Abstract: Mobile Ad Hoc Networks (MANETs) is a collection
of mobile devices forming a communication network without
infrastructure. MANET is vulnerable to security threats due to
network’s limited security, dynamic topology, scalability and the lack
of central management. The Quality of Service (QoS) routing in such
networks is limited by network breakage caused by node mobility or
nodes energy depletions. The impact of node mobility on trust
establishment is considered and its use to propagate trust through a
network is investigated in this paper. This work proposes an
enhanced Associativity Based Routing (ABR) with Fuzzy based
Trust (Fuzzy- ABR) routing protocol for MANET to improve QoS
and to mitigate network attacks.
Abstract: The nickel-manganese (Ni-Mn) alloy coating prepared
from DC electrodeposition process in sulphamate bath was studied.
The effects of process parameters, such as current density and
electrolyte composition, on the cathodic current efficiency,
microstructure, internal stress and mechanical properties were
investigated. Because of its crucial effect on the application to the
electroforming of microelectronic components, the development of
low internal stress coating with high leveling power was emphasized.
It was found that both the coating’s manganese content and the
cathodic current efficiency increased with the raise in current density.
In addition, the internal stress of the deposited coating showed
compressive nature at low current densities while changed to tensile
one at higher current densities. Moreover, the metallographic
observation, X-ray diffraction measurement, and polarization curve
measurement were conducted. It was found that the Ni-Mn coating
consisted of nano-sized columnar grains and the maximum hardness of
the coating was associated with (111) preferred orientation in the
microstructure. The grain size was refined along with the increase in
the manganese content of the coating, which accordingly, raised its
hardness and resistance to annealing softening. In summary, the
Ni-Mn coating prepared at lower current density of 1-2 A/dm2 had low
internal stress, high leveling power, and better corrosion resistance.
Abstract: The objective of this paper is to evaluate the effects of
soil-structure interaction (SSI) on the modal characteristics and on
the dynamic response of current structures. The objective is on the
overall behaviour of a real structure of five storeys reinforced
concrete (R/C) building typically encountered in Algeria. Sensitivity
studies are undertaken in order to study the effects of frequency
content of the input motion, frequency of the soil-structure system,
rigidity and depth of the soil layer on the dynamic response of such
structures. This investigation indicated that the rigidity of the soil
layer is the predominant factor in soil-structure interaction and its
increases would definitely reduce the deformation in the R/C
structure. On the other hand, increasing the period of the underlying
soil will cause an increase in the lateral displacements at story levels
and create irregularity in the distribution of story shears. Possible
resonance between the frequency content of the input motion and soil
could also play an important role in increasing the structural
response.
Abstract: In addition to the advantages of light weight, resistant
corrosion and ease of processing, aluminum is also applied to the
long-span spatial structures. However, the elastic modulus of
aluminum is lower than that of the steel. This paper combines the
high performance aluminum honeycomb panel with the aluminum
latticed shell, forming a new panel-and-rod composite shell structure.
Through comparative analysis between the static and dynamic
performance, the conclusion that the structure of composite shell is
noticeably superior to the structure combined before.
Abstract: This paper is concerned with the single-item
continuous review inventory system in which demand is stochastic
and discrete. The budget consumed for purchasing the ordered items
is not restricted but it incurs extra cost when exceeding specific
value. The unit purchasing price depends on the quantity ordered
under the all-units discounts cost structure. In many actual systems,
the budget as a resource which is occupied by the purchased items is
limited and the system is able to confront the resource shortage by
charging more costs. Thus, considering the resource shortage costs as
a part of system costs, especially when the amount of resource
occupied by the purchased item is influenced by quantity discounts,
is well motivated by practical concerns. In this paper, an optimization
problem is formulated for finding the optimal (r, Q) policy, when the
system is influenced by the budget limitation and a discount pricing
simultaneously. Properties of the cost function are investigated and
then an algorithm based on a one-dimensional search procedure is
proposed for finding an optimal (r, Q) policy which minimizes the
expected system costs.
Abstract: In the present study, the properties of Al-Al2O3
nanocomposite hollow sphere structures were investigated. For this
reason, the Al-based nanocomposite hollow spheres with different
amounts of nano-alumina reinforcement (0-10wt %) and different
ratio of thickness to diameter (t/D: 0.06-0.3) were prepared via a
powder metallurgy method. Then, the effect of mentioned parameters
was studied on physical and quasi static mechanical properties of
their related prepared structures (open/closed cell) such as density,
hardness, strength, and energy absorption. It was found that, as the
t/D ratio increases the relative density, compressive strength and
energy absorption increase. The highest values of strength and energy
absorption were obtained from the specimen with 5 wt. % of
nanoparticle reinforcement, t/D of 0.3 (t=1 mm, D=400μm) as 22.88
MPa and 13.24 MJ/m3, respectively. The moderate specific strength
of prepared composites in the present study showed the good
consistency with the properties of others low carbon steel composite
with similar structure.
