Abstract: This paper presents the experimental results of silicone rubber polymer insulators for 22 kV systems under salt water dip wheel test based on IEC 62217. Straight shed silicone rubber polymer insulators having leakage distance 685 mm were tested continuously 30,000 cycles. One test cycle includes 4 positions, energized, de-energized, salt water dip and deenergized, respectively. For one test cycle, each test specimen remains stationary for about 40 second in each position and takes 8 second for rotate to next position. By visual observation, sever surface erosion was observed on the trunk near the energized end of tested specimen. Puncture was observed on the upper shed near the energized end. In addition, decreasing in hydrophobicity and increasing in hardness were measured on tested specimen comparing with new specimen. Furthermore, chemical analysis by ATR-FTIR was conducted in order to elucidate the chemical change of tested specimens comparing with new specimen.
Abstract: In an assessment of the extractability of metals in
green liquor dregs from the chemical recovery circuit of semichemical
pulp mill, extractable concentrations of heavy metals in
artificial gastric fluid were between 10 (Ni) and 717 (Zn) times
higher than those in artificial sweat fluid. Only Al (6.7 mg/kg; d.w.),
Ni (1.2 mg/kg; d.w.) and Zn (1.8 mg/kg; d.w.) showed extractability
in the artificial sweat fluid, whereas Al (730 mg/kg; d.w.), Ba (770
mg/kg; d.w.) and Zn (1290 mg/kg; d.w.) showed clear extractability
in the artificial gastric fluid. As certain heavy metals were clearly
soluble in the artificial gastric fluid, the careful handling of this
residue is recommended in order to prevent the penetration of green
liquor dregs across the human gastrointestinal tract.
Abstract: The main aim of this research is to study the possible
use of recycled fine aggregate made from waste rubble wall to
substitute partially for the natural sand used in the production of
cement and sand bricks. The bricks specimens were prepared by
using 100% natural sand; they were then replaced by recycled fine
aggregate at 25, 50, 75, and 100% by weight of natural sand. A series
of tests was carried out to study the effect of using recycled aggregate
on the physical and mechanical properties of bricks, such as density,
drying shrinkage, water absorption characteristic, compressive and
flexural strength. Test results indicate that it is possible to
manufacture bricks containing recycled fine aggregate with good
characteristics that are similar in physical and mechanical properties
to those of bricks with natural aggregate, provided that the percentage
of recycled fine aggregates is limited up to 50-75%.
Abstract: Basic objective of this study is to create a regression
analysis method that can estimate the length of a plastic hinge which
is an important design parameter, by making use of the outcomes of
(lateral load-lateral displacement hysteretic curves) the experimental
studies conducted for the reinforced square concrete columns. For
this aim, 170 different square reinforced concrete column tests results
have been collected from the existing literature. The parameters
which are thought affecting the plastic hinge length such as crosssection
properties, features of material used, axial loading level,
confinement of the column, longitudinal reinforcement bars in the
columns etc. have been obtained from these 170 different square
reinforced concrete column tests. In the study, when determining the
length of plastic hinge, using the experimental test results, a
regression analysis have been separately tested and compared with
each other. In addition, the outcome of mentioned methods on
determination of plastic hinge length of the reinforced concrete
columns has been compared to other methods available in the
literature.
Abstract: We have developed a microfluidic device system for the continuous producting of nanoparticles, and we have clarified the relationship between the mixing performance of reactors and the particle size. First, we evaluated the mixing performance of reactors by carring out the Villermaux–Dushman reaction and determined the experimental conditions for producing AgCl nanoparticles. Next, we produced AgCl nanoparticles and evaluated the mixing performance and the particle size. We found that as the mixing performance improves the size of produced particles decreases and the particle size distribution becomes sharper. We produced AgCl nanoparticles with a size of 86 nm using the microfluidic device that had the best mixing performance among the three reactors we tested in this study; the coefficient of variation (Cv) of the size distribution of the produced nanoparticles was 26.1%.
