Abstract: Uterine and oviducal fluids are necessary for
capacitation of the spermatozoa and early embryonic development.
The aim of the present study was to determine the effects of estrous
cycle phases (follicular and luteal) on some biological parameters
(enzymes, electrolytes and total proteins) in uterine and oviducal
secretions of ewes. Oviducal and uterine fluids were collected,
diluted and centrifuged. According to our results, concentrations of
GPT, G6PDH, total proteins, K and Na were significantly (P
Abstract: Over 90% of the world trade is carried by the
international shipping industry. As most of the countries are
developing, seaborne trade continues to expand to bring benefits for
consumers across the world. Studies show that world trade will
increase 70-80% through shipping in the next 15-20 years. Present
global fleet of 70000 commercial ships consumes approximately 200
million tonnes of diesel fuel a year and it is expected that it will be
around 350 million tonnes a year by 2020. It will increase the
demand for fuel and also increase the concentration of CO2 in the
atmosphere. So, it-s essential to control this massive fuel
consumption and CO2 emission. The idea is to utilize a diesel-wind
hybrid system for ship propulsion. Use of wind energy by installing
modern wing-sails in ships can drastically reduce the consumption of
diesel fuel. A huge amount of wind energy is available in oceans.
Whenever wind is available the wing-sails would be deployed and
the diesel engine would be throttled down and still the same forward
speed would be maintained. Wind direction in a particular shipping
route is not same throughout; it changes depending upon the global
wind pattern which depends on the latitude. So, the wing-sail
orientation should be such that it optimizes the use of wind energy.
We have made a computer programme in which by feeding the data
regarding wind velocity, wind direction, ship-motion direction; we
can find out the best wing-sail position and fuel saving for
commercial ships. We have calculated net fuel saving in certain
international shipping routes, for instance, from Mumbai in India to
Durban in South Africa. Our estimates show that about 8.3% diesel
fuel can be saved by utilizing the wind. We are also developing an
experimental model of the ship employing airfoils (small scale wingsail)
and going to test it in National Wind Tunnel Facility in IIT
Kanpur in order to develop a control mechanism for a system of
airfoils.
Abstract: Managing knowledge of research is one way to ensure
just in time information and knowledge to support research strategist
and activities. Unfortunately researcher found the vital research
knowledge in IHL (Institutions of Higher Learning) are scattered,
unstructured and unorganized. Aiming on lay aside conceptual
foundations for understanding and developing OMS (Organizational
Memory System) to facilitate research in IHL, this research revealed
ten factors contributed to the needs of research in the IHL and seven
internal challenges of IHL in promoting research to their academic
members. This study then suggested a comprehensive support of
managing research knowledge using Organizational Memory System
(OMS). Eight OMS characteristics to support research were
identified. Finally the initial work in designing OMS was projected
using knowledge taxonomy. All analysis is derived from pertinent
research paper related to research in IHL and OMS. Further study can
be conducted to validate and verify results presented.
Abstract: As new challenges emerge in power electrical
workplace safety, it is the responsibility of the systems designer to
seek out new approaches and solutions that address them. Design
decisions made today will impact cost, safety and serviceability of
the installed systems for 40 or 50 years during the useful life for the
owner. Studies have shown that this cost is an order of magnitude of
7 to 10 times the installed cost of the power distribution equipment.
This paper reviews some aspects of earthing system design in power
substation surrounded by residential houses. The electrical potential
rise and split factors are discussed and a few recommendations are
provided to achieve a safety voltage in the area beyond the boundary
of the substation.
Abstract: Since prestressed concrete members rely on the tensile
strength of the prestressing strands to resist loads, loss of even few
them could result catastrophic. Therefore, it is important to measure
present residual prestress force. Although there are some techniques
for obtaining present prestress force, some problems still remain. One
method is to install load cell in front of anchor head but this may
increase cost. Load cell is a transducer using the elastic material
property. Anchor head is also an elastic material and this might result
in monitoring monitor present prestress force. Features of fiber optic
sensor such as small size, great sensitivity, high durability can assign
sensing function to anchor head. This paper presents the concept of
smart anchor head which acts as load cell and experiment for the
applicability of it. Test results showed the smart anchor head worked
good and strong linear relationship between load and response.