Abstract: Singular value decomposition based optimisation of
geometric design parameters of a 5-speed gearbox is studied. During
the optimisation, a four-degree-of freedom torsional vibration model
of the pinion gear-wheel gear system is obtained and the minimum
singular value of the transfer matrix is considered as the objective
functions. The computational cost of the associated singular value
problems is quite low for the objective function, because it is only
necessary to compute the largest and smallest singular values (μmax
and μmin) that can be achieved by using selective eigenvalue solvers;
the other singular values are not needed. The design parameters are
optimised under several constraints that include bending stress,
contact stress and constant distance between gear centres. Thus, by
optimising the geometric parameters of the gearbox such as, the
module, number of teeth and face width it is possible to obtain a
light-weight-gearbox structure. It is concluded that the all optimised
geometric design parameters also satisfy all constraints.
Abstract: Workflow scheduling is an important part of cloud
computing and based on different criteria it decides cost, execution
time, and performances. A cloud workflow system is a platform
service facilitating automation of distributed applications based on
new cloud infrastructure. An aspect which differentiates cloud
workflow system from others is market-oriented business model, an
innovation which challenges conventional workflow scheduling
strategies. Time and Cost optimization algorithm for scheduling
Hybrid Clouds (TCHC) algorithm decides which resource should be
chartered from public providers is combined with a new De-De
algorithm considering that every instance of single and multiple
workflows work without deadlocks. To offset this, two new concepts
- De-De Dodging Algorithm and Priority Based Decisive Algorithm -
combine with conventional deadlock avoidance issues by proposing
one algorithm that maximizes active (not just allocated) resource use
and reduces Makespan.
Abstract: Typical load-bearing biological materials like bone,
mineralized tendon and shell, are biocomposites made from both
organic (collagen) and inorganic (biomineral) materials. This
amazing class of materials with intrinsic internally designed
hierarchical structures show superior mechanical properties with
regard to their weak components from which they are formed.
Extensive investigations concentrating on static loading conditions
have been done to study the biological materials failure. However,
most of the damage and failure mechanisms in load-bearing
biological materials will occur whenever their structures are exposed
to dynamic loading conditions. The main question needed to be
answered here is: What is the relation between the layout and
architecture of the load-bearing biological materials and their
dynamic behavior? In this work, a staggered model has been
developed based on the structure of natural materials at nanoscale and
Finite Element Analysis (FEA) has been used to study the dynamic
behavior of the structure of load-bearing biological materials to
answer why the staggered arrangement has been selected by nature to
make the nanocomposite structure of most of the biological materials.
The results showed that the staggered structures will efficiently
attenuate the stress wave rather than the layered structure.
Furthermore, such staggered architecture is effectively in charge of
utilizing the capacity of the biostructure to resist both normal and
shear loads. In this work, the geometrical parameters of the model
like the thickness and aspect ratio of the mineral inclusions selected
from the typical range of the experimentally observed feature sizes
and layout dimensions of the biological materials such as bone and
mineralized tendon. Furthermore, the numerical results validated with
existing theoretical solutions. Findings of the present work emphasize
on the significant effects of dynamic behavior on the natural
evolution of load-bearing biological materials and can help scientists
to design bioinspired materials in the laboratories.
Abstract: DNA Barcode provides good sources of needed
information to classify living species. The classification problem has
to be supported with reliable methods and algorithms. To analyze
species regions or entire genomes, it becomes necessary to use the
similarity sequence methods. A large set of sequences can be
simultaneously compared using Multiple Sequence Alignment which
is known to be NP-complete. However, all the used methods are still
computationally very expensive and require significant computational
infrastructure. Our goal is to build predictive models that are highly
accurate and interpretable. In fact, our method permits to avoid the
complex problem of form and structure in different classes of
organisms. The empirical data and their classification performances
are compared with other methods. Evenly, in this study, we present
our system which is consisted of three phases. The first one, is called
transformation, is composed of three sub steps; Electron-Ion
Interaction Pseudopotential (EIIP) for the codification of DNA
Barcodes, Fourier Transform and Power Spectrum Signal Processing.
Moreover, the second phase step is an approximation; it is
empowered by the use of Multi Library Wavelet Neural Networks
(MLWNN). Finally, the third one, is called the classification of DNA
Barcodes, is realized by applying the algorithm of hierarchical
classification.
Abstract: Processing of Al-19.4Si alloy by high intensive
electron beam has been carried out and multiple increases in fatigue
life of the material have been revealed. Investigations of structure and
surface modified layer destruction of Al-19.4Si alloy subjected to
multicycle fatigue tests to fracture have been carried out by methods
of scanning electron microscopy. The factors responsible for the
increase of fatigue life of Al-19.4Si alloy have been revealed and
analyzed.
