Abstract: In this study, the effects of biogas fuels on the performance of an annular micro gas turbine (MGT) were assessed experimentally and numerically. In the experiments, the proposed MGT system was operated successfully under each test condition; minimum composition to the fuel with the biogas was roughly 50% CH4 with 50% CO2. The power output was around 170W at 85,000 RPM as 90% CH4 with 10% CO2 was used and 70W at 65,000 RPM as 70% CH4 with 30% CO2 was used. When a critical limit of 60% CH4 was reached, the power output was extremely low. Furthermore, the theoretical Brayton cycle efficiency and electric efficiency of the MGT were calculated as 23% and 10%, respectively. Following the experiments, the measured data helped us identify the parameters of dynamic model in numerical simulation. Additionally, a numerical analysis of re-designed combustion chamber showed that the performance of MGT could be improved by raising the temperature at turbine inlet. This study presents a novel distributed power supply system that can utilize renewable biogas. The completed micro biogas power supply system is small, low cost, easy to maintain and suited to household use.
Abstract: Partial combustion of biomass in the gasifier generates producer gas that can be used for heating purposes and as supplementary or sole fuel in internal combustion engines. In this study, the virgin biomass obtained from hingan shell is used as the feedstock for gasifier to generate producer gas. The gasifier-engine system is operated on diesel and on esters of vegetable oil of hingan in liquid fuel mode operation and then on liquid fuel and producer gas combination in dual fuel mode operation. The performance and emission characteristics of the CI engine is analyzed by running the engine in liquid fuel mode operation and in dual fuel mode operation at different load conditions with respect to maximum diesel savings in the dual fuel mode operation. It was observed that specific energy consumption in the dual fuel mode of operation is found to be in the higher side at all load conditions. The brake thermal efficiency of the engine using diesel or hingan oil methyl ester (HOME) is higher than that of dual fuel mode operation. A diesel replacement in the tune of 60% in dual fuel mode is possible with the use of hingan shell producer gas. The emissions parameters such CO, HC, NOx, CO2 and smoke are higher in the case of dual fuel mode of operation as compared to that of liquid fuel mode.
Abstract: Spent petroleum catalyst from Korean petrochemical
industry contains trace amount of metals such as Ni, V and Mo.
Therefore an attempt was made to recover those trace metal using
bioleaching process. Different leaching parameters such as Fe(II)
concentration, pulp density, pH, temperature and particle size of
spent catalyst particle were studied to evaluate their effects on the
leaching efficiency. All the three metal ions like Ni, V and Mo
followed dual kinetics, i.e., initial faster followed by slower rate. The
percentage of leaching efficiency of Ni and V were higher than Mo.
The leaching process followed a diffusion controlled model and the
product layer was observed to be impervious due to formation of
ammonium jarosite (NH4)Fe3(SO4)2(OH)6. In addition, the lower
leaching efficiency of Mo was observed due to a hydrophobic coating
of elemental sulfur over Mo matrix in the spent catalyst.
Abstract: The concentrations of aliphatic and polycyclic aromatic hydrocarbons (PAH) were determined in atmospheric aerosol samples collected at a rural site in Hungary (K-puszta, summer 2008), a boreal forest (Hyytiälä,
April 2007) and a polluted rural area in Italy (San Pietro Capofiume, Po Valley, April 2008). A clear distinction between “clean" and “polluted" periods was observed. Concentrations obtained for Hyytiälä are significantly lower than those for the other two sites. Source reconciliation was performed using diagnostic parameters, such as the carbon preference index and ratios between PAH. The presence of an unresolved complex mixture of hydrocarbons, especially for the Finnish and Italian samples, is indicative of petrogenic inputs. In K-puszta, the aliphatic hydrocarbons are dominated by leaf wax n-alkanes. The long range transport of anthropogenic pollution contributed to the Finnish aerosol. Industrial activities and vehicular emissions represent major sources in San Pietro Capofiume. PAH in K-puszta consist of both pyrogenic and petrogenic compounds.
