Abstract: In literatures, many researches proposed various
methods to reduce PAPR (Peak to Average Power Ratio). Among
those, DSI (Dummy Sequence Insertion) is one of the most attractive
methods for WiMAX systems because it does not require side
information transmitted along with user data. However, the
conventional DSI methods find dummy sequence by performing an
iterative procedure until achieving PAPR under a desired threshold.
This causes a significant delay on finding dummy sequence and also
effects to the overall performances in WiMAX systems. In this paper,
the new method based on DSI is proposed by finding dummy
sequence without the need of iterative procedure. The fast DSI
method can reduce PAPR without either delays or required side
information. The simulation results confirm that the proposed method
is able to carry out PAPR performances as similar to the other
methods without any delays. In addition, the simulations of WiMAX
system with adaptive modulations are also investigated to realize the
use of proposed methods on various fading schemes. The results
suggest the WiMAX designers to modify a new Signal to Noise Ratio
(SNR) criteria for adaptation.
Abstract: In this paper we study a food chain model with three trophic levels and Michaelis-Menten type ratio-dependent functional response. Distinctive feature of this model is the sensitive dependence of the dynamical behavior on the initial populations and parameters of the real world. The stability of the equilibrium points are also investigated.
Abstract: Martensitic stainless steels have been extensively used for their good corrosion resistance and better mechanical properties. Heat treatment was suggested as one of the most excellent ways to this regard; hence, it affects the microstructure, mechanical and corrosion properties of the steel. In the current research work the microstructural changes and corrosion behavior in an AISI 420A stainless steel exposed to temperatures in the 980-1035oC range were investigated. The heat treatment is carried out in vacuum furnace within the said temperature range. The quenching of the samples was carried out in oil, brine and water media. The formation and stability of passive film was studied by Open Circuit Potential, Potentiodynamic polarization and Electrochemical Scratch Tests. The Electrochemical Impedance Spectroscopy results simulated with Equivalent Electrical Circuit suggested bilayer structure of outer porous and inner barrier oxide films. The quantitative data showed thick inner barrier oxide film retarded electrochemical reactions. Micrographs of the quenched samples showed sigma and chromium carbide phases which prove the corrosion resistance of steel alloy.
Abstract: Effective cooling of electronic equipment has emerged
as a challenging and constraining problem of the new century. In the
present work the feasibility and effectiveness of jet impingement
cooling on electronics were investigated numerically and
experimentally. Studies have been conducted to see the effect of the
geometrical parameters such as jet diameter (D), jet to target
spacing (Z) and ratio of jet spacing to jet diameter (Z/D) on the heat
transfer characteristics. The values of Reynolds numbers considered
are in the range 7000 to 42000. The results obtained from the
numerical studies are validated by conducting experiments. From the
studies it is found that the optimum value of Z/D ratio is 5. For a
given Reynolds number, the Nusselt number increases by about 28%
if the diameter of the nozzle is increased from 1mm to 2mm.
Correlations are proposed for Nusselt number in terms of Reynolds
number and these are valid for air as the cooling medium.
Abstract: The aims of this paper are to study the efficacy of
chitosan nanoparticles in stimulating specific antibody against
A/H1N1 influenza antigen in mice. Chitosan nanoparticles (CSN)
were characterized by TEM. The results showed that the average size
of CSN was from 80nm to 106nm. The efficacy of A/H1N1 influenza
vaccine loaded on the surface of CSN showed that loading efficiency
of A/H1N1 influenza antigen on CSN was from 93.75 to 100%. Safe
property of the vaccine were tested. In 10 days post vaccination,
group of CSN 30 kDa and 300 kDa loaded A/H1N1 influenza antigen
were the rate of immune response on mice to be 100% (9/9) higher
than Al(OH)3 and other adjuvant. 100% mice in the experiment of all
groups had immune response in 20 days post vaccination. The results
also showed that HI titer of the group using CSN 300 kDa as an
adjuvant increased significantly up to 3971 HIU, over three-fold
higher than the Al(OH)3 adjuvant, chitosan (CS), and one hundredfold
than the A/H1N1 antigen only. Stability of the vaccine
formulation was investigated.
