Abstract: The machining of Carbon Fiber Reinforced Plastics
has come to constitute a significant challenge for many fields of
industry. The resulting surface finish of machined parts is of primary
concern for several reasons, including contact quality and impact on
the assembly. Therefore, the characterization and prediction of
roughness based on machining parameters are crucial for costeffective
operations. In this study, a PCD tool comprised of two
straight flutes was used to trim 32-ply carbon fiber laminates in a bid
to analyze the effects of the feed rate and the cutting speed on the
surface roughness. The results show that while the speed has but a
slight impact on the surface finish, the feed rate for its part affects it
strongly. A detailed study was also conducted on the effect of fiber
orientation on surface roughness, for quasi-isotropic laminates used
in aerospace. The resulting roughness profiles for the four-ply
orientation lay-up were compared, and it was found that fiber angle is
a critical parameter relating to surface roughness. One of the four
orientations studied led to very poor surface finishes, and
characteristic roughness profiles were identified and found to only
relate to the ply orientations of multilayer carbon fiber laminates.
Abstract: Power line communications may be used as a data
communication channel in public and indoor distribution networks so
that it does not require the installing of new cables. Industrial low
voltage distribution network may be utilized for data transfer
required by the on-line condition monitoring of electric motors. This
paper presents a pilot distribution network for modeling low voltage
power line as data transfer channel. The signal attenuation in
communication channels in the pilot environment is presented and
the analysis is done by varying the corresponding parameters for the
signal attenuation.
Abstract: The paper presents a comparative performance of the
models developed to predict 28 days compressive strengths using
neural network techniques for data taken from literature (ANN-I) and
data developed experimentally for SCC containing bottom ash as
partial replacement of fine aggregates (ANN-II). The data used in the
models are arranged in the format of six and eight input parameters
that cover the contents of cement, sand, coarse aggregate, fly ash as
partial replacement of cement, bottom ash as partial replacement of
sand, water and water/powder ratio, superplasticizer dosage and an
output parameter that is 28-days compressive strength and
compressive strengths at 7 days, 28 days, 90 days and 365 days,
respectively for ANN-I and ANN-II. The importance of different
input parameters is also given for predicting the strengths at various
ages using neural network. The model developed from literature data
could be easily extended to the experimental data, with bottom ash as
partial replacement of sand with some modifications.
Abstract: In order to derive important parameters concerning
mobile subscriber MS with ongoing calls in Low Earth Orbit Mobile
Satellite Systems LEO MSSs, a positioning system had to be
integrated into MSS in order to localize mobile subscribers MSs and
track them during the connection. Such integration is regarded as a
complex implementation. We propose in this paper a novel method
based on advantages of mobility model of Low Earth Orbit Mobile
Satellite System LEO MSS which allows the evaluation of instant of
subsequent handover of a MS even if its location is unknown. This
method is utilized to propose a Dynamic Channel Reservation DCRlike
scheme based on the DCR scheme previously proposed in
literature. Results presented show that DCR-like technique gives
different QoS performance than DCR. Indeed, an improve in
handover blocking probability and an increase in new call blocking
probability are observed for the DCR-like technique.
Abstract: Several optimization algorithms specifically applied to
the problem of Operation Planning of Hydrothermal Power Systems
have been developed and are used. Although providing solutions to
various problems encountered, these algorithms have some
weaknesses, difficulties in convergence, simplification of the original
formulation of the problem, or owing to the complexity of the
objective function. Thus, this paper presents the development of a
computational tool for solving optimization problem identified and to
provide the User an easy handling. Adopted as intelligent
optimization technique, Genetic Algorithms and programming
language Java. First made the modeling of the chromosomes, then
implemented the function assessment of the problem and the
operators involved, and finally the drafting of the graphical interfaces
for access to the User. The program has managed to relate a coherent
performance in problem resolution without the need for
simplification of the calculations together with the ease of
manipulating the parameters of simulation and visualization of output
results.