Abstract: This paper describes the optimization of a complex
dairy farm simulation model using two quite different methods of
optimization, the Genetic algorithm (GA) and the Lipschitz
Branch-and-Bound (LBB) algorithm. These techniques have been
used to improve an agricultural system model developed by Dexcel
Limited, New Zealand, which describes a detailed representation of
pastoral dairying scenarios and contains an 8-dimensional parameter
space. The model incorporates the sub-models of pasture growth and
animal metabolism, which are themselves complex in many cases.
Each evaluation of the objective function, a composite 'Farm
Performance Index (FPI)', requires simulation of at least a one-year
period of farm operation with a daily time-step, and is therefore
computationally expensive. The problem of visualization of the
objective function (response surface) in high-dimensional spaces is
also considered in the context of the farm optimization problem.
Adaptations of the sammon mapping and parallel coordinates
visualization are described which help visualize some important
properties of the model-s output topography. From this study, it is
found that GA requires fewer function evaluations in optimization
than the LBB algorithm.
Abstract: To reduce the carbon dioxide emission into the
atmosphere, adsorption is believed to be one of the most attractive
methods for post-combustion treatment of flue gas. In this work,
activated carbon (AC) was modified by polyethylenimine (PEI) via
impregnation in order to enhance CO2 adsorption capacity. The
adsorbents were produced at 0.04, 0.16, 0.22, 0.25, and 0.28 wt%
PEI/AC. The adsorption was carried out at a temperature range from
30 °C to 75 °C and five different gas pressures up to 1 atm. TG-DTA,
FT-IR, UV-visible spectrometer, and BET were used to characterize
the adsorbents. Effects of PEI loading on the AC for the CO2
adsorption were investigated. Effectiveness of the adsorbents on the
CO2 adsorption including CO2 adsorption capacity and adsorption
temperature was also investigated. Adsorption capacities of CO2 were
enhanced with the increase in the amount of PEI from 0.04 to 0.22
wt% PEI before the capacities decreased onwards from0.25 wt% PEI
at 30 °C. The 0.22 wt% PEI/AC showed higher adsorption capacity
than the AC for adsorption at 50 °C to 75 °C.
Abstract: Urban non-point source (NPS) pollution for a
residential catchment in Miri, Sarawak was investigated for two storm events in 2011. Runoff from two storm events were sampled and tested for water quality parameters including TSS, BOD5, COD,
NH3-N, NO3-N, NO2-N, P and Pb. Concentration of the water quality
parameters was found to vary significantly between storms and the pollutant of concern was found to be NO3-N, TSS, COD and Pb. Results were compared to the Interim National Water Quality
Standards for Malaysia (INWQS),and the stormwater runoff from the
study can be classified as polluted, exceeding class III water quality,
especially in terms of TSS, COD, and NH3-N with maximum EMCs
of 158, 135, and 2.17 mg/L, respectively.
Abstract: A mathematical model of the respiratory system is
introduced in this study. Geometrical dimensions of the respiratory
system were used to compute the acoustic properties of the
respiratory system using the electro-acoustic analogy. The effect of
the geometrical proportions of the respiratory system is observed in
the paper.
Abstract: Macrobenthos distribution along the coastal waters of
Penang National Park was studid to estimate the effect of different
environmental parameters at three stations, during six sampling
months, from June 2010 to April 2011. The aim of this survey was to
investigate different environment stress over soft bottom polychaete
community along Teluk Ketapang and Pantai Acheh (Penang
National Park) over a year period. Variations in the polychaete
community were evaluated using univariate and multivariate
methods. A total of 604 individuals were examined which was
grouped into 23 families. Family Nereidae was the most abundant
(22.68%), followed by Spionidae (22.02%), Hesionidae (12.58%),
Nephtylidae (9.27%) and Orbiniidae (8.61%). It is noticeable that
good results can only be obtained on the basis of good taxonomic
resolution. The maximum Shannon-Wiener diversity (H'=2.16) was
recorded at distance 200m and 1200m (August 2010) in Teluk
Ketapang and lowest value of diversity was found at distance 1200m
(December 2010) in Teluk Ketapang.
