Abstract: Recently, as information industry and mobile
communication technology are developing, this study is conducted on
the new concept of intelligent structures and maintenance techniques
that applied wireless sensor network, USN (Ubiquitous Sensor
Network), to social infrastructures such as civil and architectural
structures on the basis of the concept of Ubiquitous Computing that
invisibly provides human life with computing, along with mutually
cooperating, compromising and connecting networks each other by
having computers within all objects around us.
Therefore, the purpose of this study is to investigate the capability
of wireless communication of sensor node embedded in reinforced
concrete structure with a basic experiment on an electric wave
permeability of sensor node by fabricating molding with variables of
concrete thickness and steel bars that are mostly used in constructing
structures to determine the feasibility of application to constructing
structures with USN.
At this time, with putting the pitches of steel bars, the thickness of
concrete placed, and the intensity of RF signal of a
transmitter-receiver as variables and when wireless communication
module was installed inside, the possible communication distance of
plain concrete and the possible communication distance by the pitches
of steel bars was measured in the horizontal and vertical direction
respectively. Besides, for the precise measurement of diminution of an
electric wave, the magnitude of an electric wave in the range of used
frequencies was measured by using Spectrum Analyzer. The
phenomenon of diminution of an electric wave was numerically
analyzed and the effect of the length of wavelength of frequencies was
analyzed by the properties of a frequency band area.
As a result of studying the feasibility of an application to
constructing structures with wireless sensor, in case of plain concrete,
it shows 45cm for the depth of permeability and in case of reinforced
concrete with the pitches of 5cm, it shows 37cm and 45cm for the
pitches of 15cm.
Abstract: For this study, this researcher conducted a precision
network adjustment with QOCA, the precision network adjustment
software developed by Jet Propulsion Laboratory, to perform an
integrated network adjustment on the Unified Control Points managed
by the National Geographic Information Institute. Towards this end,
275 Unified Control Points observed in 2008 were selected before a
network adjustment is performed on those 275 Unified Control Points.
The RMSE on the discrepancies of coordinates as compared to the
results of GLOBK was ±6.07mm along the N axis, ±2.68mm along the
E axis and ±6.49mm along the U axis.
Abstract: In order to provide and maintain effective pedagogy for the burgeoning virtual reality community, it is vital to have trained faculty in the institutions of higher education who will teach these courses and be able to make full use of their academic knowledge and expertise. As the number of online courses continues to grow, there is a need for these institutions to establish mentoring programs that will support the novice online instructor. The environment in which this takes place and the factors that ensure its success are critical to the adoption of the new instructional delivery format taught by both seasoned educators and adjunct instructors. Effective one-on-one mentoring promotes a professional, compassionate and collegial faculty who will provide a consistent and rigorous academic program for students online.
Abstract: In this paper, a new developed construction model of
the UPFC is proposed. The construction of this model consists of one
shunt compensation block and two series compensation blocks. In
this case, the UPFC with the new construction model will be
investigated when it is installed in multi-machine systems with nonlinear
load model. In addition, the steady–state performance of the
new model operating as impedance compensation will be presented
and compared with that obtained from the system without
compensation.
Abstract: We demonstrate a 1×4 coarse wavelength
division-multiplexing (CWDM) planar concave grating
multiplexer/demultiplexer and its application in re-configurable
optical add/drop multiplexer (ROADM) system in silicon-on-insulator
substrate. The wavelengths of the demonstrated concave grating
multiplexer align well with the ITU-T standard. We demonstrate a
prototype of ROADM comprising two such concave gratings and four
wide-band thermo-optical MZI switches. Undercut technology which
removes the underneath silicon substrate is adopted in optical switches
in order to minimize the operation power. For all the thermal heaters,
the operation voltage is smaller than 1.5 V, and the switch power is
~2.4 mW. High throughput pseudorandom binary sequence (PRBS)
data transmission with up to 100 Gb/s is demonstrated, showing the
high-performance ROADM functionality.
Abstract: In the present communication, we have studied
different variations in the entropy measures in the different states of
queueing processes. In case of steady state queuing process, it has
been shown that as the arrival rate increases, the uncertainty
increases whereas in the case of non-steady birth-death process, it is
shown that the uncertainty varies differently. In this pattern, it first
increases and attains its maximum value and then with the passage of
time, it decreases and attains its minimum value.