Abstract: The aim of this work is to investigate on the internalflow
patterns in a plate heat exchanger channel, which affect the
rate of sedimentation fouling on the heat transfer surface of the
plate heat exchanger. The research methodologies were the
computer simulation using Computational Fluid Dynamics (CFD)
and the experimental works. COMSOL MULTIPHYSICS™
Version 3.3 was used to simulate the velocity flow fields to verify
the low and high flow regions. The results from the CFD technique
were then compared with the images obtained from the
experiments in which the fouling test rig was set up with a singlechannel
plate heat exchanger to monitor the fouling of calcium
carbonate. Two parameters were varied i.e., the crossing angle of
the two plate: 55/55, 10/10, and 55/10 degree, and the fluid flow
rate at the inlet: 0.0566, 0.1132 and 0.1698 m/s. The type of plate
“GX-12" (the surface area 0.12 m2, the depth 2.9 mm, the width of
fluid flow 215 mm and the thickness of stainless plate of 0.5 mm)
was used in this study. The results indicated that the velocity
distribution for the case of 55/55 degree seems to be very well
organized when compared with the others. Also, an increase in the
inlet velocity resulted in the reduction of fouling rate on the surface
of plate heat exchangers.
Abstract: Due to their high power-to-weight ratio and low cost, pneumatic actuators are attractive for robotics and automation applications; however, achieving fast and accurate control of their position have been known as a complex control problem. The paper presents a methodology for obtaining controllers that achieve high position accuracy and preserve the closed-loop characteristics over a broad operating range. Experimentation with a number of conventional (or "classical") three-term controllers shows that, as repeated operations accumulate, the characteristics of the pneumatic actuator change requiring frequent re-tuning of the controller parameters (PID gains). Furthermore, three-term controllers are found to perform poorly in recovering the closed-loop system after the application of load or other external disturbances. The key reason for these problems lies in the non-linear exchange of energy inside the cylinder relating, in particular, to the complex friction forces that develop on the piston-wall interface. In order to overcome this problem but still remain within the boundaries of classical control methods, we designed an auto selective classicaql controller so that the system performance would benefit from all three control gains (KP, Kd, Ki) according to system requirements and the characteristics of each type of controller. This challenging experimentation took place for consistent performance in the face of modelling imprecision and disturbances. In the work presented, a selective PID controller is presented for an experimental rig comprising an air cylinder driven by a variable-opening pneumatic valve and equipped with position and pressure sensors. The paper reports on tests carried out to investigate the capability of this specific controller to achieve consistent control performance under, repeated operations and other changes in operating conditions.
Abstract: Hospitals in southern Hualien teamed with the
Hypertension Joint Care Network. Working with the network, the
team provided a special designed health education to the individual
who had been identified as a hypertension patient in the outpatient
department. Some metabolism improvements achieved. This is a
retrospective study by purposively taking 106 patients from a hospital
between 2008 and 2010. Records of before and after education
intervention of the objects was collected and analyzed to see the how
the intervention affected the patients- hypertension control via clinical
parameter monitoring. The results showed that the clinical indicators,
the LDL-C, the cholesterol and the systolic blood pressure were
significantly improved. The study provides evidence for the
effectiveness of the network in controlling hypertension.
Abstract: By analyzing the sources of energy and power
loss in PWM (Pulse Width Modulation) controlled drivers of
water electrolysis cells, it is possible to reduce the power
dissipation and enhance the efficiency of such hydrogen
production units. A PWM controlled power driver is based on
a semiconductor switching element where its power
dissipation might be a remarkable fraction of the total power
demand of an electrolysis system. Power dissipation in a
semiconductor switching element is related to many different
parameters which could be fitted into two main categories:
switching losses and conduction losses. Conduction losses are
directly related to the built, structure and capabilities of a
switching device itself and indeed the conditions in which the
element is handling the switching application such as voltage,
current, temperature and of course the fabrication technology.
On the other hand, switching losses have some other
influencing variables other than the mentioned such as control
system, switching method and power electronics circuitry of
the PWM power driver. By analyzings the characteristics of
recently developed power switching transistors from different
families of Bipolar Junction Transistors (BJT), Metal Oxide
Semiconductor Field Effect Transistors (MOSFET) and
Insulated Gate Bipolar Transistors (IGBT), some
recommendations are made in this paper which are able to
lead to achieve higher hydrogen production efficiency by
utilizing PWM controlled water electrolysis cells.
