Abstract: Prosperity of electronic equipment in photocopying
environment not only has improved work efficiency, but also has
changed indoor air quality. Considering the number of photocopying
employed, indoor air quality might be worse than in general office
environments. Determining the contribution from any type of
equipment to indoor air pollution is a complex matter. Non-methane
hydrocarbons are known to have an important role on air quality due
to their high reactivity. The presence of hazardous pollutants in
indoor air has been detected in one photocopying shop in Novi Sad,
Serbia. Air samples were collected and analyzed for five days, during
8-hr working time in three time intervals, whereas three different
sampling points were determined. Using multiple linear regression
model and software package STATISTICA 10 the concentrations of
occupational hazards and microclimates parameters were mutually
correlated. Based on the obtained multiple coefficients of
determination (0.3751, 0.2389 and 0.1975), a weak positive
correlation between the observed variables was determined. Small
values of parameter F indicated that there was no statistically
significant difference between the concentration levels of nonmethane
hydrocarbons and microclimates parameters. The results
showed that variable could be presented by the general regression
model: y = b0 + b1xi1+ b2xi2. Obtained regression equations allow to
measure the quantitative agreement between the variables and thus
obtain more accurate knowledge of their mutual relations.
Abstract: Microscopic simulation tool kits allow for
consideration of the two processes of railway operations and the
previous timetable production. Block occupation conflicts on both
process levels are often solved by using defined train priorities. These
conflict resolutions (dispatching decisions) generate reactionary
delays to the involved trains. The sum of reactionary delays is
commonly used to evaluate the quality of railway operations, which
describes the timetable robustness. It is either compared to an
acceptable train performance or the delays are appraised
economically by linear monetary functions. It is impossible to
adequately evaluate dispatching decisions without a well-founded
objective function. This paper presents a new approach for the
evaluation of dispatching decisions. The approach uses mode choice
models and considers the behaviour of the end-customers. These
models evaluate the reactionary delays in more detail and consider
other competing modes of transport. The new approach pursues the
coupling of a microscopic model of railway operations with the
macroscopic choice mode model. At first, it will be implemented for
railway operations process but it can also be used for timetable
production. The evaluation considers the possibility for the customer
to interchange to other transport modes. The new approach starts to
look at rail and road, but it can also be extended to air travel. The
result of mode choice models is the modal split. The reactions by the
end-customers have an impact on the revenue of the train operating
companies. Different purposes of travel have different payment
reserves and tolerances towards late running. Aside from changes to
revenues, longer journey times can also generate additional costs.
The costs are either time- or track-specific and arise from required
changes to rolling stock or train crew cycles. Only the variable values
are summarised in the contribution margin, which is the base for the
monetary evaluation of delays. The contribution margin is calculated
for different possible solutions to the same conflict. The conflict
resolution is optimised until the monetary loss becomes minimal. The
iterative process therefore determines an optimum conflict resolution
by monitoring the change to the contribution margin. Furthermore, a
monetary value of each dispatching decision can also be derived.
Abstract: In order to produce lead free piezoceramics with
optimum piezoelectric and dielectric properties, KNN modified with
Li+ (as an A site dopant) and Sb5+ (as a B site dopant)
(K0.49Na0.49Li0.02) (Nb0.96Sb0.04) O3 (referred as KNLNS in this paper)
have been synthesized using solid state reaction method and
conventional sintering technique. The ceramics were sintered in the
narrow range of 1050°C-1090°C for 2-3 h to get precise information
about sintering parameters. Detailed study of dependence of
microstructural, dielectric and piezoelectric properties on sintering
conditions was then carried out. The study suggests that the volatility
of the highly hygroscopic KNN ceramics is not only sensitive to
sintering temperatures but also to sintering durations. By merely
reducing the sintering duration for a given sintering temperature we
saw an increase in the density of the samples which was supported by
the increase in dielectric constants of the ceramics. And since density
directly or indirectly affects almost all the associated properties, other
dielectric and piezoelectric properties were also enhanced as we
approached towards the most suitable sintering temperature and
duration combination. The detailed results are reported in this paper.
