Abstract: Natural fibers are used in polymer composites to
improve mechanical properties to replace inorganic reinforcing
agents produced by non-renewable resources. The present study
investigates the tensile and flexural behaviors of palm fibers-high
density polyethylene (HDPE) composite as a function of volume
fraction. The surface of the fibers was treated by mercerization
treatments to improve the wetting behavior of the apolar HDPE. The
treatment characterization was obtained by scanning electron
microscopy, X-Ray diffraction and infrared spectroscopy. Results
evidences that a good adhesion interfacial between fibers-matrix
caused an increase strength and modulus flexural as well as tensile
strength in the modified fibers/HDPE composites when compared to
the pure HDPE and untreated fibers reinforced composites.
Abstract: Biomass treatment through densification is very suitable and helpful technology before its effective energy recovery. Densification process of biomass is significantly influenced by various technological and material variables, which are ultimately reflected on the final solid biofuels quality. The paper deals with the experimental research of the relationship between technological and material variables during densification of fast-growing trees, roundly fast-growing willows. The main goal of presented experimental research is to determine the relationship between compression pressure and raw material particle size from a final briquettes density point of view. Experimental research was realized by single-axis densification. The impact of particle size with interaction of compression pressure and stabilization time on the quality properties of briquettes was determined. These variables interaction affects the final solid biofuels (briquettes) quality. From briquettes production point of view and from densification machines constructions point of view is very important to know about mutual interaction of these variables on final briquettes quality. The experimental findings presented here are showing the importance of mentioned variables during the densification process.
Abstract: One of the major problems being faced by human society is that the global temperature is believed to be rising due to human activity that releases carbon IV Oxide (CO2) to the atmosphere. Carbon IV Oxide is the most important greenhouse gas influencing global warming and possible climate change. With climate change becoming alarming, reducing CO2 in our atmosphere has become a primary goal of international efforts. Forest lands are major sink and could absorb large quantities of carbon if the trees are judiciously managed. The study aims at estimating the carbon sequestration capacity of Pinus caribaea (pine) and Tectona grandis (Teak) under the prevailing environmental conditions and exploring tree growth variables that influences the carbon sequestration capacity in Omo Forest Reserve, Ogun State, Nigeria. Improving forest management by manipulating growth characteristics that influences carbon sequestration could be an adaptive strategy of forestry to climate change. Random sampling was used to select Temporary Sample Plots (TSPs) in the study area from where complete enumeration of growth variables was carried out within the plots. The data collected were subjected to descriptive and correlational analyses. The results showed that average carbon stored by Pine and Teak are 994.4±188.3 Kg and 1350.7±180.6 Kg respectively. The difference in carbon stored in the species is significant enough to consider choice of species relevant in climate change adaptation strategy. Tree growth variables influence the capacity of the tree to sequester carbon. Height, diameter, volume, wood density and age are positively correlated to carbon sequestration. These tree growth variables could be manipulated by the forest manager as an adaptive strategy for climate change while plantations of high wood density species could be relevant for management strategy to increase carbon storage.
Abstract: The purpose of the present work was to develop an innovative food product with good textural and sensorial characteristics. The product, a new type of bread, was prepared with wheat (90%) and lupin (10%) flours, without the addition of any conservatives. Several experiences were also done to find the most appropriate proportion of lupin flour. The optimized product was characterized considering the rheological, physical-chemical and sensorial properties. The water absorption of wheat flour with 10% of lupin was higher than that of the normal wheat flours, and Wheat Ceres flour presented the lower value, with lower dough development time and high stability time. The breads presented low moisture but a considerable water activity. The density of bread decreased with the introduction of lupin flour. The breads were quite white, and during storage the colour parameters decreased. The lupin flour clearly increased the number of alveolus, but the total area increased significantly just for the Wheat Cerealis bread. The addition of lupin flour increased the hardness and chewiness of breads, but the elasticity did not vary significantly. Lupin bread was sensorially similar to wheat bread produced with WCerealis flour, and the main differences are the crust rugosity, colour and alveolus characteristics.