Abstract: The rheological properties of light crude oil and its mixture with water were investigated experimentally. These rheological properties include steady flow behavior, yield stress, transient flow behavior, and viscoelastic behavior. A RheoStress RS600 rheometer was employed in all of the rheological examination tests. The light crude oil exhibits a Newtonian and for emulsion exhibits a non-Newtonian shear thinning behavior over the examined shear rate range of 0.1–120 s-1. In first time, a series of samples of crude oil from the Algerian Sahara has been tested and the results expressed in terms of τ=f(γ) have demonstrated their Newtonian character for the temperature included in [20°C, 70°C]. In second time and at T=20°C, the oil-water emulsions (30%, 50% and 70%) by volume of water), thermodynamically stable, have demonstrated a non-Newtonian rheological behavior that is to say, Herschel-Bulkley and Bingham types. For each type of crude oil-water emulsion, the rheological parameters are calculated by numerical treatment of results.
Abstract: Tribological behavior and wear regimes of ascast
and heattreted Al-Cu-Mg matrix composites containing SiC
particles were studied using a pin-on-disc wear testing apparatus
against an EN32 steel counterface giving emphasis on wear rate as
a function of applied pressures (0.2, 0.6, 1.0 and 1.4 MPa) at
different sliding distances (1000, 2000, 3000, 4000 and 5000
meters) and at a fixed sliding speed of 3.35m/s. The results showed
that the composite exhibited lower wear rate than that of the matrix
alloy and the wear rate of the composites is noted to be invariant to
the sliding distance and is reducing by heat treatment. Wear
regimes such as low, mild and severe wear were observed as per the
Archard-s wear calculations. It is very interesting to note that the
mild wear is almost constant in all the wear regimes.
Abstract: Sensors possess several properties of physical
measures. Whether devices that convert a sensed signal into an
electrical signal, chemical sensors and biosensors, thus all these
sensors can be considered as an interface between the physical and
electrical equipment. The problem is the analysis of the multitudes of
saved settings as input variables. However, they do not all have the
same level of influence on the outputs. In order to identify the most
sensitive parameters, those that can guide users in gathering
information on the ground and in the process of model calibration
and sensitivity analysis for the effect of each change made.
Mathematical models used for processing become very complex.
In this paper a fuzzy rule-based system is proposed as a solution
for this problem. The system collects the available signals
information from sensors. Moreover, the system allows the study of
the influence of the various factors that take part in the decision
system. Since its inception fuzzy set theory has been regarded as a
formalism suitable to deal with the imprecision intrinsic to many
problems. At the same time, fuzzy sets allow to use symbolic models.
In this study an example was applied for resolving variety of
physiological parameters that define human health state. The
application system was done for medical diagnosis help. The inputs
are the signals expressed the cardiovascular system parameters, blood
pressure, Respiratory system paramsystem was done, it will be able
to predict the state of patient according any input values.
Abstract: This article presents a detailed analysis and comparative
performance evaluation of model reference adaptive control systems.
In contrast to classical control theory, adaptive control methods allow
to deal with time-variant processes. Inspired by the works [1] and
[2], two methods based on the MIT rule and Lyapunov rule are
applied to a linear first order system. The system is simulated and
it is investigated how changes to the adaptation gain affect the
system performance. Furthermore, variations in the reference model
parameters, that is changing the desired closed-loop behaviour are
examinded.
Abstract: In the present study, the effects of ultrasound as
emerging technology were investigated on germination stimulation,
amount of alpha-amylase activity on dry barley seeds before steeping
stage of malting process. All experiments were carried out at 20 KHz
on the ultrasonic generator in 3 different ultrasonic intensities (20, 60
and 100% setting from total power of device) and time (5, 10 and 15
min) at constant temperature (30C). For determining the effects of
these parameters on enzyme the Fuwa method assay based on the
decreased staining value of blue starch–iodine complexes employed
for measurement an activity. The results of these assays were
analyzed by Qualitek4 software using the Taguchi statistical method
to evaluate the factor-s effects on enzyme activity. It has been found
that when malting barley is irradiated with an ultrasonic power, a
stimulating effect occurs as to the enzyme activity.
Abstract: The aim of this paper is to study the oblique
stagnation point flow on vertical plate with uniform surface heat flux
in presence of magnetic field. Using Stream function, partial
differential equations corresponding to the momentum and energy
equations are converted into non-linear ordinary differential
equations. Numerical solutions of these equations are obtained using
Runge-Kutta Fehlberg method with the help of shooting technique.
