Abstract: Microstructural and hardening changes of
Fe-0.2wt.%V alloy and pure Fe irradiated with 100 keV hydrogen ions
at room temperature were investigated. It was found that dislocation
density varies dramatically after irradiation, ranging from dislocation
free to dense areas with tangled and complex dislocation
configuration. As the irradiated Fe-0.2wt.%V samples were annealed
at 773 K, the irradiation-induced dislocation loops disappear, while
many small precipitates with enriched C distribute in the matrix. Some
large precipitates with enriched V were also observed. The hardness of
Fe-0.2wt.%V alloy and pure Fe increases after irradiation, which
ascribes to the formation of dislocation loops in the irradiated
specimens. Compared with pure Fe, the size of the
irradiation-introduced dislocation loops in Fe-0.2wt.%V alloy
decreases and the density increases, the change of the hardness also
decreases.
Abstract: High density electrical prospecting has been widely
used in groundwater investigation, civil engineering and
environmental survey. For efficient inversion, the forward modeling
routine, sensitivity calculation, and inversion algorithm must be
efficient. This paper attempts to provide a brief summary of the past
and ongoing developments of the method. It includes reviews of the
procedures used for data acquisition, processing and inversion of
electrical resistivity data based on compilation of academic literature.
In recent times there had been a significant evolution in field survey
designs and data inversion techniques for the resistivity method. In
general 2-D inversion for resistivity data is carried out using the
linearized least-square method with the local optimization technique
.Multi-electrode and multi-channel systems have made it possible to
conduct large 2-D, 3-D and even 4-D surveys efficiently to resolve
complex geological structures that were not possible with traditional
1-D surveys. 3-D surveys play an increasingly important role in very
complex areas where 2-D models suffer from artifacts due to off-line
structures. Continued developments in computation technology, as
well as fast data inversion techniques and software, have made it
possible to use optimization techniques to obtain model parameters to
a higher accuracy. A brief discussion on the limitations of the
electrical resistivity method has also been presented.
Abstract: In order to produce lead free piezoceramics with
optimum piezoelectric and dielectric properties, KNN modified with
Li+ (as an A site dopant) and Sb5+ (as a B site dopant)
(K0.49Na0.49Li0.02) (Nb0.96Sb0.04) O3 (referred as KNLNS in this paper)
have been synthesized using solid state reaction method and
conventional sintering technique. The ceramics were sintered in the
narrow range of 1050°C-1090°C for 2-3 h to get precise information
about sintering parameters. Detailed study of dependence of
microstructural, dielectric and piezoelectric properties on sintering
conditions was then carried out. The study suggests that the volatility
of the highly hygroscopic KNN ceramics is not only sensitive to
sintering temperatures but also to sintering durations. By merely
reducing the sintering duration for a given sintering temperature we
saw an increase in the density of the samples which was supported by
the increase in dielectric constants of the ceramics. And since density
directly or indirectly affects almost all the associated properties, other
dielectric and piezoelectric properties were also enhanced as we
approached towards the most suitable sintering temperature and
duration combination. The detailed results are reported in this paper.
Abstract: We investigated the structure and electronic properties
of the compound Mg1-xBixO with varying concentrations of 0, ¼, ½,
and ¾ x bismuth in the the cesium chloride (CsCl), zinc-blende
(ZnS), nickel arsenide (NiAs) NaCl (rock-salt) and WZ (wurtzite)
phases. We calculated. The calculations were performed using the
first-principles pseudo-potential method within the framework of spin
density functional theory (DFT).