Abstract: Periodic vortex shedding in pulsating flow inside wavy
channel and the effect it has on heat transfer are studied using the
finite volume method. A sinusoidally-varying component is superimposed
on a uniform flow inside a sinusoidal wavy channel and
the effects on the Nusselt number is analyzed. It was found that a
unique optimum value of the pulsation frequency, represented by the
Strouhal number, exists for Reynolds numbers ranging from 125 to
1000. Results suggest that the gain in heat transfer is related to the
process of vortex formation, movement about the troughs of the wavy
channel, and subsequent ejection/destruction through the converging
section. Heat transfer is the highest when the frequencies of the
pulsation and vortex formation approach being in-phase. Analysis of
Strouhal number effect on Nu over a period of pulsation substantiates
the proposed physical mechanism for enhancement. The effect of
changing the amplitude of pulsation is also presented over a period
of pulsation, showing a monotonic increase in heat transfer with
increasing amplitude. The 60% increase in Nusselt number suggests
that sinusoidal fluid pulsation can an effective method for enhancing
heat transfer in laminar, wavy-channel flows.
Abstract: Contour filter strips planted with perennial vegetation
can be used to improve surface and ground water quality by reducing
pollutant, such as NO3-N, and sediment outflow from cropland to a
river or lake. Meanwhile, the filter strips of perennial grass with biofuel
potentials also have economic benefits of producing ethanol. In
this study, The Soil and Water Assessment Tool (SWAT) model was
applied to the Walnut Creek Watershed to examine the effectiveness
of contour strips in reducing NO3-N outflows from crop fields to the
river or lake. Required input data include watershed topography,
slope, soil type, land-use, management practices in the watershed and
climate parameters (precipitation, maximum/minimum air
temperature, solar radiation, wind speed and relative humidity).
Numerical experiments were conducted to identify potential
subbasins in the watershed that have high water quality impact, and
to examine the effects of strip size and location on NO3-N reduction
in the subbasins under various meteorological conditions (dry,
average and wet). Variable sizes of contour strips (10%, 20%, 30%
and 50%, respectively, of a subbasin area) planted with perennial
switchgrass were selected for simulating the effects of strip size and
location on stream water quality. Simulation results showed that a
filter strip having 10%-50% of the subbasin area could lead to 55%-
90% NO3-N reduction in the subbasin during an average rainfall
year. Strips occupying 10-20% of the subbasin area were found to be
more efficient in reducing NO3-N when placed along the contour
than that when placed along the river. The results of this study can
assist in cost-benefit analysis and decision-making in best water
resources management practices for environmental protection.
Abstract: Gated community has gained its dominant in residential areas development that it has become the standard development pattern of the newly built residential areas in contemporary China. The form of gated community has its own advantages and rationality that meet the needs of quite a lot of residents, but it-s also believed by researchers that the form has great damage to the urban morphology and development, and has a negative impact on residents- living style. However, there is still a considerable controversy of the origins and outcomes. Though recognized as a global phenomenon, gated community developed in China is greatly to do with the specific local forces, respect to the unique historical, political and socio-cultural momentums. A historical review of the traditional settlements in China and the trends that how Gated community has gained its contemporary form, is indispensable for comprehending the local forces, and provide a new perspective to solve the controversy.
Abstract: Sensorized instruments that accurately measure the interaction forces (between biological tissue and instrument endeffector) during surgical procedures offer surgeons a greater sense of immersion during minimally invasive robotic surgery. Although there is ongoing research into force measurement involving surgical graspers little corresponding effort has been carried out on the measurement of forces between scissor blades and tissue. This paper presents the design and development of a force measurement test apparatus, which will serve as a sensor characterization and evaluation platform. The primary aim of the experiments is to ascertain whether the system can differentiate between tissue samples with differing mechanical properties in a reliable, repeatable manner. Force-angular displacement curves highlight trends in the cutting process as well the forces generated along the blade during a cutting procedure. Future applications of the test equipment will involve the assessment of new direct force sensing technologies for telerobotic surgery.
