Abstract: This paper presents a part of research on the
rheological properties of bitumen modified by thermoplastic namely
linear low density polyethylene (LLDPE), high density polyethylene
(HDPE) and polypropylene (PP) and its interaction with 80 pen base
bitumen. As it is known that the modification of bitumen by the use
of polymers enhances its performance characteristics but at the same
time significantly alters its rheological properties. The rheological
study of polymer modified bitumen (PMB) was made through
penetration, ring & ball softening point and viscosity test. The results
were then related to the changes in the rheological properties of
polymer modified bitumen. It was observed that thermoplastic
copolymer shows profound effect on penetration rather than
softening point. The viscoelastic behavior of polymer modified
bitumen depend on the concentration of polymer, mixing
temperature, mixing technique, solvating power of base bitumen and
molecular structure of polymer used. PP offer better blend in
comparison to HDPE and LLDPE. The viscosity of base bitumen was
also enhanced with the addition of polymer. The pseudoplastic
behavior was more prominent for HDPE and LLDPE than PP. Best
results were obtained when polymer concentration was kept below
3%
Abstract: Reinforced Concrete (RC) structures strengthened
with fiber reinforced polymer (FRP) lack in thermal resistance under
elevated temperatures in the event of fire. This phenomenon led to
the lining of strengthened concrete with thin high performance
cementitious composites (THPCC) to protect the substrate against
elevated temperature. Elevated temperature effects on THPCC, based
on different cementitious materials have been studied in the past but
high-alumina cement (HAC)-based THPCC have not been well
characterized. This research study will focus on the THPCC based on
HAC replaced by 60%, 70%, 80% and 85% of ground granulated
blast furnace slag (GGBS). Samples were evaluated by the
measurement of their mechanical strength (28 & 56 days of curing)
after exposed to 400°C, 600°C and 28°C of room temperature for
comparison and corroborated by their microstructure study. Results
showed that among all mixtures, the mix containing only HAC
showed the highest compressive strength after exposed to 600°C as
compared to other mixtures. However, the tensile strength of THPCC
made of HAC and 60% GGBS content was comparable to the
THPCC with HAC only after exposed to 600°C. Field emission
scanning electron microscopy (FESEM) images of THPCC
accompanying Energy Dispersive X-ray (EDX) microanalysis
revealed that the microstructure deteriorated considerably after
exposure to elevated temperatures which led to the decrease in
mechanical strength.
Abstract: In modern agriculture, polymeric hydrogels are
known as a component able to hold an amount of water due to their
3-dimensional network structure and their tendency to absorb water
in humid environments. In addition, these hydrogels are able to
controllably release the fertilisers and pesticides loaded in them.
Therefore, they deliver these materials to the plants' roots and help
them with growing. These hydrogels also reduce the pollution of
underground water sources by preventing the active components
from leaching. In this study, sIPN acrylamide based hydrogels are
synthesised by using acrylamide free radical, potassium acrylate, and
linear polyvinyl alcohol. Ammonium nitrate is loaded in the hydrogel
as the fertiliser. The effect of various amounts of monomers and
linear polymer, measured in molar ratio, on the swelling rate,
equilibrium swelling, and release of ammonium nitrate is studied.
Abstract: The main aim is to perform mutational analysis of CTLA4 gene Exon 1 in SLE patients. A total of 61 SLE patients fulfilling “American College of Rheumatology (ACR) criteria" and 61 controls were enrolled in this study. The region of CTLA4 gene exon 1 was amplified by using Step-down PCR technique. Extracted DNA of band 354 bp was sequenced to analyze mutations in the exon-1 of CTLA-4 gene. Further, protein sequences were identified from nucleotide sequences of CTLA4 Exon 1 by using Expasy software and through Blast P software it was found that CTLA4 protein sequences of Pakistani SLE patients were similar to that of Chinese SLE population. No variations were found after patients sequences were compared with that of the control sequence. Furthermore it was found that CTLA4 protein sequences of Pakistani SLE patients were similar to that of Chinese SLE population. Thus CTLA4 gene may not be responsible for an autoimmune disease SLE.
