Abstract: This study is aiming at establishing the relationship
between the optical signal of flame and an equivalent ratio of flame. In
this experiment, flame optical signal in a furnace is measured using
photodiode. The combustion system is composed of metal fiber burner
and vertical furnace, and flame chemiluminescence is measured at
various experimental conditions. In this study, the flame
chemiluminescence of laminar premixed flame is measured using
commercially available photodiode. It is experimentally investigated
the relationship between equivalent ratio and photodiode signal. In
addition, the strategy of combustion control method is proposed using
the optical signal and fuel pressure.
The results showed that certain relationship between optical data of
photodiode and equivalence ratio exists, and this leads to the
successful application of this system for instantaneous measurement of
equivalence ration of the combustion system.
Abstract: Development of new generation bio-tribological,
multilayer coatings opens an avenue for fabrication of future hightech
functional surfaces. In the presented work, nano-composite,
Cr/CrN+[Cr/ a-C:H implanted by metallic nanocrystals] multilayer
coatings have been developed for surface protection of medical tools.
Thin films were fabricated by a hybrid Pulsed Laser Deposition
technique. Complex microstructure analysis of nanomultilayer
coatings, subjected to mechanical and biological tests, were
performed by means of transmission electron microscopy (TEM).
Microstructure characterization revealed the layered arrangement of
Cr23C6 nanoparticles in multilayer structure. Influence of deposition
conditions on bio-tribological properties of the coatings was studied.
The bio-tests were used as a screening tool for the analyzed
nanomultilayer coatings before they could be deposited on medical
tools. Bio-medical tests were done using fibroblasts. The mechanical
properties of the coatings were investigated by means of a ball-ondisc
mechanical test. The micro hardness was done using Berkovich
indenter. The scratch adhesion test was done using Rockwell
indenter. From the bio-tribological point of view, the optimal
properties had the C106_1 material.
Abstract: WO3/SiO2 catalysts were modified by an ion exchange
method with sodium hydroxide or potassium hydroxide solution. The
performance of the modified catalysts was tested in the metathesis of
ethylene and trans-2-butene to propylene. During ion exchange,
sodium and potassium ions played different roles. Sodium modified
catalysts revealed constant trans-2-butene conversion and propylene
selectivity when the concentrations of sodium in the solution were
varied. In contrast, potassium modified catalysts showed reduction of
the conversion and increase of the selectivity. From these results,
potassium hydroxide may affect the transformation of tungsten oxide
active species, resulting in the decrease in conversion whereas
sodium hydroxide did not. Moreover, the modification of catalysts by
this method improved the catalyst stability by lowering the amount of
coke deposited on the catalyst surface.
Abstract: This study focuses on a novel method for dispersion
and distribution of reinforcement under high intensive shear stress to
produce metal composites. The polyacrylonitrile (PAN)-based short
carbon fiber (Csf) and Nextel 610 alumina fiber were dispersed under
high intensive shearing at mushy zone in semi-solid of A356 by a
novel method. The bundles and clusters were embedded by
infiltration of slurry into the clusters, thus leading to a uniform
microstructure. The fibers were embedded homogenously into the
aluminum around 576-580°C with around 46% of solid fraction.
Other experiments at 615°C and 568°C which are contained 0% and
90% solid respectively were not successful for dispersion and
infiltration of aluminum into bundles of Csf. The alumina fiber has
been cracked by high shearing load. The morphologies and
crystalline phase were evaluated by SEM and XRD. The adopted
thixo-process effectively improved the adherence and distribution of
Csf into Al that can be developed to produce various composites by
thixomixing.
Abstract: Microbes have been used to solve environmental
problems for many years. The role of microorganism to sequester,
precipitate or alter the oxidation state of various heavy metals has
been extensively studied. Treatment using microorganism interacts
with toxic metal are very diverse. The purpose of this research is to
remove the mercury using Pseudomonas putida (P. putida), pure
culture ATTC 49128 at optimum growth parameters such as
techniques of culture, acclimatization time and speed of incubator
shaker. Thus, in this study, the optimum growth parameters of P.
putida were obtained to achieve the maximum of mercury removal.
Based on the optimum parameters of P. putida for specific growth
rate, the removal of two different mercury concentration, 1 ppm and
4 ppm were studied. From mercury nitrate solution, a mercuryresistant
bacterial strain which is able to reduce from ionic mercury
to metallic mercury was used to reduce ionic mercury. The overall
levels of mercury removal in this study were between 80% and 89%.