Abstract: In this paper, an efficient structural approach for
recognizing on-line handwritten digits is proposed. After reading
the digit from the user, the slope is estimated and normalized for
adjacent nodes. Based on the changing of signs of the slope values,
the primitives are identified and extracted. The names of these
primitives are represented by strings, and then a finite state
machine, which contains the grammars of the digits, is traced to
identify the digit. Finally, if there is any ambiguity, it will be
resolved. Experiments showed that this technique is flexible and
can achieve high recognition accuracy for the shapes of the digits
represented in this work.
Abstract: The prologue of new High Voltage (HV) transmission
mains into the community necessitates earthing design to ensure
safety compliance of the system. Conductive structures such as steel
or concrete poles are widely used in HV transmission mains. The
earth potential rise (EPR) generated by a fault on these structures
could result to an unsafe condition. This paper discusses information
on the input impedance of the over head earth wire (OHEW) system
for finite and infinite transmission mains. The definition of finite and
infinite system is discussed, maximum EPR due to pole fault. The
simplified equations for EPR assessments are introduced and
discussed for the finite and infinite conditions. A case study is also
shown.
Abstract: Nowadays, organizing a repository of documents and
resources for learning on a special field as Information Technology
(IT), together with search techniques based on domain knowledge or
document-s content is an urgent need in practice of teaching, learning
and researching. There have been several works related to methods of
organization and search by content. However, the results are still
limited and insufficient to meet user-s demand for semantic
document retrieval. This paper presents a solution for the
organization of a repository that supports semantic representation and
processing in search. The proposed solution is a model which
integrates components such as an ontology describing domain
knowledge, a database of document repository, semantic
representation for documents and a file system; with problems,
semantic processing techniques and advanced search techniques
based on measuring semantic similarity. The solution is applied to
build a IT learning materials management system of a university with
semantic search function serving students, teachers, and manager as
well. The application has been implemented, tested at the University
of Information Technology, Ho Chi Minh City, Vietnam and has
achieved good results.
Abstract: Nature conducts its action in a very private manner. To
reveal these actions classical science has done a great effort. But
classical science can experiment only with the things that can be seen
with eyes. Beyond the scope of classical science quantum science
works very well. It is based on some postulates like qubit,
superposition of two states, entanglement, measurement and
evolution of states that are briefly described in the present paper.
One of the applications of quantum computing i.e.
implementation of a novel quantum evolutionary algorithm(QEA) to
automate the time tabling problem of Dayalbagh Educational Institute
(Deemed University) is also presented in this paper. Making a good
timetable is a scheduling problem. It is NP-hard, multi-constrained,
complex and a combinatorial optimization problem. The solution of
this problem cannot be obtained in polynomial time. The QEA uses
genetic operators on the Q-bit as well as updating operator of
quantum gate which is introduced as a variation operator to converge
toward better solutions.
Abstract: Application of nanoparticles as additives in membrane
synthesis for improving the resistance of membranes against fouling
has triggered recent interest in new membrane types. However, most
nanoparticle-enhanced membranes suffer from the tradeoff between
permeability and selectivity. In this study, nano-WS2 was explored as
the additive in membrane synthesis by non-solvent induced phase
separation. Blended PES-WS2 flat-sheet membranes with the
incorporation of ultra-low concentrations of nanoparticles (from 0.025
to 0.25%, WS2/PES ratio) were manufactured and investigated in
terms of permeability, fouling resistance and solute rejection.
Remarkably, a significant enhancement in the permeability was
observed as a result of the incorporation of ultra-low fractions of
nano-WS2 to the membrane structure. Optimal permeability values
were obtained for modified membranes with 0.10%
nanoparticle/polymer concentration ratios. Furthermore, fouling
resistance and solute rejection were significantly improved by the
incorporation of nanoparticles into the membrane matrix. Specifically,
fouling resistance of modified membrane can increase by around 50%.
Abstract: Knowledge management is a process taking any steps
that needed to get the most out of available knowledge resources.
KM involved several steps; capturing the knowledge discovering
new knowledge, sharing the knowledge and applied the knowledge in
the decision making process. In applying the knowledge, it is not
necessary for the individual that use the knowledge to comprehend it
as long as the available knowledge is used in guiding the decision
making and actions. When an expert is called and he provides stepby-
step procedure on how to solve the problems to the caller, the
expert is transferring the knowledge or giving direction to the caller.
