Abstract: The performance of multiple tuned mass dampers to
mitigate the seismic vibration of structures considering real time
history data is investigated in this paper. Three different real
earthquake time history data like Kobe, Imperial Valley and
Mammoth Lake are taken in the present study. The multiple tuned
mass dampers (MTMD) are distributed at each storey. For
comparative study, single tuned mass damper (STMD) is installed at
top of the similar structure. This study is conducted for a fixed mass
ratio (5%) and fixed damping ratio (5%) of structures. Numerical
study is performed to evaluate the effectiveness of MTMDs and
overall system performance. The displacement, acceleration, base
shear and storey drift are obtained for both combined system
(structure with MTMD and structure with STMD) for all earthquakes.
The same responses are also obtained for structure without damper
system. From obtained results, it is investigated that the MTMD
configuration is more effective for controlling the seismic response of
the primary system with compare to STMD configuration.
Abstract: During an earthquake, a bridge crane may be
subjected to multiple impacts between crane wheels and rail. In order
to model such phenomena, a time-history dynamic analysis with a
multi-scale approach is performed. The high frequency aspect of the
impacts between wheels and rails is taken into account by a Lagrange
explicit event-capturing algorithm based on a velocity-impulse
formulation to resolve contacts and impacts. An implicit temporal
scheme is used for the rest of the structure. The numerical coupling
between the implicit and the explicit schemes is achieved with a
heterogeneous asynchronous time-integrator.
Abstract: Wireless Sensor Networks (WSNs) have many advantages. Their deployment is easier and faster than wired sensor networks or other wireless networks, as they do not need fixed infrastructure. Nodes are partitioned into many small groups named clusters to aggregate data through network organization. WSN clustering guarantees performance achievement of sensor nodes. Sensor nodes energy consumption is reduced by eliminating redundant energy use and balancing energy sensor nodes use over a network. The aim of such clustering protocols is to prolong network life. Low Energy Adaptive Clustering Hierarchy (LEACH) is a popular protocol in WSN. LEACH is a clustering protocol in which the random rotations of local cluster heads are utilized in order to distribute energy load among all sensor nodes in the network. This paper proposes Connected Dominant Set (CDS) based cluster formation. CDS aggregates data in a promising approach for reducing routing overhead since messages are transmitted only within virtual backbone by means of CDS and also data aggregating lowers the ratio of responding hosts to the hosts existing in virtual backbones. CDS tries to increase networks lifetime considering such parameters as sensors lifetime, remaining and consumption energies in order to have an almost optimal data aggregation within networks. Experimental results proved CDS outperformed LEACH regarding number of cluster formations, average packet loss rate, average end to end delay, life computation, and remaining energy computation.
Abstract: The aim of this study is to evaluate the influence of raw material composition on the microstructure, mechanical and fatigue properties and micromechanisms of failure of nodular cast iron. In order to evaluate the influence of charge composition, the structural analysis, mechanical and fatigue tests and microfractographic analysis were carried out on specimens of ten melts with different charge compositions. The basic charge of individual melts was formed by different ratio of pig iron and steel scrap and by different additive for regulation of chemical composition (silicon carbide or ferrosilicon). The results show differences in mechanical and fatigue properties, which are connected with the microstructure. SiC additive positively influences microstructure. Consequently, mechanical and fatigue properties of nodular cast iron are improved, especially in the melts with higher ratio of steel scrap in the charge.
Abstract: The laws of Newtonian mechanics allow ab-initio
molecular dynamics to model and simulate particle trajectories in
material science by defining a differentiable potential function. This
paper discusses some considerations for the coding of ab-initio
programs for simulation on a standalone computer and illustrates
the approach by C language codes in the context of embedded
metallic atoms in the face-centred cubic structure. The algorithms use
velocity-time integration to determine particle parameter evolution
for up to several thousands of particles in a thermodynamical
ensemble. Such functions are reusable and can be placed in a
redistributable header library file. While there are both commercial
and free packages available, their heuristic nature prevents dissection.
In addition, developing own codes has the obvious advantage of
teaching techniques applicable to new problems.
Abstract: Topology optimization technique utilizes constant
element densities as design parameters. Finally, optimal distribution
contours of the material densities between voids (0) and solids (1) in
design domain represent the determination of topology. It means that
regions with element density values become occupied by solids in
design domain, while there are only void phases in regions where no
density values exist. Therefore the void regions of topology
optimization results provide design information to decide appropriate
depositions of web-opening in structure. Contrary to the basic
objective of the topology optimization technique which is to obtain
optimal topology of structures, this present study proposes a new idea
that topology optimization results can be also utilized for decision of
proper web-opening’s position. Numerical examples of linear
elastostatic structures demonstrate efficiency of methodological
design processes using topology optimization in order to determinate
the proper deposition of web-openings.