Abstract: The purpose of research was to know the role of
immunogenic protein of 49 kDa from V.alginolyticus which capable
to initiate molecule expression of MHC Class II in receptor of
Cromileptes altivelis. The method used was in vivo experimental
research through testing of immunogenic protein 49 kDa from
V.alginolyticus at Cromileptes altivelis (size of 250 - 300 grams)
using 3 times booster by injecting an immunogenic protein in a
intramuscular manner. Response of expressed MHC molecule was
shown using immunocytochemistry method and SEM. Results
indicated that adhesin V.alginolyticus 49 kDa which have
immunogenic character could trigger expression of MHC class II on
receptor of grouper and has been proven by staining using
immunocytochemistry and SEM with labeling using antibody anti
MHC (anti mouse). This visible expression based on binding between
epitopes antigen and antibody anti MHC in the receptor. Using
immunocytochemistry, intracellular response of MHC to in vivo
induction of immunogenic adhesin from V.alginolyticus was shown.
Abstract: In most of the cases, natural disasters lead to the
necessity of evacuating people. The quality of evacuation
management is dramatically improved by the use of information
provided by decision support systems, which become indispensable
in case of large scale evacuation operations. This paper presents a
best practice case study. In November 2007, officers from the
Emergency Situations Inspectorate “Crisana" of Bihor County from
Romania participated to a cross-border evacuation exercise, when
700 people have been evacuated from Netherlands to Belgium. One
of the main objectives of the exercise was the test of four different
decision support systems. Afterwards, based on that experience,
software system called TEVAC (Trans Border Evacuation) has been
developed “in house" by the experts of this institution. This original
software system was successfully tested in September 2008, during
the deployment of the international exercise EU-HUROMEX 2008,
the scenario involving real evacuation of 200 persons from Hungary
to Romania. Based on the lessons learned and results, starting from
April 2009, the TEVAC software is used by all Emergency
Situations Inspectorates all over Romania.
Abstract: Day by day technology increases and problems
associated with this technology also increase. Several researches
were carried out to investigate the deployment of such material safely
in geotechnical engineering in particular and civil engineering in
general. However, different types of waste material have such as
cement duct, fly ash and slag been proven to be suitable in several
applications. In this research cement dust mixed with different
percentages of sand will be used in some civil engineering
application as will be explained later in this paper throughout filed
and laboratory test. The used mixer (waste material with sand) prove
high performance, durability to environmental condition, low cost
and high benefits. At higher cement dust ratio, small cement ratio is
valuable for compressive strength and permeability. Also at small
cement dust ratio higher cement ratio is valuable for compressive
strength.
Abstract: Artifact rejection plays a key role in many signal processing applications. The artifacts are disturbance that can occur during the signal acquisition and that can alter the analysis of the signals themselves. Our aim is to automatically remove the artifacts, in particular from the Electroencephalographic (EEG) recordings. A technique for the automatic artifact rejection, based on the Independent Component Analysis (ICA) for the artifact extraction and on some high order statistics such as kurtosis and Shannon-s entropy, was proposed some years ago in literature. In this paper we try to enhance this technique proposing a new method based on the Renyi-s entropy. The performance of our method was tested and compared to the performance of the method in literature and the former proved to outperform the latter.
Abstract: The purpose of this study was to develop a “teachers’
self-efficacy scale for high school physical education teachers
(TSES-HSPET)” in Taiwan. This scale is based on the self-efficacy
theory of Bandura [1], [2]. This study used exploratory and
confirmatory factor analyses to test the reliability and validity. The
participants were high school physical education teachers in Taiwan.
Both stratified random sampling and cluster sampling were used to
sample participants for the study. 350 teachers were sampled in the
first stage and 234 valid scales (male 133, female 101) returned.
