Abstract: Permanent rivers are the main sources of renewable
water supply for the croplands under the irrigation and drainage
schemes. They are also the major source of sediment loads transport
into the storage reservoirs of the hydro-electrical dams, diversion
weirs and regulating dams. Sedimentation process results from soil
erosion which is related to poor watershed management and human
intervention ion in the hydraulic regime of the rivers. These could
change the hydraulic behavior and as such, leads to riverbed and river
bank scouring, the consequences of which would be sediment load
transport into the dams and therefore reducing the flow discharge in
water intakes. The present paper investigate sedimentation process
by varying the Manning coefficient "n" by using the SHARC
software along the watercourse in the Dez River. Results indicated
that the optimum "n" within that river range is 0.0315 at which
quantity minimum sediment loads are transported into the Eastern
intake. Comparison of the model results with those obtained by those
from the SSIIM software within the same river reach showed a very
close proximity between them. This suggests a relative accuracy with
which the model can simulate the hydraulic flow characteristics and
therefore its suitability as a powerful analytical tool for project
feasibility studies and project implementation.
Abstract: Applicability of tuning the controller gains for Stewart manipulator using genetic algorithm as an efficient search technique is investigated. Kinematics and dynamics models were introduced in detail for simulation purpose. A PD task space control scheme was used. For demonstrating technique feasibility, a Stewart manipulator numerical-model was built. A genetic algorithm was then employed to search for optimal controller gains. The controller was tested onsite a generic circular mission. The simulation results show that the technique is highly convergent with superior performance operating for different payloads.
Abstract: Laboratory activities have produced benefits in
student learning. With current drives of new technology resources
and evolving era of education methods, renewal status of learning
and teaching in laboratory methods are in progress, for both learners
and the educators. To enhance learning outcomes in laboratory works
particularly in engineering practices and testing, learning via handson
by instruction may not sufficient. This paper describes and
compares techniques and implementation of traditional (expository)
with open-ended laboratory (problem-based) for two consecutive
cohorts studying environmental laboratory course in civil engineering
program. The transition of traditional to problem-based findings and
effect were investigated in terms of course assessment student
feedback survey, course outcome learning measurement and student
performance grades. It was proved that students have demonstrated
better performance in their grades and 12% increase in the course
outcome (CO) in problem-based open-ended laboratory style than
traditional method; although in perception, students has responded
less favorable in their feedback.
Abstract: Primary barrier of membrane type LNG containment system consist of corrugated 304L stainless steel. This 304L stainless steel is austenitic stainless steel which shows different material behaviors owing to phase transformation during the plastic work. Even though corrugated primary barriers are subjected to significant amounts of pre-strain due to press working, quantitative mechanical behavior on the effect of pre-straining at cryogenic temperatures are not available. In this study, pre-strain level and pre-strain temperature dependent tensile tests are carried to investigate mechanical behaviors. Also, constitutive equations with material parameters are suggested for a verification study.
Abstract: Today, the Internet based communication has widen
the opportunity of event monitoring system in the medical field.
There is always a need of analyzing and designing secure and reliable
mobile communication between the hospital and biomedical
engineers mobile units. This study has been carried out to find
possible solution using SIP-based event notification for alerting the
technical staff about the Biomedical Device (BMD) status and
Patients treatment session. The Session Initiation Protocol (SIP) can
be used to create a medical event notification system. SIP can work
on a variety of devices. Its adoption as the protocol of choice for third
generation wireless networks allows for a robust and scalable
environment. One of the advantages of SIP is that it supports personal
mobility through the separation of user addressing and device
addressing. The solution for Telemed alert notification system is
based on SIP - Specific Event Notification. The aim of this project is
to extend mobility service to the hospital technicians who are using
Telemedicine system.
Abstract: This study aims to demonstrate the quantification of
peptides based on isotope dilution surface enhanced Raman
scattering (IDSERS). SERS spectra of phenylalanine (Phe), leucine
(Leu) and two peptide sequences TGQIFK (T13) and
YSFLQNPQTSLCFSESIPTPSNR (T6) as part of the 22-kDa
human growth hormone (hGH) were obtained on Ag-nanoparticle
covered substrates. On the basis of the dominant Phe and Leu
vibrational modes, precise partial least squares (PLS) prediction
models were built enabling the determination of unknown T13 and
T6 concentrations. Detection of hGH in its physiological
concentration in order to investigate the possibility of protein
quantification has been achieved.
Abstract: The main aim of this research is to investigate a novel technique for implementing a more natural and intelligent conversation system. Conversation systems are designed to converse like a human as much as their intelligent allows. Sometimes, we can think that they are the embodiment of Turing-s vision. It usually to return a predetermined answer in a predetermined order, but conversations abound with uncertainties of various kinds. This research will focus on an integrated natural language processing approach. This approach includes an integrated knowledge-base construction module, a conversation understanding and generator module, and a state manager module. We discuss effectiveness of this approach based on an experiment.
