, the trend of L* and a* values was increased with the drying temperature, while the b* value was not significantly difference (p › 0.05) by drying temperatures. However, the b value of drying by fluidized bed dryer was higher than the control.
Abstract: This study presents a systematic analysis of wetted region due to cooling of aluminum plate by water spray impingement with respect to different water flow rates, spray nozzle heights, and subcooling. Unlike jet impingement, the wetting is not commenced upon spray impingement and there is a delay in wetness of hot test surface. After initiation, the wetting (black zone) progresses gradually to cover all test plate and provides efficient cooling in nucleate boiling regime. Generally, spray cooling is found function of spray flow rate, spray-to-surface distance and water subcooling. Wetting delay is decreasing by increasing of spray flow rate until spray impact area is not become bigger that test surface. Otherwise, higher spray flow rate is not practically accelerated start of wetting. Very fast wetting due to spray cooling can be obtained by dense spray (high floe rate) discharged from adjacent nozzle to the test surface. Highly subcooling water spray also triggers earlier wetting of hot aluminum plate.
Abstract: The aim of this study was to investigate the influence
of reaction temperature and wheat straw moisture content on the
pyrolysis product yields, in the temperature range of 475-575 °C.
Samples of straw with moisture contents from 1.5 wt % to 15.0 wt %
were fed to a bench scale Pyrolysis Centrifuge Reactor (PCR). The
experimental results show that the changes in straw moisture content
have no significant effect on the distribution of pyrolysis product
yields. The maximum bio-oil yields approximately 60 (wt %, on dry
ash free feedstock basis) was observed around 525 °C - 550 °C for all
straw moisture levels. The water content in the wet straw bio-oil was
the highest. The heating value of bio-oil and solid char were
measured and the percentages of its energy distribution were
calculated. The energy distributions of bio-oil, char and gas were 56-
69 % 24-33 %, and 2-19 %, respectively.