Abstract: In this paper newly reported Cosh window function is
used in the design of prototype filter for M-channel Near Perfect
Reconstruction (NPR) Cosine Modulated Filter Bank (CMFB). Local
search optimization algorithm is used for minimization of distortion
parameters by optimizing the filter coefficients of prototype filter.
Design examples are presented and comparison has been made with
Kaiser window based filterbank design of recently reported work.
The result shows that the proposed design approach provides lower
distortion parameters and improved far-end suppression than the
Kaiser window based design of recent reported work.
Abstract: In this study, the designed dual stage membrane
bioreactor (MBR) system was conceptualized for the treatment of
cyanide and heavy metals in electroplating wastewater. The design
consisted of a primary treatment stage to reduce the impact of
fluctuations and the secondary treatment stage to remove the residual
cyanide and heavy metal contaminants in the wastewater under
alkaline pH conditions. The primary treatment stage contained
hydrolyzed Citrus sinensis (C. sinensis) pomace and the secondary
treatment stage contained active Aspergillus awamori (A. awamori)
biomass, supplemented solely with C. sinensis pomace extract from
the hydrolysis process. An average of 76.37%, 95.37%, 93.26 and
94.76% and 99.55%, 99.91%, 99.92% and 99.92% degradation
efficiency for total cyanide (T-CN), including the sorption of nickel
(Ni), zinc (Zn) and copper (Cu) were observed after the first and
second treatment stages, respectively. Furthermore, cyanide
conversion by-products degradation was 99.81% and 99.75 for both
formate (CHOO-) and ammonium (NH4
+) after the second treatment
stage. After the first, second and third regeneration cycles of the C.
sinensis pomace in the first treatment stage, Ni, Zn and Cu removal
achieved was 99.13%, 99.12% and 99.04% (first regeneration cycle),
98.94%, 98.92% and 98.41% (second regeneration cycle) and 98.46
%, 98.44% and 97.91% (third regeneration cycle), respectively.
There was relatively insignificant standard deviation detected in all
the measured parameters in the system which indicated
reproducibility of the remediation efficiency in this continuous
system.
Abstract: In this paper, we consider the problem for identifying the unknown source in the Poisson equation. A modified Tikhonov regularization method is presented to deal with illposedness of the problem and error estimates are obtained with an a priori strategy and an a posteriori choice rule to find the regularization parameter. Numerical examples show that the proposed method is effective and stable.
Abstract: Data from 1731 Gentile di Puglia lambs, sired by 65 rams over a 5-year period were analyzed by a mixed model to estimate the variance components for heritability. The considered growth traits were: birth weight (BW), weight at 30 days of age (W30) and average daily gain from birth to 30 days of age (DG). Year of birth, sex of lamb, type of birth (single or twin), dam age at lambing and farm were significant sources of variation for all the considered growth traits. The average lamb weights were 3.85±0.16 kg at birth, 9.57±0.91 kg at 30 days of age and the average daily gain was 191±14 g. Estimates of heritability were 0.33±0.05, 0.41±0.06 and 0.16±0.05 respectively for the same traits. These values suggest there is a good opportunity to improve Gentile di Puglia lambs by selecting animals for growth traits.
Abstract: This study adopted previous fault patterns, results of
detection analysis, historical records and data, and experts-
experiences to establish fuzzy principles and estimate the failure
probability index of components of a power transformer. Considering
that actual parameters and limiting conditions of parameters may
differ, this study used the standard data of IEC, IEEE, and CIGRE as
condition parameters. According to the characteristics of each
condition parameter, relative degradation was introduced to reflect the
degree of influence of the factors on the transformer condition. The
method of fuzzy mathematics was adopted to determine the
subordinate function of the transformer condition. The calculation
used the Matlab Fuzzy Tool Box to select the condition parameters of
coil winding, iron core, bushing, OLTC, insulating oil and other
auxiliary components and factors (e.g., load records, performance
history, and maintenance records) of the transformer to establish the
fuzzy principles. Examples were presented to support the rationality
and effectiveness of the evaluation method of power transformer
performance conditions, as based on fuzzy comprehensive evaluation.
