Abstract: Temperature, relative humidity and overhygroscopic
moisture fields in a sandstone wall provided with interior thermal
insulation were calculated in order to assess the hygric performance
of the retrofitted wall. Computational simulations showed that during
the time period of 10 years which was subject of investigation no
overhygroscopic moisture appeared in the analyzed building
envelope so that it performed in a satisfactory way from the hygric
point of view.
Abstract: Post cracking behavior and load –bearing capacity of
the steel fiber reinforced high-strength concrete (SFRHSC) are
dependent on the number of fibers are crossing the weakest crack
(bridged the crack) and their orientation to the crack surface. Filling
the mould by SFRHSC, fibers are moving and rotating with the
concrete matrix flow till the motion stops in each internal point of the
concrete body. Filling the same mould from the different ends
SFRHSC samples with the different internal structures (and different
strength) can be obtained. Numerical flow simulations (using Newton
and Bingham flow models) were realized, as well as single fiber
planar motion and rotation numerical and experimental investigation
(in viscous flow) was performed. X-ray pictures for prismatic
samples were obtained and internal fiber positions and orientations
were analyzed. Similarly fiber positions and orientations in cracked
cross-section were recognized and were compared with numerically
simulated. Structural SFRHSC fracture model was created based on
single fiber pull-out laws, which were determined experimentally.
Model predictions were validated by 15x15x60cm prisms 4 point
bending tests.
Abstract: Opportunistic network is a kind of Delay Tolerant Networks (DTN) where the nodes in this network come into contact with each other opportunistically and communicate wirelessly and, an end-to-end path between source and destination may have never existed, and disconnection and reconnection is common in the network. In such a network, because of the nature of opportunistic network, perhaps there is no a complete path from source to destination for most of the time and even if there is a path; the path can be very unstable and may change or break quickly. Therefore, routing is one of the main challenges in this environment and, in order to make communication possible in an opportunistic network, the intermediate nodes have to play important role in the opportunistic routing protocols. In this paper we proposed an Adaptive Fuzzy Routing in opportunistic network (AFRON). This protocol is using the simple parameters as input parameters to find the path to the destination node. Using Message Transmission Count, Message Size and Time To Live parameters as input fuzzy to increase delivery ratio and decrease the buffer consumption in the all nodes of network.
Abstract: Solar sunspot rotation, latitudinal bands are studied based on intelligent computation methods. A combination of image fusion method with together tree decomposition is used to obtain quantitative values about the latitudes of trajectories on sun surface that sunspots rotate around them. Daily solar images taken with SOlar and Heliospheric (SOHO) satellite are fused for each month separately .The result of fused image is decomposed with Quad Tree decomposition method in order to achieve the precise information about latitudes of sunspot trajectories. Such analysis is useful for gathering information about the regions on sun surface and coordinates in space that is more expose to solar geomagnetic storms, tremendous flares and hot plasma gases permeate interplanetary space and help human to serve their technical systems. Here sunspot images in September, November and October in 2001 are used for studying the magnetic behavior of sun.
Abstract: This paper presents an overview of current municipal
solid waste management in Khoram Abad city.
According to data collected by the local authorities, the waste
generation rate is estimated to be 800 g/cap.d with density of 243
kg/m3. Solid waste is stored in different types of containers at the
source of generation in different areas of the city.
Local Authority is responsible for waste collection, transportation.
Municipality is responsible for waste collection, using private sector
contracts.
At present, both mechanical and manual methods are used to
collect residential waste. Manual methods of collection are the most
commonly used for waste collection in most parts of the city.
Land filling is the main disposal method in this city. But it has
some obvious problem and deficiencies
The current state of solid waste management has been improved
slightly in the last decade. By more actions can reduce the human and
environmental risks.
Abstract: This paper describes Clinical Document Architecture Release Two (CDA R2) standard and a client application for messaging with SAĞLIK-NET project developed by The Ministry of Health of Turkey. CDA R2 , developed by Health Level 7 (HL7) organization and approved by American National Standards Institute (ANSI) in 2004, to standardize medical information to be able to share semantically and syntactically. In this study, a client application compatible with HL7 V3 for a project named SAĞLIKNET, aimed to build a National Health Information System by Turkey. Moreover, CDA conformance of this application will also be evaluated.
Abstract: Let G be a Hamiltonian graph. A factor F of G is called
a Hamiltonian factor if F contains a Hamiltonian cycle. In this paper,
two sufficient conditions are given, which are two neighborhood
conditions for a Hamiltonian graph G to have a Hamiltonian factor.
Abstract: Mega urban transport projects (MUTPs) are
increasingly being used in urban environments to ameliorate the
problem of congestion. However, a number of problems with regard
to mega projects have been identified. In particular the seemingly
institutionalised over estimation of economic benefits and persistent
cost over runs, could mean that the wrong projects are selected, and
that the projects that are selected cost more than they should. Studies
to date have produced a number of solutions to these problems,
perhaps most notably, the various methods for the inclusion of the
private sector in project provision. However the problems have
shown significant intractability in the face of these solutions. This
paper provides a detailed examination of some of the problems
facing mega projects and then examines Foucault-s theory of
'governmentality' as a possible frame of analysis which might shed
light on the intractability of the problems that have been identified,
through an identification of the art of government in which MUTPs
occur.
