Abstract: This paper presents the experimental results of silicone rubber housing material for 24kV lightning arrester under artificial accelerated ageing test based on IEC 61109 specifications. Specimens having inclined and alternated shed made of HTV silicone rubber with ATH content and having leakage distance 625 mm were tested continuously 1000 hrs in artificial salt fog chamber. After 1000 hrs of salt fog ageing test, obviously surface erosion was observed on trunk between the upper large shed and the lower small shed near the energized end. Decreasing in hydrophobicity and increasing in hardness were measured on tested specimen comparing with new specimen. Chemical analysis by ATR-FTIR confirmed the observation results.
Abstract: Construction site safety in China has aroused
comprehensive concern all over the world. It is imperative to
investigate the main causes of poor construction site safety. This paper
divides all the causes into four aspects, namely the factors of workers,
object, environment and management and sets up the accident causes
element system based on Delphi Method. This is followed by the
application of structural equation modeling to examine the importance
of each aspect of causes from the standpoints of different roles related
to the construction respectively. The results indicate that all the four
aspects of factors are in need of improvement, and different roles have
different ideas considering the priority of those factors. The paper has
instructive significance for the practitioners to take measures to
improve construction site safety in China accordingly.
Abstract: The paper shows the necessity to increase the security
level for paper management in the cadastral field by using specific
graphical watermarks. Using the graphical watermarking will
increase the security in the cadastral content management;
furthermore any altered document will be validated afterwards of its
originality by checking the graphic watermark. If, by any reasons the
document is changed for counterfeiting, it is invalidated and found
that is an illegal copy due to the graphic check of the watermarking,
check made at pixel level
Abstract: The mechanism behind the electromigration and
thermomigration failure in flip-chip solder joints with Cu-pillar bumps
was investigated in this paper through using finite element method.
Hot spot and the current crowding occurrs in the upper corner of
copper column instead of solders of the common solder ball. The
simulation results show that the change in thermal gradient is
noticeable, which might greatly affect the reliability of solder joints
with Cu-pillar bumps under current stressing. When the average
applied current density is increased from 1×104 A/cm2 to 3×104 A/cm2
in solders, the thermal gradient would increase from 74 K/cm to 901
K/cm at an ambient temperature of 25°C. The force from thermal
gradient of 901 K/cm can nearly induce thermomigration by itself.
With the increase in applied current, the thermal gradient is growing. It
is proposed that thermomigration likely causes a serious reliability
issue for Cu column based interconnects.
Abstract: A thirty Rahmani weaned male lambs of average body weight (27.28±1.40 kg) were randomly allotted to three similar groups, ten lambs in each, to study the benefit of commercial feed additives Tonilisat (Saccharomyces cerevisiae) and Roemin W2 (Lactobacillus acidophilus, Lactobacillus thermophilus, Bifidobacterium and Lactose) as growth promoters on lambs performance, digestibility, rumen activity and some blood constituents. The experiment lasted about 107 days. Three experimental groups were allotted as control group: received the basal ration, T1 group: received the basal ration supplemented with Tonilisat as (0.5kg/ ton concentrate feed mixture) and T2 group: received the basal ration supplemented with Roemin W2 (1kg/ ton concentrate feed mixture). Our study revealed that addition of Tonilisat significantly increased digestion coefficient of crude protein than that of the control group, Furthermore, the supplementation of Tonilisat or Roemin W2 increased (p
Abstract: Natural Language Understanding Systems (NLU) will not be widely deployed unless they are technically mature and cost effective to develop. Cost effective development hinges on the availability of tools and techniques enabling the rapid production of NLU applications through minimal human resources. Further, these tools and techniques should allow quick development of applications in a user friendly way and should be easy to upgrade in order to continuously follow the evolving technologies and standards. This paper presents a visual tool for the structuring and editing of dialog forms, the key element of driving conversation in NLU applications based on IBM technology. The main focus is given on the basic component used to describe Human – Machine interactions of that kind, the Dialogue Manager. In essence, the description of a tool that enables the visual representation of the Dialogue Manager mainly during the implementation phase is illustrated.
Abstract: Aluminum alloy has an extensive range of industrial application due to its consistent mechanical properties and structural integrity. The heat treatment by precipitation technique affected the Magnesium, Silicon Manganese and copper crystals dissolved in the Aluminum alloy. The crystals dislocated to precipitate on the crystal’s boundaries of the Aluminum alloy when given a thermal energy increased its hardness. In this project various times and temperature were varied to find out the best combination of these variables to increase the precipitation of the metals on the Aluminum crystal’s boundaries which will lead to get the highest hardness. These specimens are then tested for their hardness and tensile strength. It is noticed that when the temperature increases, the precipitation increases and consequently the hardness increases. A threshold temperature value (264C0) of Aluminum alloy should not be reached due to the occurrence of recrystalization which causes the crystal to grow. This recrystalization process affected the ductility of the alloy and decrease hardness. In addition, and while increasing the temperature the alloy’s mechanical properties will decrease. The mechanical properties, namely tensile and hardness properties are investigated according to standard procedures. In this research, different temperature and time have been applied to increase hardening.The highest hardness at 100°c in 6 hours equals to 207.31 HBR, while at the same temperature and time the lowest elongation equals to 146.5.
