Abstract: The aim of this investigation is to study the
performance of the new generation of the PVD coated grade and to
map the influence of cutting conditions on the tool life in milling of
ADI (Austempered Ductile Iron). The results show that chipping is
the main wear mechanism which determines the tool life in dry
condition and notch wear in wet condition for this application. This
due to the different stress mechanisms and preexisting cracks in the
coating. The wear development shows clearly that the new PVD
coating (C20) has the best ability to delay the chipping growth. It
was also found that a high content of Al in the new coating (C20)
was especially favorable compared to a TiAlN multilayer with lower
Al content (C30) or CVD coating. This is due to fine grains and low
compressive stress level in the coating which increase the coating
ability to withstand the mechanical and thermal impact. It was also
found that the use of coolant decreases the tool life with 70-80%
compare to dry milling.
Abstract: Microstructure, wetting behavior and interfacial
reactions between Sn–0.7Cu and Sn–0.3Ag–0.7Cu (SAC0307)
solders solidified on Ni coated Al substrates were compared and
investigated. Microstructure of Sn–0.7Cu alloy exhibited a eutectic
matrix composed of primary β-Sn dendrites with a fine dispersion of
Cu6Sn5 intermetallics whereas microstructure of SAC0307 alloy
exhibited coarser Cu6Sn5 and finer Ag3Sn precipitates of IMCs with
decreased tin dendrites. Contact angles ranging from 22° to 26° were
obtained for Sn–0.7Cu solder solidified on substrate surface whereas
for SAC0307 solder alloy contact angles were found to be in the
range of 20° to 22°. Sn–0.7Cu solder/substrate interfacial region
exhibited faceted (Cu, Ni)6Sn5 IMCs protruding into the solder matrix
and a small amount of (Cu, Ni)3Sn4 intermetallics at the interface.
SAC0307 solder/substrate interfacial region showed mainly (Cu,
Ni)3Sn4 intermetallics adjacent to the coating layer and (Cu,
Ni)6Sn5 IMCs in the solder matrix. The improvement in the
wettability of SAC0307 solder alloy on substrate surface is attributed
to the formation of cylindrical shape (Cu,Ni)6Sn5 and a layer of
(Cu, Ni)3Sn4 IMCs at the interface.
Abstract: Groundwater is one of the most important water resources in Fars province. Based on this study, 95 percent of the total annual water consumption in Fars is used for agriculture, whereas the percentages for domestic and industrial uses are 4 and 1 percent, respectively. Population growth, urban and industrial growth, and agricultural development in Fars have created a condition of water stress. In this province, farmers and other users are pumping groundwater faster than its natural replenishment rate, causing a continuous drop in groundwater tables and depletion of this resource. In this research variation of groundwater level , their effects and ways to help control groundwater levels in some plains of Fars were evaluated .Excessive exploitation of groundwater in Darab, Jahrom, Estahban, Arsanjan, Khir and Niriz plains of Fars caused the groundwater levels fall too fast or to unacceptable levels. The average drawdown of the water table in Arsanjan, Khir. Estahban and Niriz plain plains were 12,8, 9 and 6 meters during 16,11,11 and 13 years ago respectively. This not only reduces available water resources and well yields but also can saline water intrusion, reductions in river flow and in wetland areas , drying springs, and ground subsidence, considerable increase in pumping costs and a significant decline in crop yields as a result of the increasing salinity. Finally based on situation and condition of the aquifer some suggestions are recommended.
Abstract: A water reuse system in wetland paddy was simulated
to supply water for industrial in this paper. A two-tank model was employed to represent the return flow of the wetland paddy.Historical data were performed for parameter estimation and model verification. With parameters estimated from the data, the model was then used to simulate a reasonable return flow rate from the wetland
paddy. The simulation results show that the return flow ratio was 11.56% in the first crop season and 35.66% in the second crop
season individually; the difference may result from the heavy rainfall in the second crop season. Under the existent pond with surplus
active capacity, the water reuse ratio was 17.14%, and the water supplementary ratio was 21.56%. However, the pattern of rainfall, the
active capacity of the pond, and the rate of water treatment limit the
volume of reuse water. Increasing the irrigation water, dredging the
depth of pond before rainy season and enlarging the scale of module are help to develop water reuse system to support for the industrial
water use around wetland paddy.