Abstract: This research aims at modeling and simulating the effects of nanofluids on cylindrical heat pipes thermal performance using the ANSYS-FLUENT CFD commercial software. The heat pipe outer wall temperature distribution, thermal resistance, liquid pressure and axial velocity in presence of suspended nano-scaled solid particle (i.e. Cu, Al2O3 and TiO2) within the fluid (water) were investigated. The effect of particle concentration and size were explored and it is concluded that the thermal performance of the heat pipe is improved when using nanofluid as the system working fluid. Additionally, it was observed that the thermal resistance of the heat pipe drops as the particle concentration level increases and particle radius decreases.
Abstract: This research investigates the factors that influence moral judgments when dealing with ethical dilemmas in the organizational context. It also investigates the antecedents of individual ethical ideology (idealism and relativism). A mixed method study, which combines qualitative (field study) and quantitative (survey) approaches, was used in this study. An initial model was developed first, which was then fine-tuned based on field studies. Data were collected from managers in Malaysian large organizations. The results of this study reveal that in-group collectivism culture, power distance culture, parental values, and religiosity were significant as antecedents of ethical ideology. However, direct effects of these variables on moral judgment were not significant. Furthermore, the results of this study confirm the significant effects of ethical ideology on moral judgment. This study provides valuable insight into evaluating the validity of existing theory as proposed in the literature and offers significant practical implications.
Abstract: In this study a two dimensional axisymmetric, steady state and incompressible laminar flow in a rotating single disk is numerically investigated. The finite volume method is used for solving the momentum equations. The numerical model and results
are validated by comparing it to previously reported experimental data for velocities, angles and moment coefficients. It is
demonstrated that increasing the axial distance increases the value of axial velocity and vice versa for tangential and total velocities. However, the maximum value of nondimensional radial velocity
occurs near the disk wall. It is also found that with increase rotational Reynolds number, moment coefficient decreases.
Abstract: The importance of nurturing, accumulating, and efficiently deploying knowledge resources through formal structures and organisational mechanisms is well understood. Recent trends in knowledge management (KM) highlight that the effective creation and transfer of knowledge can also rely upon extra-organisational channels, such as, informal networks. The perception exists that the role of informal networks in knowledge creation and performance has been underestimated in the organisational context. Literature indicates that many managers fail to comprehend and successfully exploit the potential role of informal networks to create value for their organisations. This paper investigates: 1) whether managers share work-specific knowledge with informal contacts within and outside organisational boundaries; and 2) what do they think is the importance of this knowledge collaboration in their learning and work outcomes.
Abstract: PCMs have always been viewed as a suitable
candidate for off peak thermal storage, particularly for refrigeration
systems, due to the high latent energy densities of these materials.
However, due to the need to have them encapsulated within a
container this density is reduced. Furthermore, PCMs have a low
thermal conductivity which reduces the useful amount of energy
which can be stored. To consider these factors, the true energy
storage density of a PCM system was proposed and optimised for
PCMs encapsulated in slabs. Using a validated numerical model of
the system, a parametric study was undertaken to investigate the
impact of the slab thickness, gap between slabs and the mass flow
rate. The study showed that, when optimised, a PCM system can
deliver a true energy storage density between 53% and 83% of the
latent energy density of the PCM.
Abstract: Coal fly ash (CFA) generated by coal-based thermal
power plants is mainly composed of quartz, mullite, and unburned
carbon. In this study, the effect of unburned carbon on CFA toward
its adsorption capacity was investigated. CFA with various carbon
content was obtained by refluxing it with sulfuric acid having various
concentration at various temperature and reflux time, by heating at
400-800°C, and by sieving into 100-mesh in particle size. To
evaluate the effect of unburned carbon on CFA toward its adsorption
capacity, adsorption of methyl violet solution with treated CFA was
carried out. The research shows that unburned carbon leads to
adsorption capacity decrease. The highest adsorption capacity of
treated CFA was found 5.73 x 10-4mol.g-1.