Abstract: This study describes the preparation of a novel proton
conducting membranes based on bacterial cellulose (BC) modified by
grafting of 2-acrylamido-2-methyl-1 -propanesulfonic acid (AMPS)
through UV-induced graft polymerization. These AMPS-g-BC
membranes have been characterized by various techniques including
FTIR, SEM and TGA, to find their successful grafting of AMPS on
BC, surface morphology and thermal stability, respectively. Physical
properties of AMPS-g-BC membranes have been assessed in terms of
Lamda value( λ ), ion exchange capacity(IEC) and proton
conductivity. The relationship between degree of grafting and AMPS
concentration used for grafting has been determined by weight gain
method. An optimum proton conductivity equal to 2.89x10-2 S cm-1
and IEC value equal to 1.79 mmol g-1 have been obtained when 20
wt% AMPS concentration is used for grafting (i.e. the corresponding
membrane is notated as AMPS20-g-BC).
Abstract: ZnO-SnO2 i.e. Zinc-Tin-Oxide (ZTO) thin films were
deposited on glass substrate with varying concentrations (ZnO:SnO2
- 100:0, 90:10, 70:30 and 50:50 wt.%) at room temperature by flash
evaporation technique. These deposited ZTO film were annealed at
450 0C in vacuum. These films were characterized to study the effect
of annealing on the structural, electrical, and optical properties.
Atomic force microscopy (AFM) and Scanning electron microscopy
(SEM) images manifest the surface morphology of these ZTO thin
films. The apparent growth of surface features revealed the formation
of nanostructure ZTO thin films. The small value of surface
roughness (root mean square RRMS) ensures the usefulness in
optical coatings. The sheet resistance was also found to be decreased
for both types of films with increasing concentration of SnO2. The
optical transmittance found to be decreased however blue shift has
been observed after annealing.
Abstract: Wavelet transforms is a very powerful tools for image compression. One of its advantage is the provision of both spatial and frequency localization of image energy. However, wavelet transform coefficients are defined by both a magnitude and sign. While algorithms exist for efficiently coding the magnitude of the transform coefficients, they are not efficient for the coding of their sign. It is generally assumed that there is no compression gain to be obtained from the coding of the sign. Only recently have some authors begun to investigate the sign of wavelet coefficients in image coding. Some authors have assumed that the sign information bit of wavelet coefficients may be encoded with the estimated probability of 0.5; the same assumption concerns the refinement information bit. In this paper, we propose a new method for Separate Sign Coding (SSC) of wavelet image coefficients. The sign and the magnitude of wavelet image coefficients are examined to obtain their online probabilities. We use the scalar quantization in which the information of the wavelet coefficient to belong to the lower or to the upper sub-interval in the uncertainly interval is also examined. We show that the sign information and the refinement information may be encoded by the probability of approximately 0.5 only after about five bit planes. Two maps are separately entropy encoded: the sign map and the magnitude map. The refinement information of the wavelet coefficient to belong to the lower or to the upper sub-interval in the uncertainly interval is also entropy encoded. An algorithm is developed and simulations are performed on three standard images in grey scale: Lena, Barbara and Cameraman. Five scales are performed using the biorthogonal wavelet transform 9/7 filter bank. The obtained results are compared to JPEG2000 standard in terms of peak signal to noise ration (PSNR) for the three images and in terms of subjective quality (visual quality). It is shown that the proposed method outperforms the JPEG2000. The proposed method is also compared to other codec in the literature. It is shown that the proposed method is very successful and shows its performance in term of PSNR.
Abstract: Due to insufficient frequency band and tremendous growth of the mobile users, complex computation is needed for the use of resources. Long distance communication began with the introduction of telegraphs and simple coded pulses, which were used to transmit short messages. Since then numerous advances have rendered reliable transfer of information both easier and quicker. Wireless network refers to any type of computer network that is wireless, and is commonly associated with a telecommunications network whose interconnections between nodes is implemented without the use of wires. Wireless network can be broadly categorized in infrastructure network and infrastructure less network. Infrastructure network is one in which we have a base station to serve the mobile users and in the infrastructure less network is one in which no infrastructure is available to serve the mobile users this kind of networks are also known as mobile Adhoc networks. In this paper we have simulated the result for different scenarios with protocols like AODV and DSR; we simulated the result for throughput, delay and receiving traffic in the given scenario.