And the caller is 'applying' the knowledge by following the
instructions given by the expert. An appropriate mechanism is
needed to ensure effective knowledge transfer which in this case is
by telephone or email. The problem with email and telephone is that
the knowledge is not fully circulated and disseminated to all users. In
this paper, with related experience of local university Help Desk, it is
proposed the usage of Information Technology (IT)to effectively
support the knowledge transfer in the organization. The issues
covered include the existing knowledge, the related works, the
methodology used in defining the knowledge management
requirements as well the overview of the prototype.
Abstract: In this study, we explore the use of information for inventory decision in the healthcare organization (HO). We consider the scenario when the HO can make use of the information collected from some correlated products to enhance its inventory planning. Motivated by our real world observations that HOs adopt RFID and bar-coding system for information collection purpose, we examine the effectiveness of these systems for inventory planning with Bayesian information updating. We derive the optimal ordering decision and study the issue of Pareto improvement in the supply chain. Our analysis demonstrates that RFID system will outperform the bar-coding system when the RFID system installation cost and the tag cost reduce to a level that is comparable with that of the barcoding system. We also show how an appropriately set wholesale pricing contract can achieve Pareto improvement in the HO supply chain.
Abstract: The assessment of surface waters in Enugu metropolis
for fecal coliform bacteria was undertaken. Enugu urban was divided
into three areas (A1, A2 and A3), and fecal coliform bacteria
analysed in the surface waters found in these areas for four years
(2005-2008). The plate count method was used for the analyses. Data
generated were subjected to statistical tests involving; Normality test,
Homogeneity of variance test, correlation test, and tolerance limit
test. The influence of seasonality and pollution trends were
investigated using time series plots. Results from the tolerance limit
test at 95% coverage with 95% confidence, and with respect to EU
maximum permissible concentration show that the three areas suffer
from fecal coliform pollution. To this end, remediation procedure
involving the use of saw-dust extracts from three woods namely;
Chlorophora-Excelsa (C-Excelsa),Khayan-Senegalensis,(CSenegalensis)
and Erythrophylum-Ivorensis (E-Ivorensis) in
controlling the coliforms was studied. Results show that mixture of
the acetone extracts of the woods show the most effective
antibacterial inhibitory activities (26.00mm zone of inhibition)
against E-coli. Methanol extract mixture of the three woods gave best
inhibitory activity (26.00mm zone of inhibition) against S-areus, and
25.00mm zones of inhibition against E-Aerogenes. The aqueous
extracts mixture gave acceptable zones of inhibitions against the
three bacteria organisms.
Abstract: The scenario of bypass transition is generally described
as follows: the low-frequency disturbances in the free-stream may
generate long stream-wise streaks in the boundary layer, which later
may trigger secondary instability, leading to rapid increase of
high-frequency disturbances. Then possibly turbulent spots emerge,
and through their merging, lead to fully developed turbulence. This
description, however, is insufficient in the sense that it does not
provide the inherent mechanism of transition that during the transition,
a large number of waves with different frequencies and wave numbers
appear almost simultaneously, producing sufficiently large Reynolds
stress, so the mean flow profile can change rapidly from laminar to
turbulent. In this paper, such a mechanism will be figured out from
analyzing DNS data of transition.
Abstract: Rapid Prototyping (RP) is a technology that produces models and prototype parts from 3D CAD model data, CT/MRI scan data, and model data created from 3D object digitizing systems. There are several RP process like Stereolithography (SLA), Solid Ground Curing (SGC), Selective Laser Sintering (SLS), Fused Deposition Modeling (FDM), 3D Printing (3DP) among them SLS and FDM RP processes are used to fabricate pattern of custom cranial implant. RP technology is useful in engineering and biomedical application. This is helpful in engineering for product design, tooling and manufacture etc. RP biomedical applications are design and development of medical devices, instruments, prosthetics and implantation; it is also helpful in planning complex surgical operation. The traditional approach limits the full appreciation of various bony structure movements and therefore the custom implants produced are difficult to measure the anatomy of parts and analyze the changes in facial appearances accurately. Cranioplasty surgery is a surgical correction of a defect in cranial bone by implanting a metal or plastic replacement to restore the missing part. This paper aims to do a comparative study on the dimensional error of CAD and SLS RP Models for reconstruction of cranial defect by comparing the virtual CAD with the physical RP model of a cranial defect.