Abstract: Twenty four male Thai native × Anglo-Nubian
crossbred goats were randomly allocated to receive four treatments.
The experiment was conducted for four months and slaughtered that
the Longissimus dorsi muscle was collected for fatty acid analysis.
The results conclude that either castrated method or ages had no
significantly different on monounsaturated fatty acid (MUFA)
(P>0.05) except erucic acid (C22:1n9). Interaction between castrated
method and ages had significantly different in MUFA (P
Abstract: Cements, which are intrinsically brittle materials, can
exhibit a degree of pseudo-ductility when reinforced with a sufficient
volume fraction of a fibrous phase. This class of materials, called
Engineered Cement Composites (ECC) has the potential to be used in
future tunneling applications where a level of pseudo-ductility is
required to avoid brittle failures. However uncertainties remain
regarding mechanical performance. Previous work has focused on
comparatively thin specimens; however for future civil engineering
applications, it is imperative that the behavior in tension of thicker
specimens is understood. In the present work, specimens containing
cement powder and admixtures have been manufactured following
two different processes and tested in tension. Multiple matrix
cracking has been observed during tensile testing, leading to a
“strain-hardening" behavior, confirming the possible suitability of
ECC material when used as thick sections (greater than 50mm) in
tunneling applications.
Abstract: Climate change and environmental pressures are
major international issues nowadays. It is time when governments,
businesses and consumers have to respond through more
environmentally friendly and aware practices, products and policies.
This is the prime time to develop alternative sustainable construction
materials, reduce greenhouse gas emissions, save energy, look to
renewable energy sources and recycled materials, and reduce waste.
The utilization of waste materials (slag, fly ash, glass beads, plastic
and so on) in concrete manufacturing is significant due to its
engineering, financial, environmental and ecological benefits. Thus,
utilization of waste materials in concrete production is very much
helpful to reach the goal of the sustainable construction. Therefore,
this study intends to use glass beads in concrete production.
The paper reports on the performance of 9 different concrete
mixes containing different ratios of glass crushed to 5 mm - 20 mm
maximum size and glass marble of 20 mm size as coarse aggregate.
Ordinary Portland cement type 1 and fine sand less than 0.5 mm were
used to produce standard concrete cylinders. Compressive strength
tests were carried out on concrete specimens at various ages. Test
results indicated that the mix having the balanced ratio of glass beads
and round marbles possess maximum compressive strength which is
3889 psi, as glass beads perform better in bond formation but have
lower strength, on the other hand marbles are strong in themselves
but not good in bonding. These mixes were prepared following a
specific W/C and aggregate ratio; more strength can be expected to
achieve from different W/C, aggregate ratios, adding admixtures like
strength increasing agents, ASR inhibitor agents etc.
Abstract: Manufacturing companies are facing a broad variety
of challenges caused by a dynamic production environment. To
succeed in such an environment, it is crucial to minimize the loss of
time required to trigger the adaptation process of a company-s
production structures. This paper presents an approach for the
continuous monitoring of production structures by neurologic
principles. It enhances classical monitoring concepts, which are
principally focused on reactive strategies, and enables companies to
act proactively. Thereby, strategic aspects regarding the
harmonization of certain life cycles are integrated into the decision
making process for triggering the reconfiguration process of the
production structure.
Abstract: The use of 3D computer-aided design (CAD) models
to support construction project planning has been increasing in the
previous year. 3D CAD models reveal more planning ideas by
visually showing the construction site environment in different stages
of the construction process. Using 3D CAD models together with
scheduling software to prepare construction plan can identify errors
in process sequence and spatial arrangement, which is vital to the
success of a construction project. A number of 4D (3D plus time)
CAD tools has been developed and utilized in different construction
projects due to the awareness of their importance. Virtual prototyping
extends the idea of 4D CAD by integrating more features for
simulating real construction process. Virtual prototyping originates
from the manufacturing industry where production of products such
as cars and airplanes are virtually simulated in computer before they
are built in the factory. Virtual prototyping integrates 3D CAD,
simulation engine, analysis tools (like structural analysis and
collision detection), and knowledgebase to streamline the whole
product design and production process. In this paper, we present the
application of a virtual prototyping software which has been used in
a few construction projects in Hong Kong to support construction
project planning. Specifically, the paper presents an implementation
of virtual prototyping in a residential building project in Hong Kong.
The applicability, difficulties and benefits of construction virtual
prototyping are examined based on this project.
