Abstract: Periphyton development and composition were
studied in three different treatments: (i) two fishpond units of
wetland-type wastewater treatment pond systems, (ii) two fishponds
in combined intensive-extensive fish farming systems and (iii) three
traditional polyculture fishponds. Results showed that amounts of
periphyton developed in traditional polyculture fishponds (iii) were
different compared to the other treatments (i and ii), where the main
function of ponds was stated wastewater treatment. Negative
correlation was also observable between water quality parameters
and periphyton production. The lower trophity, halobity and
saprobity level of ponds indicated higher amount of periphyton. The
dry matter content of periphyton was significantly higher in the
samples, which were developed in traditional polyculture fishponds
(2.84±3.02 g m-2 day-1, whereby the ash content in dry matter 74%),
than samples taken from (i) (1.60±2.32 g m-2 day-1, 61%) and (ii)
fishponds (0.65±0.45 g m-2 day-1, 81%).
Abstract: Pyrolysis of waste tire is one of alternative technique
to produce petrochemicals, such as light olefins, mixed C4, and monoaromatics.
Noble metals supported on acid zeolite catalysts were
reported as potential catalysts to produce the high valuable products
from waste tire pyrolysis. Especially, Pd supported on HBeta gave a
high yield of olefins, mixed C4, and mono-aromatics. Due to the high
prices of noble metals, the objective of this work was to investigate
whether or not a non-noble Ni metal can be used as a substitute of a
noble metal, Pd, supported on HBeta as a catalyst for waste tire pyrolysis.
Ni metal was selected in this work because Ni has high activity
in cracking, isomerization, hydrogenation and the ring opening of
hydrocarbons Moreover, Ni is an element in the same group as Pd
noble metal, which is VIIIB group, aiming to produce high valuable
products similarly obtained from Pd. The amount of Ni was varied as
5, 10, and 20% by weight, for comparison with a fixed 1 wt% Pd,
using incipient wetness impregnation. The results showed that as a
petrochemical-producing catalyst, 10%Ni/HBeta performed better
than 1%Pd/HBeta because it did not only produce the highest yield of
olefins and cooking gases, but the yields were also higher than
1%Pd/HBeta. 5%Ni/HBeta can be used as a substitute of
1%Pd/HBeta for similar crude production because its crude contains
the similar amounts of naphtha and saturated HCs, although it gave
no concentration of light mono-aromatics (C6-C11) in the oil. Additionally,
10%Ni/HBeta that gave high olefins and cooking gases was
found to give a fairly high concentration of the light mono-aromatics
in the oil.
Abstract: Studies have shown that the SnAgCu solder family has been widely used as a replacement for conventional Sn-Pb solders. An attractive approach is by introducing alloying additives (rare earth elements (RE), Zn, Co, Fe, Ni, Sb) into the SnAgCu solder, which helps in refining the microstructure also improving the mechanical and wetting properties of the solder. The present work focuses on the effect of additions of 0.5% Ce and Fe into Sn-3.0Ag-0.5Cu solder, in attempt to reduce the intermetallic compound (IMC) growth and reflow properties of the solder on Cu and Ni (P) surface finish, as well as effects thermal aging on the formation of intermetallic compound (IMC) on different surface finish. Excessive intermetallic compound growth may effect the interface and solder joint due to the brittle nature of the intermetallic compounds. Thus, by introducing alloying elements, IMC layer thickness can be decrease, resulting in better joint and solder reliability.
Abstract: Binder drainage test is widely used to set an upper
limit to the design binder content of porous asphalt. However, the
presence of high amount of fine particles in the drained binder may
affect the accuracy of the test result. This paper presents a study to
characterize the composition and particle size distribution of fine
particles accumulated in the drained binder. Fine aggregates and filler
in the drained binder were extracted using a suitable solvent. Then,
wet and dry sieve analysis was carried out to identify the actual
composition of the extracted fine aggregates and filler. From the
results, almost half of the drained binder consisted of fine aggregates
and this significantly affects the accuracy of the design binder content
of porous asphalt mix. This simple finding highlights the importance
of taking into account the presence of fine aggregates in the
calculation of drained binder.
Abstract: Many methods exist for either measuring or estimating
evaporation from free water surfaces. Evaporation pans provide one
of the simplest, inexpensive, and most widely used methods of
estimating evaporative losses. In this study, the rate of evaporation
starting from a water surface was calculated by modeling with
application to dams in wet, arid and semi arid areas in Algeria.