The information obtained in this study is of fundamental for
understanding of the survival of P. putida ATTC 49128 in mercury
solution. Thus, microbial mercury removal is a potential
bioremediation for wastewater especially in petrochemical industries
in Malaysia.
Abstract: Potassium borates, which are widely used in welding
and metal refining industry, as a lubricating oil additive, cement
additive, fiberglass additive and insulation compound, are one of the
important groups of borate minerals. In this study the production of a
potassium borate mineral via hydrothermal method is aimed. The
potassium source of potassium nitrate (KNO3) was used along with a
sodium source of sodium hydroxide (NaOH) and boron source of
boric acid (H3BO3). The constant parameters of reaction temperature
and reaction time were determined as 80°C and 1 h, respectively. The
molar ratios of 1:1:3 (as KNO3:NaOH:H3BO3), 1:1:4, 1:1:5, 1:1:6
and 1:1:7 were used. Following the synthesis the identifications of
the produced products were conducted by X-Ray Diffraction (XRD),
Fourier Transform Infrared Spectroscopy (FT-IR) and Raman
Spectroscopy. The results of the experiments and analysis showed in
the ratio of 1:1:6, the Santite mineral with powder diffraction file
number (pdf no.) of 01-072-1688, which is known as potassium
pentaborate (KB5O8·4H2O) was synthesized as best.
Abstract: Electrodeposition is a simple and economic technique
for precision coating of different shaped substrates with pure metal,
alloy or composite films. Dc electrodeposition was used to produce
Cr, Co-Cr and Co-Cr/TiO2 nano-composite coatings from Cr(III)
based electrolytes onto 316L SS substrates. The effects of TiO2 nanoparticles
concentration on co-deposition of these particles along with
Cr content and microhardness of the coatings were investigated.
Morphology of the Cr, Co-Cr and Co-Cr/TiO2 coatings besides their
tribological behavior were studied. The results showed that increment
of TiO2 nanoparticles concentration from 0 to 30 g L-1 in the bath
increased their co-deposition and Cr content of the coatings from 0 to
3.5 wt.% and from 23.7 to 31.2 wt.%, respectively. Microhardness of
Cr coating was about 920 Hv which was higher than Co-Cr and even
Co-Cr/TiO2 films. Microhardness of Co-Cr and Co-Cr/TiO2 coatings
were improved by increasing their Cr and TiO2 content. All the
coatings had nodular morphology and contained microcracks.
Nodules sizes and the number of microcracks in the alloy and
composite coatings were lower than the Cr film. Wear results
revealed that the Co-Cr/TiO2 coating had the lowest wear loss
between all the samples, while the Cr film had the worst wear
resistance.
Abstract: The addition of lime as Ca(OH)2 to sewage sludge to
destroy pathogens (Escherichia coli), was evaluated also in relation
to heavy metal bioavailability.
The obtained results show that the use of calcium hydroxide at the
dose of 3% effectively destroyed pathogens ensuring the stability at
high pH values over long period and the duration of the sewage
sludge stabilization. In general, lime addition decreased the total
extractability of heavy metals indicating a reduced bioavailability of
these elements. This is particularly important for a safe utilization in
agricultural soils to reduce the possible transfer of heavy metals to
the food chain.
Abstract: Froth flotation remains to date as one of the most used
metallurgical processes for concentrating metal-bearing minerals in
ores. Oxide ores are relatively less amenable to froth flotation and
require a judicious choice of reagents for the recovery of metals to be
optimised. Laboratory batch flotation tests were conducted to
determine the effect of two types of gasoil-rinkalore mixtures on the
flotation response of a copper cobalt oxide ore sample. The head
assay conducted on the initial ore sample showed that it contained
about 2.90% of Cu, 0.12% of Co.
Upon the flotation test work, the results obtained indicated that the
concentrate obtained with use of the mixture gazoil-rinkalore RX
yielded 8.24% Cu and 0.22% Co concentrate grades with recoveries
of 76.0% Cu and 78.0% Co respectively. But, the concentrate
obtained by use of the mixture gazoil-rinkalore RX3 yielded
relatively bad results with 5.92% Cu and 0.18% Cu concentrate
grades with recoveries of 70.3% Cu and 65.3% Co respectively.