Abstract: One of the main challenges in using the Discrete
Element Method (DEM) is to specify the correct input parameter
values. In general, the models are sensitive to the input parameter
values and accurate results can only be achieved if the correct values
are specified. For the linear contact model, micro-parameters such as
the particle density, stiffness, coefficient of friction, as well as the
particle size and shape distributions are required. There is a need for
a procedure to accurately calibrate these parameters before any
attempt can be made to accurately model a complete bulk materials
handling system. Since DEM is often used to model applications in
the mining and quarrying industries, a calibration procedure was
developed for materials that consist of relatively large (up to 40 mm
in size) particles. A coarse crushed aggregate was used as the test
material. Using a specially designed large shear box with a diameter
of 590 mm, the confined Young’s modulus (bulk stiffness) and
internal friction angle of the material were measured by means of the
confined compression test and the direct shear test respectively. DEM
models of the experimental setup were developed and the input
parameter values were varied iteratively until a close correlation
between the experimental and numerical results was achieved. The
calibration process was validated by modelling the pull-out of an
anchor from a bed of material. The model results compared well with
experimental measurement.
Abstract: In the present work, Electrochemical Impedance
Spectrocopy (EIS) is applied to study the transport of different metal
cations through a cation-exchange membrane. This technique enables
the identification of the ionic-transport characteristics and to
distinguish between different transport mechanisms occurring at
different current density ranges. The impedance spectra are
dependent on the applied dc current density, on the type of cation and
on the concentration.
When the applied dc current density increases, the diameter of the
impedance spectra loops increases because all the components of
membrane system resistance increase. The diameter of the impedance
plots decreases in the order of Na(I), Ni(II) and Cr(III) due to the
increased interactions between the negatively charged sulfonic
groups of the membrane and the cations with greater charge. Nyquist
plots are shifted towards lower values of the real impedance, and its
diameter decreases with the increase of concentration due to the
decrease of the solution resistance.
Abstract: PhilSHORE is a multi-site, multi-device and multicriteria
decision support tool designed to support the development of
tidal current energy in the Philippines. Its platform is based on
Geographic Information Systems (GIS) which allows for the
collection, storage, processing, analyses and display of geospatial
data. Combining GIS tools with open source web development
applications, PhilSHORE becomes a webGIS-based marine spatial
planning tool. To date, PhilSHORE displays output maps and graphs
of power and energy density, site suitability and site-device analysis.
It enables stakeholders and the public easy access to the results of
tidal current energy resource assessments and site suitability
analyses. Results of the initial development show that PhilSHORE is
a promising decision support tool for ORE project developments.
Abstract: Fly ash (FA) thanks to the significant presence of SiO2
and Al2O3 as the main components is a potential raw material for
geopolymers production. Mechanical activation is a method for
improving FA reactivity and also the porosity of final mixture; those
parameters can be analysed through sorption properties. They have
direct impact on the durability of fly ash based geopolymer mortars.
In the paper, effect of FA fineness on sorption properties of
geopolymers based on sodium silicate, as well as relationship
between fly ash fineness and apparent density, compressive and
flexural strength of geopolymers are presented. The best results in the
evaluated area reached the sample H1, which contents the highest
portion of particle under 20μm (100% of GFA). The interdependence
of individual tested properties was confirmed for geopolymer
mixtures corresponding to those in the cement based mixtures: higher
is portion of fine particles < 20μm, higher is strength, density and
lower are sorption properties. The compressive strength as well as
sorption parameters of the geopolymer can be reasonably controlled
by grinding process and also ensured by the higher share of fine
particle (to 20μm) in total mass of the material.
Abstract: The main objective of incorporating natural fibers such as Henequen microfibers (NF) into the High Density Polyethylene (HDPE) polymer matrix is to reduce the cost and to enhance the mechanical as well as other properties. The Henequen microfibers were chopped manually to 5-7mm in length and added into the polymer matrix at the optimized concentration of 8 wt %. In order to facilitate the link between Henequen microfibers (NF) and HDPE matrix, coupling agent such as Glycidoxy (Epoxy) Functional Methoxy Silane (GPTS) at various concentrations from 0.1%, 0.3%, 0.5%, 0.7%, 0.9% and 1% by weight to the total fibers were added. The tensile strength of the composite increased marginally while % elongation at break of the composites decreased with increase in silane loading by wt %. Tensile modulus and stiffness observed increased at 0.9 wt % GPTS loading. Flexural as well as impact strength of the composite decreased with increase in GPTS loading by weight %. Dielectric strength of the composite also found increased marginally up to 0.5wt % silane loading and thereafter remained constant.