During the second stage, 350 teachers were sampled and 257 valid
scales (male 143, female 110, 4 did not indicate gender) returned. The
exploratory factor analysis was used in the first stage, and it got
60.77% of total variance for construct validity. The Cronbach’s alpha
coefficient of internal consistency was 0.91 for sumscale, and
subscales were 0.84 and 0.90. In the second stage, confirmatory factor
analysis was used to test construct validity. The result showed that the
fit index could be accepted (χ2 (75) =167.94, p
Abstract: This investigation examines the effect of the sintering
temperature curve in manufactured nickel powder capillary structure
(wick) for a loop heat pipe (LHP). The sintering temperature curve is
composed of a region of increasing temperature; a region of constant
temperature and a region of declining temperature. The most important
region is that in which the temperature increases, as an index in the
stage in which the temperature increases. The wick of nickel powder is
manufactured in the stage of fixed sintering temperature and the time
between the stage of constant temperature and the stage of falling
temperature. When the slope of the curve in the region of increasing
temperature is unity (equivalent to 10 °C/min), the structure of the
wick is complete and the heat transfer performance is optimal. The
result of experiment test demonstrates that the heat transfer
performance is optimal at 320W; the minimal total thermal resistance
is approximately 0.18°C/W, and the heat flux is 17W/cm2; the internal
parameters of the wick are an effective pore radius of 3.1 μm, a
permeability of 3.25×10-13m2 and a porosity of 71%.
Abstract: With Power system movement toward restructuring along with factors such as life environment pollution, problems of transmission expansion and with advancement in construction technology of small generation units, it is expected that small units like wind turbines, fuel cells, photovoltaic, ... that most of the time connect to the distribution networks play a very essential role in electric power industry. With increase in developing usage of small generation units, management of distribution networks should be reviewed. The target of this paper is to present a new method for optimal management of active and reactive power in distribution networks with regard to costs pertaining to various types of dispersed generations, capacitors and cost of electric energy achieved from network. In other words, in this method it-s endeavored to select optimal sources of active and reactive power generation and controlling equipments such as dispersed generations, capacitors, under load tapchanger transformers and substations in a way that firstly costs in relation to them are minimized and secondly technical and physical constraints are regarded. Because the optimal management of distribution networks is an optimization problem with continuous and discrete variables, the new evolutionary method based on Ant Colony Algorithm has been applied. The simulation results of the method tested on two cases containing 23 and 34 buses exist and will be shown at later sections.
Abstract: As days go by, we hear more and more about HIV,
Ebola, Bird Flu and other dreadful viruses which were unknown a
few decades ago. In both detecting and fighting viral diseases
ordinary methods have come across some basic and important
difficulties. Vaccination is by a sense introduction of the virus to the
immune system before the occurrence of the real case infection. It is
very successful against some viruses (e.g. Poliomyelitis), while
totally ineffective against some others (e.g. HIV or Hepatitis-C). On
the other hand, Anti-virus drugs are mostly some tools to control and
not to cure a viral disease. This could be a good motivation to try
alternative treatments. In this study, some key features of possible
physical-based alternative treatments for viral diseases are presented.
Electrification of body parts or fluids (especially blood) with micro
electric signals with adjusted current or frequency is also studied. The
main approach of this study is to find a suitable energy field, with
appropriate parameters that are able to kill or deactivate viruses. This
would be a lengthy, multi-disciplinary research which needs the
contribution of virology, physics, and signal processing experts. It
should be mentioned that all the claims made by alternative cures
researchers must be tested carefully and are not advisable at the time
being.
Abstract: Most CT reconstruction system x-ray computed
tomography (CT) is a well established visualization technique in
medicine and nondestructive testing. However, since CT scanning
requires sampling of radiographic projections from different viewing
angles, common CT systems with mechanically moving parts are too
slow for dynamic imaging, for instance of multiphase flows or live
animals. A large number of X-ray projections are needed to
reconstruct CT images, so the collection and calculation of the
projection data consume too much time and harmful for patient. For
the purpose of solving the problem, in this study, we proposed a
method for tomographic reconstruction of a sample from a limited
number of x-ray projections by using linear interpolation method. In
simulation, we presented reconstruction from an experimental x-ray
CT scan of a Aluminum phantom that follows to two steps: X-ray
projections will be interpolated using linear interpolation method and
using it for CT reconstruction based upon Ordered Subsets
Expectation Maximization (OSEM) method.