Abstract: The purpose of this study is to identify human walking vertical force by using FFT power spectrum density from the experimental acceleration data of the human body. An experiment on human walking is carried out on a stationary floor especially paying attention to higher components of dynamic vertical walking force. Based on measured acceleration data of the human lumbar part, not only in-phase component with frequency of 2fw, 3fw, but also in-opposite-phase component with frequency of 0.5 fw, 1.5 fw, 2.5 fw where fw is the walking rate is observed. The vertical vibration of pedestrian bridge induced by higher components of human walking vertical force is also discussed in this paper. A full scale measurement for the existing pedestrian bridge with center span length of 33 m is carried out focusing on the resonance phenomenon due to higher components of human walking vertical force. Dynamic response characteristics excited by these vertical higher components of human walking are revealed from the dynamic design viewpoint of pedestrian bridge.
Abstract: The moisture content of densified biomass is a
limiting parameter influencing the quality of this solid biofuel. It
influences its calorific value, density, mechanical strength and
dimensional stability as well as affecting its production process. This
paper deals with experimental research into the effect of moisture
content of the densified material on the final quality of biofuel in the
form of logs (briquettes or pellets). Experiments based on the singleaxis
densification of the spruce sawdust were carried out with a
hydraulic piston press (piston and die), where the densified logs were
produced at room temperature. The effect of moisture content on the
qualitative properties of the logs, including density, change of
moisture, expansion and physical changes, and compressive and
impact resistance were studied. The results show the moisture ranges
required for producing good-quality logs. The experiments were
evaluated and the moisture content of the tested material was
optimized to achieve the optimum value for the best quality of the
solid biofuel. The dense logs also have high-energy content per unit
volume. The research results could be used to develop and optimize
industrial technologies and machinery for biomass densification to
achieve high quality solid biofuel.
Abstract: In some applications, such as image recognition or
compression, segmentation refers to the process of partitioning a
digital image into multiple segments. Image segmentation is typically
used to locate objects and boundaries (lines, curves, etc.) in images.
Image segmentation is to classify or cluster an image into several
parts (regions) according to the feature of image, for example, the
pixel value or the frequency response. More precisely, image
segmentation is the process of assigning a label to every pixel in an
image such that pixels with the same label share certain visual
characteristics. The result of image segmentation is a set of segments
that collectively cover the entire image, or a set of contours extracted
from the image. Several image segmentation algorithms were
proposed to segment an image before recognition or compression. Up
to now, many image segmentation algorithms exist and be
extensively applied in science and daily life. According to their
segmentation method, we can approximately categorize them into
region-based segmentation, data clustering, and edge-base
segmentation. In this paper, we give a study of several popular image
segmentation algorithms that are available.
Abstract: Cole-Cole parameters of 40 post-menopausal women
are compared with their DEXA bone mineral density measurements.
Impedance characteristics of four extremities are compared; left and
right extremities are statistically same, but lower extremities are
statistically different than upper ones due to their different fat
content. The correlation of Cole-Cole impedance parameters to bone
mineral density (BMD) is observed to be higher for dominant arm.
With the post-menopausal population, ANOVA tests of the dominant
arm characteristic frequency, as a predictor for DEXA classified
osteopenic and osteoporic population around lumbar spine, is
statistically very significant. When used for total lumbar spine
osteoporosis diagnosis, the area under the Receiver Operating Curve
of the characteristic frequency is 0.830, suggesting that the Cole-Cole
plot characteristic frequency could be a useful diagnostic parameter
when integrated into standard screening methods for osteoporosis.
Moreover, the characteristic frequency can be directly measured by
monitoring frequency driven angular behavior of the dominant arm
without performing any complex calculation.
Abstract: The fuel potential of six tropical hardwood species
namely: Triplochiton scleroxylon, Ceiba pentandra, Aningeria
robusta, Terminalia superba, Celtis mildbreadii and Piptadenia
africana were studied. Properties studied included species density,
gross calorific value, volatile matter, ash content, organic carbon and
elemental composition. Fuel properties were determined using
standard laboratory methods. The result indicates that the gross
calorific value (GCV) of the species ranged from 20.16 to 22.22
MJ/kg and they slightly varied from each other. Additionally, the
GCV of the biomass materials were higher than that of other biomass
materials like; wheat straw, rice straw, maize straw and sugar cane.
The ash and volatile matter content varied from 0.6075 to 5.0407%,
and 75.23% to 83.70% respectively. The overall rating of the
properties of the six biomass materials suggested that Piptadenia
africana has the best fuel property to be used as briquettes and
Aningeria robusta the worse. This study therefore suggests that a
holistic assessment of a biomass material needs to be done before
selecting it for fuel purpose.
