Abstract: This paper investigates experimentally and
analytically the torsion behavior of steel fibered high strength self
compacting concrete beams reinforced by GFRP bars. Steel fibered
high strength self compacting concrete (SFHSSCC) and GFRP bars
became in the recent decades a very important materials in the
structural engineering field. The use of GFRP bars to replace steel
bars has emerged as one of the many techniques put forward to
enhance the corrosion resistance of reinforced concrete structures.
High strength concrete and GFRP bars attract designers and
architects as it allows improving the durability as well as the esthetics
of a construction. One of the trends in SFHSSCC structures is to
provide their ductile behavior and additional goal is to limit
development and propagation of macro-cracks in the body of
SFHSSCC elements. SFHSSCC and GFRP bars are tough, improve
the workability, enhance the corrosion resistance of reinforced
concrete structures, and demonstrate high residual strengths after
appearance of the first crack. Experimental studies were carried out
to select effective fiber contents. Three types of volume fraction from
hooked shape steel fibers are used in this study, the hooked steel
fibers were evaluated in volume fractions ranging between 0.0%,
0.75% and 1.5%. The beams shape is chosen to create the required
forces (i.e. torsion and bending moments simultaneously) on the test
zone. A total of seven beams were tested, classified into three groups.
All beams, have 200cm length, cross section of 10×20cm,
longitudinal bottom reinforcement of 3
Abstract: The result of process of territory-s development is the territory-s state of development (TSoD), which is pointed towards the provision and improvement of people-s life conditions. The authors offer to measure the TSoD according to their own developed model. Using the available statistical data regarding the values of model-s elements, the authors empirically show which element mainly determines the TSoD. The findings of the research showed that the key elements of the TSoD are the “Material welfare of people" and “People-s health". Performing a deeper statistical analysis of correlation between these elements, it turned out that it is not so necessary for a country to be bent on trying to increase the material growth of a territory, because a relatively high index of life expectancy at birth could be ensured also by much more modest material resources. On the other hand, the economical feedback of longer lifespan within countries with lower material performance is also relatively low.
Abstract: Contemporary science and technologies largely widen
the gap between the spiritual and rational of the society. Industrial
and technological breakthroughs might radically affect most
processes in the society, thus losing the cultural heritage. The
thinkers recognized the dangers of the decadence in the first place. In
the present article the ways of preserving cultural heritage have been
investigated. Memory has always been a necessary condition for selfidentification,
- continuity is based on this. The authors have
supported the hypothesis that continuity and ethnic memory are the
very mechanisms that preserve cultural heritage. Such problemformulating
will facilitate another, new look at the material, spiritual
and arts spheres of the cultural heritage of numerous ethnic groups.
The fundamental works by major European and Kazakh scientists
have been taken as a basis for the research done.
Abstract: The research focuses on the effects of polyphenols
extracted from Sambucus nigra fruit, using an experimental arterial
hypertension pattern, as well as their influence on the oxidative
stress. The results reveal the normalization of the reduced glutathion
concentration, as well as a considerable reduction in the
malondialdehide serum concentration by the polyphenolic protection.
The rat blood pressure values were recorded using a CODATM
system, which uses a non-invasive blood pressure measuring method.
All the measured blood pressure components revealed a biostatistically
significant (p
Abstract: We examine the maximum theorem by Berge from the
point of view of Bishop style constructive mathematics. We will show
an approximate version of the maximum theorem and the maximum
theorem for functions with sequentially locally at most one maximum.
Abstract: This paper details few mechanical modeling and
design issues of RF MEMS switches. We concentrate on an
electrostatically actuated broad side series switch; surface
micromachined with a crab leg membrane. The same results are
extended to any complex structure. With available experimental data
and fabrication results, we present the variation in dynamic
performance and compliance of the switch with reference to few
design issues, which we find are critical in deciding the dynamic
behavior of the switch, without compromise on the RF
characteristics. The optimization of pull in voltage, transient time and
resonant frequency with regard to these critical design parameters are
also presented.
Abstract: A number of mass spectrometry applications are already available as web-based and windows-based systems to calculate isotope pattern and to display the mass spectrum based on the specific molecular formula besides providing necessary information. These applications were evaluated and compared with our new alternative application called Theoretical Isotope Generator (TIG) in terms of its functionality and features provided to prove this new application is working better and performing well. TIG provides extra features than others, complete with several functionality such as drawing, normalizing and zooming the generated graph that convey with the molecular information in a number of formats by providing the details of the calculation and molecules. Thus, any chemist, students, lecturers and researchers from anywhere could use TIG to gain related information on molecules and their relative intensity.
Abstract: In this study, the two dimensional heat conduction
problem for the dry friction clutch disc is modeled mathematically
analysis and is solved numerically using finite element method, to
determine the temperature field when band contacts occurs between
the rubbing surfaces during the operation of an automotive clutch.