Abstract: Intermetallic materials are among advanced
technology materials that have outstanding mechanical and physical
properties for high temperature applications. Especially creep
resistance, low density and high hardness properties stand out in such
intermetallics. The microstructure, mechanical properties of %88Ni-
%10Cr and %2Mn powders were investigated using specimens
produced by tube furnace sintering at 900-1300°C temperature. A
composite consisting of ternary additions, a metallic phase, Fe, Cr
and Mn have been prepared under Ar shroud and then tube furnace
sintered. XRD, SEM (Scanning Electron Microscope), were
investigated to characterize the properties of the specimens.
Experimental results carried out for composition %88Ni-%10Cr and
%2Mn at 1300°C suggest that the best properties as 138,80HV and
6,269/cm3 density were obtained at 1300°C.
Abstract: Microstructural and electrical properties of
Cu-chromium alloy (Cu-Cr) dispersed with vapor-grown carbon fiber
(VGCF) prepared by powder metallurgy (P/M) process have been
investigated. Cu-0.7 mass% Cr pre-alloyed powder (Cu-Cr) made by
water atomization process was used as raw materials, which contained
solid solute Cr elements in Cu matrix. The alloy powder coated with
un-bundled VGCF by using oil coating process was consolidated at
1223 K in vacuum by spark plasma sintering, and then extruded at
1073 K. The extruded Cu-Cr alloy (monolithic alloy) had 209.3 MPa
YS and 80.4 IACS% conductivity. The extruded Cu-Cr with 0.1
mass% VGCF composites revealed a small decrease of YS compared
to the monolithic Cu-Cr alloy. On the other hand, the composite had a
higher electrical conductivity than that of the monolithic alloy. For
example, Cu-Cr with 0.1 mass% VGCF composite sintered for 5 h
showed 182.7 MPa YS and 89.7 IACS% conductivity. In the case of
Cu-Cr with VGCFs composites, the Cr concentration was observed
around VGCF by SEM-EDS analysis, where Cr23C6 compounds were
detected by TEM observation. The amount of Cr solid solution in the
matrix of the Cu-Cr composites alloy was about 50% compared to the
monolithic Cu-Cr sintered alloy, and resulted in the remarkable
increment of the electrical conductivity.
Abstract: The aim of this study is to investigate formability of
Al based closed cell metallic foams at high temperature. The foam
specimens with rectangular section were produced from
AlMg1Si0.6TiH20.8 alloy preform material. Bending and free
bending tests based on gravity effect were applied to foam specimens
at high temperatures. During the tests, the time-angular deformation
relationships with various temperatures were determined.
Deformation types formed in cell walls were investigated by means
of Scanning Electron Microscopy (SEM) and optical microscopy.
Bending deformation about 90° was achieved without any defect at
high temperatures. The importance of a critical temperature and
deformation rate was emphasized in maintaining the deformation.
Significant slip lines on surface of cell walls at tensile zones of
bending specimen were observed. At high strain rates, the microcrack
formation in boundaries of elongated grains was determined.
Abstract: Al6061 alloy base matrix, reinforced with particles of
silicon carbide (10 wt %) and Graphite powder (1wt%), known as
hybrid composites have been fabricated by liquid metallurgy route
(stir casting technique) and optimized at different parameters like
applied load, sliding speed and sliding distance by taguchi method. A
plan of experiment generated through taguchi technique was used to
perform experiments based on L27 orthogonal array. The developed
ANOVA and regression equations are used to find the optimum
coefficient of friction and wear under the influence of applied load,
sliding speed and sliding distance. On the basis of “smaller the best”
the dry sliding wear resistance was analysed and finally confirmation
tests were carried out to verify the experimental results.
Abstract: This research paper presents highly optimized barrel
shifter at 22nm Hi K metal gate strained Si technology node. This
barrel shifter is having a unique combination of static and dynamic
body bias which gives lowest power delay product. This power delay
product is compared with the same circuit at same technology node
with static forward biasing at ‘supply/2’ and also with normal reverse
substrate biasing and still found to be the lowest. The power delay
product of this barrel sifter is .39362X10-17J and is lowered by
approximately 78% to reference proposed barrel shifter at 32nm bulk
CMOS technology. Power delay product of barrel shifter at 22nm Hi
K Metal gate technology with normal reverse substrate bias is
2.97186933X10-17J and can be compared with this design’s PDP of
.39362X10-17J. This design uses both static and dynamic substrate
biasing and also has approximately 96% lower power delay product
compared to only forward body biased at half of supply voltage. The
NMOS model used are predictive technology models of Arizona state
university and the simulations to be carried out using HSPICE
simulator.
