Abstract: Materials used on exterior spacecraft surfaces are subjected to many environmental threats which can cause degradation, atomic oxygen is one of the most threats. We prepared organic silicon atomic-oxygen-protection film using method of polymerization. This paper presented the effects on the film structure and its durability of the preparation processing, and analyzed the polymerization theory, the film structure and composition of the film. At last, we tested the film in our ground based atomic oxygen simulator, and indicated that the film worked well.
Abstract: The ε4 allele of the ε2, ε3 and ε4 protein isoform polymorphism in the gene encoding apolipoprotein E (Apo E) has previously been associated with increased cardiac artery disease (CAD); therefore to investigate the significance of this polymorphism in pathogenesis of CAD in Iranian patients with stenosis and control subjects. To investigate the association between
Apo E polymorphism and coronary artery disease we performed a comparative case control study of the frequency of Apo E
polymorphism in One hundred CAD patients with stenosis who underwent coronary angiography (>50% stenosis) and 100 control subjects (
Abstract: Starch/chitosan blend have been prepared via the
solution casting technique. Ionic conductivity for the system was
conducted over a wide range of frequency between 50 Hz-1 MHz and
at temperatures between 303 K and 373 K. Sample with 35 wt% of
NH4NO3 shows the highest conductivity of 3.89 ± 0.79 x 10-5 Scm-1
at room temperature. Conductivity-temperature relationship suggests
that samples are Arrhenian. Power law exponent was obtained
through dielectric loss variation and the trend suggests that the
conduction mechanism of the ions can be represented by the
correlated barrier hopping (CBH) model.
Abstract: We present an integration approach of a CMOS biosensor into a polymer based microfluidic environment suitable for mass production. It consists of a wafer-level-package for the silicon die and laser bonding process promoted by an intermediate hot melt foil to attach the sensor package to the microfluidic chip, without the need for dispensing of glues or underfiller. A very good condition of the sensing area was obtained after introducing a protection layer during packaging. A microfluidic flow cell was fabricated and shown to withstand pressures up to Δp = 780 kPa without leakage. The employed biosensors were electrically characterized in a dry environment.
Abstract: The use of synthetic retardants in polymeric insulated
cables is not uncommon in the high voltage engineering to study
electrical treeing phenomenon. However few studies on organic
materials for the same investigation have been carried. .This paper
describes the study on the effects of Oil Palm Empty Fruit Bunch
(OPEFB) microfiller on the tree initiation and propagation in silicone
rubber with different weight percentages (wt %) of filler to insulation
bulk material. The weight percentages used were 0 wt % and 1 wt %
respectively. It was found that the OPEFB retards the propagation of
the electrical treeing development. For tree inception study, the
addition of 1(wt %) OPEFB has increase the tree inception voltage of
silicone rubber. So, OPEFB is a potential retardant to the initiation
and growth of electrical treeing occurring in polymeric materials for
high voltage application. However more studies on the effects of
physical and electrical properties of OPEFB as a tree retardant
material are required.
Abstract: The effect of cross linking of the protein isolates of
three legumes with the microbial enzyme transglutaminase (EC
2.3.2.13) on the functional properties at different NaCl concentration
was studied. The reduction in the total free amino groups (OD340) of
the polymerized protein showed that TGase treatment cross-linking
the protein subunit of each legume. The solubility of the protein
polymer of each legume was greatly improved at high concentration
of NaCl. At 1.2 M NaCl the solubility of the native legumes protein
was significantly decreased but after polymerization slightly
improved. Cross linked proteins were less turbid on heating to higher
temperature as compared to native proteins and the temperature at
which the protein turns turbid also increased in the polymerized
proteins. The emulsifying and foaming properties of the protein
polymer were greatly improved at all concentrations of NaCl for all
legumes.
Abstract: This paper describes the application of a model
predictive controller to the problem of batch reactor temperature
control. Although a great deal of work has been done to improve
reactor throughput using batch sequence control, the control of the
actual reactor temperature remains a difficult problem for many
operators of these processes. Temperature control is important as
many chemical reactions are sensitive to temperature for formation of
desired products. This controller consist of two part (1) a nonlinear
control method GLC (Global Linearizing Control) to create a linear
model of system and (2) a Model predictive controller used to obtain
optimal input control sequence. The temperature of reactor is tuned
to track a predetermined temperature trajectory that applied to the
batch reactor. To do so two input signals, electrical powers and the
flow of coolant in the coil are used. Simulation results show that the
proposed controller has a remarkable performance for tracking
reference trajectory while at the same time it is robust against noise
imposed to system output.
