Abstract: Autoregressive Moving average (ARMA) is a parametric based method of signal representation. It is suitable for problems in which the signal can be modeled by explicit known source functions with a few adjustable parameters. Various methods have been suggested for the coefficients determination among which are Prony, Pade, Autocorrelation, Covariance and most recently, the use of Artificial Neural Network technique. In this paper, the method of using Artificial Neural network (ANN) technique is compared with some known and widely acceptable techniques. The comparisons is entirely based on the value of the coefficients obtained. Result obtained shows that the use of ANN also gives accurate in computing the coefficients of an ARMA system.
Abstract: In this study, an experimental investigation was carried
out to fix CO2 into the electronic arc furnace (EAF) reducing slag from
stainless steelmaking process under wet grinding. The slag was ground
by the vibrating ball mill with the CO2 and pure water. The reaction
behavior was monitored with constant pressure method, and the
change of CO2 volume in the experimental system with grinding time
was measured. It was found that the CO2 absorption occurred as soon
as the grinding started. The CO2 absorption under wet grinding was
significantly larger than that under dry grinding. Generally, the
amount of CO2 absorption increased as the amount of water, the
amount of slag, the diameter of alumina ball and the initial pressure of
CO2 increased. However, the initial absorption rate was scarcely
influenced by the experimental conditions except for the initial CO2
pressure. According to this research, the CO2 reacted with the CaO
inside the slag to form CaCO3.
Abstract: Polyurethane foam (PUF) is formed by a chemical
reaction of polyol and isocyanate. The aim is to understand the
impact of Silicone on synthesizing polyurethane in differentiate
volume of molding. The method used was one step process, which is
simultaneously caried out a blending polyol (petroleum polyol and
soybean polyol), a TDI (2,4):MDI (4,4-) (80:20), a distilled water,
and a silicone. The properties of the material were measured via a
number of parameters, which are polymer density, compressive
strength, and cellular structures. It is found that density of
polyurethane using silicone with volume of molding either 250 ml or
500 ml is lower than without using silicone.
Abstract: The reservoir of Kowsar dam supply water for
different usages such as aquaculture farms , drinking, agricultural and
industrial usages for some provinces in south of Iran. The Kowsar
dam is located next to the city of Dehdashat in Kohgiluye and
Boyerahmad province in southern Iran. There are some towns and
villages on the Kowsar dam watersheds, which Dehdasht and Choram
are the most important and populated twons in this area, which can to
be sources of pollution for water reservoir of the Kowsar dam . This
study was done to determine of water pollution of the Kowsar dam
reservoir which is one of the most important water resources of
Kohkiloye and Boyerahmad and Bushehr provinces in south-west
Iran. In this study , water samples during 12 months were collected to
examine Biochemical Oxygen Demand (BOD) and Dissolved
Oxygen(DO) as a criterion for evaluation of water pollution of the
reservoir. In summary ,the study has shown Maximum, average and
minimum levels of BOD have observed 25.9 ,9.15 and 2.3 mg/L
respectively and statistical parameters of data such as standard
deviation , variance and skewness have calculated 7.88, 62 and 1.54
respectively. Finally the results were compared with Iranian national
standards. Among the analyzed samples, as the maximum value of
BOD (25.9 mg/L) was observed at the May 2010 , was within the
maximum admissible limits by the Iranian standards.
Abstract: This paper presents the elastic buckling of
homogeneous beams with a pair of piezoelectric layers surface
bonded on both sides of the beams. The displacement field of beam is
assumed based on the Engesser-Timoshenko beam theory.
Applying the Hamilton's principle, the equilibrium equation is
established. The influences of applied voltage, dimensionless
geometrical parameter and piezoelectric thickness on the critical
buckling load of beam are presented. To investigate the accuracy of
the present analysis, a compression study is carried out with a known
data.
Abstract: ORC (Organic Rankine Cycle) has potential of
reducing consumption of fossil fuels and has many favorable
characteristics to exploit low-temperature heat sources. In this work
thermodynamic performance of ORC with regeneration is
comparatively assessed for various working fluids. Special attention is
paid to the effects of system parameters such as the turbine inlet
pressure on the characteristics of the system such as net work
production, heat input, volumetric flow rate per 1 MW of net work and
quality of the working fluid at turbine exit as well as thermal
efficiency. Results show that for a given source the thermal efficiency
generally increases with increasing of the turbine inlet pressure
however has optimal condition for working fluids of low critical
pressure such as iso-pentane or n-pentane.