Temperature calculation have been made for contact area of different
band width and the results obtained compared with these attained
when complete contact occurs. Furthermore, the effects of slipping
time and sliding velocity function are investigated as well. Both
single and repeated engagements made at regular interval are
considered.
Abstract: The basis of this paper is the assumption, that graviton
is a measurable entity of molecular gravitational acceleration and this
is not a hypothetical entity. The adoption of this assumption as an
axiom is tantamount to fully opening the previously locked door to
the boundary theory between laminar and turbulent flows. It leads to
the theorem, that the division of flows of Newtonian (viscous) fluids
into laminar and turbulent is true only, if the fluid is influenced by a
powerful, external force field. The mathematical interpretation of this
theorem, presented in this paper shows, that the boundary between
laminar and turbulent flow can be determined theoretically. This is a
novelty, because thus far the said boundary was determined
empirically only and the reasons for its existence were unknown.
Abstract: This paper focuses on the calibration problem of a
multi-view shooting system designed for the production of 3D
content for auto-stereoscopic visualization. The considered multiview
camera is characterized by coplanar and decentered image
sensors regarding to the corresponding optical axis. Based on the
Faugéras and Toscani-s calibration approach, a calibration method is
herein proposed for the case of multi-view camera with parallel and
decentered image sensors. At first, the geometrical model of the
shooting system is recalled and some industrial prototypes with some
shooting simulations are presented. Next, the development of the
proposed calibration method is detailed. Finally, some simulation
results are presented before ending with some conclusions about this
work.
Abstract: MOC (method of cell) is a new method of investigating
wave propagating in material with periodic microstructure, and can
reflect the effect of microstructure. Wave propagation in periodically
laminated medium consisting of linearly elastic layers can be treated
as a special application of this method. In this paper, it was used to
simulate the dynamic response of carbon-phenolic to impulsive
loading under certain boundary conditions. From the comparison
between the results obtained from this method and the exact results
based on propagator matrix theory, excellent agreement is achieved.
Conclusion can be made that the oscillation periodicity is decided by
the thickness of sub-cells. In the end, the NHDMOC method, which
permits studying stress wave propagation with one dimensional strain,
was applied to study the one-dimensional stress wave propagation. In
this paper, the ZWT nonlinear visco-elastic constitutive relationship
with 7 parameters, NHDMOC, and corresponding equations were
deduced. The equations were verified, comparing the elastic stress
wave propagation in SHPB with, respectively, the elastic and the
visco-elastic bar. Finally the dispersion and attenuation of stress wave
in SHPB with visco-elastic bar was studied.
Abstract: Snow cover is an important phenomenon in
hydrology, hence modeling the snow accumulation and melting is an
important issue in places where snowmelt significantly contributes to
runoff and has significant effect on water balance. The physics-based
models are invariably distributed, with the basin disaggregated into
zones or grid cells. Satellites images provide valuable data to verify
the accuracy of spatially distributed model outputs. In this study a
spatially distributed physically based model (WetSpa) was applied to
predict snow cover and melting in the Latyan dam watershed in Iran.
Snowmelt is simulated based on an energy balance approach. The
model is applied and calibrated with one year of observed daily
precipitation, air temperature, windspeed, and daily potential
evaporation. The predicted snow-covered area is compared with
remotely sensed images (MODIS). The results show that simulated
snow cover area SCA has a good agreement with satellite image
snow cover area SCA from MODIS images. The model performance
is also tested by statistical and graphical comparison of simulated and
measured discharges entering the Latyan dam reservoir.
Abstract: We developed a method based on quasi-molecular
modelling to simulate the fall of water drops on horizontally smooth
and rough surfaces. Each quasi-molecule was a group of particles
that interacted in a fashion entirely analogous to classical Newtonian
molecular interactions. When a falling water droplet was simulated at
low impact velocity on both smooth and rough surfaces, the droplets
moved periodically (i.e. the droplets moved up and down for a
certain period, finally they stopped moving and reached a steady
state), spreading and recoiling without splash or break-up. Spreading
rates of falling water droplets increased rapidly as time increased
until the spreading rate reached its steady state at time t ~ 0.25 s for
rough surface and t ~ 0.40 s for smooth surface. The droplet height
above both surfaces decreased as time increased, remained constant
after the droplet diameter attained a maximum value and reached its
steady state at time t ~ 0.4 s. However, rough surface had higher
spreading rates of falling water droplets and lower height on the
surface than smooth one.