We calculate the evaporation rate from the pan using the energy
budget equation, which offers the advantage of an ease of use, but
our results do not agree completely with the measurements taken by
the National Agency of areas carried out using dams located in areas
of different climates. For that, we develop a mathematical model to
simulate evaporation. This simulation uses an energy budget on the
level of a vat of measurement and a Computational Fluid Dynamics
(Fluent). Our calculation of evaporation rate is compared then by the
two methods and with the measures of areas in situ.
Abstract: Porcelain specimens were fired at 6C/min to 1250C (dwell time 0.5-3h) and cooled at 6C/min to room temperature. Additionally, three different slower firing/cooling cycles were tried. Sintering profile and effects on MOR, crystalline phase content and morphology were investigated using dilatometry, 4-point bending strength, XRD and FEG-SEM respectively. Industrial-sized specimens prepared using the promising cycle were tested basing on the ANSI standards. Increasing dwell time from 1h to 3h at peak temperature of 1250C resulted in neither a significant effect on the quartz and mullite content nor MOR. Reducing the firing/cooling rate to below 6C/min, for peak temperature of 1250C (dwell time of 1h) does not result in improvement of strength of porcelain. The industrial sized specimen exhibited flashover voltages of 20.3kV (dry) and 9.3kV (wet) respectively, transverse strength of 12.5kN and bulk density of 2.27g/cm3, which are satisfactory. There was however dye penetration during porosity test. KeywordsDwell time, Microstructure, Porcelain, Strength.
Abstract: This study evaluates the performance of horizontal
subsurface flow constructed wetland (HSSF-CW) for the removal of
chlorinated resin and fatty acids (RFAs) from pulp and paper mill
wastewater. The dimensions of the treatment system were 3.5 m x 1.5
m x 0.28 m with surface area of 5.25 m2, filled with fine sand and
gravel. The cell was planted with an ornamental plant species Canna
indica. The removal efficiency of chlorinated RFAs was in the range
of 92-96% at the hydraulic retention time (HRT) of 5.9 days. Plant
biomass and soil (sand and gravel) were analyzed for chlorinated
RFAs content. No chlorinated RFAs were detected in plant biomass
but detected in soil samples. Mass balance studies of chlorinated
RFAs in HSSF-CW were also carried out.
Abstract: Auckland has a temperate climate with comfortable
warm, dry summers and mild, wet winters. An Auckland school
normally does not need air conditioning for cooling during the
summer and only need heating during the winter. The space hating
energy is the major portion of winter school energy consumption and
the winter energy consumption is major portion of annual school
energy consumption. School building thermal design should focus
on the winter thermal performance for reducing the space heating
energy. A number of Auckland schools- design data and energy
consumption data are used for this study. This pilot study
investigates the relationships between their energy consumption data
and school building design data to improve future school design for
energy efficiency.
Abstract: The Bulgarian natural expanded mineral obtained from Bentonite AD perlite (A deposit of "The Broken Mountain" for perlite mining, near by the village of Vodenicharsko, in the municipality of Djebel), was loaded with silver (as ion form - Ag+ 2 and 5 wt% by the incipient wetness impregnation method), and as atomic silver - Ag0 using Tollen-s reagent (silver mirror reaction). Some physicochemical characterization of the samples are provided via: DC arc-AES, XRD, DR-IR and UV-VIS. The aim of this work was to obtain and test the silver-loaded catalyst for ozone decomposition. So the samples loaded with atomic silver show ca. 80% conversion of ozone 20 minutes after the reaction start. Then conversion decreases to ca. 20 % but stay stable during the prolongation of time.
Abstract: High purity hydrogen and the valuable by-product of carbon nanotubes (CNTs) can be produced by the methane catalytic decomposition. The methane conversion and the performance of CNTs were determined by the choices of catalysts and the condition of decomposition reaction. In this paper, Ni/MgO and Ni/O-D (oxidized diamond) catalysts were prepared by wetness impregnation method. The effects of reaction temperature and space velocity of methane on the methane conversion were investigated in a fixed-bed. The surface area, structure and micrography were characterized with BET, XPS, SEM, EDS technology. The results showed that the conversion of methane was above 8% within 150 min (T=500) for 33Ni/O-D catalyst and higher than 25% within 120 min (T=650) for 41Ni/MgO catalyst. The initial conversion increased with the increasing temperature of the decomposition reaction, but their catalytic activities decreased rapidly while at too higher temperature. To decrease the space velocity of methane was propitious to promote the methane conversion, but not favor of the hydrogen yields. The appearance of carbon resulted from the methane decomposition lied on the support type and the condition of catalytic reaction. It presented as fiber shape on the surface of Ni/O-D at the relatively lower temperature such as 500 and 550, but as grain shape stacked on and overlayed on the surface of the metal nickel while at 650. The carbon fiber can form on the Ni/MgO surface at 650 and the diameter of the carbon fiber increased with the decreasing space velocity.
