Abstract: Multiport diffusers are the effective engineering
devices installed at the modern marine outfalls for the steady
discharge of effluent streams from the coastal plants, such as
municipal sewage treatment, thermal power generation and seawater
desalination. A mathematical model using a two-dimensional
advection-diffusion equation based on a flat seabed and incorporating
the effect of a coastal tidal current is developed to calculate the
compounded concentration following discharges of desalination
brine from a sea outfall with multiport diffusers. The analytical
solutions are computed graphically to illustrate the merging of
multiple brine plumes in shallow coastal waters, and further
approximation will be made to the maximum shoreline's
concentration to formulate dilution of a multiport diffuser discharge.
Abstract: Reinforced Concrete (RC) structures strengthened
with fiber reinforced polymer (FRP) lack in thermal resistance under
elevated temperatures in the event of fire. This phenomenon led to
the lining of strengthened concrete with thin high performance
cementitious composites (THPCC) to protect the substrate against
elevated temperature. Elevated temperature effects on THPCC, based
on different cementitious materials have been studied in the past but
high-alumina cement (HAC)-based THPCC have not been well
characterized. This research study will focus on the THPCC based on
HAC replaced by 60%, 70%, 80% and 85% of ground granulated
blast furnace slag (GGBS). Samples were evaluated by the
measurement of their mechanical strength (28 & 56 days of curing)
after exposed to 400°C, 600°C and 28°C of room temperature for
comparison and corroborated by their microstructure study. Results
showed that among all mixtures, the mix containing only HAC
showed the highest compressive strength after exposed to 600°C as
compared to other mixtures. However, the tensile strength of THPCC
made of HAC and 60% GGBS content was comparable to the
THPCC with HAC only after exposed to 600°C. Field emission
scanning electron microscopy (FESEM) images of THPCC
accompanying Energy Dispersive X-ray (EDX) microanalysis
revealed that the microstructure deteriorated considerably after
exposure to elevated temperatures which led to the decrease in
mechanical strength.
Abstract: Alpfa-fetoprotein and its fragments may be an important vehicle for targeted delivery of radionuclides to the tumor. We investigated the effect of conditions on the labeling of biologically active synthetic peptide based on the (F-afp) with technetium-99m. The influence of the nature of the buffer solution, pH, concentration of reductant, concentration of the peptide and the reaction temperature on the yield of labeling was examined. As a result, the following optimal conditions for labeling of (F-afp) are found: pH 8.5 (phosphate and bicarbonate buffers) and pH from 1.7 to 7.0 (citrate buffer). The reaction proceeds with sufficient yield at room temperature for 30 min at the concentration of SnCl2 and (Fafp) (F-afp) is to be less than 10 mkg/ml and 25 mkg/ml, respectively. Investigations of the test drug accumulation in the tumor cells of human breast cancer were carried out. Results can be assumed that the in vivo study of the (F-afp) in experimental tumor lesions will show concentrations sufficient for imaging these lesions by SPECT.
Abstract: One of the best ways for achievement of conventional
vehicle changing to hybrid case is trustworthy simulation result and
using of driving realities. For this object, in this paper, at first sevendegree-
of-freedom dynamical model of vehicle will be shown. Then
by using of statically model of engine, gear box, clutch, differential,
electrical machine and battery, the hybrid automobile modeling will
be down and forward simulation of vehicle for pedals to wheels
power transformation will be obtained. Then by design of a fuzzy
controller and using the proper rule base, fuel economy and
regenerative braking will be marked. Finally a series of
MATLAB/SIMULINK simulation results will be proved the
effectiveness of proposed structure.
Abstract: As the web continues to grow exponentially, the idea
of crawling the entire web on a regular basis becomes less and less
feasible, so the need to include information on specific domain,
domain-specific search engines was proposed. As more information
becomes available on the World Wide Web, it becomes more difficult
to provide effective search tools for information access. Today,
people access web information through two main kinds of search
interfaces: Browsers (clicking and following hyperlinks) and Query
Engines (queries in the form of a set of keywords showing the topic
of interest) [2]. Better support is needed for expressing one's
information need and returning high quality search results by web
search tools. There appears to be a need for systems that do reasoning
under uncertainty and are flexible enough to recover from the
contradictions, inconsistencies, and irregularities that such reasoning
involves. In a multi-view problem, the features of the domain can be
partitioned into disjoint subsets (views) that are sufficient to learn the
target concept. Semi-supervised, multi-view algorithms, which
reduce the amount of labeled data required for learning, rely on the
assumptions that the views are compatible and uncorrelated. This
paper describes the use of semi-structured machine learning approach
with Active learning for the “Domain Specific Search Engines". A
domain-specific search engine is “An information access system that
allows access to all the information on the web that is relevant to a
particular domain. The proposed work shows that with the help of
this approach relevant data can be extracted with the minimum
queries fired by the user. It requires small number of labeled data and
pool of unlabelled data on which the learning algorithm is applied to
extract the required data.