Abstract: Polymerase chain reaction (PCR) assay and
conventional microbiological methods were used to detect bacterial
contamination of egg shells and egg content in different commercial
housing systems, open house system and evaporative cooling system.
A PCR assay was developed for direct detection using a set of
primers specific for the invasion by A gene (invA) of Salmonella spp.
PCR detected the presence of Salmonella in 2 samples of shell egg
from the evaporative cooling system, while conventional cultural
methods detected no Salmonella from the same samples.
Abstract: Polymer-like organic thin films were deposited on both
aluminum alloy type 6061 and glass substrates at room temperature by
Plasma Enhanced Chemical Vapor Deposition (PECVD) methodusing
benzene and hexamethyldisiloxane (HMDSO) as precursor materials.
The surface and physical properties of plasma-polymerized organic
thin films were investigated at different r.f. powers. The effects of
benzene/argon ratio on the properties of plasma polymerized benzene
films were also investigated. It is found that using benzene alone
results in a non-coherent and non-adherent powdery deposited
material. The chemical structure and surface properties of the asgrown
plasma polymerized thin films were analyzed on glass
substrates with FTIR and contact angle measurements. FTIR spectra
of benzene deposited film indicated that the benzene rings are
preserved when increasing benzene ratio and/or decreasing r.f.
powers. FTIR spectra of HMDSO deposited films indicated an
increase of the hydrogen concentration and a decrease of the oxygen
concentration with the increase of r.f. power. The contact angle (θ) of
the films prepared from benzene was found to increase by about 43%
as benzene ratio increases from 10% to 20%. θ was then found to
decrease to the original value (51°) when the benzene ratio increases
to 100%. The contact angle, θ, for both benzene and HMDSO
deposited films were found to increase with r.f. power. This signifies
that the plasma polymerized organic films have substantially low
surface energy as the r.f power increases. The corrosion resistance of
aluminum alloy substrate both bare and covered with plasma
polymerized thin films was carried out by potentiodynamic
polarization measurements in standard 3.5 wt. % NaCl solution at
room temperature. The results indicate that the benzene and HMDSO
deposited films are suitable for protection of the aluminum substrate
against corrosion. The changes in the processing parameters seem to
have a strong influence on the film protective ability. Surface
roughness of films deposited on aluminum alloy substrate was
investigated using scanning electron microscopy (SEM). The SEM
images indicate that the surface roughness of benzene deposited films
increase with decreasing the benzene ratio. SEM images of benzene
and HMDSO deposited films indicate that the surface roughness
decreases with increasing r.f. power. Studying the above parameters
indicate that the films produced are suitable for specific practical
applications.
Abstract: Novel polystrene-bound Schiff bases and their Pt(IV)
complexes have been prepared from condensation reaction of
polystyrene-A-NH2 with 2-hydroxybenzaldehyde and 5-fluoro-3-
bromo-2-hydroxybenzaldehyde. The structures of Pt(IV) complexes
with polystyrene including Schiff bases have been determined by
elemental analyses, magnetic susceptibility, IR, 1H-NMR, UV-vis,
TG/DTA and AAS. The antibacterial and antifungal activities of the
synthesized compounds have been studied by the well-diffusion
method against some selected microorganisms: (Bacillus cereus spp.,
Listeria monocytogenes 4b, Micrococcus luteus, Staphylococcus
aureus, Staphylococcus epidermis, Brucella abortus, Escherichia
coli, Pseudomonas putida spp., Shigella dysenteria type 10,
Salmonella typhi H).
Abstract: this study was carried out to investigate the changes in
quality parameters of rye bread packaged in different polymer films
during convection air-flow thermal treatment process. Whole loafs of
bread were placed in polymer pouches, which were sealed in reduced
pressure air ambiance, bread was thermally treated in
at temperature +(130; 140; and 150) ± 5 ºC within 40min, as long as
the core temperature of the samples have reached accordingly
+80±1 ºC. For bread packaging pouches were used: anti-fog
Mylar®OL12AF and thermo resistant combined polymer material.
Main quality parameters was analysed using standard methods:
temperature in bread core, bread crumb and crust firmness value,
starch granules volume and microflora. In the current research it was
proved, that polymer films significantly influence rye bread quality
parameters changes during thermal treatment. Thermo resistant
combined polymer material film could be recommendable for
packaged rye bread pasteurization, for maximal bread quality
parameter keeping.