Abstract: A cyclostationary Gaussian linearization method is
formulated for investigating the time average response of nonlinear
system under sinusoidal signal and white noise excitation. The
quantitative measure of cyclostationary mean, variance, spectrum of
mean amplitude, and mean power spectral density of noise are
analyzed. The qualitative response behavior of stochastic jump and
bifurcation are investigated. The validity of the present approach in
predicting the quantitative and qualitative statistical responses is
supported by utilizing Monte Carlo simulations. The present analysis
without imposing restrictive analytical conditions can be directly
derived by solving non-linear algebraic equations. The analytical
solution gives reliable quantitative and qualitative prediction of mean
and noise response for the Duffing system subjected to both sinusoidal
signal and white noise excitation.
Abstract: The capability of exploiting the electronic charge and
spin properties simultaneously in a single material has made diluted
magnetic semiconductors (DMS) remarkable in the field of
spintronics. We report the designing of DMS based on zinc-blend
ZnO doped with Cr impurity. The full potential linearized augmented
plane wave plus local orbital FP-L(APW+lo) method in density
functional theory (DFT) has been adapted to carry out these
investigations. For treatment of exchange and correlation energy,
generalized gradient approximations have been used. Introducing Cr
atoms in the matrix of ZnO has induced strong magnetic moment
with ferromagnetic ordering at stable ground state. Cr:ZnO was found
to favor the short range magnetic interaction that
reflect tendency of Cr clustering. The electronic structure of ZnO is
strongly influenced in the presence of Cr impurity atoms where
impurity bands appear in the band gap.
Abstract: This study investigates the suitability of using plastic,
such as polyethylene terephthalate (PET), as a partial replacement of
natural coarse and fine aggregates (for example, brick chips and
natural sand) to produce lightweight concrete for load bearing
structural members. The plastic coarse aggregate (PCA) and plastic
fine aggregate (PFA) were produced from melted polyethylene
terephthalate (PET) bottles. Tests were conducted using three
different water–cement (w/c) ratios, such as 0.42, 0.48, and 0.57,
where PCA and PFA were used as 50% replacement of coarse and
fine aggregate respectively. Fresh and hardened properties of
concrete have been compared for natural aggregate concrete (NAC),
PCA concrete (PCC) and PFA concrete (PFC). The compressive
strength of concrete at 28 days varied with the water–cement ratio for
both the PCC and PFC. Between PCC and PFC, PFA concrete
showed the highest compressive strength (23.7 MPa) at 0.42 w/c ratio
and also the lowest compressive strength (13.7 MPa) at 0.57 w/c
ratio. Significant reduction in concrete density was mostly observed
for PCC samples, ranging between 1977–1924 kg/m³. With the
increase in water–cement ratio PCC achieved higher workability
compare to both NAC and PFC. It was found that both the PCA and
PFA contained concrete achieved the required compressive strength
to be used for structural purpose as partial replacement of the natural
aggregate; but to obtain the desired lower density as lightweight
concrete the PCA is most suited.
Abstract: Microalgae Meyerella planktonica is a potential
biofuel source because it can grow in bulk in either autotrophic or
heterotrophic condition. However, the quantitative growth of this
algal type is still low as it tends to precipitates on the bottom.