Abstract: One of the essential requirements for the human
beings is the house for living. This is necessary to make the place of
satisfaction for contemporary houses residents by attention to their
culture. In this article represented the relevant theoretical literature
on cultural symbols by use the architecture semiotic to construct the
houses as a better place for living. In fact, make a place for everyday
life with changing the house to the home is one of the most
challengeable subject for architects all around the world. The target
of this article is to find Cypriot houses cultural symbols that assist
architect to design and build contemporary houses, to make more
satisfaction for its residents according to Cypriot life style and their
culture. This paper is based on researching the effect of cultural
symbols on housing, would require various types of methods.
However, this study focuses on two methods, which are quantitative
and qualitative. The purpose of the case-specific study is to finding
the symbols that used in contemporary houses by attention to the
Cypriot cultural symbols in Famagusta houses.
Abstract: We report a computational study of the spreading
dynamics of a viral infection in a complex (scale-free) network. The
final epidemic size distribution (FESD) was found to be unimodal or
bimodal depending on the value of the basic reproductive
number R0 . The FESDs occurred on time-scales long enough for
intermediate-time epidemic size distributions (IESDs) to be important
for control measures. The usefulness of R0 for deciding on the
timeliness and intensity of control measures was found to be limited
by the multimodal nature of the IESDs and by its inability to inform
on the speed at which the infection spreads through the population. A
reduction of the transmission probability at the hubs of the scale-free
network decreased the occurrence of the larger-sized epidemic events
of the multimodal distributions. For effective epidemic control, an
early reduction in transmission at the index cell and its neighbors was
essential.
Abstract: Data clustering is an important data exploration technique
with many applications in data mining. We present an enhanced
version of the well known single link clustering algorithm. We will
refer to this algorithm as DCBOR. The proposed algorithm alleviates
the chain effect by removing the outliers from the given dataset.
So this algorithm provides outlier detection and data clustering
simultaneously. This algorithm does not need to update the distance
matrix, since the algorithm depends on merging the most k-nearest
objects in one step and the cluster continues grow as long as possible
under specified condition. So the algorithm consists of two phases;
at the first phase, it removes the outliers from the input dataset. At
the second phase, it performs the clustering process. This algorithm
discovers clusters of different shapes, sizes, densities and requires
only one input parameter; this parameter represents a threshold for
outlier points. The value of the input parameter is ranging from 0 to
1. The algorithm supports the user in determining an appropriate
value for it. We have tested this algorithm on different datasets
contain outlier and connecting clusters by chain of density points,
and the algorithm discovers the correct clusters. The results of
our experiments demonstrate the effectiveness and the efficiency of
DCBOR.
Abstract: This paper presents a study of the Taguchi design
application to optimize surface quality in damper inserted end milling
operation. Maintaining good surface quality usually involves
additional manufacturing cost or loss of productivity. The Taguchi
design is an efficient and effective experimental method in which a
response variable can be optimized, given various factors, using
fewer resources than a factorial design. This Study included spindle
speed, feed rate, and depth of cut as control factors, usage of different
tools in the same specification, which introduced tool condition and
dimensional variability. An orthogonal array of L9(3^4)was used;
ANOVA analyses were carried out to identify the significant factors
affecting surface roughness, and the optimal cutting combination was
determined by seeking the best surface roughness (response) and
signal-to-noise ratio. Finally, confirmation tests verified that the
Taguchi design was successful in optimizing milling parameters for
surface roughness.