Abstract: In this paper, to model a real life wind turbine, a
probabilistic approach is proposed to model the dynamics of the
blade elements of a small axial wind turbine under extreme stochastic
wind speeds conditions. It was found that the power and the torque
probability density functions even-dough decreases at these extreme
wind speeds but are not infinite. Moreover, we also fund that it
is possible to stabilize the power coefficient (stabilizing the output
power)above rated wind speeds by turning some control parameters.
This method helps to explain the effect of turbulence on the quality
and quantity of the harness power and aerodynamic torque.
Abstract: In this article, a new method is proposed for the measuring of well-being inequality through a model composed of superimposing satisfaction waves. The displacement of households’ satisfactory state (i.e. satisfaction) is defined in a satisfaction string. The duration of the satisfactory state for a given period is measured in order to determine the relationship between utility and total satisfactory time, itself dependent on the density and tension of each satisfaction string. Thus, individual cardinal total satisfaction values are computed by way of a one-dimensional form for scalar sinusoidal (harmonic) moving wave function, using satisfaction waves with varying amplitudes and frequencies which allow us to measure wellbeing inequality. One advantage to using satisfaction waves is the ability to show that individual utility and consumption amounts would probably not commute; hence, it is impossible to measure or to know simultaneously the values of these observables from the dataset. Thus, we crystallize the problem by using a Heisenberg-type uncertainty resolution for self-adjoint economic operators. We propose to eliminate any estimation bias by correlating the standard deviations of selected economic operators; this is achieved by replacing the aforementioned observed uncertainties with households’ perceived uncertainties (i.e. corrected standard deviations) obtained through the logarithmic psychophysical law proposed by Weber and Fechner.
Abstract: In this paper numerical studies have been carried out
to examine the pre-ignition flow features of high-performance solid
propellant rocket motors with two different port geometries but with
same propellant loading density. Numerical computations have been
carried out using a validated 3D, unsteady, 2nd-order implicit, SST k-
ω turbulence model. In the numerical study, a fully implicit finite
volume scheme of the compressible, Reynolds-Averaged, Navier-
Stokes equations is employed. We have observed from the numerical
results that in solid rocket motors with highly loaded propellants
having divergent port geometry the hot igniter gases can create preignition
pressure oscillations leading to thrust oscillations due to the
flow unsteadiness and recirculation. We have also observed that the
igniter temperature fluctuations are diminished rapidly thereby
reaching the steady state value faster in the case of solid propellant
rocket motors with convergent port than the divergent port
irrespective of the igniter total pressure. We have concluded that the
prudent selection of the port geometry, without altering the propellant
loading density, for damping the total temperature fluctuations within
the motor is a meaningful objective for the suppression and control of
instability and/or thrust oscillations often observed in solid propellant
rocket motors with non-uniform port geometry.
Abstract: The nickel-manganese (Ni-Mn) alloy coating prepared
from DC electrodeposition process in sulphamate bath was studied.
The effects of process parameters, such as current density and
electrolyte composition, on the cathodic current efficiency,
microstructure, internal stress and mechanical properties were
investigated. Because of its crucial effect on the application to the
electroforming of microelectronic components, the development of
low internal stress coating with high leveling power was emphasized.
It was found that both the coating’s manganese content and the
cathodic current efficiency increased with the raise in current density.
In addition, the internal stress of the deposited coating showed
compressive nature at low current densities while changed to tensile
one at higher current densities. Moreover, the metallographic
observation, X-ray diffraction measurement, and polarization curve
measurement were conducted. It was found that the Ni-Mn coating
consisted of nano-sized columnar grains and the maximum hardness of
the coating was associated with (111) preferred orientation in the
microstructure. The grain size was refined along with the increase in
the manganese content of the coating, which accordingly, raised its
hardness and resistance to annealing softening. In summary, the
Ni-Mn coating prepared at lower current density of 1-2 A/dm2 had low
internal stress, high leveling power, and better corrosion resistance.