Abstract: In the national and professional music of oral tradition
of many people in the East there is the metric formula called “ussuli",
that is to say rhythmic constructions of different character and a
composition. Ussuli in translation from Arabic means the law. The
cultural contacts of the ancient and medieval inhabitants of the
Central Asia, India, China, East Turkestan, Iraq, Afghanistan,
Turkey, and Iran have played a certain role in formation of both
musical and dancing heritage of each of these people. During
theatrical shows many dances were performed under the
accompaniment of percussion instruments as nagra, dayulpaz, doll.
The abovementioned tools are used as the obligatory accompanying
tool in an orchestra and at support of dancing acts as the solo tool.
Dynamics of development of a dancing composition, at times
execution of technique of movement depends on various
combinations of ussuli and their receptions of execution.
Abstract: One of the essential requirements in order to have a
realistic surgical simulator is real-time interaction by means of a
haptic interface is. In fact, reproducing haptic sensations increases
the realism of the simulation. However, the interaction need to be
performed in real-time, since a delay between the user action and the
system reaction reduces the user immersion. In this paper, we present
a prototype of the coronary stent implant simulator developed in the
HERMES Project; this system allows real-time interactions with a
artery by means of a specific haptic device; thus the user can
interactively navigate in a reconstructed artery and force feedback is
produced when contact occurs between the artery walls and the
medical instruments
Abstract: Fourty one strains of ESBL producing P.aeruginosa
which were previously isolated from burn patients in Kerman
University general hospital, Iran were subjected to PCR, RFLP and
sequencing in order to determine the type of extended spectrum β-
lactamases (ESBL), the restriction digestion pattern and possibility of
mutation among detected genes. DNA extraction was carried out by
phenol chloroform method. PCR for detection of bla genes was
performed using specific primer for each gene. Restriction Fragment
Length Polymorphism (RFLP) for ESBL genes was carried out using
EcoRI, NheI, PVUII, EcoRV, DdeI, and PstI restriction enzymes. The
PCR products were subjected to direct sequencing of both the strands
for identification of the ESBL genes.The blaCTX-M, blaVEB-1, blaPER-1,
blaGES-1, blaOXA-1, blaOXA-4 and blaOXA-10 genes were detected in the
(n=1) 2.43%, (n=41)100%, (n=28) 68.3%, (n=10) 24.4%, (n=29)
70.7%, (n=7)17.1% and (n=38) 92.7% of the ESBL producing isolates
respectively. The RFLP analysis showed that each ESBL gene has
identical pattern of digestion among the isolated strains. Sequencing
of the ESBL genes confirmed the genuinety of PCR products and
revealed no mutation in the restriction sites of the above genes. From
results of the present investigation it can be concluded that blaVEB-1
and blaCTX-M were the most and the least frequently isolated ESBL
genes among the P.aeruginosa strains isolated from burn patients. The
RFLP and sequencing analysis revealed that same clone of the bla
genes were indeed existed among the antibiotic resistant strains.
Abstract: A simple impedance matching technique for inset feed
grooved microstrip patch antenna based on the concept of coplanar
waveguide feed line has been developed and investigated for a
printed antenna at X-Band frequency of 10GHz. The proposed
technique has been used in the design of Linear Grooved Microstrip
patch antenna array. The characteristics of the antenna are
determined in terms of Return loss, VSWR, gain, radiation pattern
etc. The measured and simulated results presented are found to be in
good agreement.
Abstract: In this paper, computational fluid dynamics (CFD) is utilized to characterize a prototype biolistic delivery system, the biomedical device based on the contoured-shock-tube design (CST), with the aim at investigating shocks induced flow instabilities within the contoured shock tube. The shock/interface interactions, the growth of perturbation at an interface between two fluids of different density are interrogated. The key features of the gas dynamics and gas-particle interaction are discussed
Abstract: Urban road network traffic has become one of the
most studied research topics in the last decades. This is mainly due to
the enlargement of the cities and the growing number of motor
vehicles traveling in this road network. One of the most sensitive
problems is to verify if the network is congestion-free. Another
related problem is the automatic reconfiguration of the network
without building new roads to alleviate congestions. These problems
require an accurate model of the traffic to determine the steady state
of the system. An alternative is to simulate the traffic to see if there
are congestions and when and where they occur. One key issue is to
find an adequate model for road intersections. Once the model
established, either a large scale model is built or the intersection is
represented by its performance measures and simulation for analysis.