Abstract: In recent years, strategic alliances have taken
increasing importance as a means to control competitive forces and to
enter into new markets. Joint ventures are one of the most frequently
used contractual forms in strategic alliances. There are various
motivations for cooperation between two or more firms e.g.,
accessing to technical know-how, accessing to financial resources
and managing risks. The firms must know about these motivations to
encourage for establishing joint venture. So, it is important for
managers to understand about these motives. On the other hand, the
cooperation section is one of the most effective parts in each country.
In this way, our study identifies goals of joint venture between
cooperative manufacturing firms, and prioritizes those using
TOPSIS1. The results show that the most important of joint venture
goals are: accessing to managerial know-how, sharing total capital
investment.
Abstract: Curing of paints by exposure to UV radiations is
emerging as one of the best film forming technique as an alternative
to traditional solvent borne oxidative and thermal curing coatings.
The composition and chemistry of UV curable coatings and role of
multifunctional and monofunctional monomers, oligomers, and
photoinitiators have been discussed. The limitations imposed by
thermodynamic equilibrium and tendency for acrylic double bond
polymerizations during synthesis of multifunctional acrylates have
been presented. Aim of present investigation was thus to explore the
reaction variables associated with synthesis of multifunctional
acrylates. Zirconium oxychloride was evaluated as catalyst against
regular acid functional catalyst. The catalyzed synthesis of glyceryl
acrylate and neopentyl glycol acrylate was conducted by variation of
following reaction parameters: two different reactant molar ratios-
1:4 and 1:6; catalyst usage in % by moles on polyol- 2.5, 5.0 and 7.5
and two different reaction temperatures- 45 and 75 0C. The reaction
was monitored by determination of acid value and hydroxy value at
regular intervals, besides TLC, HPLC, and FTIR analysis of
intermediates and products. On the basis of determination of reaction
progress over 1-60 hrs, the esterification reaction was observed to
follow 2nd order kinetics with rate constant varying from 1*10-4 to
7*10-4. The thermal and catalytic components of second order rate
constant and energy of activation were also determined. Uses of
these kinetic and thermodynamic parameters in design of reactor for
manufacture of multifunctional acrylate ester have been presented.
The synthesized multifunctional acrylates were used to formulate and
apply UV curable clear coat followed by determination of curing
characteristics and mechanical properties of cured film. The overall
curing rates less than 05 min. were easily attained indicating
economical viability of radiation curable system due to faster
production schedules
Abstract: In today-s competitive global business environment,
the concept of supply chain management (SCM) continues to become
increasingly market-oriented, shifting the primary driver of the value
chain from supply to demand. Recent recommendations encourage
researchers to focus investigations on the supply chain process
integration (SCPI) capabilities that integrate a focal firm with its
network of suppliers and business customers to create value for it.
However, theoretical and empirical researches pertaining to the
antecedents and consequences of a focal firm-s SCPI capabilities have
been limited and piecemeal. The purpose of this study is to investigate
the critical determinants and consequences of a focal firm-s SCPI
capabilities. We test our proposed research framework using a sample
of 139 sales managers of manufacturing industries in Taiwan, our
research findings show that (1) both perceived business customer-s
power and focal firm-s market-oriented culture positively influences a
focal firm-s SCPI capabilities, and (2) SCPI capabilities positively
influence a focal firm-s SCM performance, both operational and
strategic benefits. Implications for practitioners and researchers and
suggestions for future research are also addressed in this study.
Abstract: Flexible manufacturing system is a system that is able to respond to changed conditions. In general, this flexibility is divided into two key categories and several subcategories. The first category is the so called machine flexibility which enables to make various products by the given machinery. The second category is routing flexibility enabling to execute the same operation by various machines. Flexible manufacturing systems usually consist of three main parts: CNC machine tools, transport system and control system. A higher level of flexible manufacturing systems is represented by the so called intelligent manufacturing systems.
Abstract: Manufacturing tolerancing is intended to determine
the intermediate geometrical and dimensional states of the part
during its manufacturing process. These manufacturing dimensions
also serve to satisfy not only the functional requirements given in
the definition drawing, but also the manufacturing constraints, for
example geometrical defects of the machine, vibration and the
wear of the cutting tool. In this paper, an experimental study on the
influence of the wear of the cutting tool (systematic dispersions) is
explored. This study was carried out on three stages .The first stage
allows machining without elimination of dispersions (random,
systematic) so the tolerances of manufacture according to total
dispersions. In the second stage, the results of the first stage are
filtered in such way to obtain the tolerances according to random
dispersions. Finally, from the two previous stages, the systematic
dispersions are generated. The objective of this study is to model
by the least squares method the error of manufacture based on
systematic dispersion. Finally, an approach of optimization of the
manufacturing tolerances was developed for machining on a CNC
machine tool
Abstract: This paper deals about four items assembly process of
linear drive. This assembly will be realized in flexible assembly cell
on Institute of Manufacturing Systems and Applied Mechanics. There
is defined manufacturing cell, individual actuators created our
flexible cell. Next chapter is about control type, detailed describe a
sequence control type, which will be used in mentioned flexible
assembly cell. All cell control is divided in individual steps
instructions. There instructions illustrate table number III.