Abstract: Psoriasis is a widespread skin disease affecting up to 2% population with plaque psoriasis accounting to about 80%. It can be identified as a red lesion and for the higher severity the lesion is usually covered with rough scale. Psoriasis Area Severity Index (PASI) scoring is the gold standard method for measuring psoriasis severity. Scaliness is one of PASI parameter that needs to be quantified in PASI scoring. Surface roughness of lesion can be used as a scaliness feature, since existing scale on lesion surface makes the lesion rougher. The dermatologist usually assesses the severity through their tactile sense, therefore direct contact between doctor and patient is required. The problem is the doctor may not assess the lesion objectively. In this paper, a digital image analysis technique is developed to objectively determine the scaliness of the psoriasis lesion and provide the PASI scaliness score. Psoriasis lesion is modelled by a rough surface. The rough surface is created by superimposing a smooth average (curve) surface with a triangular waveform. For roughness determination, a polynomial surface fitting is used to estimate average surface followed by a subtraction between rough and average surface to give elevation surface (surface deviations). Roughness index is calculated by using average roughness equation to the height map matrix. The roughness algorithm has been tested to 444 lesion models. From roughness validation result, only 6 models can not be accepted (percentage error is greater than 10%). These errors occur due the scanned image quality. Roughness algorithm is validated for roughness measurement on abrasive papers at flat surface. The Pearson-s correlation coefficient of grade value (G) of abrasive paper and Ra is -0.9488, its shows there is a strong relation between G and Ra. The algorithm needs to be improved by surface filtering, especially to overcome a problem with noisy data.
Abstract: The proper selection of the AC-side passive filter
interconnecting the voltage source converter to the power supply is
essential to obtain satisfactory performances of an active power filter
system. The use of the LCL-type filter has the advantage of
eliminating the high frequency switching harmonics in the current
injected into the power supply. This paper is mainly focused on
analyzing the influence of the interface filter parameters on the active
filtering performances. Some design aspects are pointed out. Thus,
the design of the AC interface filter starts from transfer functions by
imposing the filter performance which refers to the significant current
attenuation of the switching harmonics without affecting the
harmonics to be compensated. A Matlab/Simulink model of the entire
active filtering system including a concrete nonlinear load has been
developed to examine the system performances. It is shown that a
gamma LC filter could accomplish the attenuation requirement of the
current provided by converter. Moreover, the existence of an optimal
value of the grid-side inductance which minimizes the total harmonic
distortion factor of the power supply current is pointed out.
Nevertheless, a small converter-side inductance and a damping
resistance in series with the filter capacitance are absolutely needed
in order to keep the ripple and oscillations of the current at the
converter side within acceptable limits. The effect of change in the
LCL-filter parameters is evaluated. It is concluded that good active
filtering performances can be achieved with small values of the
capacitance and converter-side inductance.
Abstract: Many studies have been conducted for derivation of
attenuation relationships worldwide, however few relationships have
been developed to use for the seismic region of Iranian plateau and
only few of these studies have been conducted for derivation of
attenuation relationships for parameters such as uniform duration.
Uniform duration is the total time during which the acceleration is
larger than a given threshold value (default is 5% of PGA). In this
study, the database was same as that used previously by Ghodrati
Amiri et al. (2007) with same correction methods for earthquake
records in Iran. However in this study, records from earthquakes with
MS< 4.0 were excluded from this database, each record has
individually filtered afterward, and therefore the dataset has been
expanded. These new set of attenuation relationships for Iran are
derived based on tectonic conditions with soil classification into rock
and soil. Earthquake parameters were chosen to be
hypocentral distance and magnitude in order to make it easier to use
the relationships for seismic hazard analysis. Tehran is the capital
city of Iran wit ha large number of important structures. In this study,
a probabilistic approach has been utilized for seismic hazard
assessment of this city. The resulting uniform duration against return
period diagrams are suggested to be used in any projects in the area.
Abstract: In this paper we report the technique of optical
induction of 2 and 3-dimensional (2D and 3D) photonic lattices in
photorefractive materials based on diffraction grating self replication
-Talbot effect. 1D and 2D different rotational symmery diffraction
masks with the periods of few tens micrometers and 532 nm cw laser
beam were used in the experiments to form an intensity modulated
light beam profile. A few hundred micrometric scale replications of
mask generated intensity structures along the beam propagation axis
were observed. Up to 20 high contrast replications were detected for
1D annular mask with 30
Abstract: In this work, stationary hot-wire measurements are
carried out to investigate the characteristics of a round free jet in its
potential core region (0 ≤ x/d ≤ 10). Measurements are carried out on
an incompressible round jet for a range of Reynolds numbers from
4000 to 8000, calculated based on the jet exit mean velocity and the
nozzle diameter. The effect of flow velocity on the development
characteristics of the jet in the core region is analyzed. Timeaveraged
statistics, spectra of velocity and its higher order moments
are presented and explained.