Abstract: An advanced composite flywheel rotor consisting of
intra and inter hybrid rims was designed to optimally increase the energy capacity, and was manufactured using filament winding with
in-situ curing. The flywheel has recently attracted considerable attention from many investigators since it possesses great potential in
many energy storage applications, including electric utilities, hybrid or
electric automobiles, and space vehicles. In this investigation, a comprehensive study was conducted with the intent to implement
composites in high performance flywheel applications.The inner two
intra-hybrid rims (rims 1 and 2) were manufactured as a whole part
through continuous filament winding under in-situ curing conditions,
and so were the outer two rims (rims 3 and 4). The outer surface of rim
2 and the inner surface of rim 3 were CNC-tapered for press-fitting. Machined rims were finally press-fitted using a hydraulic press with a
maximum compressive force of approximately 1000 ton.
Abstract: The turbulent mixing of coolant streams of different
temperature and density can cause severe temperature fluctuations in
piping systems in nuclear reactors. In certain periodic contraction
cycles these conditions lead to thermal fatigue. The resulting aging
effect prompts investigation in how the mixing of flows over a sharp
temperature/density interface evolves. To study the fundamental
turbulent mixing phenomena in the presence of density gradients,
isokinetic (shear-free) mixing experiments are performed in a square
channel with Reynolds numbers ranging from 2-500 to 60-000.
Sucrose is used to create the density difference. A Wire Mesh Sensor
(WMS) is used to determine the concentration map of the flow in the
cross section. The mean interface width as a function of velocity,
density difference and distance from the mixing point are analyzed
based on traditional methods chosen for the purposes of
atmospheric/oceanic stratification analyses. A definition of the
mixing layer thickness more appropriate to thermal fatigue and based
on mixedness is devised. This definition shows that the thermal
fatigue risk assessed using simple mixing layer growth can be
misleading and why an approach that separates the effects of large
scale (turbulent) and small scale (molecular) mixing is necessary.
Abstract: This paper presents the results of the preliminary investigation of microwave (MW) irradiation pretreatments on the anaerobic digestion of food residues using biochemical methane potential (BMP) assays. Low solids systems with a total solids (TS) content ranging from 5.0-10.0% were analyzed. The inoculum to bulk mass of substrates to water ratio was 1:2:2 (mass basis). The experimental conditions for pretreatments were as follows: a control (no MW irradiation), two runs with MW irradiation for 15 and 30 minutes at 320 W, and another two runs with MW irradiation at 528 W for 30 and 60 minutes. The cumulative biogas production were 6.3 L and 8.7 L for 15min/320 W and 30min/320 W MW irradiation conditions, respectively, and 10.5 L and 11.4 L biogas for 30min/528 W and 60min/528 W, respectively, as compared to the control giving 5.8 L biogas. Both an increase in exposure time of irradiation and power of MW had increased the rate and yield of biogas. Singlefactor ANOVA tests (p
Abstract: Numerical simulations are performed for laminar
continuous and pulsed jets impinging on a surface in order to
investigate the effects of pulsing frequency on the heat transfer
characteristics. The time-averaged Nusselt number of pulsed jets is
larger in the impinging jet region as compared to the continuous jet,
while it is smaller in the outer wall jet region. At the stagnation point,
the mean and RMS Nusselt numbers become larger and smaller,
respectively, as the pulsing frequency increases. Unsteady behaviors
of vortical fluid motions and temperature field are also investigated to
understand the underlying mechanisms of heat transfer enhancement.
Abstract: This paper presents the impact study of GTO Controlled Series Capacitor (GCSC) parameters on measured impedance (Zseen) by MHO distance relays for single transmission line high voltage 220 kV in the presence of single phase to earth fault with fault resistance (RF). The study deals with a 220 kV single electrical transmission line of Eastern Algerian transmission networks at Group Sonelgaz (Algerian Company of Electrical and Gas) compensated by series Flexible AC Transmission System (FACTS) i.e. GCSC connected at midpoint of the transmission line. The transmitted active and reactive powers are controlled by three GCSC-s. The effects of maximum reactive power injected as well as injected maximum voltage by GCSC on distance relays measured impedance is treated. The simulations results investigate the effects of GCSC injected parameters: variable reactance (XGCSC), variable voltage (VGCSC) and reactive power injected (QGCSC) on measured resistance and reactance in the presence of earth fault with resistance fault varied between 5 to 50 Ω for three cases study.
Abstract: Today with the rapid growth of telecommunications equipment, electronic and developing more and more networks of power, influence of electromagnetic waves on one another has become hot topic discussions. So in this article, this issue and appropriate mechanisms for EMC operations have been presented. First, impact of high voltage lines on the surrounding environment especially on the control room has been investigated, then to reduce electromagnetic radiation, various methods of shielding are provided and shielding effectiveness of them has been compared. It should be expressed that simulations have been done by the finite element method (FEM).