Besides, the lipid concentration is still low when grown in
autotrophic condition. In contrast, heterotrophic condition can
enhance the lipid concentration. The combination of autotrophic
condition and agitation treatment was conducted to increase the
density of the culture. On the other hand, a heterotrophic condition
was set up to raise the lipid production. A two-stage experiment
was applied to increase the density at the first step and to increase
the lipid concentration in the next step. The autotrophic condition
resulted higher density but lower lipid concentration compared to
heterotrophic one. The agitation treatment produced higher density
in both autotrophic and heterotrophic conditions. The two-stage
experiment managed to enhance the density during the autotrophic
stage and the lipid concentration during the heterotrophic stage.
The highest yield was performed by using 0.4% v/v glycerol as a
carbon source (2.9±0.016 x 10^6 cells w/w) attained 7 days after the
heterotrophic stage began. The lipid concentration was stable
starting from day 7.
Abstract: Problems insulation of building structures is often
closely connected with the problem of moisture remediation. In the
case of historic buildings or if only part of the redevelopment of
envelope of structures, it is not possible to apply the classical external
thermal insulation composite systems. This application is mostly
effective thermal insulation plasters with high porosity and controlled
capillary properties which assures improvement of thermal properties
construction, its diffusion openness towards the external environment
and suitable treatment capillary properties of preventing the
penetration of liquid moisture and salts thereof toward the outer
surface of the structure.
With respect to the current trend of reducing the energy
consumption of building structures and reduce the production of CO2
is necessary to develop capillary-active materials characterized by
their low density, low thermal conductivity while maintaining good
mechanical properties. The aim of researchers at the Faculty of Civil
Engineering, Brno University of Technology is the development and
study of hygrothermal behaviour of optimal materials for thermal
insulation and rehabilitation of building structures with the possible
use of alternative, less energy demanding binders in comparison with
conventional, frequently used binder, which represents cement.
The paper describes the evaluation of research activities aimed at
the development of thermal insulation and repair materials using
lightweight aggregate and alternative binders such as metakaolin and
finely ground fly ash.
Abstract: Poly bag and mulch films for agricultural field caused
pose environmental problem due to the non-degradable plastics
wastes upon disposal. Thus, a degradable poly bag was designed with
hybrid sago starch (SS) and polyvinyl alcohol (PVA). Two Different
blended compositions of SS and PVA hybrid have been compounded.
Then, the hybrids blended are mixed with linear line density
polyethylene (LLDPE) resin to fabricate poly bag film through
conventional film blowing process. Samples of LLDPE, SS and PVA
hybrid film were exposed to UV light and soil burial. The weight
losses were determined during degradation process. Hybrid film by
degradation of starch was found to hydrolyze and hydroxyl groups
decrease on esterification upon exposure to soil burial and uv
radiation. It was found out that, the hybrid film for 60% of SS
composition showed greatest degradation in soil and UV radiation.
Abstract: The objective of this work is to study the effect of two
key factors - external magnetic field and applied current density
during template-based electrodeposition of nickel nanowires using an
electrode distance of 20 mm. Morphology, length, crystallite size and
crystallographic characterization of the grown nickel nanowires at an
electrode distance of 20mm are presented. For this electrode distance
of 20 mm, these two key electrodeposition factors when coupled was
found to reduce crystallite size with a higher growth length and
preferred orientation of Ni crystals. These observed changes can be
inferred to be due to coupled interaction forces induced by the
intensity of applied electric field (current density) and external
magnetic field known as magnetohydrodynamic (MHD) effect during
the electrodeposition process.
Abstract: Rice husk and kenaf filled with calcium carbonate
(CaCO3) and high density polyethylene (HDPE) composite were
prepared separately using twin-screw extruder at 50rpm. Different
filler loading up to 30 parts of rice husk particulate and kenaf fiber
were mixed with the fixed 30% amount of CaCO3 mineral filler to
produce rice husk/CaCO3/HDPE and kenaf/CaCO3/HDPE hybrid
composites. In this study, the effects of natural fiber for both rice
husk and kenaf in CaCO3/HDPE composite on physical, mechanical
and morphology properties were investigated. Field Emission
Scanning Microscope (FeSEM) was used to investigate the impact
fracture surfaces of the hybrid composite. The property analyses
showed that water absorption increased with the presence of kenaf
and rice husk fillers. Natural fibers in composite significantly
influence water absorption properties due to natural characters of
fibers which contain cellulose, hemicellulose and lignin structures.