Abstract: The global demand for long-tailed macaques for
medical experimentation has continued to increase. Fulfillment of
Indonesian export demands has been mostly from natural habitats,
based on a harvesting quota. This quota has been determined
according to the total catch for a given year, and not based on
consideration of any demographic parameters or physical
environmental factors with regard to the animal; hence threatening
the sustainability of the various populations. It is therefore necessary
to formulate a method for calculating a sustainable harvesting quota,
based on population parameters in natural habitats. Considering the
possibility of variations in habitat characteristics and population
parameters, a time series observation of demographic and
physical/biotic parameters, in various habitats, was performed on 13
groups of long-tailed macaques, distributed throughout the West
Java, Lampung and Yogyakarta areas of Indonesia. These provinces
were selected for comparison of the influence of human/tourism
activities. Data on population parameters that was collected included
data on life expectancy according to age class, numbers of
individuals by sex and age class, and ‘ratio of infants to reproductive
females’. The estimation of population growth was based on a
population dynamic growth model: the Leslie matrix. The harvesting
quota was calculated as being the difference between the actual
population size and the MVP (minimum viable population) for each
sex and age class. Observation indicated that there were variations within group size
(24–106 individuals), gender (sex) ratio (1:1 to 1:1.3), life expectancy
value (0.30 to 0.93), and ‘ratio of infants to reproductive females’
(0.23 to 1.56). Results of subsequent calculations showed that
sustainable harvesting quotas for each studied group of long-tailed
macaques, ranged from 29 to 110 individuals. An estimation model
of the MVP for each age class was formulated as Log Y = 0.315 +
0.884 Log Ni (number of individual on ith age class). This study also
found that life expectancy for the juvenile age class was affected by
the humidity under tree stands, and dietary plants’ density at sapling,
pole and tree stages (equation: Y=2.296 – 1.535 RH + 0.002 Kpcg –
0.002 Ktg – 0.001 Kphn, R2 = 89.6% with a significance value of
0.001). By contrast, for the sub-adult-adult age class, life expectancy
was significantly affected by slope (equation: Y=0.377 = 0.012 Kml,
R2 = 50.4%, with significance level of 0.007). The infant-toreproductive-
female ratio was affected by humidity under tree stands,
and dietary plant density at sapling and pole stages (equation: Y = -
1.432 + 2.172 RH – 0.004 Kpcg + 0.003 Ktg, R2 = 82.0% with
significance level of 0.001). This research confirmed the importance
of population parameters in determining the minimum viable
population, and that MVP varied according to habitat characteristics
(especially food availability). It would be difficult therefore, to
formulate a general mathematical equation model for determining a
harvesting quota for the species as a whole.
Abstract: Work presented is interested in the characterization of
the quasistatic mechanical properties and in fatigue of a composite
laminated in jute/epoxy. The natural fibers offer promising prospects
thanks to their interesting specific properties, because of their low
density, but also with their bio-deterioration. Several scientific
studies highlighted the good mechanical resistance of the vegetable
fiber composites reinforced, even after several recycling. Because of
the environmental standards that become increasingly severe, one
attends the emergence of eco-materials at the base of natural fibers
such as flax, bamboo, hemp, sisal, jute. The fatigue tests on
elementary vegetable fibers show an increase of about 60% of the
rigidity of elementary fibers of hemp subjected to cyclic loadings. In
this study, the test-tubes manufactured by the method infusion have
sequences of stacking of 0/90° and ± 45° for the shearing and tensile
tests. The quasistatic tests reveal a variability of the mechanical
properties of about 8%. The tensile fatigue tests were carried out for
levels of constraints equivalent to half of the ultimate values of the
composite. Once the fatigue tests carried out for well-defined values
of cycles, a series of static tests of traction type highlights the
influence of the number of cycles on the quasi-static mechanical
behavior of the laminate jute/epoxy.
Abstract: Steel slag is a by-product of the steel industry and can
be used potentially as aggregate in the asphalt mixture. This study
evaluates the use of Steel Slag Aggregates (SSA) as a substitute for
natural aggregates in the production of hot mix asphalt (HMA) for
road construction. Based on intensive laboratory testing program, the
characteristic properties of SSA were assessed to determine its
suitability to be used in HMA. Four different percentages (0, 50, 75,
and 100%) of SSA were used, and the proposed mix designs for
HMA were conducted in accordance with Marshall mix design. The
experiment results revealed that the addition of SSA has a significant
improvement on the properties of HMA. An increase in density and
stability and a reduction in flow and air voids values were clearly
observed in specimens prepared with 100% SSA. It is concluded that
the steel slag can be considered reasonable alternative source of
aggregate for concrete asphalt mixture production.