Abstract: Two different superhydrophobic surfaces were
elaborated and their oil repellency behavior was evaluated using
several liquid with different surface tension. A silicone rubber/SiO2
nanocomposite coated (A) on aluminum substrate by “spin-coating"
and the sample B was an anodized aluminum surface covered by
Teflon-like coating. A high static contact angle about ∼162° was
measured for two prepared surfaces on which the water droplet rolloff.
Scanning electron microscopy (SEM) showed the presence of
micro/nanostructures for both sample A and B similar to that of lotus
leaf.
However the sample A presented significantly different behaviour
of wettability against the low surface tension liquid. Sample A has
been wetted totally by oil (dodecan) droplet while sample B showed
oleophobic behaviour. Oleophobic property of Teflon like coating
can be contributed to the presence of CF2 and CF3 functional group
which was shown by XPS analysis.
Abstract: The main objectif of this paper is to present a tool that
we have developed subject to characterize and modelling indoor radio
channel propagation at millimetric wave. The tool is based on the
ray tracing technique (RTT). As, in realistic environment we cannot
neglect the significant impact of Human Body Shadowing and other
objects in motion on indoor 60 GHz propagation channel. Hence,
our proposed model allows a simulation of propagation in a dynamic
indoor environment. First, we describe a model of human body.
Second, RTT with this model is used to simulate the propagation
of millimeter waves in the presence of persons in motion. Results
of the simulation show that this tool gives results in agreement with
those reported in the literature. Specially, the effects of people motion
on temporal channel properties.
Abstract: The parametrical study of Shrouded Contra-rotating
Rotor was done in this paper based on 2D axisymmetric simulations.
The calculations were made with an actuator disk as double rotor
model. It objects to explore and quantify the effects of different shroud
geometry parameters mainly using the performance of power loading
(PL), which could evaluate the whole propulsion system capability as
5 Newtontotal thrust generationfor hover demand. The numerical
results show that:The increase of nozzle radius is desired but limited
by the flow separation, its optimal design is around 1.15 times rotor
radius, the viscosity effects greatly constraint the influence of nozzle
shape, the divergent angle around 10.5° performs best for chosen
nozzle length;The parameters of inlet such as leading edge curvature,
radius and internal shape do not affect thrust great but play an
important role in pressure distribution which could produce most part
of shroud thrust, they should be chosen according to the reduction of
adverse pressure gradients to reduce the risk of boundary separation.
Abstract: The development of One Tambon One Product
(OTOP) became the policy of the government in 1997 after the
former Prime Minister had been in power. The strategy of sections is
currently set for the policy. OTOP has become the part of the way of
community lives around the country. OTOP may be developed under
changing into ASEAN economic community in 2015 because of the
flow of capitals, productions, and many workers in the region. All
sectors are improved for the change. The purposes of study were to
study the strength and weakness of the OTOP-creating process via its
policy and to lead to the strategy to be able to apply before changing.
The methodology is qualitative to study its policy including
document and to interview experienced persons. The findings showed
that the effort of improvement of all sectors obviously involves with
OTOP development. Particularly, the strategic administration of
OTOP is in every level of the state, central sector, region, and
community.
Abstract: The mixture formation prior to the ignition process
plays as a key element in the diesel combustion. Parametric studies of
mixture formation and ignition process in various injection parameter
has received considerable attention in potential for reducing
emissions. Purpose of this study is to clarify the effects of injection
pressure on mixture formation and ignition especially during ignition
delay period, which have to be significantly influences throughout the
combustion process and exhaust emissions. This study investigated
the effects of injection pressure on diesel combustion fundamentally
using rapid compression machine. The detail behavior of mixture
formation during ignition delay period was investigated using the
schlieren photography system with a high speed camera. This method
can capture spray evaporation, spray interference, mixture formation
and flame development clearly with real images. Ignition process and
flame development were investigated by direct photography method
using a light sensitive high-speed color digital video camera. The
injection pressure and air motion are important variable that strongly
affect to the fuel evaporation, endothermic and prolysis process
during ignition delay. An increased injection pressure makes spray tip
penetration longer and promotes a greater amount of fuel-air mixing
occurs during ignition delay. A greater quantity of fuel prepared
during ignition delay period thus predominantly promotes more rapid
heat release.
Abstract: Human immunodeficiency virus infection and
acquired immunodeficiency syndrome is a global pandemic with
cases reporting from virtually every country and continues to be a
common infection in developing country like India.
