Abstract: In Jordan having deficit atmospheric precipitation, an
increase in water demand occurs during summer months. Jordan can
be regarded with a relatively high potential for wastewater recycling
and reuse. The main purpose of this paper was to investigate the
removal of total suspended solids (TSS) and chemical oxygen
demand (COD) for olive mill wastewater (OMW) by
electrocoagulation (EC) process. In the combination of
electrocoagulation by using coupled iron–aluminum electrodes, the
optimum working pH was found to be around 6. Results indicated
that the electrocoagulation process allowed removal of TSS and COD
of about 82.5% and 47.5%, respectively at 45 mA/cm2 after 70
minutes by using coupled iron–aluminum electrodes. It was
demonstrated that the maximum TSS and COD removals were
obtained at some optimum experimental parameters for current
density, pH, and reaction time.
Abstract: The Al-MoO3-P-CdTe-Al MOS sandwich structures
were fabricated by vacuum deposition method on cleaned glass
substrates. Capacitance versus voltage measurements were performed
at different frequencies and sweep rates of applied voltages for oxide
and semiconductor films of different thicknesses. In the negative
voltage region of the C-V curve a high differential capacitance of the
semiconductor was observed and at high frequencies (
Abstract: The main aim of the presented experiments is to
improve behaviour of sandwich structures under dynamic loading,
such as crash or explosion. This paper describes experimental
investigation on the response of new advanced materials to low and
high velocity load. Blast wave energy absorbers were designed using
two types of porous lightweight raw particle materials based on
expanded glass and ceramics with dimensions of 0.5-1 mm,
combined with polymeric binder. The effect of binder amount on the
static and dynamic properties of designed materials was observed.
Prism shaped specimens were prepared and loaded to obtain physicomechanical
parameters – bulk density, compressive and flexural
strength under quasistatic load, the dynamic response was determined
using Split Hopkinson Pressure bar apparatus. Numerical
investigation of the material behaviour in sandwich structure was
performed using implicit/explicit solver LS-Dyna. As the last step,
the developed material was used as the interlayer of blast resistant
litter bin, and it´s functionality was verified by real field blast tests.
Abstract: Theory of interpretation of electromagnetic fields studied in the electrical prospecting with direct current is mainly developed for the case of a horizontal surface observation. However in practice we often have to work in difficult terrain surface. Conducting interpretation without the influence of topography can cause non-existent anomalies on sections. This raises the problem of studying the impact of different shapes of ground surface relief on the results of electrical prospecting's research. This research examines the numerical solutions of the direct problem of electrical prospecting for two-dimensional and three-dimensional media, taking into account the terrain. The problem is solved using the method of integral equations. The density of secondary currents on the relief surface is obtained.
Abstract: Now in some countries of the world the cellular
market is on the point of saturation, in others - positive dynamics of
development kept on. The reasons for it are also different, but there
are united by their general susceptibility to innovation changes, if
they are really innovative. If to take as an example the cellular market
of Kazakhstan it is defined by the low percent of smart phones at
consumers, the low population density, undercapacity of the 3G
channel, and absence of universal access to the LTE technology that
limits dynamical growth of this branch. These moments are
aggravated by failures of starting commercial projects by private
companies which prevent to be implemented and widely adopted to a
new product among consumers. The object of the research is possible
integration of wireless and program technologies at which
introduction the idea can regenerate in an innovation. The analysis of
existing projects in the market and the possible union of the
technologies through a prism of theoretical bases of innovative
activity shows that efficiency of the company by development and
introduction of innovations is possible only thanks to strict
observance of all terms and conditions of the innovative process
which main term is profit. Despite that fact that on a global scale the
innovativeness issue of companies is very popular, there are no
researches about possibility of innovative breaks in the field of
wireless access to the Internet in the cellular market of Kazakhstan.
Abstract: Thin-walled elements with a matrix set on a base of
high-valuable Portland cement with dispersed reinforcement from
alkali-resistant glass fibres are used in a range of applications as
claddings of buildings and infrastructure constructions as well as
various architectural elements of residential buildings.