In both cases, it is important to seek the queueing model to represent
the road intersection. In this paper, we propose to model the road
intersection as a BCMP queueing network and we compare this
analytical model against a simulation model for validation.
Abstract: Prostate cancer is one of the most frequent cancers in men and is a major cause of mortality in the most of countries. In many diagnostic and treatment procedures for prostate disease accurate detection of prostate boundaries in transrectal ultrasound (TRUS) images is required. This is a challenging and difficult task due to weak prostate boundaries, speckle noise and the short range of gray levels. In this paper a novel method for automatic prostate segmentation in TRUS images is presented. This method involves preprocessing (edge preserving noise reduction and smoothing) and prostate segmentation. The speckle reduction has been achieved by using stick filter and top-hat transform has been implemented for smoothing. A feed forward neural network and local binary pattern together have been use to find a point inside prostate object. Finally the boundary of prostate is extracted by the inside point and an active contour algorithm. A numbers of experiments are conducted to validate this method and results showed that this new algorithm extracted the prostate boundary with MSE less than 4.6% relative to boundary provided manually by physicians.
Abstract: This paper presents a novel control strategy of a threephase
four-wire Unified Power Quality (UPQC) for an improvement
in power quality. The UPQC is realized by integration of series and
shunt active power filters (APFs) sharing a common dc bus capacitor.
The shunt APF is realized using a thee-phase, four leg voltage source
inverter (VSI) and the series APF is realized using a three-phase,
three leg VSI. A control technique based on unit vector template
technique (UTT) is used to get the reference signals for series APF,
while instantaneous sequence component theory (ISCT) is used for
the control of Shunt APF. The performance of the implemented
control algorithm is evaluated in terms of power-factor correction,
load balancing, neutral source current mitigation and mitigation of
voltage and current harmonics, voltage sag and swell in a three-phase
four-wire distribution system for different combination of linear and
non-linear loads. In this proposed control scheme of UPQC, the
current/voltage control is applied over the fundamental supply
currents/voltages instead of fast changing APFs currents/voltages,
there by reducing the computational delay and the required sensors.
MATLAB/Simulink based simulations are obtained, which support
the functionality of the UPQC. MATLAB/Simulink based
simulations are obtained, which support the functionality of the
UPQC.
Abstract: The increasing interest on processing data created by
sensor networks has evolved into approaches to implement sensor
networks as databases. The aggregation operator, which calculates a
value from a large group of data such as computing averages or sums,
etc. is an essential function that needs to be provided when
implementing such sensor network databases. This work proposes to
add the DURING clause into TinySQL to calculate values during a
specific long period and suggests a way to implement the aggregation
service in sensor networks by applying materialized view and
incremental view maintenance techniques that is used in data
warehouses. In sensor networks, data values are passed from child
nodes to parent nodes and an aggregation value is computed at the root
node. As such root nodes need to be memory efficient and low
powered, it becomes a problem to recompute aggregate values from all
past and current data. Therefore, applying incremental view
maintenance techniques can reduce the memory consumption and
support fast computation of aggregate values.
Abstract: Considering non-ideal behavior of fluids and its effects on hydrodynamic and mass transfer in multiphase flow is very essential. Simulations were performed that takes into account the effects of mass transfer and mixture non-ideality on hydrodynamics reported by Irani et al. In this paper, by assuming the density of phases to be constant and Raullt-s law instead of using EOS and fugacity coefficient definition, respectively for both the liquid and gas phases, the importance of non-ideality effects on mass transfer and hydrodynamic behavior was studied. The results for a system of octane/propane (T=323 K, P =445 kpa) also indicated that the assumption of constant density in simulation had major role to diverse from experimental data. Furthermore, comparison between obtained results and the previous report indicated significant differences between experimental data and simulation results with more ideal assumptions.