Abstract: The concentrations of heavy metals in sediments of
Qua Iboe River Estuary (QIRE) were monitored at four different
sampling locations in wet and dry seasons. A preliminary survey to
determine the four sampling stations along the river continuum
showed that the area spanned between
Abstract: Dielectric ceramic samples in the BaO-Re2O3-TiO2
ternary system were synthesized with structural formula Ba2-
xRe4+2x/3Ti8O24 where Re= rare earth metal and Re= Sm and La where
x varies from 0.0 to 0.6 with step size 0.1. Polycrystalline samples
were prepared by the conventional solid state reaction technique. The
dielectric, electrical and impedance analysis of all the samples in the
frequency range 1KHz- 1MHz at room temperature (25°C) have been
done to get the understanding of electrical conduction and dielectric
relaxation and their correlation. Dielectric response of the samples at
lower frequencies shows dielectric dispersion while at higher
frequencies it shows dielectric relaxation. The ac conductivity is well
fitted by the Jonscher law. The spectroscopic data in the impedance
plane confirms the existence of grain contribution to the relaxation.
All the properties are found out to be function of frequency as well as
the amount of substitution.
Abstract: The article presents a plasma chemical technology for
processing solid fuels, using examples of bituminous and brown
coals. Thermodynamic and experimental investigation of the
technology was made. The technology allows producing synthesis
gas from the coal organic mass and valuable components (technical
silicon, ferrosilicon, aluminum, and carbon silicon, as well as
microelements of rare metals, such as uranium, molybdenum,
vanadium, etc.) from the mineral mass. The thusly produced highcalorific
synthesis gas can be used for synthesis of methanol, as a
high-calorific reducing gas instead of blast-furnace coke as well as
power gas for thermal power plants.
Abstract: A field study was conducted to evaluate the efficacy of
safflower plant for phytoremediation of contaminated soils. The
experiment was performed on an agricultural fields contaminated by
the Non-Ferrous-Metal Works near Plovdiv, Bulgaria. Field
experiments with randomized complete block design with five
treatments (control, compost amendments added at 20 and 40 t/daa,
and vermicompost amendments added at 20 and 40 t/daa) were
carried out. The quality of safflower seeds and oil (heavy metals and
fatty acid composition) were determined. Tested organic amendments
significantly influenced the chemical composition of safflower seeds
and oil. The compost and vermicompost treatments significantly
reduced heavy metals concentration in safflower seeds and oils, but
the effect differed among them. Addition of vermicompost and
compost leads to an increase in the content of palmitic acid and
linoleic acid, and a decrease in the stearic and oleic acids compared
with the control. A significant increase in the quantity of saturated
acids was observed in the variants with 20 t/daa of compost and 20
t/daa of vermicompost (9.1 and 8.9% relative to the control).
Safflower is a plant which is tolerant to heavy metals and can be
successfully used in the phytoremediation of heavy metal
contaminated soils. The processing of seeds to oil and using the
obtained oil for nutritional purposes will greatly reduce the cost of
phytoremediation.
Abstract: The secondary alloy A226 is used for many
automotive casting produced by mould casting and high pressure die
casting. This alloy has excellent castability, good mechanical
properties and cost-effectiveness. Production of primary aluminium
alloys belong to heavy source fouling of life environs. The European
Union calls for the emission reduction and reduction in energy
consumption therefore increase production of recycled (secondary)
aluminium cast alloys. The contribution is deal with influence of
recycling on the quality of the casting made from A226 in automotive
industry. The properties of the casting made from secondary
aluminium alloys were compared with the required properties of
primary aluminium alloys. The effect of recycling on microstructure
was observed using combination different analytical techniques (light
microscopy upon black-white etching, scanning electron microscopy
- SEM upon deep etching and energy dispersive X-ray analysis -
EDX). These techniques were used for the identification of the
various structure parameters, which was used to compare secondary
alloy microstructure with primary alloy microstructure.
Abstract: The arsenic and iron environments in different growth
stages have been studied with EXAFS and XANES using
Brookhaven Synchrotron Light Source. Collard Greens plants were
grown and tissue samples were harvested. The project studied the
EXAFS and XANES of tissue samples using As and Fe K-edges. The
Fe absorption and the Fourier transform bond length information
were used as a control comparison. The Fourier transform of the
XAFS data revealed the coexistence of As (III) and As (V) in the As
bonding environment inside the studied plant tissue samples,
although the soil only had As (III). The data suggests that Collard
Greens has a novel pathway to handle arsenic absorption in soil.