The result showed that 10% of additional natural fibers into hybrid
composite had caused decreased flexural strength, however additional
of high natural fiber (>10%) filler loading has proved to increase its
flexural strength.
Abstract: In this study, a computational fluid dynamics (CFD)
model has been developed for studying the effect of surface
roughness profile on the EHL problem. The cylinders contact
geometry, meshing and calculation of the conservation of mass and
momentum equations are carried out using the commercial software
packages ICEMCFD and ANSYS Fluent. The user defined functions
(UDFs) for density, viscosity and elastic deformation of the cylinders
as the functions of pressure and temperature are defined for the CFD
model. Three different surface roughness profiles are created and
incorporated into the CFD model. It is found that the developed CFD
model can predict the characteristics of fluid flow and heat transfer in
the EHL problem, including the main parameters such as pressure
distribution, minimal film thickness, viscosity, and density changes.
The results obtained show that the pressure profile at the center of the
contact area directly relates to the roughness amplitude. A rough
surface with kurtosis value of more than 3 has greater influence over
the fluctuated shape of pressure distribution than in other cases.
Abstract: Using the first-principles full-potential linearized
augmented plane wave plus local orbital (FP-LAPW+lo) method
based on density functional theory (DFT), we have investigated the
electronic structure and magnetism of full Heusler alloys Co2ZrGe
and Co2NbB. These compounds are predicted to be half-metallic
ferromagnets (HMFs) with a total magnetic moment of 2.000 B per
formula unit, well consistent with the Slater-Pauling rule.
Calculations show that both the alloys have an indirect band gaps, in
the minority-spin channel of density of states (DOS), with values of
0.58 eV and 0.47 eV for Co2ZrGe and Co2NbB, respectively.
Analysis of the DOS and magnetic moments indicates that their
magnetism is mainly related to the d-d hybridization between the Co
and Zr (or Nb) atoms. The half-metallicity is found to be relatively
robust against volume changes. In addition, an atom inside molecule
AIM formalism and an electron localization function ELF were also
adopted to study the bonding properties of these compounds, building
a bridge between their electronic and bonding behavior.
As they have a good crystallographic compatibility with the lattice of
semiconductors used industrially and negative calculated cohesive
energies with considerable absolute values these two alloys could be
promising magnetic materials in the spintronic field.
Abstract: Considering palm oil as non-drying oil owing to its
low iodine value, an attempt was taken to increase the unsaturation in
the fatty acid chains of palm oil for the preparation of alkyds. To
increase the unsaturation in the palm oil, sulphuric acid (SA) and
para-toluene sulphonic acid (PTSA) was used prior to alcoholysis for
the dehydration process. The iodine number of the oil samples was
checked for the unsaturation measurement by Wijs method. Alkyd
resin was prepared using the dehydrated palm oil by following
alcoholysis and esterification reaction. To improve the film properties
0.5wt.% multi-wall carbon nano tubes (MWCNTs) were used to
manufacture polymeric film. The properties of the resins were
characterized by various physico-chemical properties such as density,
viscosity, iodine value, saponification value, etc. Structural
elucidation was confirmed by Fourier transform of infrared
spectroscopy and proton nuclear magnetic resonance; surfaces of the
films were examined by field-emission scanning electron microscope.
In addition, pencil hardness and chemical resistivity was also
measured by using standard methods. The effect of enhancement of
the unsaturation in the fatty acid chain found significant and
motivational. The resin prepared with dehydrated palm oil showed
improved properties regarding hardness and chemical resistivity
testing. The incorporation of MWCNTs enhanced the thermal
stability and hardness of the films as well.