Abstract: A 3D industrial computed tomography (CT)
manufactured based on a first generation CT systems, single-source
– single-detector, was evaluated. Operation accuracy assessment of
the manufactured system was achieved using simulation in
comparison with experimental tests. 137Cs and 60Co were used as a gamma source. Simulations were achieved using MCNP4C code.
Experimental tests of 137Cs were in good agreement with the simulations
Abstract: This paper describes a novel projection algorithm, the Projection Onto Span Algorithm (POSA) for wavelet-based superresolution and removing speckle (in wavelet domain) of unknown variance from Synthetic Aperture Radar (SAR) images. Although the POSA is good as a new superresolution algorithm for image enhancement, image metrology and biometric identification, here one will use it like a tool of despeckling, being the first time that an algorithm of super-resolution is used for despeckling of SAR images. Specifically, the speckled SAR image is decomposed into wavelet subbands; POSA is applied to the high subbands, and reconstruct a SAR image from the modified detail coefficients. Experimental results demonstrate that the new method compares favorably to several other despeckling methods on test SAR images.
Abstract: Trihalomethanes (THMs) were among the first
disinfection byproducts to be discovered in chlorinated water. The
substances form during a reaction between chlorine and organic
matter in the water. Trihalomethanes are suspected to have negative
effects on birth such as, low birth weight, intrauterine growth
retardation in term births, as well as gestational age and preterm
delivery. There are also some evidences showing these by-products to
be mutagenic and carcinogenic, the greatest amount of evidence being
related to the bladder cancer. However, there exist inconsistencies
regarding such effects of THMs as different studies have provided
different results in this regard. The aim of the present study is to
provide a review of the related researches about the above mentioned
health effects of THMs.
Abstract: This work presents a new phonetic transcription system based on a tree of hierarchical pronunciation rules expressed as context-specific grapheme-phoneme correspondences. The tree is automatically inferred from a phonetic dictionary by incrementally analyzing deeper context levels, eventually representing a minimum set of exhaustive rules that pronounce without errors all the words in the training dictionary and that can be applied to out-of-vocabulary words. The proposed approach improves upon existing rule-tree-based techniques in that it makes use of graphemes, rather than letters, as elementary orthographic units. A new linear algorithm for the segmentation of a word in graphemes is introduced to enable outof- vocabulary grapheme-based phonetic transcription. Exhaustive rule trees provide a canonical representation of the pronunciation rules of a language that can be used not only to pronounce out-of-vocabulary words, but also to analyze and compare the pronunciation rules inferred from different dictionaries. The proposed approach has been implemented in C and tested on Oxford British English and Basic English. Experimental results show that grapheme-based rule trees represent phonetically sound rules and provide better performance than letter-based rule trees.
Abstract: Snake bite cases in Malaysia most often involve the
species Naja-naja and Calloselasma rhodostoma. In keeping with the
need for a rapid snake venom detection kit in a clinical setting, plate
and dot-ELISA test for the venoms of Naja-naja sumatrana,
Calloselasma rhodostoma and the cobra venom fraction V antigen
was developed. Polyclonal antibodies were raised and further used to
prepare the reagents for the dot-ELISA test kit which was tested in
mice, rabbit and virtual human models. The newly developed dot-
ELISA kit was able to detect a minimum venom concentration of
244ng/ml with cross reactivity of one antibody type. The dot-ELISA
system was sensitive and specific for all three snake venom types in
all tested animal models. The lowest minimum venom concentration
detectable was in the rabbit model, 244ng/ml of the cobra venom
fraction V antigen. The highest minimum venom concentration was
in mice, 1953ng/ml against a multitude of venoms. The developed
dot-ELISA system for the detection of three snake venom types was
successful with a sensitivity of 95.8% and specificity of 97.9%.
Abstract: The objective of the presented work is to implement the Kalman Filter into an application that reduces the influence of the environmental changes over the robot expected to navigate over a terrain of varying friction properties. The Discrete Kalman Filter is used to estimate the robot position, project the estimated current state ahead at time through time update and adjust the projected estimated state by an actual measurement at that time via the measurement update using the data coming from the infrared sensors, ultrasonic sensors and the visual sensor respectively. The navigation test has been performed in a real world environment and has been found to be robust.