Abstract: In this paper, the experimental design of using the
Taguchi method is employed to optimize the processing parameters in
the plasma arc surface hardening process. The processing parameters
evaluated are arc current, scanning velocity and carbon content of
steel. In addition, other significant effects such as the relation between
processing parameters are also investigated. An orthogonal array,
signal-to-noise (S/N) ratio and analysis of variance (ANOVA) are
employed to investigate the effects of these processing parameters.
Through this study, not only the hardened depth increased and surface
roughness improved, but also the parameters that significantly affect
the hardening performance are identified. Experimental results are
provided to verify the effectiveness of this approach.
Abstract: Capacity and efficiency of any refrigerating system
diminish rapidly as the difference between the evaporating and
condensing temperature is increased by a reduction in the evaporator
temperature. The single stage vapour compression refrigeration
system using various refrigerants are limited to an evaporator
temperature of -40 0C. Below temperature of -40 0C the either
cascade refrigeration system or multi stage vapour compression
system is employed. Present work describes thermal design of
condenser (HTS), cascade condenser and evaporator (LTS) of
R404A-R508B and R410A-R23 cascade refrigeration system. Heat
transfer area of condenser, cascade condenser and evaporator for
both systems are compared and the effect of condenser and
evaporator temperature on heat-transfer area for both systems is
studied under same operating condition. The results shows that the
required heat-transfer area of condenser and cascade condenser for
R410A-R23 cascade system is lower than the R404A-R508B cascade
system but heat transfer area of evaporator is similar for both the
system. The heat transfer area of condenser and cascade condenser
decreases with increase in condenser temperature (Tc), whereas the
heat transfer area of cascade condenser and evaporator increases with
increase in evaporator temperature (Te).
Abstract: Stuck-pipe in drilling operations is one of the most
pressing and expensive problems in the oil industry. This paper
describes a computational simulation and an experimental study of
the hydrodynamic vibrator, which may be used for liquidation of
stuck-pipe problems during well drilling. The work principle of the
vibrator is based upon the known phenomena of Vortex Street of
Karman and the resulting generation of vibrations. We will discuss
the computational simulation and experimental investigations of
vibrations in this device. The frequency of the vibration parameters
has been measured as a function of the wide range Reynolds Number.
The validity of the computational simulation and of the assumptions
on which it is based has been proved experimentally. The
computational simulation of the vibrator work and its effectiveness
was carried out using FLUENT software. The research showed high
degree of congruence with the results of the laboratory tests and
allowed to determine the effect of the granular material features upon
the pipe vibration in the well. This study demonstrates the potential
of using the hydrodynamic vibrator in a well drilling system.
Abstract: Fast delay estimation methods, as opposed to
simulation techniques, are needed for incremental performance
driven layout synthesis. On-chip inductive effects are becoming
predominant in deep submicron interconnects due to increasing clock
speed and circuit complexity. Inductance causes noise in signal
waveforms, which can adversely affect the performance of the circuit
and signal integrity. Several approaches have been put forward which
consider the inductance for on-chip interconnect modelling. But for
even much higher frequency, of the order of few GHz, the shunt
dielectric lossy component has become comparable to that of other
electrical parameters for high speed VLSI design. In order to cope up
with this effect, on-chip interconnect has to be modelled as
distributed RLCG line. Elmore delay based methods, although
efficient, cannot accurately estimate the delay for RLCG interconnect
line. In this paper, an accurate analytical delay model has been
derived, based on first and second moments of RLCG
interconnection lines. The proposed model considers both the effect
of inductance and conductance matrices. We have performed the
simulation in 0.18μm technology node and an error of as low as less
as 5% has been achieved with the proposed model when compared to
SPICE. The importance of the conductance matrices in interconnect
modelling has also been discussed and it is shown that if G is
neglected for interconnect line modelling, then it will result an delay
error of as high as 6% when compared to SPICE.
Abstract: The NGN (Next Generation Network), which can
provide advanced multimedia services over an all-IP based network, has been the subject of much attention for years. While there have
been tremendous efforts to develop its architecture and protocols, especially for IMS, which is a key technology of the NGN, it is far
from being widely deployed. However, efforts to create an advanced
signaling infrastructure realizing many requirements have resulted in a
large number of functional components and interactions between those
components. Thus, the carriers are trying to explore effective ways to
deploy IMS while offering value-added services. As one such
approach, we have proposed a self-organizing IMS. A self-organizing
IMS enables IMS functional components and corresponding physical
nodes to adapt dynamically and automatically based on situation such
as network load and available system resources while continuing IMS
operation. To realize this, service continuity for users is an important
requirement when a reconfiguration occurs during operation. In this
paper, we propose a mechanism that will provide service continuity to
users and focus on the implementation and describe performance
evaluation in terms of number of control signaling and processing time
during reconfiguration
Abstract: The complexity of teaching English in higher
institutions by non-native speakers within a second/foreign language
setting has created continuous discussions and research about
teaching approaches and teaching practises, professional identities
and challenges. In addition, there is a growing awareness that
teaching English within discipline-specific contexts adds up to the
existing complexity. This awareness leads to reassessments,
discussions and suggestions on course design and content and
teaching approaches and techniques. In meeting expectations
teaching at a university specified in a particular discipline such as
engineering, English language educators are not only required to
teach students to be able to communicate in English effectively but
also to teach soft skills such as problem solving skills. This paper is
part of a research conducted to investigate how English language
educators negotiate with the complexities of teaching problem
solving skills through English language teaching at a technical
university. This paper reports the way an English language educator
identified himself and the way he approached his teaching in this
institutional context.
Abstract: In this study a clustering technique has been implemented which is K-Means like with hierarchical initial set (HKM). The goal of this study is to prove that clustering document sets do enhancement precision on information retrieval systems, since it was proved by Bellot & El-Beze on French language. A comparison is made between the traditional information retrieval system and the clustered one. Also the effect of increasing number of clusters on precision is studied. The indexing technique is Term Frequency * Inverse Document Frequency (TF * IDF). It has been found that the effect of Hierarchical K-Means Like clustering (HKM) with 3 clusters over 242 Arabic abstract documents from the Saudi Arabian National Computer Conference has significant results compared with traditional information retrieval system without clustering. Additionally it has been found that it is not necessary to increase the number of clusters to improve precision more.
Abstract: The morphological parameter of a thin film surface
can be characterized by power spectral density (PSD) functions
which provides a better description to the topography than the RMS
roughness and imparts several useful information of the surface
including fractal and superstructure contributions. Through the
present study Nanoparticle copper/carbon composite films were
prepared by co-deposition of RF-Sputtering and RF-PECVD method
from acetylene gas and copper target. Surface morphology of thin
films is characterized by using atomic force microscopy (AFM). The
Carbon content of our films was obtained by Rutherford Back
Scattering (RBS) and it varied from .4% to 78%. The power values of
power spectral density (PSD) for the AFM data were determined by
the fast Fourier transform (FFT) algorithms. We investigate the effect
of carbon on the roughness of thin films surface. Using such
information, roughness contributions of the surface have been
successfully extracted.