Abstract: A new strain of Type A influenza virus can cause the
transmission of H1N1 virus. This virus can spread between the
people by coughing and sneezing. Because the people are always
movement, so this virus can be easily spread. In this study, we
construct the dynamical network model of H1N1 virus by separating
the human into five groups; susceptible, exposed, infectious,
quarantine and recovered groups. The movement of people between
houses (local level) is considered. The behaviors of solutions to our
dynamical model are shown for the different parameters.
Abstract: The effect of the rotational speed and axial torque on
the diagnostics of tapered rolling element bearing defects was
investigated. The accelerometer was mounted on the bearing housing
and connected to Sound and Vibration Analyzer (SVAN 958) and
was used to measure the accelerations from the bearing housing. The
data obtained from the bearing was processed to detect damage of the
bearing using statistical tools and the results were subsequently
analyzed to see if bearing damage had been captured. From this study
it can be seen that damage is more evident when the bearing is
loaded. Also, at the incipient stage of damage the crest factor and
kurtosis values are high but as time progresses the crest factors and
kurtosis values decrease whereas the peak and RMS values are low at
the incipient stage but increase with damage.
Abstract: Direct conversion of methane to methanol by partial oxidation in a thermal reactor has a poor yield of about 2% which is less than the expected economical yield of about 10%. Conventional thermal catalytic reactors have been proposed to be superseded by plasma reactors as a promising approach, due to strength of the electrical energy which can break C-H bonds of methane. Among the plasma techniques, non-thermal dielectric barrier discharge (DBD) plasma chemical process is one of the most future promising technologies in synthesizing methanol. The purpose of this paper is presenting a brief review of CH4 oxidation with O2 in DBD plasma reactors based on the recent investigations. For this reason, the effect of various parameters of reactor configuration, feed ratio, applied voltage, residence time (gas flow rate), type of applied catalyst, pressure and reactor wall temperature on methane conversion and methanol selectivity are discussed.
Abstract: A number of routing algorithms based on learning
automata technique have been proposed for communication
networks. How ever, there has been little work on the effects of
variation of graph scarcity on the performance of these algorithms. In
this paper, a comprehensive study is launched to investigate the
performance of LASPA, the first learning automata based solution to
the dynamic shortest path routing, across different graph structures
with varying scarcities. The sensitivity of three main performance
parameters of the algorithm, being average number of processed
nodes, scanned edges and average time per update, to variation in
graph scarcity is reported. Simulation results indicate that the LASPA
algorithm can adapt well to the scarcity variation in graph structure
and gives much better outputs than the existing dynamic and fixed
algorithms in terms of performance criteria.
Abstract: The problem of exponential stability and periodicity for a class of cellular neural networks (DCNNs) with time-varying delays is investigated. By dividing the network state variables into subgroups according to the characters of the neural networks, some sufficient conditions for exponential stability and periodicity are derived via the methods of variation parameters and inequality techniques. These conditions are represented by some blocks of the interconnection matrices. Compared with some previous methods, the method used in this paper does not resort to any Lyapunov function, and the results derived in this paper improve and generalize some earlier criteria established in the literature cited therein. Two examples are discussed to illustrate the main results.
Abstract: Whereas in the third generation nuclear reactors,
dimensions of core and also the kind of coolant and enrichment
percent of fuel have significantly changed than the second
generation, therefore in this article the aim is based on a
comparative investigation between two same power reactors of
second and third generations, that the neutronic parameters of both
reactors such as: K∞, Keff and its details and thermal hydraulic
parameters such as: power density, specific power, volumetric heat
rate, released power per fuel volume unit, volume and mass of clad
and fuel (consisting fissile and fertile fuels), be calculated and
compared together. By this comparing the efficiency and
modification of third generation nuclear reactors than second
generation which have same power can be distinguished.
In order to calculate the cited parameters, some information
such as: core dimensions, the pitch of lattice, the fuel matter, the
percent of enrichment and the kind of coolant are used. For
calculating the neutronic parameters, a neutronic program entitled:
SIXFAC and also related formulas have been used. Meantime for
calculating the thermal hydraulic and other parameters, analytical
method and related formulas have been applied.