Abstract: The process of wafer fabrication is arguably the most
technologically complex and capital intensive stage in semiconductor
manufacturing. This large-scale discrete-event process is highly reentrant,
and involves hundreds of machines, restrictions, and
processing steps. Therefore, production control of wafer fabrication
facilities (fab), specifically scheduling, is one of the most challenging
problems that this industry faces. Dispatching rules have been
extensively applied to the scheduling problems in semiconductor
manufacturing. Moreover, lot release policies are commonly used in
this manufacturing setting to further improve the performance of such
systems and reduce its inherent variability. In this work, simulation is
used in the scheduling of re-entrant flow shop manufacturing systems
with an application in semiconductor wafer fabrication; where, a
simulation model has been developed for the Intel Five-Machine Six
Step Mini-Fab using the ExtendTM simulation environment. The
Mini-Fab has been selected as it captures the challenges involved in
scheduling the highly re-entrant semiconductor manufacturing lines.
A number of scenarios have been developed and have been used to
evaluate the effect of different dispatching rules and lot release
policies on the selected performance measures. Results of simulation
showed that the performance of the Mini-Fab can be drastically
improved using a combination of dispatching rules and lot release
policy.
Abstract: The electrolyte stirring method of anodization etching
process for manufacturing porous silicon (PS) is reported in this work.
Two experimental setups of nature air stirring (PS-ASM) and
electrolyte stirring (PS-ESM) are employed to clarify the influence of
stirring mechanisms on electrochemical etching process. Compared to
traditional fabrication without any stirring apparatus (PS-TM), a large
plateau region of PS surface structure is obtained from samples with
both stirring methods by the 3D-profiler measurement. Moreover, the
light emission response is also improved by both proposed electrolyte
stirring methods due to the cycling force in electrolyte could
effectively enhance etch-carrier distribution while the electrochemical
etching process is made. According to the analysis of statistical
calculation of photoluminescence (PL) intensity, lower standard
deviations are obtained from PS-samples with studied stirring methods,
i.e. the uniformity of PL-intensity is effectively improved. The
calculated deviations of PL-intensity are 93.2, 74.5 and 64,
respectively, for PS-TM, PS-ASM and PS-ESM.
Abstract: Apparel product development is an important stage in the life cycle of a product. Shortening this stage will help to reduce the costs of a garment. The aim of this study is to examine the production parameters in knitwear apparel companies by defining the unit costs, and developing a software to calculate the unit costs of garments and make the cost estimates. In this study, with the help of a questionnaire, different companies- systems of unit cost estimating and cost calculating were tried to be analyzed. Within the scope of the questionnaire, the importance of cost estimating process for apparel companies and the expectations from a new cost estimating program were investigated. According to the results of the questionnaire, it was seen that the majority of companies which participated to the questionnaire use manual cost calculating methods or simple Microsoft Excel spreadsheets to make cost estimates. Furthermore, it was discovered that many companies meet with difficulties in archiving the cost data for future use and as a solution to that problem, it is thought that prior to making a cost estimate, sub units of garment costs which are fabric, accessory and the labor costs should be analyzed and added to the database of the programme beforehand. Another specification of the cost estimating unit prepared in this study is that the programme was designed to consist of two main units, one of which makes the product specification and the other makes the cost calculation. The programme is prepared as a web-based application in order that the supplier, the manufacturer and the customer can have the opportunity to communicate through the same platform.
Abstract: Electric vehicle (EV) is one of the effective solutions to
control emission of greenhouses gases in the world. It is of interest
for future transportation due to its sustainability and efficiency by
automotive manufacturers. Various electrical motors have been used
for propulsion system of electric vehicles in last decades. In this
paper brushed DC motor, Induction motor (IM), switched reluctance
motor (SRM) and brushless DC motor (BLDC) are simulated and
compared. BLDC motor is recommended for high performance
electric vehicles. PWM switching technique is implemented for speed
control of BLDC motor. Behavior of different modes of PWM speed
controller of BLDC motor are simulated in MATLAB/SIMULINK.