Abstract: The purposes of this study are 1) to study the frequent
English writing errors of students registering the course: Reading and
Writing English for Academic Purposes II, and 2) to find out the
results of writing error correction by using coded indirect corrective
feedback and writing error treatments. Samples include 28 2nd year
English Major students, Faculty of Education, Suan Sunandha
Rajabhat University. Tool for experimental study includes the lesson
plan of the course; Reading and Writing English for Academic
Purposes II, and tool for data collection includes 4 writing tests of
short texts. The research findings disclose that frequent English
writing errors found in this course comprise 7 types of grammatical
errors, namely Fragment sentence, Subject-verb agreement, Wrong
form of verb tense, Singular or plural noun endings, Run-ons
sentence, Wrong form of verb pattern and Lack of parallel structure.
Moreover, it is found that the results of writing error correction by
using coded indirect corrective feedback and error treatment reveal
the overall reduction of the frequent English writing errors and the
increase of students’ achievement in the writing of short texts with
the significance at .05.
Abstract: The present work is devoted to thermographic studies of curved composite panels (unidirectional GFRP) with subsurface defects. Various artificial defects, created by inserting PTFE stripe between individual layers of a laminate during manufacturing stage are studied. The analysis is conducted both with the use finite element method and experiments. To simulate transient heat transfer in 3D model with embedded various defect sizes, the ANSYS package is used. Pulsed Thermography combined with optical excitation source provides good results for flat surfaces. Composite structures are mostly used in complex components, e.g., pipes, corners and stiffeners. Local decrease of mechanical properties in these regions can have significant influence on strength decrease of the entire structure. Application of active procedures of thermography to defect detection and evaluation in this type of elements seems to be more appropriate that other NDT techniques. Nevertheless, there are various uncertainties connected with correct interpretation of acquired data. In this paper, important factors concerning Infrared Thermography measurements of curved surfaces in the form of cylindrical panels are considered. In addition, temperature effects on the surface resulting from complex geometry and embedded and real defect are also presented.
Abstract: Intrusion Detection Systems are an essential tool for
network security infrastructure. However, IDSs have a serious
problem which is the generating of massive number of alerts, most of
them are false positive ones which can hide true alerts and make the
analyst confused to analyze the right alerts for report the true attacks.
The purpose behind this paper is to present a formalism model to
perform correlation engine by the reduction of false positive alerts
basing on vulnerability contextual information. For that, we propose
a formalism model based on non-monotonic JClassicδє description
logic augmented with a default (δ) and an exception (є) operator that
allows a dynamic inference according to contextual information.
Abstract: Conventional seismic designs of quay walls in ports are mostly based on pseudo-static analysis. A more advanced alternative is the Performance-Based Design (PBD) method, which evaluates permanent deformations and amounts of (repairable) damage under seismic loading. The aim of this study is to investigate the suitability of this method for anchored sheet pile quay walls that were not purposely designed for seismic loads. A research methodology is developed in which pseudo-static, permanent-displacement and finite element analysis are employed, calibrated with an experimental reference case that considers a typical anchored sheet pile wall. A reduction factor that accounts for deformation behaviour is determined for pseudo-static analysis. A model to apply traditional permanent displacement analysis on anchored sheet pile walls is proposed. Dynamic analysis is successfully carried out. From the research it is concluded that PBD evaluation can effectively be used for seismic analysis and design of this type of structure.
Abstract: This paper describes a method for AWGN (Additive White Gaussian Noise) variance estimation in noisy stochastic signals, referred to as Multiplicative-Noising Variance Estimation (MNVE). The aim was to develop an estimation algorithm with minimal number of assumptions on the original signal structure. The provided MATLAB simulation and results analysis of the method applied on speech signals showed more accuracy than standardized AR (autoregressive) modeling noise estimation technique. In addition, great performance was observed on very low signal-to-noise ratios, which in general represents the worst case scenario for signal denoising methods. High execution time appears to be the only disadvantage of MNVE. After close examination of all the observed features of the proposed algorithm, it was concluded it is worth of exploring and that with some further adjustments and improvements can be enviably powerful.
Abstract: In this paper, we demonstrated a 1 × 4 silicon photonic cascaded arrayed waveguide grating, which is fabricated on a SOI wafer with a 220 nm top Si layer and a 2µm buried oxide layer. The measured on-chip transmission loss of this cascaded arrayed waveguide grating is ~ 5.6 dB, including the fiber-to-waveguide coupling loss. The adjacent crosstalk is 33.2 dB. Compared to the normal single silicon photonic arrayed waveguide grating with a crosstalk of ~ 12.5 dB, the crosstalk of this device has been dramatically increased.