Even though their elementary thickness and therefore total weight
is quite low, architects and building companies demand on even
further decreasing of the bulk density of these fibre-cement elements
for the reason of loading elimination of connected superstructures
and easier assembling in demand conditions.
By the means of various kinds of light-weight aggregates it is
possible to achieve light-weighing of these composite elements.
From the range of possible fillers with different material properties
granulated expanded glass worked the best.
By the means of laboratory testing an effect of two fillers based on
expanded glass on the fibre reinforced cement composite was
verified.
Practical applicability was tested in the production of commonly
manufactured glass fibre reinforced concrete elements, such as
channels for electrical cable deposition, products for urban equipment
and especially various cladding elements.
Even though these are not structural elements, it is necessary to
evaluate also strength characteristics and resistance to environment
for their durability in certain applications.
Abstract: This paper presents two techniques, local feature
extraction using image spectrum and low frequency spectrum
modelling using GMM to capture the underlying statistical
information to improve the performance of face recognition
system. Local spectrum features are extracted using overlap sub
block window that are mapped on the face image. For each of this
block, spatial domain is transformed to frequency domain using
DFT. A low frequency coefficient is preserved by discarding high
frequency coefficients by applying rectangular mask on the
spectrum of the facial image. Low frequency information is non-
Gaussian in the feature space and by using combination of several
Gaussian functions that has different statistical properties, the best
feature representation can be modelled using probability density
function. The recognition process is performed using maximum
likelihood value computed using pre-calculated GMM components.
The method is tested using FERET datasets and is able to achieved
92% recognition rates.
Abstract: Today, the pollution due to non-degradable material
such as plastics, has led to studies about the development of
environmental-friendly material. Because of biodegradability
obtained from natural sources, polylactid acid (PLA) and ijuk fiber
are interesting to modify into a composite. This material is also
expected to reduce the impact of environmental pollution. Surface
modification of ijuk fiber through alkalinization with 0.25 M NaOH
solution for 30 minutes was aimed to enhance its compatibility to
PLA, in order to improve properties of the composite such as the
mechanical properties. Alkalinization of the ijuk fibers annihilates
some surface components such as lignin, wax and hemicelloluse, so
the pore on the surface clearly appeared, decreasing of the density
and diameter of the ijuk fibers. The change of the ijuk fiber properties
leads to increase the mechanical properties of PLA composites
reinforced the ijuk fibers through strengthening of the mechanical
interlocking with the PLA matrix. An addition to enhance the
distribution of the fibers in the PLA matrix, the stirring during DCM
solvent evaporation from the mixture of the ijuk fibers and the
dissolved-PLA can reduce amount of the trapped-voids and fibers
pull-out phenomena, which can decrease the mechanical properties of
the composite.
Abstract: Zinc oxide (ZnO) is one of the light emitting materials in ultraviolet (UV) region. In addition, ZnO nanostructures are also attracting increasing research interest as buildingblocks for UV optoelectronic applications. We have succeeded in synthesizing vertically-aligned ZnO nanostructures by laser interference patterning, which is catalyst-free and non-contact technique. In this study, vertically-aligned ZnO nanowall arrays were synthesized using two-beam interference. The maximum height and average thickness of the ZnO nanowalls were about 4.5µm and 200 nm, respectively.UV lasing from a piece of the ZnO nanowall was obtained under the third harmonic of a Q-switched Nd:YAG laser excitation, and the estimated threshold power density for lasing was about 150 kW/cm2. Furthermore, UV lasing from the vertically-aligned ZnO nanowall was also achieved. The results indicate that ZnO nanowalls can be applied to random laser.
Abstract: The turbocharger and turbocharging have been the
inherent component of diesel engines, so that critical parameters of
such engines, as BSFC (Brake Specific Fuel Consumption) or
thermal efficiency, fuel consumption, BMEP (Brake Mean Effective
Pressure), the power density output and emission level have been
improved extensively. In general, the turbocharger can be considered
as the most complex component of diesel engines, because it has
closely interrelated turbomachinery concepts of the turbines and the
compressors to thermodynamic fundamentals of internal combustion
engines and stress analysis of all components.