Abstract: Nozzle is the main part of various spinning systems
such as air-jet and Murata air vortex systems. Recently, many
researchers worked on the usage of the nozzle on different spinning
systems such as conventional ring and compact spinning systems. In
these applications, primary purpose is to improve the yarn quality. In
present study, it was produced the yarns with two different nozzle
types and determined the changes in yarn properties. In order to
explain the effect of the nozzle, airflow structure in the nozzle was
modelled and airflow variables were determined. In numerical
simulation, ANSYS 12.1 package program and Fluid Flow (CFX)
analysis method was used. As distinct from the literature, Shear
Stress Turbulent (SST) model is preferred. And also air pressure at
the nozzle inlet was measured by electronic mass flow meter and
these values were used for the simulation of the airflow. At last, the
yarn was modelled and the area from where the yarn is passing was
included to the numerical analysis.
Abstract: Steel plate shear walls (SPSWs) in buildings are
known to be an effective means for resisting lateral forces. By using
un-stiffened walls and allowing them to buckle, their energy
absorption capacity will increase significantly due to the postbuckling
capacity. The post-buckling tension field action of SPSWs
can provide substantial strength, stiffness and ductility. This paper
presents the Finite Element Analysis of low yield point (LYP) steel
shear walls. In this shear wall system, the LYP steel plate is used for
the steel panel and conventional structural steel is used for boundary
frames. A series of nonlinear cyclic analyses were carried out to
obtain the stiffness, strength, deformation capacity, and energy
dissipation capacity of the LYP steel shear wall. The effect of widthto-
thickness ratio of steel plate on buckling behavior, and energy
dissipation capacities were studied. Good energy dissipation and
deformation capacities were obtained for all models.
Abstract: This experiment was carried out to study the effect of
AMF, drought stress and phosphorus on physiological growth indices of basil at Iran using by a split-plot design with three replications.
The main-plot factor included: two levels of irrigation regimes (control=no drought stress and irrigation after 80 evaporation=
drought stress condition) while the sub-plot factors included
phosphorus (0, 35 and 70 kg/ha) and application and non-application of Glomus fasciculatum. The results showed that total dry matter
(TDM), life area index (LAI), relative growth rate (RGR) and crop growth rate (CGR) were all highly significantly different among the
phosphorus, whereas drought stress had effect of practical
significance on TDM, LAI, RGR and CGR. The results also showed that the highest TDM, LAI, RGR and CGR were obtained from
application of Glomus fasciculatum under no-drought condition.
Abstract: In this study, the effects of machining parameters on
specific energy during surface grinding of 6061Al-SiC35P
composites are investigated. Vol% of SiC, feed and depth of cut were
chosen as process variables. The power needed for the calculation of
the specific energy is measured from the two watt meter method.
Experiments are conducted using standard RSM design called Central
composite design (CCD). A second order response surface model was
developed for specific energy. The results identify the significant
influence factors to minimize the specific energy. The confirmation
results demonstrate the practicability and effectiveness of the
proposed approach.
Abstract: This paper proposes an effective adaptation learning
algorithm based on artificial neural networks for speed control of an
induction motor assumed to operate in a high-performance drives
environment. The structure scheme consists of a neural network
controller and an algorithm for changing the NN weights in order that
the motor speed can accurately track of the reference command. This
paper also makes uses a very realistic and practical scheme to
estimate and adaptively learn the noise content in the speed load
torque characteristic of the motor. The availability of the proposed
controller is verified by through a laboratory implementation and
under computation simulations with Matlab-software. The process is
also tested for the tracking property using different types of reference
signals. The performance and robustness of the proposed control
scheme have evaluated under a variety of operating conditions of the
induction motor drives. The obtained results demonstrate the
effectiveness of the proposed control scheme system performances,
both in steady state error in speed and dynamic conditions, was found
to be excellent and those is not overshoot.
Abstract: In modern agriculture, polymeric hydrogels are
known as a component able to hold an amount of water due to their
3-dimensional network structure and their tendency to absorb water
in humid environments. In addition, these hydrogels are able to
controllably release the fertilisers and pesticides loaded in them.
Therefore, they deliver these materials to the plants' roots and help
them with growing. These hydrogels also reduce the pollution of
underground water sources by preventing the active components
from leaching. In this study, sIPN acrylamide based hydrogels are
synthesised by using acrylamide free radical, potassium acrylate, and
linear polyvinyl alcohol. Ammonium nitrate is loaded in the hydrogel
as the fertiliser. The effect of various amounts of monomers and
linear polymer, measured in molar ratio, on the swelling rate,
equilibrium swelling, and release of ammonium nitrate is studied.