BLDC motor characteristics are compared and discussed for various
PWM switching modes under normal and inverter fault conditions.
Comparisons and discussions are verified through simulation results.
Abstract: Despite of the preponderant role played by cement among the construction materials, it is today considered as a material destructing the environment due to the large quantities of carbon dioxide exhausted during its manufacture. Besides, global warming is now recognized worldwide as the new threat to the humankind against which advanced countries are investigating measures to reduce the current amount of exhausted gases to the half by 2050. Accordingly, efforts to reduce green gases are exerted in all industrial fields. Especially, the cement industry strives to reduce the consumption of cement through the development of alkali-activated geopolymer mortars using industrial byproducts like bottom ash. This study intends to gather basic data on the flowability and strength development characteristics of alkali-activated geopolymer mortar by examining its FT-IT features with respect to the effects and strength of the alkali-activator in order to develop bottom ash-based alkali-activated geopolymer mortar. The results show that the 35:65 mass ratio of sodium hydroxide to sodium silicate is appropriate and that a molarity of 9M for sodium hydroxide is advantageous. The ratio of the alkali-activators to bottom ash is seen to have poor effect on the strength. Moreover, the FT-IR analysis reveals that larger improvement of the strength shifts the peak from 1060 cm–1 (T-O, T=Si or Al) toward shorter wavenumber.
Abstract: Virtual engineering technology has undergone rapid progress in recent years and is being adopted increasingly by manufacturing companies of many engineering disciplines. There is an increasing demand from industry for qualified virtual engineers. The qualified virtual engineers should have the ability of applying engineering principles and mechanical design methods within the commercial software package environment. It is a challenge to the engineering education in universities which traditionally tends to lack the integration of knowledge and skills required for solving real world problems. In this paper, a case study shows some recent development of a MSc Mechanical Engineering course at Department of Engineering and Technology in MMU, and in particular, two units Simulation of Mechanical Systems(SMS) and Computer Aided Fatigue Analysis(CAFA) that emphasize virtual engineering education and promote integration of knowledge acquisition, skill training and industrial application.
Abstract: An experimental study is realized in order to verify the
Mini Heat Pipe (MHP) concept for cooling high power dissipation
electronic components and determines the potential advantages of
constructing mini channels as an integrated part of a flat heat pipe. A
Flat Mini Heat Pipe (FMHP) prototype including a capillary structure
composed of parallel rectangular microchannels is manufactured and
a filling apparatus is developed in order to charge the FMHP. The
heat transfer improvement obtained by comparing the heat pipe
thermal resistance to the heat conduction thermal resistance of a
copper plate having the same dimensions as the tested FMHP is
demonstrated for different heat input flux rates. Moreover, the heat
transfer in the evaporator and condenser sections are analyzed, and
heat transfer laws are proposed. In the theoretical part of this work, a
detailed mathematical model of a FMHP with axial microchannels is
developed in which the fluid flow is considered along with the heat
and mass transfer processes during evaporation and condensation.
The model is based on the equations for the mass, momentum and
energy conservation, which are written for the evaporator, adiabatic,
and condenser zones. The model, which permits to simulate several
shapes of microchannels, can predict the maximum heat transfer
capacity of FMHP, the optimal fluid mass, and the flow and thermal
parameters along the FMHP. The comparison between experimental
and model results shows the good ability of the numerical model to
predict the axial temperature distribution along the FMHP.
Abstract: There are many expand of Wi-Fi zones provided
mobile careers and usage of wireless access point at home as increase
of usage of wireless internet caused by the use of smart phone. This
paper shows wireless local area network status, security threats of
WLAN and functionality of major wireless access point in Korea. We
propose security countermeasures concerned with life cycle of access
point from manufacturing to installation, using and finally disposal.
There needed to releasing with configured secure at access point.
Because, it is most cost effective resolution than stage of installation or
other life cycle of access point.
Abstract: Greenhouse gases (GHG) emissions impose major
threat to global warming potential (GWP). Unfortunately
manufacturing sector is one of the major sources that contribute
towards the rapid increase in greenhouse gases (GHG) emissions. In
manufacturing sector electric power consumption is the major driver
that influences CO2 emission. Titanium alloys are widely utilized in
aerospace, automotive and petrochemical sectors because of their
high strength to weight ratio and corrosion resistance. Titanium
alloys are termed as difficult to cut materials because of their poor
machinability rating. The present study analyzes energy consumption
during cutting with reference to material removal rate (MRR).
Surface roughness was also measured in order to optimize energy
consumption.