Abstract: The study investigated the hydrophilic to hydrophobic
transition of modified polyacrylamide hydrogel with the inclusion of
N-isopropylacrylamide (NIAM). The modification was done by
mimicking micellar polymerization, which resulted in better
arrangement of NIAM chains in the polyacrylamide network. The
degree of NIAM arrangement is described by NH number. The
hydrophilic to hydrophobic transition was measured through the
partition coefficient, K, of Orange II and Methylene Blue in hydrogel
and in water. These dyes were chosen as a model for solutes with
different degree of hydrophobicity. The study showed that the
hydrogel with higher NH values resulted in better solubility of both
dyes. Moreover, in temperature above the lower critical solution
temperature (LCST) of Poly(N-isopropylacrylamide) (PNIAM)also
caused the collapse of NIPAM chains which results in a more
hydrophobic environment that increases the solubility of Methylene
Blue and decreases the solubility of Orange II in the hydrogels with
NIPAM present.
Abstract: Bean common mosaic necrosis virus (BCMNV) is a
potyvirus with a worldwide distribution. This virus causes serious
economic losses in Iran in many leguminoses. During 20008,
samples were collected from soybeans fields in Tehran Province.
Four isolates (S1, S2 and S3) were inoculated on 15 species of
Cucurbitaceae, Chenopodiaceae, Solanacae and Leguminosae.
Chenopodium quinoa and C. amaranticolor.
Did not developed any symptoms.all isolates caused mosaic
symptoms on Phaseolus vulgaris cv. Red Kidney and P. vulgaris cv.
Bountiful. The molecular weights of coat protein using SDS-PAGE
and western blotting were estimated at 33 kDa. Reverse transcription
polymerase chain reaction (RT-PCR) was performed using one
primer pairs designed by L. XU et al. An approximately 920 bp
fragment was amplified with a specific primer.
Abstract: The polyfunctional and highly reactive bio-polymer,
the chitosan was first regioselectively converted into dialkylated
chitosan using dimsyl anionic solution(NaH in DMSO) and
bromodecane after protecting amino groups by phthalic anhydride.
The dibenzo-18-crown-6-ether, on the other hand, was converted into
its carbonyl derivatives via Duff reaction prior to incorporate into
chitosan by Schiff base formation. Thus formed diformylated
dibenzo-18-crown-6-ether was condensed with lipophilic chitosan to
prepare the novel solvent extraction reagent. The products were
characterized mainly by IR and 1H-NMR. Hence, the multidentate
crown ether-embedded polyfunctional bio-material was tested for
extraction of Pd(II) and Pt(IV) in aqueous solution.
Abstract: fibers of pure cellulose can be made from some bacteria such as acetobacter xylinum. Bacterial cellulose fibers are very pure, tens of nm across and about 0.5 micron long. The fibers are very stiff and, although nobody seems to have measured the strength of individual fibers. Their stiffness up to 70 GPa. Fundamental strengths should be at least greater than those of the best commercial polymers, but best bulk strength seems to about the same as that of steel. They can potentially be produced in industrial quantities at greatly lowered cost and water content, and with triple the yield, by a new process. This article presents a critical review of the available information on the bacterial cellulose as a biological nonwoven fabric with special emphasis on its fermentative production and applications. Characteristics of bacterial cellulose biofabric with respect to its structure and physicochemical properties are discussed. Current and potential applications of bacterial cellulose in textile, nonwoven cloth, paper, films synthetic fiber coating, food, pharmaceutical and other industries are also presented.
Abstract: Molar excess Volumes, VE ijk and speeds of sound , uijk of 2-pyrrolidinone (i) + benzene or toluene (j) + ethanol (k) ternary mixture have been measured as a function of composition at 308.15 K. The observed speeds of sound data have been utilized to determine excess isentropic compressiblities, ( E S κ )ijk of ternary (i + j + k) mixtures. Molar excess volumes, VE ijk and excess isentropic compressibilities, ( E S κ )ijk data have fitted to the Redlich-Kister equation to calculate ternary adjustable parameters and standard deviations. The Moelywn-Huggins concept (Huggins in Polymer 12: 389-399, 1971) of connectivity between the surfaces of the constituents of binary mixtures has been extended to ternary mixtures (using the concept of a connectivity parameter of third degree of molecules, 3ξ , which inturn depends on its topology) to obtain an expression that describes well the measured VE ijk and ( E S κ )ijk data.