Abstract: The simulation of extrusion process is studied widely
in order to both increase products and improve quality, with broad
application in wire coating. The annular tube-tooling extrusion was
set up by a model that is termed as Navier-Stokes equation in
addition to a rheological model of differential form based on singlemode
exponential Phan-Thien/Tanner constitutive equation in a twodimensional
cylindrical coordinate system for predicting the
contraction point of the polymer melt beyond the die. Numerical
solutions are sought through semi-implicit Taylor-Galerkin pressurecorrection
finite element scheme. The investigation was focused on
incompressible creeping flow with long relaxation time in terms of
Weissenberg numbers up to 200. The isothermal case was considered
with surface tension effect on free surface in extrudate flow and no
slip at die wall. The Stream Line Upwind Petrov-Galerkin has been
proposed to stabilize solution. The structure of mesh after die exit
was adjusted following prediction of both top and bottom free
surfaces so as to keep the location of contraction point around one
unit length which is close to experimental results. The simulation of
extrusion process is studied widely in order to both increase products
and improve quality, with broad application in wire coating. The
annular tube-tooling extrusion was set up by a model that is termed
as Navier-Stokes equation in addition to a rheological model of
differential form based on single-mode exponential Phan-
Thien/Tanner constitutive equation in a two-dimensional cylindrical
coordinate system for predicting the contraction point of the polymer
melt beyond the die. Numerical solutions are sought through semiimplicit
Taylor-Galerkin pressure-correction finite element scheme.
The investigation was focused on incompressible creeping flow with
long relaxation time in terms of Weissenberg numbers up to 200. The
isothermal case was considered with surface tension effect on free
surface in extrudate flow and no slip at die wall. The Stream Line
Upwind Petrov-Galerkin has been proposed to stabilize solution. The
structure of mesh after die exit was adjusted following prediction of
both top and bottom free surfaces so as to keep the location of
contraction point around one unit length which is close to
experimental results.
Abstract: This paper has examined the energy consumption characteristics in six different buildings including apartments, offices, commercial buildings, hospitals, hotels and educational facilities. Then 5-hectare (50000m2) development site for respective building-s type has been assumed as case study to evaluate the introduction effect of Combined Heat and Power (CHP). All kinds of CHP systems with different distributed generation technologies including Gas Turbine (GT), Gas Engine (GE), Diesel Engine (DE), Solid Oxide Fuel Cell (SOFC) and Polymer Electrolyte Fuel Cell (PEFC), have been simulated by using HEATMAP, CHP system analysis software. And their primary energy utilization efficiency, energy saving ratio and CO2 reduction ratio have evaluated and compared respectively. The results can be summarized as follows: Various buildings have their special heat to power ratio characteristics. Matching the heat to power ratio demanded from an individual building with that supplied from a CHP system is very important. It is necessary to select a reasonable distributed generation technologies according to the load characteristics of various buildings. Distributed generation technologies with high energy generating efficiency and low heat to power ratio, like SOFC and PEFC is more reasonable selection for Building Combined Heat and Power (BCHP). CHP system is an attractive option for hotels, hospitals and apartments in Japan. The users can achieve high energy saving and environmental benefit by introducing a CHP systems. In others buildings, especially like commercial buildings and offices, the introduction of CHP system is unreasonable.
Abstract: To produce sugar and ethanol, sugarcane processing
generates several agricultural residues, being straw and bagasse is
considered as the main among them. And what to do with this
residues has been subject of many studies and experiences in an
industry that, in recent years, highlighted by the ability to transform
waste into valuable products such as electric power. Cellulose is the
main component of these materials. It is the most common organic
polymer and represents about 1.5 x 1012 tons of total production of
biomass per year and is considered an almost inexhaustible source of
raw material. Pretreatment with mineral acids is one of the most
widely used as stage of cellulose extraction from lignocellulosic
materials for solubilizing most of the hemicellulose content. This
study had as goal to find the best reaction time of sugarcane bagasse
pretreatment with sulfuric acid in order to minimize the losses of
cellulose concomitantly with the highest possible removal of
hemicellulose and lignin. It was found that the best time for this
reaction was 40 minutes, in which it was reached a loss of
hemicelluloses around 70% and lignin and cellulose, around 15%.
Over this time, it was verified that the cellulose loss increased and
there was no loss of lignin and hemicellulose.
Abstract: The pigments covered by film-forming polymers have
opened a prospect to improve the quality of water-based printing
inks. In this study such pigments were prepared by the initiated
polymerization of styrene and methacrylate derivative monomers in
the aqueous pigment dispersions. The formation of polymer films
covering pigment cores depends on the polymerization time and the
ratio of pigment to monomers. At the time of 4 hours and the ratio of
1/10 almost pigment particles are coated by the polymer. The formed
polymer covers of pigments have the average thickness of 5.95 nm.