Abstract: The composite flour blend consisting of corn, pearl
millet, black gram and wheat bran in the ratio of 80:5:10:5 was taken
to prepare the extruded product and their effect on physical properties
of extrudate was studied. The extrusion process was conducted in
laboratory by using twin screw extruder. The physical characteristics
evaluated include lateral expansion, bulk density, water absorption
index, water solubility index, and rehydration ratio and moisture
retention. The Central Composite Rotatable Design (CCRD) was
used to decide the level of processing variables i.e. feed moisture
content (%), screw speed (rpm), and barrel temperature (oC) for the
experiment. The data obtained after extrusion process were analyzed
by using response surface methodology. A second order polynomial
model for the dependent variables was established to fit the
experimental data. The numerical optimization studies resulted in
127°C of barrel temperature, 246 rpm of screw speed, and 14.5% of
feed moisture as optimum variables to produce acceptable extruded
product. The responses predicted by the software for the optimum
process condition resulted in lateral expansion 126%, bulk density
0.28 g/cm3, water absorption index 4.10 g/g, water solubility index
39.90%, rehydration ratio 544% and moisture retention 11.90% with
75% desirability.
Abstract: Coal tar is a liquid by-product of coal pyrolysis
processes. This liquid oil mixture contains various kinds of useful
compounds such as benzoic aromatic compounds and phenolic
compounds. These compounds are widely used as raw material for
insecticides, dyes, medicines, perfumes, coloring matters, and many
others. The coal tar was collected by pyrolysis process of coal
obtained from PT Kaltim Prima Coal and Arutmin-Kalimantan. The
experiments typically occurred at the atmospheric pressure in a
laboratory furnace at temperatures ranging from 300 to 550oC with a
heating rate of 10oC/min and a holding time of 1 hour at the pyrolysis
temperature. The Gas Chromatography-Mass Spectroscopy (GC-MS)
was used to analyze the coal tar components. The obtained coal tar
has the viscosity of 3.12 cp, the density of 2.78 g/cm3, the calorific
value of 11,048.44 cal/g, and the molecular weight of 222.67. The
analysis result showed that the coal tar contained more than 78
chemical compounds such as benzene, cresol, phenol, xylene,
naphtalene, etc. The total phenolic compounds contained in coal tar
are 33.25% (PT KPC) and 17.58% (Arutmin-Kalimantan). The total
naphtalene compounds contained in coal tar is 14.15% (PT KPC) and
17.13% (Arutmin-Kalimantan).
Abstract: A flow column has been innovatively used in the
design of a new electrocoagulation reactor (ECR1) that will reduce
the temperature of water being treated; where the flow columns work
as a radiator for the water being treated. In order to investigate the
performance of ECR1 and compare it to that of traditional reactors;
600 mL water samples with an initial temperature of 350C were
pumped continuously through these reactors for 30 min at current
density of 1 mA/cm2. The temperature of water being treated was
measured at 5 minutes intervals over a 30 minutes period using a
thermometer. Additional experiments were commenced to investigate
the effects of initial temperature (15-350C), water conductivity (0.15
– 1.2 S) and current density (0.5 -3 mA/cm2) on the performance of
ECR1.
The results obtained demonstrated that the ECR1, at a current
density of 1 mA/cm2 and continuous flow model, reduced water
temperature from 350C to the vicinity of 280C during the first 15
minutes and kept the same level till the end of the treatment time.
While, the temperature increased from 28.1 to 29.80C and from 29.8
to 31.90C in the batch and the traditional continuous flow models
respectively. In term of initial temperature, ECR1 maintained the
temperature of water being treated within the range of 22 to 280C
without the need for external cooling system even when the initial
temperatures varied over a wide range (15 to 350C). The influent
water conductivity was found to be a significant variable that affect
the temperature. The desirable value of water conductivity is 0.6 S.
However, it was found that the water temperature increased rapidly
with a higher current density.
Abstract: In the present study, the properties of Al-Al2O3
nanocomposite hollow sphere structures were investigated. For this
reason, the Al-based nanocomposite hollow spheres with different
amounts of nano-alumina reinforcement (0-10wt %) and different
ratio of thickness to diameter (t/D: 0.06-0.3) were prepared via a
powder metallurgy method. Then, the effect of mentioned parameters
was studied on physical and quasi static mechanical properties of
their related prepared structures (open/closed cell) such as density,
hardness, strength, and energy absorption. It was found that, as the
t/D ratio increases the relative density, compressive strength and
energy absorption increase. The highest values of strength and energy
absorption were obtained from the specimen with 5 wt. % of
nanoparticle reinforcement, t/D of 0.3 (t=1 mm, D=400μm) as 22.88
MPa and 13.24 MJ/m3, respectively. The moderate specific strength
of prepared composites in the present study showed the good
consistency with the properties of others low carbon steel composite
with similar structure.