Abstract: A numerical analysis of wave and hydrodynamic models
is used to investigate the influence of WAve and Storm Surge
(WASS) in the regional and coastal zones. The numerical analyzed
system consists of the WAve Model Cycle 4 (WAMC4) and the
Princeton Ocean Model (POM) which used to solve the energy
balance and primitive equations respectively. The results of both
models presented the incorporated surface wave in the regional
zone affected the coastal storm surge zone. Specifically, the results
indicated that the WASS generally under the approximation is not
only the peak surge but also the coastal water level drop which
can also cause substantial impact on the coastal environment. The
wave–induced surface stress affected the storm surge can significantly
improve storm surge prediction. Finally, the calibration of wave
module according to the minimum error of the significant wave height
(Hs) is not necessarily result in the optimum wave module in the
WASS analyzed system for the WASS prediction.
Abstract: A double module hollow fiber supported liquid
membrane (HFSLM) was applied to selectively separate lead and
mercury ions from dilute synthetic produced water. The experiments
were investigated on several variables: types of extractants
(D2EHPA, Cyanex 471, Aliquat 336, and TOA), concentration of the
selected extractant and operating time. The results clearly showed
that the double module HFSLM could selectively separate Pb(II) and
Hg(II) in feed solution at a very low concentration to less than the
regulatory discharge limit of 0.2 and 0.005 mg/L issued by the
Ministry of Industry and the Ministry of Natural Resource
Environment, Thailand. The highest extractions of lead and mercury
ions from synthetic produced water were 96% and 100% using 0.03
M D2EHPA and 0.06 M Aliquat 336 as the extractant for the first
and second modules.
Abstract: Coated tool inserts can be considered as the backbone
of machining processes due to their wear and heat resistance.
However, defects of coating can degrade the integrity of these inserts
and the number of these defects should be minimized or eliminated if
possible. Recently, the advancement of coating processes and
analytical tools open a new era for optimizing the coating tools.
First, an overview is given regarding coating technology for cutting
tool inserts. Testing techniques for coating layers properties, as well
as the various coating defects and their assessment are also surveyed.
Second, it is introduced an experimental approach to examine the
possible coating defects and flaws of worn multicoated carbide
inserts using two important techniques namely scanning electron
microscopy and atomic force microscopy. Finally, it is
recommended a simple procedure for investigating manufacturing
defects and flaws of worn inserts.
Abstract: This paper investigates the issue of building decision
trees from data with imprecise class values where imprecision is
encoded in the form of possibility distributions. The Information
Affinity similarity measure is introduced into the well-known gain
ratio criterion in order to assess the homogeneity of a set of
possibility distributions representing instances-s classes belonging to
a given training partition. For the experimental study, we proposed an
information affinity based performance criterion which we have used
in order to show the performance of the approach on well-known
benchmarks.
Abstract: Training neural networks to capture an intrinsic
property of a large volume of high dimensional data is a difficult
task, as the training process is computationally expensive. Input
attributes should be carefully selected to keep the dimensionality of
input vectors relatively small.
Technical indexes commonly used for stock market prediction
using neural networks are investigated to determine its effectiveness
as inputs. The feed forward neural network of Levenberg-Marquardt
algorithm is applied to perform one step ahead forecasting of
NASDAQ and Dow stock prices.
Abstract: Society has grown to rely on Internet services, and the
number of Internet users increases every day. As more and more
users become connected to the network, the window of opportunity
for malicious users to do their damage becomes very great and
lucrative. The objective of this paper is to incorporate different
techniques into classier system to detect and classify intrusion from
normal network packet. Among several techniques, Steady State
Genetic-based Machine Leaning Algorithm (SSGBML) will be used
to detect intrusions. Where Steady State Genetic Algorithm (SSGA),
Simple Genetic Algorithm (SGA), Modified Genetic Algorithm and
Zeroth Level Classifier system are investigated in this research.