Abstract: Electronic Systems are the core of everyday lives.
They form an integral part in financial networks, mass transit,
telephone systems, power plants and personal computers. Electronic
systems are increasingly based on complex VLSI (Very Large Scale
Integration) integrated circuits. Initial electronic design automation is
concerned with the design and production of VLSI systems. The next
important step in creating a VLSI circuit is Physical Design. The
input to the physical design is a logical representation of the system
under design. The output of this step is the layout of a physical
package that optimally or near optimally realizes the logical
representation. Physical design problems are combinatorial in nature
and of large problem sizes. Darwin observed that, as variations are
introduced into a population with each new generation, the less-fit
individuals tend to extinct in the competition of basic necessities.
This survival of fittest principle leads to evolution in species. The
objective of the Genetic Algorithms (GA) is to find an optimal
solution to a problem .Since GA-s are heuristic procedures that can
function as optimizers, they are not guaranteed to find the optimum,
but are able to find acceptable solutions for a wide range of
problems. This survey paper aims at a study on Efficient Algorithms
for VLSI Physical design and observes the common traits of the
superior contributions.
Abstract: The mixing behaviors of dry and wet granular
materials in gas fluidized bed systems were investigated
computationally using the combined Computational Fluid Dynamics
and Discrete Element Method (CFD-DEM). Dry particles were
observed to mix fairly rapidly during the fluidization process due to
vigorous relative motions between particles induced by the flow of
gas. In contrast, due to the presence of strong cohesive forces arising
from capillary liquid bridges between wet particles, the mixing
efficiencies of wet granular materials under similar operating
conditions were observed to be reduced significantly.
Abstract: Eight heavy metals (Cu, Cr, Zn, Hg, Pb, Cd, Ni and As) were analyzed in sediment samples in the dry and wet seasons from November 2009 to October 2010 in West Port of Peninsular Malaysia. The heavy metal concentrations (mg/kg dry weight) were ranged from 23.4 to 98.3 for Zn, 22.3 to 80 for Pb, 7.4 to 27.6 Cu, 0.244 to 3.53 for Cd, 7.2 to 22.2 for Ni, 20.2 to 162 for As, 0.11 to 0.409 for Hg and 11.5 to 61.5 for Cr. Metals concentrations in dry season were higher than the rainy season except in cupper and chromium. Analysis of variance with Statistical Analysis System (SAS) shows that the mean concentration of metals in the two seasons (α level=0.05) are not significantly different which shows that the metals were held firmly in the matrix of sediment. Also there are significant differences between control point station with other stations. According to the Interim Sediment Quality guidelines (ISQG), the metal concentrations are moderately polluted, except in arsenic which shows the highest level of pollution.
Abstract: This paper presents a research conducted to investigate the effect of mixing process on polypropylene (PP) modified bitumen mixed with well graded aggregate to form modified bituminous concrete mix. Two mode of mixing, namely dry and wet with different concentration of polymer polypropylene was used with 80/100 pen bitumen, to evaluate the bituminous concrete mix properties. Three percentages of polymer varying from 1-3% by the weight of bitumen was used in this study. Three mixes namely control mix, wet mix and dry mix were prepared. Optimum binder content was calculated considering Marshall Stability, flow, air voids and Marshall Quotient at different bitumen content varying from 4% - 6.5% for control, dry and wet mix. Engineering properties thus obtained at the calculated optimum bitumen content revealed that wet mixing process is advantageous in comparison to dry mixing as it increases the stiffness of the mixture with the increase in polymer content in bitumen. Stiffness value for wet mix increases with the increase in polymer content which is beneficial in terms of rutting. 1% PP dry mix also shows enhanced stiffness, with the air void content limited to 4%.The flow behaviour of dry mix doesn't indicate any major difference with the increase in polymer content revealing that polymer acting as an aggregate only without affecting the viscosity of the binder in the mix. Polypropylene (PP) when interacted with 80 pen base bitumen enhances its performance characteristics which were brought about by altered rheological properties of the modified bitumen. The decrease in flow with the increase in binder content reflects the increase in viscosity of binder which induces the plastic flow in the mix. Workability index indicates that wet mix were easy to compact up to desired void ratio in comparison to dry mix samples.