Abstract: Composite of Celatom-ZeoliteY (Cel-ZY) was used to
remove cobalt ion from an aqueous solution using batch mode.
ZeoliteY has successfully superimposed on Celatom FW-14 surface
using hydrothermal treatment .The product was synthesized as a
novel of hierarchical porous material. It was observed from the
results that Cel-ZY has higher ability to remove cobalt ions than the
pure ZeoliteY powder (PZY) synthesized under the same conditions.
Several parameters were studied in this project to investigate the
effect of removal cobalt ion such as pH and initial cobalt
concentration. It was clearly observed that the uptake of cobalt ions
was affected with increase these parameters. The results proved that
the product can be used effectively to remove Co2+ ions from
wastewater as an environmentally friendly alternative.
Abstract: MOC (method of cell) is a new method of investigating
wave propagating in material with periodic microstructure, and can
reflect the effect of microstructure. Wave propagation in periodically
laminated medium consisting of linearly elastic layers can be treated
as a special application of this method. In this paper, it was used to
simulate the dynamic response of carbon-phenolic to impulsive
loading under certain boundary conditions. From the comparison
between the results obtained from this method and the exact results
based on propagator matrix theory, excellent agreement is achieved.
Conclusion can be made that the oscillation periodicity is decided by
the thickness of sub-cells. In the end, the NHDMOC method, which
permits studying stress wave propagation with one dimensional strain,
was applied to study the one-dimensional stress wave propagation. In
this paper, the ZWT nonlinear visco-elastic constitutive relationship
with 7 parameters, NHDMOC, and corresponding equations were
deduced. The equations were verified, comparing the elastic stress
wave propagation in SHPB with, respectively, the elastic and the
visco-elastic bar. Finally the dispersion and attenuation of stress wave
in SHPB with visco-elastic bar was studied.
Abstract: In this study, the sorption of Malachite green (MG) on Hydrilla verticillata biomass, a submerged aquatic plant, was investigated in a batch system. The effects of operating parameters such as temperature, adsorbent dosage, contact time, adsorbent size, and agitation speed on the sorption of Malachite green were analyzed using response surface methodology (RSM). The proposed quadratic model for central composite design (CCD) fitted very well to the experimental data that it could be used to navigate the design space according to ANOVA results. The optimum sorption conditions were determined as temperature - 43.5oC, adsorbent dosage - 0.26g, contact time - 200min, adsorbent size - 0.205mm (65mesh), and agitation speed - 230rpm. The Langmuir and Freundlich isotherm models were applied to the equilibrium data. The maximum monolayer coverage capacity of Hydrilla verticillata biomass for MG was found to be 91.97 mg/g at an initial pH 8.0 indicating that the optimum sorption initial pH. The external and intra particle diffusion models were also applied to sorption data of Hydrilla verticillata biomass with MG, and it was found that both the external diffusion as well as intra particle diffusion contributes to the actual sorption process. The pseudo-second order kinetic model described the MG sorption process with a good fitting.
Abstract: The aim of this study was to synthesize the single
walled carbon nanotubes (SWCNTs) and determine their hydrogen
storage capacities. SWCNTs were firstly synthesized by chemical
vapor deposition (CVD) of acetylene (C2H2) on a magnesium oxide
(MgO) powder impregnated with an iron nitrate (Fe(NO3)3·9H2O)
solution. The synthesis parameters were selected as: the synthesis
temperature of 800°C, the iron content in the precursor of 5% and the
synthesis time of 30 min. Purification process of SWCNTs was
fulfilled by microwave digestion at three different temperatures (120,
150 and 200 °C), three different acid concentrations (0.5, 1 and 1.5
M) and for three different time intervals (15, 30 and 60 min). Nitric
acid (HNO3) was used in the removal of the metal catalysts. The
hydrogen storage capacities of the purified materials were measured
using volumetric method at the liquid nitrogen temperature and gas
pressure up to 100 bar. The effects of the purification conditions such
as temperature, time and acid concentration on hydrogen adsorption
were investigated.