Abstract: With the growing of computer and network, digital
data can be spread to anywhere in the world quickly. In addition,
digital data can also be copied or tampered easily so that the security
issue becomes an important topic in the protection of digital data.
Digital watermark is a method to protect the ownership of digital data.
Embedding the watermark will influence the quality certainly. In this
paper, Vector Quantization (VQ) is used to embed the watermark into
the image to fulfill the goal of data hiding. This kind of watermarking
is invisible which means that the users will not conscious the existing
of embedded watermark even though the embedded image has tiny
difference compared to the original image. Meanwhile, VQ needs a lot
of computation burden so that we adopt a fast VQ encoding scheme by
partial distortion searching (PDS) and mean approximation scheme to
speed up the data hiding process.
The watermarks we hide to the image could be gray, bi-level and
color images. Texts are also can be regarded as watermark to embed.
In order to test the robustness of the system, we adopt Photoshop to
fulfill sharpen, cropping and altering to check if the extracted
watermark is still recognizable. Experimental results demonstrate that
the proposed system can resist the above three kinds of tampering in
general cases.
Abstract: Micro-electromechanical system (MEMS)
accelerometers and gyroscopes are suitable for the inertial navigation
system (INS) of many applications due to low price, small
dimensions and light weight. The main disadvantage in a comparison
with classic sensors is a worse long term stability. The estimation
accuracy is mostly affected by the time-dependent growth of inertial
sensor errors, especially the stochastic errors. In order to eliminate
negative effects of these random errors, they must be accurately
modeled. In this paper, the Allan variance technique will be used in
modeling the stochastic errors of the inertial sensors. By performing
a simple operation on the entire length of data, a characteristic curve
is obtained whose inspection provides a systematic characterization
of various random errors contained in the inertial-sensor output data.
Abstract: The coaxial transformer-coupled push-pull circuitry
has been used widely in HF and VHF amplifiers for many decades
without significant changes in the topology of the transformers. Basic
changes over the years concerned the construction and turns ratio of
the transformers as has been imposed upon the newer technologies
active devices demands. The balun transmission line transformers
applied in push-pull amplifiers enable input/output impedance
transformation, but are mainly used to convert the balanced output
into unbalanced and the input unbalanced into balanced. A simple
and affordable alternative solution over the traditional coaxial
transformer is the coreless planar balun. A key advantage over the
traditional approach lies in the high specifications repeatability;
simplifying the amplifier construction requirements as the planar
balun constitutes an integrated part of the PCB copper layout. This
paper presents the performance analysis of a planar LDMOS
MRFE6VP5600 Push-Pull amplifier that enables robust operation in
Band III, DVB-T, DVB-T2 standards but functions equally well in
Band II, for DRM+ new generation transmitters.
Abstract: The effect of N2 pretreatment on the catalytic activity
of tungsten-based catalysts was investigated in the metathesis of
ethylene and trans-2-butene at 450oC and atmospheric pressure. The
presence of tungsten active species was confirmed by UV-Vis and
Raman spectroscopy. Compared to the WO3-based catalysts treated
in air, higher amount of WO4 2-tetrahedral species and lower amount
of WO3 crystalline species were observed on the N2-treated ones.
These contribute to the higher conversion of 2-butene and propylene
selectivity during 10 h time-on-stream. Moreover, N2 treatment led to
lower amount of coke formation as revealed by TPO of the spent
catalysts.
Abstract: Egg yolk oil is a natural source of bioactive
compounds such as unsaturated fatty acids, oil soluble vitamins,
pigments and others. Bioactive compound content in egg yolk oil
depends from its content in eggs, from which oil was extracted. Many
studies show that bioactive compound content in egg is correlated to
the content of these compounds in hen feed, but there is also an
opinion that hen housing systems also have influence on egg
chemical content. The aim of this study was to determine which
factor, laying hen housing system or hen diet, has a primary influence
on bioactive compound content in egg yolk oil. The egg yolk oil was
extracted from eggs obtained from 4 different hen housing systems:
cage, barn and two groups of free range. All hens were fed with
commercially produced compound feed except one group of free
range hens which get free diet – pastured hens. Extracted egg yolk
oils were analyzed for fatty acids, oil soluble vitamins and β-carotene
content. α-tocopherol, ergocalcipherol and polyunsaturated fatty acid
content in egg yolk oil was higher from eggs obtained from all
housing systems where hens were fed with commercial compound
feed. β-carotene and retinol content in egg yolk oils from free range
free diet eggs was significantly (p>0.05) higher that from other eggs
because hens have access to green forage. Hen physical activity in
free range housing systems decreases content of some bioactive
compound in egg yolk oil.