The size increasing percentage of the coated particles after a week is
4.5 %, about fourteen-fold lower than of the original ones. The
obtained results indicate that the coated pigments are improved
dispersion stability in water medium along with a guarantee for the
optical colour.
Abstract: In this article, we synthesize a novel chitosan -based
superabsorbent hydrogel via graft copolymerization of mixtures
acrylic acid (AA) and N-vinyl pyrollidon onto chitosan backbones.
The polymerization reaction was carried out in an aqueous medium
and in the presence of ammonium persulfate (APS) as an initiator and
N,N'-methylene bisacrylamide (MBA) as a crosslinker.The hydrogel
structures were confirmed by FTIR spectroscopy. The swelling
behavior of these absorbent polymers was also investigated in
various salt solutions. Results indicated that the swelling capacity
decreased with an increase in the ionic strength of the swelling
medium. Furthermore, the swelling of superabsorbing hydrogels was
examined in solutions with pH values ranging between 1.0 and 13.0.
It showed a reversible pH-responsive behavior at pHs 2.0 and 8.0.
This on-off switching behavior makes the synthesized hydrogels as
an excellent candidate for controlled delivery of bioactive agents.
Abstract: Carbon fibers have specific characteristics in
comparison with industrial and structural materials used in different
applications. Special properties of carbon fibers make them attractive
for reinforcing and fabrication of composites. These fibers have been
utilized for composites of metals, ceramics and plastics. However,
it-s mainly used in different forms to reinforce lightweight polymer
materials such as epoxy resin, polyesters or polyamides. The
composites of carbon fiber are stronger than steel, stiffer than
titanium, and lighter than aluminum and nowadays they are used in a
variety of applications. This study explains applications of carbon
fibers in different fields such as space, aviation, transportation,
medical, construction, energy, sporting goods, electronics, and the
other commercial/industrial applications. The last findings of
composites with polymer, metal and ceramic matrices containing
carbon fibers and their applications in the world investigated.
Researches show that carbon fibers-reinforced composites due to
unique properties (including high specific strength and specific
modulus, low thermal expansion coefficient, high fatigue strength,
and high thermal stability) can be replaced with common industrial
and structural materials.
Abstract: The present study was performed in Musa bay (northern part of the Persian Gulf) around the coastal area of Bandare-Imam Khomeini and Razi Petrochemical Companies. Sediment samples and effluent samples were collected from the selected stations, from June 2009 to June 2010. The samples were analyzed to determine the degree of hydrocarbon contamination. The average level of TPH concentration in the study area was more than the natural background value at all of the stations, especially at station BI1 which was the main effluent outlet of Bandar-e- Imam Khomeini petrochemical company. Also the concentration of total petroleum hydrocarbon was monitored in the effluents of aforementioned petrochemical companies and the results showed that the concentration of TPH in the effluents of Bandar-e- Imam Khomeini petrochemical company was greater than Razi petrochemical company which is may be related to the products of Bandar-e- Imam Khomeini petrochemical company (aromatics, polymers, chemicals, fuel).
Abstract: The effect of gamma irradiation on micro-hardness of polymer blends of poly (ethyl methacrylate)(PEMA) and poly (ethylene oxide) (PEO) has been investigated to detect the radiation induced crosslinking. The blend system comprises a noncrystallizable polymer, PEMA and a crystallizable polymer, PEO. On irradiation, the overall hardness of the blend specimens for different dose levels infers occurrence of a crosslinking process. The radiation-induced crosslinking was greater for blends having lower concentration of PEO. However, increase in radiation dose causes softening of blend system due to radiation induced scissioning of the chains
Abstract: This study deals with the experimental investigation
and theoretical modeling of Semi crystalline polymeric materials with
a rubbery amorphous phase (HDPE) subjected to a uniaxial cyclic
tests with various maximum strain levels, even at large deformation.
Each cycle is loaded in tension up to certain maximum strain and
then unloaded down to zero stress with N number of cycles. This
work is focuses on the measure of the volume strain due to the
phenomena of damage during this kind of tests. On the basis of
thermodynamics of relaxation processes, a constitutive model for
large strain deformation has been developed, taking into account the
damage effect, to predict the complex elasto-viscoelastic-viscoplastic
behavior of material. A direct comparison between the model
predictions and the experimental data show that the model accurately
captures the material response. The model is also capable of
predicting the influence damage causing volume variation.