Microalbuminuria is a manifestation of human immunodeficiency
virus associated nephropathy. Therefore, microalbuminuria may be
an early marker of human immunodeficiency virus associated
nephropathy, and screening for its presence may be beneficial. A
strikingly high prevalence of microalbuminuria among human
immunodeficiency virus infected patients has been described in
various studies. Risk factors for clinically significant proteinuria
include African - American race, higher human immunodeficiency
virus ribonucleic acid level and lower CD4 lymphocyte count. The
cardiovascular risk factors of increased systolic blood pressure and
increase fasting blood sugar level are strongly associated with
microalbuminuria in human immunodeficiency virus patient. These
results suggest that microalbuminuria may be a sign of current
endothelial dysfunction and micro-vascular disease and there is
substantial risk of future cardiovascular disease events. Positive
contributing factors include early kidney disease such as human
immunodeficiency virus associated nephropathy, a marker of end
organ damage related to co morbidities of diabetes or hypertension,
or more diffuse endothelial cells dysfunction. Nevertheless after
adjustment for non human immunodeficiency virus factors, human
immunodeficiency virus itself is a major risk factor. The presence of
human immunodeficiency virus infection is independent risk to
develop microalbuminuria in human immunodeficiency virus patient.
Cardiovascular risk factors appeared to be stronger predictors of
microalbuminuria than markers of human immunodeficiency virus
severity person with human immunodeficiency virus infection and
microalbuminuria therefore appear to potentially bear the burden of
two separate damage related to known vascular end organ damage
related to know vascular risk factors, and human immunodeficiency
virus specific processes such as the direct viral infection of kidney
cells.The higher prevalence of microalbuminuria among the human
immunodeficiency virus infected could be harbinger of future
increased risks of both kidney and cardiovascular disease. Further
study defining the prognostic significance of microalbuminuria
among human immunodeficiency virus infected persons will be
essential. Microalbuminuria seems to be a predictor of cardiovascular
disease in diabetic and non diabetic subjects, hence it can also be
used for early detection of micro vascular disease in human
immunodeficiency virus positive patients, thus can help to diagnose
the disease at the earliest.
Abstract: The nickel and gold nanoclusters as supported
catalysts were analyzed by XAS, XRD and XPS in order to
determine their local, global and electronic structure. The present
study has pointed out a strong deformation of the local structure of
the metal, due to its interaction with oxide supports. The average
particle size, the mean squares of the microstrain, the particle size
distribution and microstrain functions of the supported Ni and Au
catalysts were determined by XRD method using Generalized Fermi
Function for the X-ray line profiles approximation. Based on EXAFS
analysis we consider that the local structure of the investigated
systems is strongly distorted concerning the atomic number pairs.
Metal-support interaction is confirmed by the shape changes of the
probability densities of electron transitions: Ni K edge (1s →
continuum and 2p), Au LIII-edge (2p3/2 → continuum, 6s, 6d5/2 and
6d3/2). XPS investigations confirm the metal-support interaction at
their interface.
Abstract: In this study, stress distributions on dental implants
made of functionally graded biomaterials (FGBM) are investigated
numerically. The implant body is considered to be subjected to axial
compression loads. Numerical problem is assumed to be 2D, and
ANSYS commercial software is used for the analysis. The cross
section of the implant thread varies as varying the height (H) and the
width (t) of the thread. According to thread dimensions of implant
and material properties of FGBM, equivalent stress distribution on
the implant is determined and presented with contour plots along
with the maximum equivalent stress values. As a result, with
increasing material gradient parameter (n), the equivalent stress
decreases, but the minimum stress distribution increases. Maximum
stress values decrease with decreasing implant radius (r). Maximum
von Mises stresses increases with decreasing H when t is constant.
On the other hand, the stress values are not affected by variation of t
in the case of H = constant.
Abstract: Corner detection and optical flow are common techniques for feature-based video stabilization. However, these algorithms are computationally expensive and should be performed at a reasonable rate. This paper presents an algorithm for discarding irrelevant feature points and maintaining them for future use so as to improve the computational cost. The algorithm starts by initializing a maintained set. The feature points in the maintained set are examined against its accuracy for modeling. Corner detection is required only when the feature points are insufficiently accurate for future modeling. Then, optical flows are computed from the maintained feature points toward the consecutive frame. After that, a motion model is estimated based on the simplified affine motion model and least square method, with outliers belonging to moving objects presented. Studentized residuals are used to eliminate such outliers. The model estimation and elimination processes repeat until no more outliers are identified. Finally, the entire algorithm repeats along the video sequence with the points remaining from the previous iteration used as the maintained set. As a practical application, an efficient video stabilization can be achieved by exploiting the computed motion models. Our study shows that the number of times corner detection needs to perform is greatly reduced, thus significantly improving the computational cost. Moreover, optical flow vectors are computed for only the maintained feature points, not for outliers, thus also reducing the computational cost. In addition, the feature points after reduction can sufficiently be used for background objects tracking as demonstrated in the simple video stabilizer based on our proposed algorithm.