Abstract: The past two decades, Thailand faced the natural
disasters, for instance, Gay typhoon in 1989, tsunami in 2004, and
huge flood in 2011. The disaster management in Thailand was
improved both structure and mechanism for cope with the natural
disaster since 2007. However, the natural disaster management in
Thailand has various problems, for examples, cooperation between
related an organizations have not unity, inadequate resources, the
natural disaster management of public sectors not proactive, people
has not awareness the risk of the natural disaster, and communities
did not participate in the natural disaster management.
Objective of this study is to find the methods for capacity building
in the natural disaster management of Thailand. The concept and
information about the capacity building and the natural disaster
management of Thailand were reviewed and analyzed by classifying
and organizing data. The result found that the methods for capacity
building in the natural disaster management of Thailand should be
consist of 1) link operation and information in the natural disaster
management between nation, province, local and community levels,
2) enhance competency and resources of public sectors which relate
to the natural disaster management, 3) establish proactive natural
disaster management both planning and implementation, 4)
decentralize the natural disaster management to local government
organizations, 5) construct public awareness in the natural disaster
management to community, 6) support Community Based Disaster
Risk Management (CBDRM) seriously, and 7) emphasis on
participation in the natural disaster management of all stakeholders.
Abstract: In the present work, Electrochemical Impedance
Spectrocopy (EIS) is applied to study the transport of different metal
cations through a cation-exchange membrane. This technique enables
the identification of the ionic-transport characteristics and to
distinguish between different transport mechanisms occurring at
different current density ranges. The impedance spectra are
dependent on the applied dc current density, on the type of cation and
on the concentration.
When the applied dc current density increases, the diameter of the
impedance spectra loops increases because all the components of
membrane system resistance increase. The diameter of the impedance
plots decreases in the order of Na(I), Ni(II) and Cr(III) due to the
increased interactions between the negatively charged sulfonic
groups of the membrane and the cations with greater charge. Nyquist
plots are shifted towards lower values of the real impedance, and its
diameter decreases with the increase of concentration due to the
decrease of the solution resistance.
Abstract: Non contact evaluation of the thickness of paint
coatings can be attempted by different destructive and nondestructive
methods such as cross-section microscopy, gravimetric mass
measurement, magnetic gauges, Eddy current, ultrasound or
terahertz. Infrared thermography is a nondestructive and non-invasive
method that can be envisaged as a useful tool to measure the surface
thickness variations by analyzing the temperature response. In this
paper, the thermal quadrupole method for two layered samples heated
up with a pulsed excitation is firstly used. By analyzing the thermal
responses as a function of thermal properties and thicknesses of both
layers, optimal parameters for the excitation source can be identified.
Simulations show that a pulsed excitation with duration of ten
milliseconds allows obtaining a substrate-independent thermal
response. Based on this result, an experimental setup consisting of a
near-infrared laser diode and an Infrared camera was next used to
evaluate the variation of paint coating thickness between 60 μm and
130 μm on two samples. Results show that the parameters extracted
for thermal images are correlated with the estimated thicknesses by
the Eddy current methods. The laser pulsed thermography is thus an
interesting alternative nondestructive method that can be moreover
used for nonconductive substrates.
Abstract: Coal fly ash is formed as a solid waste product from
the combustion of coal in coal fired power stations. Huge amounts of
fly ash are produced globally every year and are predicted to
increase. Nowadays, less than half of the fly ash is used as a raw
material for cement manufacturing, construction and the rest of it is
disposed as a waste causing yet another environmental concern. For
this reason, the recycling of this kind of slurries into useful materials
is quite important in terms of economical and environmental aspects.