Abstract: According as the Architecture, Engineering and Construction (AEC) Industry projects have grown more complex and larger, the number of utilization of BIM for 3D design and simulation is increasing significantly. Therefore, typical applications of BIM such as clash detection and alternative measures based on 3-dimenstional planning are expanded to process management, cost and quantity management, structural analysis, check for regulation, and various domains for virtual design and construction. Presently, commercial BIM software is operated on single-user environment, so initial cost is so high and the investment may be wasted frequently. Cloud computing that is a next-generation internet technology enables simple internet devices (such as PC, Tablet, Smart phone etc) to use services and resources of BIM software. In this paper, we suggested developing method of the BIM software based on cloud computing environment in order to expand utilization of BIM and reduce cost of BIM software. First, for the benchmarking, we surveyed successful case of BIM and cloud computing. And we analyzed needs and opportunities of BIM and cloud computing in AEC Industry. Finally, we suggested main functions of BIM software based on cloud computing environment and developed a simple prototype of cloud computing BIM software for basic BIM model viewing.
Abstract: As business environments are rapidly changing,
the manufacturing system must be reconfigured to adapt to
various customer needs. In order to cope with this challenge, it
is quintessential to test industrial control logic rapidly and
easily in the design time, and monitor operational behavior in
the run time of automated manufacturing system. Proposed
integrated model for virtual prototyping and operational
monitoring of industrial control logic is to improve limitations
of current ladder programming practices and general discrete
event simulation method. Each plant layout model using HMI
package and object-oriented control logic model is designed
independently and is executed simultaneously in integrated
manner to reflect design practices of automation system in the
design time. Control logic is designed and executed using UML
activity diagram without considering complicated control
behavior to deal with current trend of reconfigurable
manufacturing. After the physical installation, layout model of
virtual prototype constructed in the design time is reused for
operational monitoring of system behavior during run time.
Abstract: System-level design based on high-level abstractions
is becoming increasingly important in hardware and embedded
system design. This paper analyzes meta-design techniques oriented
at developing meta-programs and meta-models for well-understood
domains. Meta-design techniques include meta-programming and
meta-modeling. At the programming level of design process, metadesign
means developing generic components that are usable in a
wider context of application than original domain components. At the
modeling level, meta-design means developing design patterns that
describe general solutions to the common recurring design problems,
and meta-models that describe the relationship between different
types of design models and abstractions. The paper describes and
evaluates the implementation of meta-design in hardware design
domain using object-oriented and meta-programming techniques.
The presented ideas are illustrated with a case study.
Abstract: Today, cancer remains one of the major diseases that
lead to death. The main obstacle in chemotherapy as a main cancer
treatment is the toxicity to normal cells due to Multidrug Resistance
(MDR) after the use of anticancer drugs. Proposed solution to
overcome this problem is the use of MDR efflux inhibitor of cinchona
alkaloids which is delivered together with anticancer drugs
encapsulated in the form of polymeric nanoparticles. The particles
were prepared by the hydration method. The characterization of
nanoparticles was particle size, zeta potential, entrapment efficiency
and in vitro drug release. Combination nanoparticle size ranged 29-45
nm with a neutral surface charge. Entrapment efficiency was above
87% for the use quinine, quinidine or cinchonidine in combination
with etoposide. The release test results exhibited that the cinchona
alkaloids release released faster than that of etoposide. Collectively,
cinchona alkaloids can be packaged along with etoposide in
nanomicelles for better cancer therapy.
Abstract: The purpose of this study was to develop and examine a
Teaching Commitment Scale of Health and Physical Education
(TCS-HPE) for Taiwanese elementary school teachers. First of all,
based on teaching commitment related theory and literatures to
develop a original scale with 40 items, later both stratified random
sampling and cluster sampling were used to sample participants.
During the first stage, 300 teachers were sampled and 251 valid scales
(83.7%) returned. Later, the data was analyzed by exploratory factor
analysis to obtain 74.30% of total variance for the construct validity.
The Cronbach-s alpha coefficient of sum scale reliability was 0.94, and
subscale coefficients were between 0.80 and 0.96. In the second stage,
400 teachers were sampled and 318 valid scales (79.5%) returned.
Finally, this study used confirmatory factor analysis to test validity and
reliability of TCS-HPE. The result showed that the fit indexes reached
acceptable criteria(¤ç2
(246 ) =557.64 , p