Abstract: Water samples were collected from river Pandu at six
stations where human and animal activities were high. Composite
samples were analyzed for dissolved oxygen (DO), biochemical
oxygen demand (BOD), chemical oxygen demand (COD) , pH values
during dry and wet seasons as well as the harmattan period. The total
data points were used to establish relationships between the
parameters and data were also subjected to statistical analysis and
expressed as mean ± standard error of mean (SEM) at a level of
significance of p
Abstract: Gas turbine systems with wet compression have a
potential for future power generation, since they can offer a high
efficiency and a high specific power with a relatively low cost. In this
study influence of ambient condition on the performance of the wet
compression process is investigated with a non-equilibrium analytical
modeling based on droplet evaporation. Transient behaviors of droplet
diameter and temperature of mixed air are investigated for various
ambient temperatures. Special attention is paid for the effects of
ambient temperature, pressure ratio, and water injection ratios on the
important wet compression variables including compressor outlet
temperature and compression work. Parametric studies show that
downing of the ambient temperature leads to lower compressor outlet
temperature and consequently lower consumption of compression
work even in wet compression processes.
Abstract: Later marine propeller is the main component of ship
propulsion system. For a non-series propeller, it is difficult to
indicate the open water marine propeller performance without an
experimental study to measure the marine propeller parameters.
In the present study, the open water performance of a non-series
marine propeller has been carried out experimentally. The
geometrical aspects of a commercial non-series marine propeller
have been measured for a propeller blade area ratio of 0.3985. The
measured propeller performance parameters were the thrust and
torque coefficients for different propeller rotational speed and
different water channel flow velocity, then the open water
performance for the propeller has been plotted.
In addition, a direct comparison between the obtained
experimental results and a theoretical study of a B-series marine
propeller of the same blade area ratio has been carried out. A
correction factor has been introduced to apply the operating
conditions of the experimental results to that of the theoretical study
for the studied marine propeller.
Abstract: The aim of this study is to discuss the relationship between tourist awareness of environmental issues and their own recreational behaviors in the Taipei Guandu Wetland. A total of 392 questionnaires were gathered for data analysis using descriptive statistics, t-testing, one-way analysis of variance (ANOVA) and least significant difference (LSD) post hoc comparisons. The results showed that most of the visitors there enjoying the beautiful scenery are 21 to 30 years old with a college education. The means and standard deviations indicate that tourists express a positive degree of cognition of environmental issues and recreational behaviors. They suggest that polluting the environment is harmful to the natural ecosystem and that the natural resources of ecotourism are fragile, as well as expressing a high degree of recognition of the need to protect wetlands. Most of respondents are cognizant of the regulations proposed by the Guandu Wetland administration which asks that users exercise self-control and follow recommended guidelines when traveling the wetland. There were significant differences in the degree of cognition related to the variables of age, number of visits and reasons for visiting. We found that most respondents with relatively high levels of education would like to learn more about the wetland and are supportive of its conservation.
Abstract: Wet chemistry methods are used to prepare the
SiO2/Au nanoshells. The purpose of this research was to synthesize
gold coated SiO2 nanoshells for biomedical applications. Tunable
nanoshells were prepared by using different colloidal concentrations.
The nanoshells are characterized by FTIR, XRD, UV-Vis
spectroscopy and atomic force microscopy (AFM). The FTIR results
confirmed the functionalization of the surfaces of silica nanoparticles
with NH2 terminal groups. A tunable absorption was observed
between 470-600 nm with a maximum range of 530-560 nm. Based
on the XRD results three main peaks of Au (111), (200) and (220)
were identified. Also AFM results showed that the silica core
diameter was about 100 nm and the thickness of gold shell about 10
nm.