Abstract: Tomato powder has good potential as substitute of tomato paste and other tomato products. In order to protect physicochemical properties and nutritional quality of tomato during dehydration process, investigation was carried out using different drying methods and pretreatments. Solar drier and continuous conveyor (tunnel) drier were used for dehydration where as calcium chloride (CaCl2), potassium metabisulphite (KMS), calcium chloride and potassium metabisulphite (CaCl2 +KMS), and sodium chloride (NaCl) selected for treatment.. lycopene content, dehydration ratio, rehydration ratio and non-enzymatic browning in addition to moisture, sugar and titrable acidity were studied. Results show that pre-treatment with CaCl2 and NaCl increased water removal and moisture mobility in tomato slices during drying of tomatoes. Where CaCl2 used along with KMS the NEB was recorded the least compared to other treatments and the best results were obtained while using the two chemicals in combination form. Storage studies in LDPE polymeric and metalized polyesters films showed less changes in the products packed in metallized polyester pouches and even after 6 months lycopene content did not decrease more than 20% as compared to the control sample and provide extension of shelf life in acceptable condition for 6 months. In most of the quality characteristics tunnel drier samples presented better values in comparison to solar drier.
Abstract: Conventional materials like glass, wood or metals
replacement with polymer materials is still continuing. More simple
thus cheaper production is the main reason. However due to high
energy and petrochemical prices are polymer prices increasing too.
That´s why various kinds of fillers are used to make polymers
cheaper. Of course target is to maintain or improve properties of
these compounds. In this paper are solved rheology issues of
polymers compounded with vegetal origin fibers.
Abstract: Two completely different approaches for a Gigabit
Ethernet compliant stream transmission over 50m of 1mm PMMA SI-POF have been experimentally demonstrated and are compared in this paper. The first solution is based on a commercial RC-LED
transmission and a careful optimization of the physical layer architecture, realized during the POF-PLUS EU Project. The second solution exploits the performance of an edge-emitting laser at the
transmitter side in order to avoid any sort of electrical equalization at the receiver side.
Abstract: The accelerated growth in aircraft industries desire
effectual schemes, programs, innovative designs of advanced systems
and facilities to accomplish the augmenting need for home-free air
transportation. In this paper, a contemporary conceptual design of a
cambered airfoil has been proposed in order to providing augmented
effective lift force relative to the airplane, and to eliminating
drawbacks and limitations of an airfoil in a commercial airplane by
using a kind of smart materials. This invention of an unsymmetrical
airfoil structure utilizes the amplified air momentum around the
airfoil and increased camber length to providing improved aircraft
performance and assist to enhancing the reliability of the aircraft
components. Moreover, this conjectured design helps to reducing
airplane weight and total drag.
Abstract: The psychological and physical trauma associated with the loss of a human limb can severely impact on the quality of life of an amputee rendering even the most basic of tasks very difficult. A prosthetic device can be of great benefit to the amputee in the performance of everyday human tasks. This paper outlines a proposed mechanical design of a 12 degree-of-freedom SMA actuated artificial hand. It is proposed that the SMA wires be embedded intrinsically within the hand structure which will allow for significant flexibility for use either as a prosthetic hand solution, or as part of a complete lower arm prosthetic solution. A modular approach is taken in the design facilitating ease of manufacture and assembly, and more importantly, also allows the end user to easily replace SMA wires in the event of failure. A biomimetric approach has been taken during the design process meaning that the artificial hand should replicate that of a human hand as far as is possible with due regard to functional requirements. The proposed design has been exposed to appropriate loading through the use of finite element analysis (FEA) to ensure that it is structurally sound. Theoretical analysis of the mechanical framework was also carried out to establish the limits of the angular displacement and velocity of the finger tip as well finger tip force generation. A combination of various polymers and Titanium, which are suitably lightweight, are proposed for the manufacture of the design.
Abstract: In this paper, the effect of modified clay on the
mechanical efficiency of epoxy resin is examined. Studies by X ray
diffraction and microscopic transient electron method show that
modified clay distribution in polymer area is intercalated kind.
Examination the results of mechanical tests shows that existence of
modified clay in epoxy area increases pressure yield strength, tension
module and nano composite fracture toughness in relate of pure
epoxy. By microscopic examinations it is recognized too that the
action of toughness growth of this kind of nano composite is due to
crack deflection, formation of new surfaces and fracture of clay piles.
Abstract: A new analytical method to predict the torsional
capacity and behavior of R.C multi-cell box girders strengthened with
carbon fiber reinforced polymer (CFRP) sheets is presented.
Modification was done on the Softened Truss Model (STM) in the
proposed method; the concrete torsional problem is solved by
combining the equilibrium conditions, compatibility conditions and
constitutive laws of materials by taking into account the confinement
of concrete with CFRP sheets. A specific algorithm is developed to
predict the torsional behavior of reinforced concrete multi-cell box
girders with or without strengthening by CFRP sheets. Applications
of the developed method as an assessment tool to strengthened multicell
box girders with CFRP and first analytical example that
demonstrate the contribution of the CFRP materials on the torsional
response is also included.
