Abstract: Cotton, as a strategic crop, plays an important role in providing human food and clothing need, because of its oil, protein, and fiber. Iran has been one of the largest cotton producers in the world in the past, but unfortunately, for economic reasons, its production is reduced now. One of the ways to reduce the cost of cotton production is to expand the mechanization of cotton harvesting. Iranian farmers do not accept the function of cotton harvesters. One reason for this lack of acceptance of cotton harvesting machines is the number of field losses on these machines. So, the majority of cotton fields are harvested by hand. Although the correct setting of the harvesting machine is very important in the cotton losses, the morphological properties of the cotton plant also affect the performance of cotton harvesters. In this study, the effect of some cotton morphological properties such as the height of the cotton plant, number, and length of sympodial and monopodial branches, boll dimensions, boll weight, number of carpels and bracts angle were evaluated on the performance of cotton picker. In this research, the efficiency of John Deere 9920 spindle Cotton picker is investigated on five different Iranian cotton cultivars. The results indicate that there was a significant difference between the five cultivars in terms of machine harvest efficiency. Golestan cultivar showed the best cotton harvester performance with an average of 87.6% of total harvestable seed cotton and Khorshid cultivar had the least cotton harvester performance. The principal component analysis showed that, at 50.76% probability, the cotton picker efficiency is affected by the bracts angle positively and by boll dimensions, the number of carpels and the height of cotton plants negatively. The seed cotton remains (in the plant and on the ground) after harvester in PCA scatter plot were in the same zone with boll dimensions and several carpels.
Abstract: The recommended limit for cadmium concentration in
potable water is less than 0.005 mg/L. A continuous biosorption
process using indigenous red seaweed, Gracilaria corticata, was
performed to remove cadmium from the potable water. The process
was conducted under fixed conditions and the breakthrough curves
were achieved for three consecutive sorption-desorption cycles. A
modeling based on Artificial Neural Network (ANN) was employed
to fit the experimental breakthrough data. In addition, a simplified
semi empirical model, Thomas, was employed for this purpose. It
was found that ANN well described the experimental data (R2>0.99)
while the Thomas prediction were a bit less successful with R2>0.97.
The adjusted design parameters using the nonlinear form of Thomas
model was in a good agreement with the experimentally obtained
ones. The results approve the capability of ANN to predict the
cadmium concentration in potable water.
Abstract: In this study, a mathematical model was proposed and
the accuracy of this model was assessed to predict the growth of
Pseudomonas aeruginosa and rhamnolipid production under nitrogen
limiting (sodium nitrate) fed-batch fermentation. All of the
parameters used in this model were achieved individually without
using any data from the literature.
The overall growth kinetic of the strain was evaluated using a
dual-parallel substrate Monod equation which was described by
several batch experimental data. Fed-batch data under different
glycerol (as the sole carbon source, C/N=10) concentrations and feed
flow rates were used to describe the proposed fed-batch model and
other parameters. In order to verify the accuracy of the proposed
model several verification experiments were performed in a vast
range of initial glycerol concentrations. While the results showed an
acceptable prediction for rhamnolipid production (less than 10%
error), in case of biomass prediction the errors were less than 23%. It
was also found that the rhamnolipid production by P. aeruginosa was
more sensitive at low glycerol concentrations.
Based on the findings of this work, it was concluded that the
proposed model could effectively be employed for rhamnolipid
production by this strain under fed-batch fermentation on up to 80 g l-
1 glycerol.
Abstract: This paper presents an overview of current municipal
solid waste management in Khoram Abad city.
According to data collected by the local authorities, the waste
generation rate is estimated to be 800 g/cap.d with density of 243
kg/m3. Solid waste is stored in different types of containers at the
source of generation in different areas of the city.
Local Authority is responsible for waste collection, transportation.
Municipality is responsible for waste collection, using private sector
contracts.
At present, both mechanical and manual methods are used to
collect residential waste. Manual methods of collection are the most
commonly used for waste collection in most parts of the city.
Land filling is the main disposal method in this city. But it has
some obvious problem and deficiencies
The current state of solid waste management has been improved
slightly in the last decade. By more actions can reduce the human and
environmental risks.