Abstract: A self-association model has been used to understand
the concentration dependence of free energy of mixing (GM), heat of
mixing (HM), entropy of mixing (SM), activity (a) and microscopic
structures, such as concentration fluctuation in long wavelength limit
(Scc(0)) and Warren-Cowley short range order parameter ( 1
α )for Cu-
Tl molten alloys at 1573K. A comparative study of surface tension of
the alloys in the liquid state at that temperature has also been carried
out theoretically as function of composition in the light of Butler-s
model, Prasad-s model and quasi-chemical approach. Most of the
computed thermodynamic properties have been found in agreement
with the experimental values. The analysis reveals that the Cu-Tl
molten alloys at 1573K represent a segregating system at all
concentrations with moderate interaction. Surface tensions computed
from different approaches have been found to be comparable to each
other showing increment with the composition of copper.
Abstract: This paper is concerned with an improved algorithm
based on the piecewise-smooth Mumford and Shah (MS) functional
for an efficient and reliable segmentation. In order to speed up
convergence, an additional force, at each time step, is introduced
further to drive the evolution of the curves instead of only driven by
the extensions of the complementary functions u + and u - . In our
scheme, furthermore, the piecewise-constant MS functional is
integrated to generate the extra force based on a temporary image that
is dynamically created by computing the union of u + and u - during
segmenting. Therefore, some drawbacks of the original algorithm,
such as smaller objects generated by noise and local minimal problem
also are eliminated or improved. The resulting algorithm has been
implemented in Matlab and Visual Cµ, and demonstrated efficiently
by several cases.
Abstract: An experiment was performed with a 24.5 MeV 14N
beam on a 12C target in the cyclotron DC-60 located in Astana,
Kazakhstan, to study the elastic scattering of 14N on 12C; the
scattering was also analyzed at different energies for tracking the
phenomenon of remarkable structure at large angles. Its aims were to
extend the measurements to very large angles, and attempt to
uniquely identify the elastic scattering potential. Good agreement
between the theoretical and experimental data has been obtained with
suitable optical potential parameters. Optical model calculations with
l -dependent imaginary potentials were also applied to the data and
relatively good agreement was found.
Abstract: In this study, mechanically alloyed Al 2024 powder is
densified by conventional sintering and by equal channel angular
pressing (ECAP) with and without back pressure. The powder was
encapsulated in an aluminium can for consolidation through ECAP.
The properties obtained in the compacts by conventional sintering
route and by ECAP are compared. The effect of conventional
sintering and ECAP on consolidation behaviour of powder,
microstructure, density and hardness is discussed. Room temperature
back pressure aided ECAP results in nearly full denser (97% of its
theoretical density) compact at room temperature. NanoIndentation
technique was used to determine the modulus of the consolidated
compacts.
Abstract: Knowledge sharing enables the information or
knowledge to be transmitted from one source to another. This paper
demonstrates the needs of having the online book catalogue which
can be used to facilitate disseminating information on textbook used
in the university. This project is aimed to give access to the students
and lecturers to the list of books in the bookstore and at the same
time to allow book reviewing without having to visit the bookstore
physically. Research is carried out according to the boundaries which
accounts to current process of new book purchasing, current system
used by the bookstore and current process the lecturers go through
for reviewing textbooks. The questionnaire is used to gather the
requirements and it is distributed to 100 students and 40 lecturers.
This project has enabled the improvement of a manual process to be
carried out automatically, through a web based platform. It is shown
based on the user acceptance survey carried out that target groups
found that this web service is feasible to be implemented in
Universiti Teknologi PETRONAS (UTP), and they have shown
positive signs of interest in utilizing it in the future.
Abstract: This research were investigated, determined, and
analyzed of the climate characteristically change in the provincial
Udon Thani in the period of 60 surrounding years from 1951 to 2010
A.D. that it-s transferred to effects of climatologically data for
determining global warming. Statistically significant were not found
for the 60 years- data (R2
Abstract: A new generation of manufacturing machines
so-called MIMCA (modular and integrated machine control
architecture) capable of handling much increased complexity in
manufacturing control-systems is presented. Requirement for more
flexible and effective control systems for manufacturing machine
systems is investigated and dimensioned-which highlights a need for
improved means of coordinating and monitoring production
machinery and equipment used to- transport material. The MIMCA
supports simulation based on machine modeling, was conceived by
the authors to address the issues. Essentially MIMCA comprises an
organized unification of selected architectural frameworks and
modeling methods, which include: NISTRCS, UMC and Colored
Timed Petri nets (CTPN). The unification has been achieved; to
support the design and construction of hierarchical and distributed
machine control which realized the concurrent operation of reusable
and distributed machine control components; ability to handle
growing complexity; and support requirements for real- time control
systems. Thus MIMCA enables mapping between 'what a machine
should do' and 'how the machine does it' in a well-defined but
flexible way designed to facilitate reconfiguration of machine
systems.