In this paper, a waste gate for a conventional single stage radial
turbine is investigated by consideration of turbochargers operation
constrains and engine operation conditions, without any detail
designs in the turbine and the compressor. Amount of opening waste
gate which extended between the ranges of full opened and closed
valve, is demonstrated by limiting compressor boost pressure ratio.
Obtaining of an optimum point by regard above mentioned items is
surveyed by three linked meanline modeling programs together
which consist of Turbomatch®, Compal®, Rital® madules in concepts
NREC® respectively.
Abstract: The aim of this study was to build ‘Ubi-Net’, a
decision-making support system for systematic establishment in
U-City planning. We have experienced various urban problems caused
by high-density development and population concentrations in
established urban areas. To address these problems, a U-Service
contributes to the alleviation of urban problems by providing real-time
information to citizens through network connections and related
information. However, technology, devices, and information for
consumers are required for systematic U-Service planning in towns
and cities where there are many difficulties in this regard, and a lack of
reference systems.
Thus, this study suggests methods to support the establishment of
sustainable planning by providing comprehensive information
including IT technology, devices, news, and social networking
services (SNS) to U-City planners through intelligent searches. In this
study, we targeted Smart U-Parking Planning to solve parking
problems in an ‘old’ city. Through this study, we sought to contribute
to supporting advances in U-Space and the alleviation of urban
problems.
Abstract: Sustainability and eco-friendly requirement of
engineering materials are sort for in recent times, thus giving rise to
the development of bio-composites. However, the natural fibres to
matrix interface interactions remain a key issue in getting the desired
mechanical properties from such composites. Treatment of natural
fibres is essential in improving matrix to filler adhesion, hence
improving its mechanical properties. In this study, investigations
were carried out to determine the effect of sodium hydroxide
treatment on the tensile, flexural, impact and hardness properties of
crushed and uncrushed Luffa cylindrica fibre reinforced recycled low
density polyethylene composites. The LC (Luffa cylindrica) fibres
were treated with 0%, 2%, 4%, 6%, 8% and 10% wt. sodium
hydroxide (NaOH) concentrations for a period of 24 hours under
room temperature conditions. A formulation ratio of 80/20 g (matrix
to reinforcement) was maintained for all developed samples. Analysis
of the results showed that the uncrushed luffa fibre samples gave
better mechanical properties compared with the crushed luffa fibre
samples. The uncrushed luffa fibre composites had a maximum
tensile and flexural strength of 7.65 MPa and 17.08 Mpa respectively
corresponding to a young modulus and flexural modulus of 21.08
MPa and 232.22 MPa for the 8% and 4% wt. NaOH concentration
respectively. Results obtained in the research showed that NaOH
treatment with the 8% NaOH concentration improved the mechanical
properties of the LC fibre reinforced composites when compared with
other NaOH treatment concentration values.
Abstract: Composite material based on Fe3Si micro-particles
and Mn-Zn nano-ferrite was prepared using powder metallurgy
technology. The sol-gel followed by autocombustion process was
used for synthesis of Mn0.8Zn0.2Fe2O4 ferrite. 3 wt.% of mechanically
milled ferrite was mixed with Fe3Si powder alloy. Mixed micro-nano
powder system was homogenized by the Resonant Acoustic Mixing
using ResodynLabRAM Mixer. This non-invasive homogenization
technique was used to preserve spherical morphology of Fe3Si
powder particles. Uniaxial cold pressing in the closed die at pressure
600 MPa was applied to obtain a compact sample. Microwave
sintering of green compact was realized at 800°C, 20 minutes, in air.
Density of the powders and composite was measured by
Hepycnometry. Impulse excitation method was used to measure
elastic properties of sintered composite. Mechanical properties were
evaluated by measurement of transverse rupture strength (TRS) and
Vickers hardness (HV). Resistivity was measured by 4 point probe
method. Ferrite phase distribution in volume of the composite was
documented by metallographic analysis.