Abstract: The demand on High voltage (HV) infrastructures is growing due to the corresponding growth in industries and population. New or upgraded HV infrastructure has safety implications since Transmission mains usually occupy the same easement in the vicinity of neighbouring residents. Transmission mains consist of underground (UG) and overhead (OH) sections and the transition between the UG and OH section is known as the UGOH pole. The existence of two transmission mains in the same easement can dictate to resort to more complicated earthing design in order to mitigate the effect of AC interference, and in some cases it can also necessitates completing a Split Study of the system. This paper provides an overview of the AC interference, Split Study and the earthing of an underground feeder including the UGOH pole .In addition, this paper discusses the use of different link boxes on the UG feeder and presents a case study that represent a clear example of the Ac interference and Split factor. Finally, a few recommendations are provided to achieve a safety zone in the area beyond the boundary of the HV system.
Abstract: Among many agro- based cottage industries in India
sericulture has been promoted as an agro-based, labor intensive, rural
oriented cottage industry, providing gainful employment mainly to
the weaker and marginalized section of the society specially tribal.
Sericulture occupies the place of pride in the rural economy can be
practiced even with very low land holding, low gestation, high
returns make sericulture an ideal program, requiring little capital
investment. In 2010-2011 the employment in sericulture sector was
72.5 lakh persons. The involvement of landless rural people in tasar
sericulture is because they understood its potential for rural and tribal
upliftment. This article demonstrates that certain developmental
initiatives have been playing an important role in the socio-economic
progress of tribal masses in Raigarh district and explains the
increased returns from sericulture as a result of development
programs. The study concludes with some suggestions to improve the
long term feasibility of sericulture.
Abstract: Von Willebrand-s disease is the most common
inherited bleeding disorder in humans, it
caused by qualitative abnormalities of the von Willebrand factor
(vWF). Our objective is to determine the prevalence of this disease at
part of the Algerian population in the East and the South by a
biological diagnosis based on specific biological tests (automated
platelet count, the bleeding time (TS), the time of cephalin + activator
(TCA), measure of the prothrombin rate (TP), vWF rate and factor
VIII rate, Molecular electrophoresis of vWF multimers in agarose gel
in the presence of SDS). Four patients of type III or severe
Willebrand-s disease were found on 200 suspect cases. All cases are
showed a deficit in vWF rate (< 5%), and factor VIII (P
Abstract: This paper presents a modified version of the
maximum urgency first scheduling algorithm. The maximum
urgency algorithm combines the advantages of fixed and dynamic
scheduling to provide the dynamically changing systems with
flexible scheduling. This algorithm, however, has a major
shortcoming due to its scheduling mechanism which may cause a
critical task to fail. The modified maximum urgency first scheduling
algorithm resolves the mentioned problem. In this paper, we propose
two possible implementations for this algorithm by using either
earliest deadline first or modified least laxity first algorithms for
calculating the dynamic priorities. These two approaches are
compared together by simulating the two algorithms. The earliest
deadline first algorithm as the preferred implementation is then
recommended. Afterwards, we make a comparison between our
proposed algorithm and maximum urgency first algorithm using
simulation and results are presented. It is shown that modified
maximum urgency first is superior to maximum urgency first, since it
usually has less task preemption and hence, less related overhead. It
also leads to less failed non-critical tasks in overloaded situations.
Abstract: Rice husk is a lignocellulosic source that can be
converted to ethanol. Three hundreds grams of rice husk was mixed
with 1 L of 0.18 N sulfuric acid solutions then was heated in an
autoclave. The reaction was expected to be at constant temperature
(isothermal), but before that temperature was achieved, reaction has
occurred. The first liquid sample was taken at temperature of 140 0C
and repeated every 5 minute interval. So the data obtained are in the
regions of non-isothermal and isothermal. It was observed that the
degradation has significant effects on the ethanol production. The
kinetic constants can be expressed by Arrhenius equation with the
frequency factors for hydrolysis and sugar degradation of 1.58 x 105
min-1 and 2.29 x 108 L/mole-min, respectively, while the activation
energies are 64,350 J/mole and 76,571 J/mole. The highest ethanol
concentration from fermentation is 1.13% v/v, attained at 220 0C.
Abstract: Verification of real-time software systems can be
expensive in terms of time and resources. Testing is the main method
of proving correctness but has been shown to be a long and time
consuming process. Everyday engineers are usually unwilling to
adopt formal approaches to correctness because of the overhead
associated with developing their knowledge of such techniques.
Performance modelling techniques allow systems to be evaluated
with respect to timing constraints. This paper describes PARTES, a
framework which guides the extraction of performance models from
programs written in an annotated subset of C.