SSGA is used as a discovery mechanism instead of SGA. SGA
replaces all old rules with new produced rule preventing old good
rules from participating in the next rule generation. Zeroth Level
Classifier System is used to play the role of detector by matching
incoming environment message with classifiers to determine whether
the current message is normal or intrusion and receiving feedback
from environment. Finally, in order to attain the best results,
Modified SSGA will enhance our discovery engine by using Fuzzy
Logic to optimize crossover and mutation probability. The
experiments and evaluations of the proposed method were performed
with the KDD 99 intrusion detection dataset.
Abstract: This study was conducted to investigate the incidence
of pathogenic bacteria: Salmonella, Shigella, Escherichia coli O157
and Staphylococcus aureus in cakes and tarts collected from thirtyfive
confectionery producing and selling premises located within
Tripoli city, Libya. The results revealed an incidence of S. aureus
with 94.4 and 48.0 %, E. coli O157 with 14.7 and 4.0 % and Salmonella
sp. with 5.9 and 8.0 % in cakes and tarts samples respectively;
while Shigella was not detected in all samples. In order to determine
the source of these pathogenic bacteria, cotton swabs were taken
from the hands of workers on the production line, the surfaces of
preparation tables and cream whipping instruments. The results
showed that the cotton swabs obtained from the hands of workers
contained S. aureus and Salmonella sp. with an incidence of 42.9 and
2.9 %, the cotton swabs obtained from the surfaces of preparation
tables 22.9 and 2.9 % and the cotton swabs obtained from the cream
whipping instruments 14.3 and 0.0 % respectively; while E. coli
O157 and Shigella sp. were not detected in all swabs. Additionally,
other bacteria were isolated from the hands of workers and the Surfaces
of producing equipments included: Aeromonas sp., Pseudomonas
sp., E. coli, Klebsiella sp., Enterobacter sp., Citrobacter sp.,
Proteus sp., Serratia sp. and Acinetobacter sp. These results indicate
that some of the cakes and tarts might pose threat to consumer's
health. Meanwhile, occurrences of pathogenic bacteria on the hands
of those who are working in production line and the surfaces of
equipments reflect poor hygienic practices at most confectionery
premises examined in this study. Thus, firm and continuous surveillance
of these premises is needed to insure the consumer's health and
safety.
Abstract: Underpricing is one anomaly in initial public offerings
(IPO) literature that has been widely observed across different stock
markets with different trends emerging over different time periods.
This study seeks to determine how IPOs on the JSE performed on the
first day, first week and first month over the period of 1996-2011.
Underpricing trends are documented for both hot and cold market
periods in terms of four main sectors (cyclical, defensive, growth
stock and interest rate sensitive stocks). Using a sample of 360 listed
companies on the JSE, the empirical findings established that IPOs
on the JSE are significantly underpriced with an average market
adjusted first day return of 62.9%. It is also established that hot
market IPOs on the JSE are more underpriced than the cold market
IPOs. Also observed is the fact that as the offer price per share
increases above the median price for any given period, the level of
underpricing decreases substantially. While significant differences
exist in the level of underpricing of IPOs in the four different sectors
in the hot and cold market periods, interest rates sensitive stocks
showed a different trend from the other sectors and thus require
further investigation to uncover this pattern.
Abstract: The objective of this work is to investigate the
turbulent reacting flow in a three dimensional combustor with
emphasis on the effect of inlet swirl flow through a numerical
simulation. Flow field is analyzed using the SIMPLE method which is
known as stable as well as accurate in the combustion modeling, and
the finite volume method is adopted in solving the radiative transfer
equation. In this work, the thermal and flow characteristics in a three
dimensional combustor by changing parameters such as equivalence
ratio and inlet swirl angle have investigated. As the equivalence ratio
increases, which means that more fuel is supplied due to a larger inlet
fuel velocity, the flame temperature increases and the location of
maximum temperature has moved towards downstream. In the mean
while, the existence of inlet swirl velocity makes the fuel and
combustion air more completely mixed and burnt in short distance.
Therefore, the locations of the maximum reaction rate and temperature
were shifted to forward direction compared with the case of no swirl.