It has been found that nano-ferrite particle distributed among
micro- particles of Fe3Si powder alloy led to high relative density
(~93%) and suitable mechanical properties (TRS >100 MPa, HV
~1GPa, E-modulus ~140 GPa) of the composite. High electric
resistivity (R~6.7 ohm.cm) of prepared composite indicate their
potential application as soft magnetic material at medium and high
frequencies.
Abstract: Microbial fuel cells (MFCs) represent a promising
technology for simultaneous bioelectricity generation and wastewater
treatment. Catalysts are significant portions of the cost of microbial
fuel cell cathodes. Many materials have been tested as aqueous
cathodes, but air-cathodes are needed to avoid energy demands for
water aeration. The sluggish oxygen reduction reaction (ORR) rate at
air cathode necessitates efficient electrocatalyst such as carbon
supported platinum catalyst (Pt/C) which is very costly. Manganese
oxide (MnO2) was a representative metal oxide which has been
studied as a promising alternative electrocatalyst for ORR and has
been tested in air-cathode MFCs. However the single MnO2 has poor
electric conductivity and low stability. In the present work, the MnO2
catalyst has been modified by doping Pt nanoparticle. The goal of the
work was to improve the performance of the MFC with minimum Pt
loading. MnO2 and Pt nanoparticles were prepared by hydrothermal
and sol gel methods, respectively. Wet impregnation method was
used to synthesize Pt/MnO2 catalyst. The catalysts were further used
as cathode catalysts in air-cathode cubic MFCs, in which anaerobic
sludge was inoculated as biocatalysts and palm oil mill effluent
(POME) was used as the substrate in the anode chamber. The asprepared
Pt/MnO2 was characterized comprehensively through field
emission scanning electron microscope (FESEM), X-Ray diffraction
(XRD), X-ray photoelectron spectroscopy (XPS), and cyclic
voltammetry (CV) where its surface morphology, crystallinity,
oxidation state and electrochemical activity were examined,
respectively. XPS revealed Mn (IV) oxidation state and Pt (0)
nanoparticle metal, indicating the presence of MnO2 and Pt.
Morphology of Pt/MnO2 observed from FESEM shows that the
doping of Pt did not cause change in needle-like shape of MnO2
which provides large contacting surface area. The electrochemical
active area of the Pt/MnO2 catalysts has been increased from 276 to
617 m2/g with the increase in Pt loading from 0.2 to 0.8 wt%. The
CV results in O2 saturated neutral Na2SO4 solution showed that
MnO2 and Pt/MnO2 catalysts could catalyze ORR with different
catalytic activities. MFC with Pt/MnO2 (0.4 wt% Pt) as air cathode
catalyst generates a maximum power density of 165 mW/m3, which
is higher than that of MFC with MnO2 catalyst (95 mW/m3). The
open circuit voltage (OCV) of the MFC operated with MnO2 cathode
gradually decreased during 14 days of operation, whereas the MFC
with Pt/MnO2 cathode remained almost constant throughout the
operation suggesting the higher stability of the Pt/MnO2 catalyst.
Therefore, Pt/MnO2 with 0.4 wt% Pt successfully demonstrated as an
efficient and low cost electrocatalyst for ORR in air cathode MFC with higher electrochemical activity, stability and hence enhanced
performance.
Abstract: Newly synthesized Polypropylene-g-Polyethylene
glycol polymer was first time used for a compartment-less enzymatic
fuel cell. Working electrodes based on Polypropylene-g-Polyethylene
glycol were operated as unmediated and mediated system (with
ferrocene and gold/cobalt oxide nanoparticles). Glucose oxidase and
bilirubin oxidase was selected as anodic and cathodic enzyme,
respectively. Glucose was used as fuel in a single-compartment and
membrane-less cell. Maximum power density was obtained as 0.65
nW cm-2, 65 nW cm-2 and 23500 nW cm-2 from the unmediated,
ferrocene and gold/cobalt oxide modified polymeric film,
respectively. Power density was calculated to be ~16000 nW cm-2 for
undiluted wastewater sample with gold/cobalt oxide nanoparticles
including system.