Abstract: Multimedia, as it stands now is perhaps the most
diverse and rich culture around the globe. One of the major needs of
Multimedia is to have a single system that enables people to
efficiently search through their multimedia catalogues. Many
Domain Specific Systems and architectures have been proposed but
up till now no generic and complete architecture is proposed. In this
paper, we have suggested a generic architecture for Multimedia
Database. The main strengths of our architecture besides being
generic are Semantic Libraries to reduce semantic gap, levels of
feature extraction for more specific and detailed feature extraction
according to classes defined by prior level, and merging of two types
of queries i.e. text and QBE (Query by Example) for more accurate
yet detailed results.
Abstract: The objective of this research was to determine the
potency of indigenous acid-aluminium tolerant Bradyrhizobium
japonicum as producer of indole acetic acid (IAA) and applied it as
nitrogen fixation on local soybeans viz Anjasmoro, Tanggamus
(yellow soybean seeds), and Detam (black soybean seed). Three
isolates of acid-aluminium tolerant Bradyrhizobium japonicum (BJ)
were used in this research, i.e. BJ 11 (wt), BJ 11 (19) - BJ 11(wt)
mutant, and USDA 110 as a reference isolate. All of isolates tested to
produce the IAA by using Salkowsky method. Effect of IAA
production by each of B. japonicum was tested on growth pouch and
greenhouse using three varieties of soybean. All isolates could grow
well and produce IAA on yeast mannitol broth (YMB) medium in
the presence of 0.5 mM L-tryptophan. BJ 11 (19) produced the
highest of IAA at 4 days incubation compared to BJ 11 (wt) and
USDA 110. All tested isolates of Bradyrhizobium japonicum have
showed effect on stimulating the formation of root nodules in
soybean varieties grown on Leonard bottle. The concentration of
IAA on root nodules of soybean symbiotic with B. japonicum was
significantly different with control, except on the treatment using
Tanggamus soybean.
Abstract: In this paper we study some numerical methods to solve a model one-dimensional convection–diffusion equation. The semi-discretisation of the space variable results into a system of ordinary differential equations and the solution of the latter involves the evaluation of a matrix exponent. Since the calculation of this term is computationally expensive, we study some methods based on Krylov subspace and on Restrictive Taylor series approximation respectively. We also consider the Chebyshev Pseudospectral collocation method to do the spatial discretisation and we present the numerical solution obtained by these methods.
Abstract: In this paper, Neuro-Fuzzy based Fuzzy Subtractive
Clustering Method (FSCM) and Self Tuning Fuzzy PD-like
Controller (STFPDC) were used to solve non-linearity and trajectory
problems of pitch AND yaw angles of Twin Rotor MIMO system
(TRMS). The control objective is to make the beams of TRMS reach
a desired position quickly and accurately. The proposed method
could achieve control objectives with simpler controller. To simplify
the complexity of STFPDC, ANFIS based FSCM was used to
simplify the controller and improve the response. The proposed
controllers could achieve satisfactory objectives under different input
signals. Simulation results under MATLAB/Simulink® proved the
improvement of response and superiority of simplified STFPDC on
Fuzzy Logic Controller (FLC).
Abstract: The nature of wireless ad hoc and sensor networks
make them very attractive to attackers. One of the most popular and
serious attacks in wireless ad hoc networks is wormhole attack and
most proposed protocols to defend against this attack used
positioning devices, synchronized clocks, or directional antennas.
This paper analyzes the nature of wormhole attack and existing
methods of defending mechanism and then proposes round trip time
(RTT) and neighbor numbers based wormhole detection mechanism.
The consideration of proposed mechanism is the RTT between two
successive nodes and those nodes- neighbor number which is needed
to compare those values of other successive nodes. The identification
of wormhole attacks is based on the two faces. The first consideration
is that the transmission time between two wormhole attack affected
nodes is considerable higher than that between two normal neighbor
nodes. The second detection mechanism is based on the fact that by
introducing new links into the network, the adversary increases the
number of neighbors of the nodes within its radius. This system does
not require any specific hardware, has good performance and little
overhead and also does not consume extra energy. The proposed
system is designed in ad hoc on-demand distance vector (AODV)
routing protocol and analysis and simulations of the proposed system
are performed in network simulator (ns-2).
Abstract: The six sigma method is a project-driven management approach to improve the organization-s products, services, and processes by continually reducing defects in the organization. Understanding the key features, obstacles, and shortcomings of the six sigma method allows organizations to better support their strategic directions, and increasing needs for coaching, mentoring, and training. It also provides opportunities to better implement six sigma projects. The purpose of this paper is the survey of six sigma process and its impact on the organizational productivity. So I have studied key concepts , problem solving process of six sigmaas well as the survey of important fields such as: DMAIC, six sigma and productivity applied programme, and other advantages of six sigma. In the end of this paper, present research conclusions. (direct and positive relation between six sigma and productivity)