Abstract: This work presents the experimental results obtained
at a pilot plant which works with a slow, wet and catalytic pyrolysis
process of dry fowl manure. This kind of process mainly consists in
the cracking of the organic matrix and in the following reaction of
carbon with water, which is either already contained in the organic
feed or added, to produce carbon monoxide and hydrogen. Reactions
are conducted in a rotating reactor maintained at a temperature of
500°C; the required amount of water is about 30% of the dry organic
feed. This operation yields a gas containing about 59% (on a volume
basis) of hydrogen, 17% of carbon monoxide and other products such
as light hydrocarbons (methane, ethane, propane) and carbon
monoxide in lesser amounts. The gas coming from the reactor can be
used to produce not only electricity, through internal combustion
engines, but also heat, through direct combustion in industrial
boilers. Furthermore, as the produced gas is devoid of both solid
particles and pollutant species (such as dioxins and furans), the
process (in this case applied to fowl manure) can be considered as an
optimal way for the disposal and the contemporary energetic
valorization of organic materials, in such a way that is not damaging
to the environment.
Abstract: UK breweries generate extensive by products in the
form of spent grain, slurry and yeast. Much of the spent grain is
produced by large breweries and processed in bulk for animal feed.
Spent brewery grains contain up to 20% protein dry weight and up to
60% fiber and are useful additions to animal feed. Bulk processing is
economic and allows spent grain to be sold so providing an income
to the brewery. A proportion of spent grain, however, is produced by
small local breweries and is more variably distributed to farms or
other users using intermittent collection methods. Such use is much
less economic and may incur losses if not carefully assessed for
transport costs. This study reports an economic returns of using wet
brewery spent grain (WBSG) in animal feed using the Co-product
Optimizer Decision Evaluator model (Cattle CODE) developed by
the University of Nebraska to predict performance and economic
returns when byproducts are fed to finishing cattle. The results
indicated that distance from brewery to farm had a significantly
greater effect on the economics of use of small brewery spent grain
and that alternative uses than cattle feed may be important to
develop.
Abstract: In this paper, the feasibility study of using a hybrid
system of ground heat exchangers (GHE) and direct evaporative
cooling system in arid weather condition has been performed. The
model is applied for Yazd and Kerman, two cities with arid weather
condition in Iran. The system composed of three sections: Ground-
Coupled-Circuit (GCC), Direct Evaporative Cooler (DEC) and
Cooling Coil Unite (CCU). The GCC provides the necessary precooling
for DEC. The GCC includes four vertical GHE which are
designed in series configuration. Simulation results show that
hybridization of GCC and DEC could provide comfort condition
whereas DEC alone did not. Based on the results the cooling
effectiveness of a hybrid system is more than unity. Thus, this novel
hybrid system could decrease the air temperature below the ambient
wet-bulb temperature. This environmentally clean and energy
efficient system can be considered as an alternative to the mechanical
vapor compression systems.
Abstract: The aim of this study is to develop a cost-effective WBGT heat stress monitor which provides precise heat stress measurement. The proposed device employs SHT15 and DS18B20 as a temperature and humidity sensors, respectively, incorporating with ATmega328 microcontroller. The developed heat stress monitor was calibrated and adjusted to that of the standard temperature and humidity sensors in the laboratory. The results of this study illustrated that the mean percentage error and the standard deviation from the measurement of the globe temperature was 2.33 and 2.71 respectively, while 0.94 and 1.02 were those of the dry bulb temperature, 0.79 and 0.48 were of the wet bulb temperature, and 4.46 and 1.60 were of the relative humidity sensor. This device is relatively low-cost and the measurement error is acceptable.
Abstract: The urban centers within northeastern Brazil are
mainly influenced by the intense rainfalls, which can occur after long
periods of drought, when flood events can be observed during such
events. Thus, this paper aims to study the rainfall frequencies in such
region through the wavelet transform. An application of wavelet
analysis is done with long time series of the total monthly rainfall
amount at the capital cities of northeastern Brazil. The main
frequency components in the time series are studied by the global
wavelet spectrum and the modulation in separated periodicity bands
were done in order to extract additional information, e.g., the 8 and
16 months band was examined by an average of all scales, giving a
measure of the average annual variance versus time, where the
periods with low or high variance could be identified. The important
increases were identified in the average variance for some periods,
e.g. 1947 to 1952 at Teresina city, which can be considered as high
wet periods. Although, the precipitation in those sites showed similar
global wavelet spectra, the wavelet spectra revealed particular
features. This study can be considered an important tool for time
series analysis, which can help the studies concerning flood control,
mainly when they are applied together with rainfall-runoff
simulations.