Abstract: Vehicular Adhoc Network (VANET) is a new
technology which aims to ensure intelligent inter-vehicle
communications, seamless internet connectivity leading to improved
road safety, essential alerts, and access to comfort and entertainment.
VANET operations are hindered by mobile node’s (vehicles)
uncertain mobility. Routing algorithms use metrics to evaluate which
path is best for packets to travel. Metrics like path length (hop count),
delay, reliability, bandwidth, and load determine optimal route. The
proposed scheme exploits link quality, traffic density, and
intersections as routing metrics to determine next hop. This study
enhances Geographical Routing Protocol (GRP) using fuzzy
controllers while rules are optimized with Bee Swarm Optimization
(BSO). Simulations results are compared to conventional GRP.
Abstract: The objective of this study was to identify the optimal
level of partial replacement of Portland cement by the ashes
originating from burning straw and bagasse from sugar cane (ASB).
Order to this end, were made five series of flat plates and cylindrical
bodies: control and others with the partial replacement in 20, 30, 40
and 50% of ASB in relation to the mass of the Ordinary Portland
cement, and conducted a mechanical testing of simple axial
compression (cylindrical bodies) and the four-point bending (flat
plates) and determined water absorption (WA), bulk density (BD)
and apparent void volume (AVV) on both types of specimens. Based
on the data obtained, it may be noted that the control treatment
containing only Portland cement, obtained the best results. However,
the cylindrical bodies with 20% ashes showed better results
compared to the other treatments. And in the formulations plates, the
treatment which showed the best results was 30% cement
replacement by ashes.
Abstract: These days, the field of tissue engineering is getting
serious attention due to its usefulness. Bone tissue engineering helps
to address and sort-out the critical sized and non-healing orthopedic
problems by the creation of manmade bone tissue. We will design
and validate an efficient numerical model, which will simulate the
effective diffusivity in bone tissue engineering. Our numerical model
will be based on the finite element analysis of the diffusion-reaction
equations. It will have the ability to optimize the diffusivity, even
at multi-scale, with the variation of time. It will also have a special
feature “parametric sweep”, with which we will be able to predict
the oxygen, glucose and cell density dynamics, more accurately. We
will fix these problems by modifying the governing equations, by
selecting appropriate spatio-temporal finite element schemes and by
transient analysis.
Abstract: Waste silicon carbide (waste SiC) filled high-density
polyethylene (HDPE) with and without surface modifiers were
studied. Two types of surface modifiers namely; high-density
polyethylene-grafted-maleic anhydride (HDPE-g-MA) and 3-aminopropyltriethoxysilane have been used in this study. The
composites were produced using a two roll mill, extruder and shaped
in a hydraulic compression molding machine. The mechanical
properties of polymer composites such as flexural strength and
modulus, impact strength, tensile strength, stiffness and hardness
were investigated over a range of compositions. It was found that,
flexural strength and modulus, tensile modulus and hardness
increased, whereas impact strength and tensile strength decreased
with the increasing in filler contents, compared to the neat HDPE. At
similar filler content, the effect of both surface modifiers increased
flexural modulus, impact strength, tensile strength and stiffness but
reduced the flexural strength. Morphological investigation using
SEM revealed that the improvement in mechanical properties was
due to enhancement of the interfacial adhesion between waste SiC
and HDPE.
Abstract: In this paper, two options of anodic alumina barrier
layer thinning have been demonstrated. The approaches varied with
the duration of the voltage step. It was found that too long step of the
barrier layer thinning process leads to chemical etching of the
nanopores on their top. At the bottoms pores are not fully opened
what is disadvantageous for further applications in nanofabrication.
On the other hand, while the duration of the voltage step is controlled
by the current density (value of the current density cannot exceed
75% of the value recorded during previous voltage step) the pores are
fully opened. However, pores at the bottom obtained with this
procedure have smaller diameter, nevertheless this procedure
provides electric contact between the bare aluminum (substrate) and
electrolyte, what is suitable for template assisted electrodeposition,
one of the most cost-efficient synthesis method in nanotechnology.