Abstract: Turbine blade cooling is considered as the most
effective way of maintaining high operating temperature making use
of the available materials, and turbine systems with wet compression
have a potential for future power generation because of high efficiency
and high specific power with a relatively low cost. In this paper
performance analysis of wet-compression gas turbine cycle with
turbine blade cooling is carried out. The wet compression process is
analytically modeled based on non-equilibrium droplet evaporation.
Special attention is paid for the effects of pressure ratio and water
injection ratio on the important system variables such as ratio of
coolant fluid flow, fuel consumption, thermal efficiency and specific
power. Parametric studies show that wet compression leads to
insignificant improvement in thermal efficiency but significant
enhancement of specific power in gas turbine systems with turbine
blade cooling.
Abstract: In this study, the transesterification of palm oil with methanol for biodiesel production was studied by using CaO–ZnO as a heterogeneous base catalyst prepared by incipient-wetness impregnation (IWI) and co-precipitation (CP) methods. The reaction parameters considered were molar ratio of methanol to oil, amount of catalyst, reaction temperature, and reaction time. The optimum conditions–15:1 molar ratio of methanol to oil, a catalyst amount of 6 wt%, reaction temperature of 60 °C, and reaction time of 8 h–were observed. The effects of Ca loading, calcination temperature, and catalyst preparation on the catalytic performance were studied. The fresh and spent catalysts were characterized by several techniques, including XRD, TPR, and XRF.
Abstract: In the present study Schwertmannite (an iron oxide
hydroxide) is selected as an adsorbent for defluoridation of water.
The adsorbent was prepared by wet chemical process and was
characterized by SEM, XRD and BET. The fluoride adsorption
efficiency of the prepared adsorbent was determined with respect to
contact time, initial fluoride concentration, adsorbent dose and pH of
the solution. The batch adsorption data revealed that the fluoride
adsorption efficiency was highly influenced by the studied factors.
Equilibrium was attained within one hour of contact time indicating
fast kinetics and the adsorption data followed pseudo second order
kinetic model. Equilibrium isotherm data fitted to both Langmuir and
Freundlich isotherm models for a concentration range of 5-30 mg/L.
The adsorption system followed Langmuir isotherm model with
maximum adsorption capacity of 11.3 mg/g. The high adsorption
capacity of Schwertmannite points towards the potential of this
adsorbent for fluoride removal from aqueous medium.
Abstract: In this research, CaO-ZnO catalysts (with various
Ca:Zn atomic ratios of 1:5, 1:3, 1:1, and 3:1) prepared by incipientwetness
impregnation (IWI) and co-precipitation (CP) methods were
used as a catalyst in the transesterification of palm oil with methanol
for biodiesel production. The catalysts were characterized by several
techniques, including BET method, CO2-TPD, and Hemmett
Indicator. The effects of precursor concentration, and calcination
temperature on the catalytic performance were studied under reaction
conditions of a 15:1 methanol to oil molar ratio, 6 wt% catalyst,
reaction temperature of 60°C, and reaction time of 8 h. At Ca:Zn
atomic ratio of 1:3 gave the highest FAME value owing to a basic
properties and surface area of the prepared catalyst.