In the present work the effects of striking angle, magnetic field
parameter, Grashoff number, the Prandtl number on velocity and heat
transfer characteristics have been discussed. Effect of above
mentioned parameter on the position of stagnation point are also
studied.
Abstract: IETF RFC 2002 originally introduced the wireless
Mobile-IP protocol to support portable IP addresses for mobile
devices that often change their network access points to the Internet.
The inefficiency of this protocol mainly within the handoff
management produces large end-to-end packet delays, during
registration process, and further degrades the system efficiency due to
packet losses between subnets. The criterion to initiate a simple and
fast full-duplex connection between the home agent and foreign
agent, to reduce the roaming duration, is a very important issue to be
considered by a work in this paper. State-transition Petri-Nets of the
modeling scenario-based CIA: communication inter-agents procedure
as an extension to the basic Mobile-IP registration process was
designed and manipulated. The heuristic of configuration file during
practical Setup session for registration parameters, on Cisco platform
Router-1760 using IOS 12.3 (15)T is created. Finally, stand-alone
performance simulations results from Simulink Matlab, within each
subnet and also between subnets, are illustrated for reporting better
end-to-end packet delays. Results verified the effectiveness of our
Mathcad analytical manipulation and experimental implementation. It
showed lower values of end-to-end packet delay for Mobile-IP using
CIA procedure. Furthermore, it reported packets flow between
subnets to improve packet losses between subnets.
Abstract: Analysis of blood vessel mechanics in normal and
diseased conditions is essential for disease research, medical device
design and treatment planning. In this work, 3D finite element
models of normal vessel and atherosclerotic vessel with 50% plaque
deposition were developed. The developed models were meshed
using finite number of tetrahedral elements. The developed models
were simulated using actual blood pressure signals. Based on the
transient analysis performed on the developed models, the parameters
such as total displacement, strain energy density and entropy per unit
volume were obtained. Further, the obtained parameters were used to
develop artificial neural network models for analyzing normal and
atherosclerotic blood vessels. In this paper, the objectives of the
study, methodology and significant observations are presented.
Abstract: This paper proposes a method for speckle reduction in
medical ultrasound imaging while preserving the edges with the
added advantages of adaptive noise filtering and speed. A nonlinear
image diffusion method that incorporates local image parameter,
namely, scatterer density in addition to gradient, to weight the
nonlinear diffusion process, is proposed. The method was tested for
the isotropic case with a contrast detail phantom and varieties of
clinical ultrasound images, and then compared to linear and some
other diffusion enhancement methods. Different diffusion parameters
were tested and tuned to best reduce speckle noise and preserve
edges. The method showed superior performance measured both
quantitatively and qualitatively when incorporating scatterer density
into the diffusivity function. The proposed filter can be used as a
preprocessing step for ultrasound image enhancement before
applying automatic segmentation, automatic volumetric calculations,
or 3D ultrasound volume rendering.
Abstract: This paper evaluates the dividend payments for general
claim size distributions in the presence of a dividend barrier. The
surplus of a company is modeled using the classical risk process
perturbed by diffusion, and in addition, it is assumed to accrue interest
at a constant rate. After presenting the integro-differential equation
with initial conditions that dividend payments satisfies, the paper
derives a useful expression of the dividend payments by employing
the theory of Volterra equation. Furthermore, the optimal value of
dividend barrier is found. Finally, numerical examples illustrate the
optimality of optimal dividend barrier and the effects of parameters
on dividend payments.
Abstract: With getting older in the whole population, the
prevalence of stroke and its residual disability is getting higher and
higher recently in Taiwan. The functional electrical stimulation
cycling system (FESCS) is useful for hemiplegic patients. Because
that the muscle of stroke patients is under hybrid activation. The raw
electromyography (EMG) represents the residual muscle force of
stroke subject whereas the peak-to-peak of stimulus EMG indicates the
force enhancement benefiting from ES. It seems that EMG signals
could be used for a parameter of feedback control mechanism. So, we
design the feedback control protocol of FESCS, it includes
physiological signal recorder, FPGA biomedical module, DAC and
electrical stimulation circuit. Using the intensity of real-time EMG
signal obtained from patients, as a feedback control method for the
output voltage of FES-cycling system.