Abstract: This study suggests the estimation method of stress
distribution for the beam structures based on TLS (Terrestrial Laser
Scanning). The main components of method are the creation of the
lattices of raw data from TLS to satisfy the suitable condition and
application of CSSI (Cubic Smoothing Spline Interpolation) for
estimating stress distribution. Estimation of stress distribution for the
structural member or the whole structure is one of the important
factors for safety evaluation of the structure. Existing sensors which
include ESG (Electric strain gauge) and LVDT (Linear Variable
Differential Transformer) can be categorized as contact type sensor
which should be installed on the structural members and also there are
various limitations such as the need of separate space where the
network cables are installed and the difficulty of access for sensor
installation in real buildings. To overcome these problems inherent in
the contact type sensors, TLS system of LiDAR (light detection and
ranging), which can measure the displacement of a target in a long
range without the influence of surrounding environment and also get
the whole shape of the structure, has been applied to the field of
structural health monitoring. The important characteristic of TLS
measuring is a formation of point clouds which has many points
including the local coordinate. Point clouds are not linear distribution
but dispersed shape. Thus, to analyze point clouds, the interpolation is
needed vitally. Through formation of averaged lattices and CSSI for
the raw data, the method which can estimate the displacement of
simple beam was developed. Also, the developed method can be
extended to calculate the strain and finally applicable to estimate a
stress distribution of a structural member. To verify the validity of the
method, the loading test on a simple beam was conducted and TLS
measured it. Through a comparison of the estimated stress and
reference stress, the validity of the method is confirmed.
Abstract: It is a major challenge to build a bridge superstructure
that has long-term durability and low maintenance requirements. A
solution to this challenge may be to use new materials or to
implement new structural systems. Fiber Reinforced Polymer (FRP)
composites have continued to play an important role in solving some
of persistent problems in infrastructure applications because of its
high specific strength, light weight, and durability. In this study, the
concept of the hybrid FRP-concrete structural systems is applied to a
bridge superstructure. The hybrid FRP-concrete bridge superstructure
is intended to have durable, structurally sound, and cost effective
hybrid system that will take full advantage of the inherent properties
of both FRP materials and concrete. In this study, two hybrid FRP-concrete
bridge systems were investigated. The first system consists
of trapezoidal cell units forming a bridge superstructure. The second
one is formed by arch cells. The two systems rely on using cellular
components to form the core of the bridge superstructure, and an
outer shell to warp around those cells to form the integral unit of the
bridge. Both systems were investigated analytically by using finite
element (FE) analysis. From the rigorous FE studies, it was
concluded that first system is more efficient than the second.
Abstract: A comparison of activity and stability of the as-formed
Pt/C, Pt-Co and Pt-Pd/C electrocatalysts, prepared by a combined
approach of impregnation and seeding, was performed. According to
the activity test in a single Proton Exchange Membrane (PEM) fuel
cell, the Oxygen Reduction Reaction (ORR) activity of the Pt-M/C
electrocatalyst was slightly lower than that of Pt/C. The j0.9 V and
E10 mA/cm2 of the as-prepared electrocatalysts increased in the order of
Pt/C > Pt-Co/C > Pt-Pd/C. However, in the medium-to-high current
density region, Pt-Pd/C exhibited the best performance. With regard to
their stability in a 0.5 M H2SO4 electrolyte solution, the
electrochemical surface area decreased as the number of rounds of
repetitive potential cycling increased due to the dissolution of the
metals within the catalyst structure. For long-term measurement, Pt-
Pd/C was the most stable than the other three electrocatalysts.
Abstract: Background in music analysis: Traditionally, when we
think about a composer’s sketches, the chances are that we are
thinking in terms of the working out of detail, rather than the
evolution of an overall concept. Since music is a “time art,” it follows
that questions of a form cannot be entirely detached from
considerations of time. One could say that composers tend to regard
time either as a place gradually and partially intuitively filled, or they
can look for a specific strategy to occupy it. It seems that the one
thing that sheds light on Stockhausen’s compositional thinking is his
frequent use of “form schemas,” that is often a single-page
representation of the entire structure of a piece.
Background in music technology: Sonic Visualiser is a program
used to study a musical recording. It is an open source application for
viewing, analyzing, and annotating music audio files. It contains a
number of visualisation tools, which are designed with useful default
parameters for musical analysis. Additionally, the Vamp plugin
format of SV supports to provide analysis such as for example
structural segmentation.
Aims: The aim of paper is to show how SV may be used to obtain
a better understanding of the specific musical work, and how the
compositional strategy does impact on musical structures and musical
surfaces. It is known that “traditional” music analytic methods don’t
allow indicating interrelationships between musical surface (which is
perceived) and underlying musical/acoustical structure.