The purpose of this study is to evaluate the Orhaneli and
Tuncbilek coal fly ashes for utilization in some industrial
applications. Therefore the mineralogical and chemical compositions
of these fly ashes were analyzed by X-ray fluorescence spectroscopy,
ourier-transform infrared spectrometer, and X-ray diffraction. The
silicon (Si) and aluminum (Al) in the fly ashes were activated by
alkali fusion technique with sodium hydroxide. The obtained extracts
were analyzed for Si and Al content by inductively coupled plasma
optical emission spectrometry.
Abstract: Chrome tannery wastewater causes serious environmental hazard due to its high pollution potential. As a result, rigorous treatment is necessary for abatement of pollution from this type of wastewater. There are many research studies on chrome tannery wastewater treatment in the field of physical, chemical, and biological methods. In general, biological treatment process is found ineffective for direct application because of adverse effects by toxic chromium, sulphide, chloride etc. However, biological methods were employed mainly for a few sub processes generating significant amount of organic matter and without chromium, chlorides etc. In this context the present paper reviews the characteristics feature and pollution potential of wastewater generated from chrome tannery units and treatment of the same. The different biological processes used earlier and their chronological development for treatment of the chrome tannery wastewater are thoroughly reviewed in this paper. In this regard, the scope of hybrid bioreactor - an advanced technology option has also been explored, as this kind of treatment is well suited for the wastewater having inhibitory substances.
Abstract: In this study, ultrasonic assisted machining (UAM) technique is applied in side-surface milling experiment for glass-ceramic workpiece material. The tungsten carbide cutting-tool with diamond coating is used in conjunction with two kinds of cooling/lubrication mediums such as water-soluble (WS) cutting fluid and minimum quantity lubricant (MQL). Full factorial process parameter combinations on the milling experiments are planned to investigate the effect of process parameters on cutting performance. From the experimental results, it tries to search for the better process parameter combination which the edge-indentation and the surface roughness are acceptable. In the machining experiments, ultrasonic oscillator was used to excite a cutting-tool along the radial direction producing a very small amplitude of vibration frequency of 20KHz to assist the machining process. After processing, toolmaker microscope was used to detect the side-surface morphology, edge-indentation and cutting tool wear under different combination of cutting parameters, and analysis and discussion were also conducted for experimental results. The results show that the main leading parameters to edge-indentation of glass ceramic are cutting depth and feed rate. In order to reduce edge-indentation, it needs to use lower cutting depth and feed rate. Water-soluble cutting fluid provides a better cooling effect in the primary cutting area; it may effectively reduce the edge-indentation and improve the surface morphology of the glass ceramic. The use of ultrasonic assisted technique can effectively enhance the surface finish cleanness and reduce cutting tool wear and edge-indentation.
Abstract: A chromium-loaded ash originating from incineration of tannery sludge under anoxic conditions was mixed with low grade soda-lime glass powder coming from commercial glass bottles. The relative weight proportions of ash over glass powder tested were 30/70, 40/60 and 50/50. The solid mixtures, formed in green state compacts, were sintered at the temperature range of 800o C up to 1200o C. The resulting products were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray spectrometry (EDXS) and micro-indentation. The above methods were employed to characterize the various phases, microstructure and hardness of the produced materials. Thermal treatment at 800o C and 1000o C produced opaque ceramic products composed of a variety of chromium-containing and chromium-free crystalline phases. Thermal treatment at 1200o C gave rise to composite products, where only chromium-containing crystalline phases were detected. Hardness results suggest that specific products are serious candidates for structural applications.
Abstract: Early diagnosis of infection like Hep-B virus in blood
is important for low cost medical treatment. For this purpose, it is
desirable to develop a point of care device which should be able to
detect trace quantities of the target molecule in blood. In this paper,
we report a nanoporous silicon oxide sensor which is capable of
detecting down to 1fM concentration of Hep-B surface antigen in
blood without the requirement of any centrifuge or pre-concentration.
This has been made possible by the presence of resonant peak in the
sensitivity characteristics. This peak is observed to be dependent only
on the concentration of the specific antigen and not on the interfering
species in blood serum. The occurrence of opposite impedance
change within the pores and at the bottom of the pore is responsible
for this effect. An electronic interface has also been designed to
provide a display of the virus concentration.