Abstract: Dispersions of casein micelles (CM) were studied at a
constant protein concentration of 5 wt % in high NaCl environment
ranging from 0% to 12% by Dynamic light scattering (DLS) and
Fourier Transform Infrared (FTIR). The rehydration profiles obtained
were interpreted in term of wetting, swelling and dispersion stages by
using a turbidity method. Two behaviours were observed depending
on the salt concentration. The first behaviour (low salt concentration)
presents a typical rehydration profile with a significant change
between 3 and 6% NaCl indicating quick wetting, swelling and long
dispersion stage. On the opposite, the dispersion stage of the second
behaviour (high salt concentration) was significantly shortened
indicating a strong modification of the protein backbone. A salt
increase result to a destabilization of the micelle and the formation of
mini-micelles more or less aggregated indicating an average micelles
size ranging from 100 to 200 nm. For the first time, the estimations
of secondary structural elements (irregular, ß-sheet, α-helix and turn)
by the Amide III assignments were correlated with results from
Amide I.
Abstract: Water leakage is a serious problem in the maintenance of a waterworks facility. Monitoring the water flow rate is one way to locate leakage. However, conventional flowmeters such as the wet-type flowmeter and the clamp-on type ultrasonic flowmeter require additional construction for their installation and are therefore quite expensive. This paper proposes a novel estimation system for the flow rate in a water pipeline, which employs a vibration sensor. This assembly can be attached to any water pipeline without the need for additional high-cost construction. The vibration sensor is designed based on a condenser microphone. This sensor detects vibration caused by water flowing through a pipeline. It is possible to estimate the water flow rate by measuring the amplitude of the output signal from the vibration sensor. We confirmed the validity of the proposed sensing system experimentally.
Abstract: The mesoporous MoO3/γ-Al2O3 catalyst was prepared
by incipient wetness impregnation method aiming to investigate the
effect of drying method and molybdenum content on the catalyst
property and performance towards the oxidation of benzothiophene
(BT), dibenzothiophene (DBT) and 4,6-dimethyle dibenzothiophene
(4,6-DMDBT) with H2O2 for deep oxidative desulfurization of diesel
fuel. The catalyst was characterized by XRD, BET, BJH and SEM
method. The catalyst with 10wt.% and 15wt.% Mo content represent
same optimum performance for DBT and 4,6-DMDBT removal, but
a catalyst with 10wt.% Mo has higher efficiency than 15wt.% Mo for
BT conversion. The SEM images show that use of rotary evaporator
in drying step reaches a more homogenous impregnation. The
oxidation reactivity of different sulfur compounds was studied which
followed the order of DBT>4,6-DMDBT>>BT.
Abstract: The importance for manipulating an incorporated
scaffold and directing cell behaviors is well appreciated for tissue
engineering. Here, we developed newly nano-topographic oxidized
silicon nanosponges capable of being various chemical modifications
to provide much insight into the fundamental biology of how cells
interact with their surrounding environment in vitro. A wet etching
technique is exerted to allow us fabricated the silicon nanosponges in a
high-throughput manner. Furthermore, various organo-silane
chemicals enabled self-assembled on the surfaces by vapor deposition.
We have found that Chinese hamster ovary (CHO) cells displayed
certain distinguishable morphogenesis, adherent responses, and
biochemical properties while cultured on these chemical modified
nano-topographic structures in compared with the planar oxidized
silicon counterparts, indicating that cell behaviors can be influenced
by certain physical characteristic derived from nano-topography in
addition to the hydrophobicity of contact surfaces crucial for cell
adhesion and spreading. Of particular, there were predominant
nano-actin punches and slender protrusions formed while cells were
cultured on the nano-topographic structures. This study shed potential
applications of these nano-topographic biomaterials for controlling
cell development in tissue engineering or basic cell biology research.
Abstract: A study concerning the photocatalytic decolourization
of Congo red (CR) dye, over artificial UV irradiation is presented.