Main Contribution: Stockhausen had dealt with the most diverse
musical problems by the most varied methods. A characteristic which
he had never ceased to be placed at the center of his thought and
works, it was the quest for a new balance founded upon an acute
connection between speculation and intuition. In the case with
Mikrophonie I (1964) for tam-tam and 6 players Stockhausen makes
a distinction between the “connection scheme,” which indicates the
ground rules underlying all versions, and the form scheme, which is
associated with a particular version. The preface to the published
score includes both the connection scheme, and a single instance of a
“form scheme,” which is what one can hear on the CD recording. In
the current study, the insight into the compositional strategy chosen
by Stockhausen was been compared with auditory image, that is, with
the perceived musical surface. Stockhausen’s musical work is
analyzed both in terms of melodic/voice and timbre evolution.
Implications: The current study shows how musical structures
have determined of musical surface. The general assumption is this,
that while listening to music we can extract basic kinds of musical
information from musical surfaces. It is shown that interactive
strategies of musical structure analysis can offer a very fruitful way
of looking directly into certain structural features of music.
Abstract: Rapid Prototyping (RP) technologies enable physical
parts to be produced from various materials without depending on the
conventional tooling. Fused Deposition Modeling (FDM) is one of
the famous RP processes used at present. Tensile strength and
compressive strength resistance will be identified for different sample
structures and different layer orientations of ABS rapid prototype
solid models. The samples will be fabricated by a FDM rapid
prototyping machine in different layer orientations with variations in
internal geometrical structure. The 0° orientation where layers were
deposited along the length of the samples displayed superior strength
and impact resistance over all the other orientations. The anisotropic
properties were probably caused by weak interlayer bonding and
interlayer porosity.
Abstract: In the years followed independence, an economic
crisis and some conflicts led to the displacement of many people
inside Georgia. The growing poverty, unemployment, low income
and its unequal distribution limited access to basic social service have
had a clear direct impact on Georgian population dynamics and its
age-sex structure. Factors influencing the changing population age
structure and urbanization include mortality, fertility, migration and
expansion of urban. In this paper presents the main factors of
changing the distribution by urban and rural areas. How different are
the urban and rural age and sex structures? Does Georgia have the
same age-sex structure among their urban and rural populations since
1950s?
Abstract: Development of new generation bio-tribological,
multilayer coatings opens an avenue for fabrication of future hightech
functional surfaces. In the presented work, nano-composite,
Cr/CrN+[Cr/ a-C:H implanted by metallic nanocrystals] multilayer
coatings have been developed for surface protection of medical tools.
Thin films were fabricated by a hybrid Pulsed Laser Deposition
technique. Complex microstructure analysis of nanomultilayer
coatings, subjected to mechanical and biological tests, were
performed by means of transmission electron microscopy (TEM).
Microstructure characterization revealed the layered arrangement of
Cr23C6 nanoparticles in multilayer structure. Influence of deposition
conditions on bio-tribological properties of the coatings was studied.
The bio-tests were used as a screening tool for the analyzed
nanomultilayer coatings before they could be deposited on medical
tools. Bio-medical tests were done using fibroblasts. The mechanical
properties of the coatings were investigated by means of a ball-ondisc
mechanical test. The micro hardness was done using Berkovich
indenter. The scratch adhesion test was done using Rockwell
indenter. From the bio-tribological point of view, the optimal
properties had the C106_1 material.
Abstract: This study focuses on a novel method for dispersion
and distribution of reinforcement under high intensive shear stress to
produce metal composites. The polyacrylonitrile (PAN)-based short
carbon fiber (Csf) and Nextel 610 alumina fiber were dispersed under
high intensive shearing at mushy zone in semi-solid of A356 by a
novel method. The bundles and clusters were embedded by
infiltration of slurry into the clusters, thus leading to a uniform
microstructure. The fibers were embedded homogenously into the
aluminum around 576-580°C with around 46% of solid fraction.
Other experiments at 615°C and 568°C which are contained 0% and
90% solid respectively were not successful for dispersion and
infiltration of aluminum into bundles of Csf. The alumina fiber has
been cracked by high shearing load. The morphologies and
crystalline phase were evaluated by SEM and XRD. The adopted
thixo-process effectively improved the adherence and distribution of
Csf into Al that can be developed to produce various composites by
thixomixing.
Abstract: This paper presents an optimization method for
reducing the number of input channels and the complexity of the
feed-forward NARX neural network (NN) without compromising the
accuracy of the NN model. By utilizing the correlation analysis
method, the most significant regressors are selected to form the input
layer of the NN structure. An application of vehicle dynamic model
identification is also presented in this paper to demonstrate the
optimization technique and the optimal input layer structure and the
optimal number of neurons for the neural network is investigated.