Abstract: In 2010-2011, the research on zooplankton was
conducted in the southern part of the Baltic Sea to determine seasonal
variability in changes occurring throughout the zooplankton in 2010
and 2011, both in the region of Gdańsk Deep, and in the western part
of Gdańsk Bay. The research in the sea showed that the taxonomic
composition of holoplankton in the southern part of the Baltic Sea
was similar to that recorded in this region for many years. The
maximum values of abundance and biomass of zooplankton both in
the Deep and the Bay of Gdańsk were observed in the summer
season. Copepoda dominated in the composition of zooplankton for
almost the entire study period, while rotifers occurred in larger
numbers only in the summer 2010 in the Gdańsk Deep as well as in
May and July 2010 in the western part of Gdańsk Bay, and
meroplankton – in April 2011.
Abstract: Dental porcelain composites reinforced and toughened
by 20 wt.% tetragonal zirconia (3Y-TZP) were processed by hot
pressing at 1000°C. Two types of particles were tested: yttriastabilized
zirconia (ZrO2–3%Y2O3) agglomerates and pre-sintered
yttria-stabilized zirconia (ZrO2–3%Y2O3) particles. The composites
as well as the reinforcing particles were analyzed by the means of
optical and Scanning Electron Microscopy (SEM), Energy Dispersion
Spectroscopy (EDS) and X-Ray Diffraction (XRD). The mechanical
properties were obtained by the transverse rupture strength test. Wear
tests were also performed on the composites and monolithic
porcelain. The best mechanical results were displayed by the
porcelain reinforced with the pre-sintered ZrO2–3%Y2O3
agglomerates.
Abstract: Experimental production methods of Chevreul’s salt
being an intermediate stage product in copper recovery were
investigated on this article. Chevreul’s salt, Cu2SO3.CuSO3.2H2O,
being a mixed valence copper sulphite compound, has been obtained
by using different methods and reagents. Chevreul’s salt has an
intense brick-red color. It is highly stable and expensive. The
production of Chevreul’s salt plays a key role in hydrometallurgy.
Thermodynamic tendency on precipitation of Chevreul’s salt is
related to pH and temperature. Besides, SO2 gaseous is a versatile
reagent for precipitating of copper sulphites, Using of SO2 for
selective precipitation can be made by appropriate adjustments of pH
and temperature. Chevreul’s salt does not form in acidic solutions if
those solutions contains considerable amount of sulfurous acid. It is
necessary to maintain between pH 2–4.5, because, solubility of
Chevreul’s salt increases with decreasing of pH values. Also, the
region which Chevreul’s salt is stable can be seen from the potentialpH
diagram.
Abstract: Increasing prevalence of childhood obesity has
increased the interest in early and late indicators of gaining weight.
Cell blood counts may be indicators of pro-inflammatory states. The
aim was to evaluate associations of hematological parameters,
including hematocrit (HTC), hemoglobin, blood cell counts and their
indices with the degree of obesity in pediatric population. A total of
249; -139 morbidly obese (MO), 82 healthy normal weight (NW) and
28 overweight (OW) children were included into the scope of the
study. WHO BMI-for age percentiles were used to form age- and sexmatched
groups. Informed consent forms and the Ethics Committee
approval were obtained. Anthropometric measurements were
performed. Hematological parameters were determined. Statistical
analyses were performed using SPSS. The degree for statistical
significance was p≤0.05. Significant differences (p=0.000) between
waist-to-hip ratios and head-to- neck ratios (hnrs) of MO and NW
children were detected. A significant difference between hnrs of OW
and MO children (p=0.000) was observed. Red cell distribution width
(RDW) was higher in OW children than NW group (p=0.030). Such
finding couldn’t be detected between MO and NW groups. Increased
RDW was prominent in OW children. The decrease in mean
corpuscular hemoglobin concentration (MCHC) values in MO
children was sharper than the values in OW children (p=0.006 vs
p=0.042) compared to those in NW group. Statistically higher HTC
levels were observed between MO-NW (p=0.014), but none between
OW-NW. Though the cause-effect relationship between obesity and
erythrocyte indices still needs further investigation, alterations in
RDW, HTC, MCHC during obesity may be of significance in the
early life.