Abstract: In the present article, a new method has been developed to enhance the application of equipment monitoring, which in turn results in improving condition-based maintenance economic impact in an automobile parts manufacturing factory. This study also describes how an effective software with a simple database can be utilized to achieve cost-effective improvements in maintenance performance. The most important results of this project are indicated here: 1. 63% reduction in direct and indirect maintenance costs. 2. Creating a proper database to analyse failures. 3. Creating a method to control system performance and develop it to similar systems. 4. Designing a software to analyse database and consequently create technical knowledge to face unusual condition of the system. Moreover, the results of this study have shown that the concept and philosophy of maintenance has not been understood in most Iranian industries. Thus, more investment is strongly required to improve maintenance conditions.
Abstract: This paper presents the solution of power economic dispatch (PED) problem of generating units with valve point effects and multiple fuel options using Self-Adaptive Differential Evolution (SDE) algorithm. The global optimal solution by mathematical approaches becomes difficult for the realistic PED problem in power systems. The Differential Evolution (DE) algorithm is found to be a powerful evolutionary algorithm for global optimization in many real problems. In this paper the key parameters of control in DE algorithm such as the crossover constant CR and weight applied to random differential F are self-adapted. The PED problem formulation takes into consideration of nonsmooth fuel cost function due to valve point effects and multi fuel options of generator. The proposed approach has been examined and tested with the numerical results of PED problems with thirteen-generation units including valve-point effects, ten-generation units with multiple fuel options neglecting valve-point effects and ten-generation units including valve-point effects and multiple fuel options. The test results are promising and show the effectiveness of proposed approach for solving PED problems.
Abstract: Nanoemulsions are a class of emulsions with a droplet
size in the range of 50–500 nm and have attracted a great deal of
attention in recent years because it is unique characteristics. The
physicochemical properties of nanoemulsion suggests that it can be
successfully used to recover the residual oil which is trapped in the
fine pore of reservoir rock by capillary forces after primary and
secondary recovery. Oil-in-water nanoemulsion which can be formed
by high-energy emulsification techniques using specific surfactants
can reduce oil-water interfacial tension (IFT) by 3-4 orders of
magnitude. The present work is aimed on characterization of oil-inwater
nanoemulsion in terms of its phase behavior, morphological
studies; interfacial energy; ability to reduce the interfacial tension and
understanding the mechanisms of mobilization and displacement of
entrapped oil blobs by lowering interfacial tension both at the
macroscopic and microscopic level. In order to investigate the
efficiency of oil-water nanoemulsion in enhanced oil recovery
(EOR), experiments were performed to characterize the emulsion in
terms of their physicochemical properties and size distribution of the
dispersed oil droplet in water phase. Synthetic mineral oil and a series
of surfactants were used to prepare oil-in-water emulsions.
Characterization of emulsion shows that it follows pseudo-plastic
behaviour and drop size of dispersed oil phase follows lognormal
distribution. Flooding experiments were also carried out in a
sandpack system to evaluate the effectiveness of the nanoemulsion as
displacing fluid for enhanced oil recovery. Substantial additional
recoveries (more than 25% of original oil in place) over conventional
water flooding were obtained in the present investigation.
Abstract: Today with the rapid growth of telecommunications equipment, electronic and developing more and more networks of power, influence of electromagnetic waves on one another has become hot topic discussions. So in this article, this issue and appropriate mechanisms for EMC operations have been presented. First, a source of alternating current (50 Hz) and a clear victim in a certain distance from the source is placed. With this simple model, the effects of electromagnetic radiation from the source to the victim will be investigated and several methods to reduce these effects have been presented. Therefore passive and active shields have been used. In some steps, shielding effectiveness of proposed shields will be compared. . It should be noted that simulations have been done by the finite element method (FEM).
Abstract: In this paper, an algorithm for detecting and attenuating
puff noises frequently generated under the mobile environment is
proposed. As a baseline system, puff detection system is designed
based on Gaussian Mixture Model (GMM), and 39th Mel Frequency
Cepstral Coefficient (MFCC) is extracted as feature parameters. To
improve the detection performance, effective acoustic features for puff
detection are proposed. In addition, detected puff intervals are
attenuated by high-pass filtering. The speech recognition rate was
measured for evaluation and confusion matrix and ROC curve are used
to confirm the validity of the proposed system.