Photocatalysts based on a commercial titanium dioxide (TiO2)
modified with transition metals (Ni, Cu and Zn) were used. The
dopage method used was wet impregnation. A TiO2 sample without
salt was subjected to the same hydrothermal treatment to be used as
reference. Congo red solutions to several pH conditions (natural and
basic) were used to evaluate photocatalytic performance of each
doped catalysts. Photodecolourization percentage was measured
spectrofotrometically after 3 h of treatment to 499 nm as response
variable. Kinetics investigations of photodegradation indicated that
reactions obey to Langmuir-Hinshelwood model and pseudo–first
order law. The rate constant studies of photocatalytic decolourization
reactions for Zn–TiO2 and Cu–TiO2 photocatalysts indicated that in
all cases the rate constant of the reaction was higher than that of TiO2
undoped. These results show that nature of the metal modifying the
TiO2 influence on the efficiency of the photocatalyst evaluated in
process. Ni does not present an additional effect compared with TiO2,
while Zn enhances the photoactivity due to its electronic properties.
Abstract: The catalytic dehydroxylation of glycerol to propylene
glycol was investigated over Cu-ZnO/Al2O3 prepared by incipient
wetness impregnation (IWI) method with different purity feedstocks -
refined glycerol and technical grade glycerol. The main purpose is to
investigate the effects of feed impurities that cause the catalyst
deactivation. The prepared catalyst were tested for its catalytic
activity and selectivity in a continuous flow fixed bed reactor at 523
K, 500 psig, H2/feed molar ratio of 4 and WHSV of 3 h-1. The results
showed that conversion of refined glycerol and technical grade
glycerol at time on stream 6 hour are 99% and 71% and selectivity to
propylene glycol are 87% and 56% respectively. The ICP-EOS and
TPO results indicated that the cause of catalyst deactivation was the
amount of impurities in the feedstock. The higher amount of
impurities (especially Na and K) the lower catalytic activity.
Abstract: As the Textile Industry is the second largest industry
in Egypt and as small and medium-sized enterprises (SMEs) make up
a great portion of this industry therein it is essential to apply the
concept of Cleaner Production for the purpose of reducing pollution.
In order to achieve this goal, a case study concerned with ecofriendly
stone-washing of jeans-garments was investigated. A raw
material-substitution option was adopted whereby the toxic
potassium permanganate and sodium sulfide were replaced by the
environmentally compatible hydrogen peroxide and glucose
respectively where the concentrations of both replaced chemicals
together with the operating time were optimized. In addition, a
process-rationalization option involving four additional processes
was investigated. By means of criteria such as product quality,
effluent analysis, mass and heat balance; and cost analysis with the
aid of a statistical model, a process optimization treatment revealed
that the superior process optima were 50%, 0.15% and 50min for
H2O2 concentration, glucose concentration and time, respectively.
With these values the superior process ought to reduce the annual
cost by about EGP 105 relative to the currently used conventional
method.
Abstract: Study was conducted to determine the concentration of
copper, cadmium, lead and zinc in Cabomba furcata that found
abundance in Lake Chini. This aquatic plant was collected randomly
within the lake for heavy metal determination. Water quality
measurement was undertaken in situ for temperature, pH,
conductivity and dissolved oksigen using portable multi sensor probe
YSI model 556. The C. furcata was digested using wet digestion
method and heavy metal concentrations were analysed using Atomic
Absorption Spectrometer (AAS) Perkin Elmer 4100B (flame
method). Result of water quality classify Lake Chini between class II
to class III using Malaysian Water Quality Standard. According to
this standard, Lake Chini has moderate quality, which normal for
natural lake. Heavy metal concentrations in C.furcata were low and
found to be lower than the critical toxic value in aquatic plants. Oneway
ANOVA test indicated the heavy metal concentrations in
C.furcata were significantly differ between sampling location. Water
quality and heavy metal concentrations indicates that Lake Chini was
not receives anthropogenic load from nearby activities.