Abstract: The Kinetics formation of labile Complex
Ag (I) tetra (p-carboxyphenyl) porphyrin, was investigated at 25oC
and I=0.1M (NaNO3). By spectrophotometric titration, the
composition ratio of the complex was established to be 2:1
(Ag : H2TCPP). The equilibrium constant, K, was found to be
log 10-6.53. Binding of the first Ag (I) was found to be rate
determining step with rate constant, k1= 4.67×102 . A plausible
mechanism is discussed. We discus theoretically why Ag(I)2TCPP is
unstable.
Abstract: Synthesis gas manufacturing by steam reforming of hydrocarbons is an important industrial process. High endothermic nature of the process makes it one of the most cost and heat intensive processes. In the present work, composite effect of different inert gases on synthesis gas yield, feed gas conversion and temperature distribution along the reactor length has been studied using a heterogeneous model. Mathematical model was developed as a first stage and validated against the existing process models. With the addition of inert gases, a higher yield of synthesis gas is observed. Simultaneously the rector outlet temperature drops to as low as 810 K. It was found that Xenon gives the highest yield and conversion while Helium gives the lowest temperature. Using Xenon inert gas 20 percent reduction in outlet temperature was observed compared to traditional case.
Abstract: Fly ash is a significant waste that is released of
thermal power plants and defined as very fine particles that are drifted upward with up taken by the flue gases due to the burning of
used coal [1]. The fly-ash is capable of removing organic
contaminants in consequence of high carbon content, a large surface area per unit volume and contained heavy metals. Therefore, fly ash
is used as an effective coagulant and adsorbent by pelletization [2, 3].
In this study, the possibility of use of fly ash taken from Turkey like low-cost adsorbent for adsorption of zinc ions found in waste
water was investigated. The fly ash taken from Turkey was pelletized with bentonite and molass to evaluate the adsorption capaticity. For
this purpose; analyses such as sieve analysis, XRD, XRF, FTIR and SEM were performed. As a result, it was seen that pellets prepared
from fly ash, bentonite and molass would be used for zinc adsorption.
Abstract: The bit error rate (BER) performance for ultra-wide
band (UWB) indoor communication with impact of metallic furniture
is investigated. The impulse responses of different indoor
environments for any transmitter and receiver location are computed
by shooting and bouncing ray/image and inverse Fourier transform
techniques. By using the impulse responses of these multipath
channels, the BER performance for binary pulse amplitude
modulation (BPAM) impulse radio UWB communication system are
calculated. Numerical results have shown that the multi-path effect
by the metallic cabinets is an important factor for BER performance.
Also the outage probability for the UWB multipath environment with
metallic cabinets is more serious (about 18%) than with wooden
cabinets. Finally, it is worth noting that in these cases the present
work provides not only comparative information but also quantitative
information on the performance reduction.
Abstract: This study investigates the relationship between 10
year bond value, Yen/U.S dollar exchange rate, non-farm payrolls (all
employs) and crude oil to U.S. Dow Jones Sustainability Index. A
GARCH model is used to test these relationships for the period
January 1st 1999 to January 31st 2008 using monthly data. Results
show that an increase of the 10 year bond and non farm payrolls (all
employs) lead to an increase of the D.J.S.I returns. On the contrary
the volatility of the Yen/U.S dollar exchange rates as well as the
increase of crude oil returns has negative effects on the U.S D.J.S.I
returns. This study aims at assisting investors to understand the
influences certain macroeconomic indicators have on the companies-
stock returns as reported by the D.J.S.I.
Abstract: Mycophenolic acid “MPA" is a secondary metabolite
of Penicillium bervicompactum with antibiotic and
immunosuppressive properties. In this study, fermentation process
was established for production of mycophenolic acid by Penicillium
bervicompactum MUCL 19011 in shake flask. The maximum MPA
production, product yield and productivity were 1.379 g/L, 18.6 mg/g
glucose and 4.9 mg/L.h respectively. Glucose consumption, biomass
and MPA production profiles were investigated during fermentation
time. It was found that MPA production starts approximately after
180 hours and reaches to a maximum at 280 h. In the next step, the
effects of methionine and acetate concentrations on MPA production
were evaluated. Maximum MPA production, product yield and
productivity (1.763 g/L, 23.8 mg/g glucose and 6.30 mg/L. h
respectively) were obtained with using 2.5 g/L methionine in culture
medium. Further addition of methionine had not more positive effect
on MPA production. Finally, results showed that the addition of
acetate to the culture medium had not any observable effect on MPA
production
Abstract: Given the motivation of maps impact in enhancing the
perception of the quality of life in a region, this work examines the
use of spatial analytical techniques in exploring the role of space in
shaping human development patterns in Assiut governorate.
Variations of human development index (HDI) of the governorate-s
villages, districts and cities are mapped using geographic information
systems (GIS). Global and local spatial autocorrelation measures are
employed to assess the levels of spatial dependency in the data and to
map clusters of human development. Results show prominent
disparities in HDI between regions of Assiut. Strong patterns of
spatial association were found proving the presence of clusters on the
distribution of HDI. Finally, the study indicates several "hot-spots" in
the governorate to be area of more investigations to explore the
attributes of such levels of human development. This is very
important for accomplishing the development plan of poorest regions
currently adopted in Egypt.