Abstract: We developed a method based on quasi-molecular
modelling to simulate the fall of water drops on horizontally smooth
and rough surfaces. Each quasi-molecule was a group of particles
that interacted in a fashion entirely analogous to classical Newtonian
molecular interactions. When a falling water droplet was simulated at
low impact velocity on both smooth and rough surfaces, the droplets
moved periodically (i.e. the droplets moved up and down for a
certain period, finally they stopped moving and reached a steady
state), spreading and recoiling without splash or break-up. Spreading
rates of falling water droplets increased rapidly as time increased
until the spreading rate reached its steady state at time t ~ 0.25 s for
rough surface and t ~ 0.40 s for smooth surface. The droplet height
above both surfaces decreased as time increased, remained constant
after the droplet diameter attained a maximum value and reached its
steady state at time t ~ 0.4 s. However, rough surface had higher
spreading rates of falling water droplets and lower height on the
surface than smooth one.
Abstract: Helical milling operations are used to generate or
enlarge boreholes by means of a milling tool. The bore diameter can be
adjusted through the diameter of the helical path. The kinematics of
helical milling on a three axis machine tool is analysed firstly. The
relationships between processing parameters, cutting tool geometry
characters with machined hole feature are formulated. The feed motion
of the cutting tool has been decomposed to plane circular feed and
axial linear motion. In this paper, the time varying cutting forces acted
on the side cutting edges and end cutting edges of the flat end cylinder
miller is analysed using a discrete method separately. These two
components then are combined to produce the cutting force model
considering the complicated interaction between the cutters and
workpiece. The time varying cutting force model describes the
instantaneous cutting force during processing. This model could be
used to predict cutting force, calculate statics deflection of cutter and
workpiece, and also could be the foundation of dynamics model and
predicting chatter limitation of the helical milling operations.
Abstract: The rate of production of main products of the Fischer-Tropsch reactions over Fe/HZSM5 bifunctional catalyst in a fixed bed reactor is investigated at a broad range of temperature, pressure, space velocity, H2/CO feed molar ratio and CO2, CH4 and water flow rates. Model discrimination and parameter estimation were performed according to the integral method of kinetic analysis. Due to lack of mechanism development for Fisher – Tropsch Synthesis on bifunctional catalysts, 26 different models were tested and the best model is selected. Comprehensive one and two dimensional heterogeneous reactor models are developed to simulate the performance of fixed-bed Fischer – Tropsch reactors. To reduce computational time for optimization purposes, an Artificial Feed Forward Neural Network (AFFNN) has been used to describe intra particle mass and heat transfer diffusion in the catalyst pellet. It is seen that products' reaction rates have direct relation with H2 partial pressure and reverse relation with CO partial pressure. The results show that the hybrid model has good agreement with rigorous mechanistic model, favoring that the hybrid model is about 25-30 times faster.
Abstract: A self-association model has been used to understand
the concentration dependence of free energy of mixing (GM), heat of
mixing (HM), entropy of mixing (SM), activity (a) and microscopic
structures, such as concentration fluctuation in long wavelength limit
(Scc(0)) and Warren-Cowley short range order parameter ( 1
α )for Cu-
Tl molten alloys at 1573K. A comparative study of surface tension of
the alloys in the liquid state at that temperature has also been carried
out theoretically as function of composition in the light of Butler-s
model, Prasad-s model and quasi-chemical approach. Most of the
computed thermodynamic properties have been found in agreement
with the experimental values. The analysis reveals that the Cu-Tl
molten alloys at 1573K represent a segregating system at all
concentrations with moderate interaction. Surface tensions computed
from different approaches have been found to be comparable to each
other showing increment with the composition of copper.
Abstract: In this study, the conversion of n-pentane to aromatics is investigated on HZSM-5 zeolites modified by Ga ion-exchange and silylation using tetraethyl orthosilicate (TEOS) via chemical liquid deposition (CLD). The effect of SiO2/Al2O3 ratios of HZSM-5 was also studied. Parameters in preparing catalysts i.e. TEOS loading and cycles of deposition were varied to obtain the optimal condition for enhancing p-xylene selectivity. The highest p-xylene selectivity 99.7% was achieved when the amount of TEOS was 20 vol.%.The catalysts were characterized by TPD, TPO, XRF, and BET. Results show that the conversion of n-pentane was influenced remarkably by the SiO2/Al2O3 ratios of HZSM-5. The highest p-xylene selectivity 99.7% was achieved when the amount of TEOS was 20 vol.%. And cycles of deposition greatly improves HZSM-5 shape-selectivity.