Abstract: In the present study, development of salbutamol
sulphate nanoparticles that adhere to gastric mucus was investigated.
Salbutamol sulphate has low bioavailability due to short transit time in
gastric. It also has a positive surface charge that provides hurdles to be
encapsulated by the positively strong mucoadhesive polymer of
chitosan. To overcome the difficulties, the surface charge of active
ingredient was modified using several nonionic and anionic
stomach-specific polymers. The nanoparticles were prepared using
ionotropic gelation technique. The evaluation involved determination
of particle size, zeta potential, entrapment efficiency, in vitro drug
release and in vitro mucoadhesion test. Results exhibited that the use
of anionic alginate polymer was more satisfactory than that of
nonionic polymer. Characteristics of the particles was nano-size, high
encapsulation efficiency, fulfilled the drug release requirements and
adhesive towards stomach for around 11 hours. This result shows that
the salbutamol sulphate nanoparticles can be utilized for improvement
its delivery.
Abstract: In this research work, poly (acrylonitrile-butadienestyrene)/
polypropylene (ABS/PP) blends were processed by melt
compounding in a twin-screw extruder. Upgrading of the thermal
characteristics of the obtained materials was attempted by the
incorporation of organically modified montmorillonite (OMMT), as
well as, by the addition of two types of compatibilizers;
polypropylene grafted with maleic anhydride (PP-g-MAH) and ABS
grafted with maleic anhydride (ABS-g-MAH). The effect of the
above treatments was investigated separately and in combination.
Increasing the PP content in ABS matrix seems to increase the
thermal stability of their blend and the glass transition temperature
(Tg) of SAN phase of ABS. From the other part, the addition of ABS
to PP promotes the formation of its β-phase, which is maximum at 30
wt% ABS concentration, and increases the crystallization temperature
(Tc) of PP. In addition, it increases the crystallization rate of PP.The
β-phase of PP in ABS/PP blends is reduced by the addition of
compatibilizers or/and organoclay reinforcement. The incorporation
of compatibilizers increases the thermal stability of PP and reduces
its melting (ΔΗm) and crystallization (ΔΗc) enthalpies. Furthermore it
decreases slightly the Tgs of PP and SAN phases of ABS/PP blends.
Regarding the storage modulus of the ABS/PP blends, it presents a
change in their behavior at about 10°C and return to their initial
behavior at ~110°C. The incorporation of OMMT to no compatibilized
and compatibilized ABS/PP blends enhances their storage modulus.
Abstract: Polymer melt compressibility and mold surface roughness, which are generally ignored during the filling stage of the conventional injection molding, may become increasingly significant in micro injection molding where the parts become smaller. By employing the 2.5D generalized Hele-Shaw model, we presented here the effects of polymer compressibility and mold surface roughness on mold-filling in a micro-thickness cavity. To elucidate the effects of surface roughness, numerical investigations were conducted using a cavity flat plate which has two halves with different surface roughness. This allows the comparison of flow field on two different halves under identical processing conditions but with different roughness. Results show that polymer compressibility and mold surface roughness have effects on mold filling in micro injection molding. There is in shrinkage reduction as the density is increased due to polymer melt compressibility during the filling stage.
Abstract: Legionella pneumophila is involved in more than 95%
cases of severe atypical pneumonia. Infection is mainly by
inhalation the indoor aerosols through the water-coolant systems.
Because some Legionella strains may be viable but not culturable,
therefore, Taq polymerase, DNA amplification and semi-nested-PCR
were carried out to detect Legionella-specific 16S-rDNA sequence.
For this purpose, 1.5 litter of water samples from 77 water-coolant
system were collected from four different hospitals, two nursing
homes and one student hostel in Kerman city of Iran, each in a brand
new plastic bottle during summer season of 2006 (from April to
August). The samples were filtered in the sterile condition through
the Millipore Membrane Filter. DNA was extracted from membrane
and used for PCR to detect Legionella spp. The PCR product was
then subjected to semi-nested PCR for detection of L. pneumophila.
Out of 77 water samples that were tested by PCR, 30 (39%) were
positive for most species of Legionella. However, L. pneumophila
was detected from 14 (18.2%) water samples by semi-nested PCR.
From the above results it can be concluded that water coolant
systems of different hospitals and nursing homes in Kerman city of
Iran are highly contaminated with L. pneumophila spp. and pose
serious concern. So, we recommend avoiding such type of coolant
system in the hospitals and nursing homes.