Abstract: In many practical situations, bubbles are dispersed in a
liquid phase. Understanding these complex bubbly flows is therefore
a key issue for applications such as shell and tube heat exchangers,
mineral flotation and oxidation in water treatment. Although a large
body of work exists for bubbles rising in an unbounded medium,
that of bubbles rising in constricted geometries has received less
attention. The particular case of a bubble sliding underneath an
inclined surface is common to two-phase flow systems. The current
study intends to expand this knowledge by performing experiments
to quantify the streamwise flow structures associated with a single
sliding air bubble under an inclined surface in quiescent water. This
is achieved by means of two-dimensional, two-component particle
image velocimetry (PIV), performed with a continuous wave laser
and high-speed camera. PIV vorticity fields obtained in a plane
perpendicular to the sliding surface show that there is significant bulk
fluid motion away from the surface. The associated momentum of the
bubble means that this wake motion persists for a significant time
before viscous dissipation. The magnitude and direction of the flow
structures in the streamwise measurement plane are found to depend
on the point on its path through which the bubble enters the plane.
This entry point, represented by a phase angle, affects the nature and
strength of the vortical structures. This study reconstructs the vorticity
field in the wake of the bubble, converting the field at different
instances in time to slices of a large-scale wake structure. This is, in
essence, Taylor’s ”frozen turbulence” hypothesis. Applying this to the
vorticity fields provides a pseudo three-dimensional representation
from 2-D data, allowing for a more intuitive understanding of the
bubble wake. This study provides insights into the complex dynamics
of a situation common to many engineering applications, particularly
shell and tube heat exchangers in the nucleate boiling regime.
Abstract: The solid solutions of lanthanum niobates substituted by yttrium, bismuth and tungsten were synthesized. The structure of the solid solutions is either LaNbO4-based monoclinic or BiNbO4-based triclinic. The series where niobium is substituted by tungsten on B site reveals phase-modulated structure. The values of cell parameters decrease with increasing the dopant concentration for all samples except the tungsten series although the latter show higher total conductivity.
Abstract: Optimisation of the physical and mechanical properties of cold rolled thin strips is achieved by controlling the rolling parameters. In this paper, the factors affecting the asymmetrical cold rolling of thin low carbon steel strip have been studied at a speed ratio of 1.1 without lubricant applied. The effect of rolling parameters on the resulting microstructure was also investigated. It was found that under dry condition, work roll shifting and work roll cross angle can improve the strip profile, and the result is more significant with an increase of work roll cross angle rather than that of work roll shifting. However, there was no obvious change in microstructure. In addition, effects of rolling parameters on strip profile and microstructure have also been discussed.
Abstract: In this study, the butt welding of the commercial AZ31 magnesium alloy sheets have been carried out by using Tungsten Inert Gas (TIG) welding process with alternative and pulsed current. Welded samples were examined with regards to hardness and microstructure. Despite some recent developments in welding of magnesium alloys, they have some problems such as porosity, hot cracking, oxide formation and so on. Samples of the welded parts have undergone metallographic and mechanical examination. Porosities and homogeneous micron grain oxides were rarely observed. Orientations of the weld microstructure in terms of heat transfer also were rarely observed and equiaxed grain morphology was dominant grain structure as in the base metal. As results, fusion zone and few locations of the HAZ of the welded samples have shown twin’s grains. Hot cracking was not observed for any samples. Weld bead geometry of the welded samples were evaluated as normal according to welding parameters. In the results, conditions of alternative and pulsed current and the samples were compared to each other with regards to microstructure and hardness.
Abstract: Comparative analysis of robotic vehicles for pipe inspection is presented in this paper. The promising concept of self-propelled intelligent robotic vehicle (SPIRV) based on octahedral dodekapod for inspection and operation in active branched pipelines with variable cross-sections is reasoned. SPIRV is able to move in pipeline, regardless of its spatial orientation. SPIRV can also be used to move along the outside of the pipelines as well as in space between surfaces of annular tubes. Every one of faces of the octahedral dodekapod can clamp/unclamp a thing with a closed loop surface of various forms as well as put pressure on environmental surface of contact. These properties open new possibilities for its applications in SPIRV. We examine design principles of octahedral dodekapod as future intelligent building blocks for various robotic vehicles that can self-move and self-reconfigure.
Abstract: This work studies the effect of thickness on structural
and electrical properties of CuAlS2 thin films grown by two stage
vacuum thermal evaporation technique. CuAlS2 thin films of
thicknesses 50nm, 100nm and 200nm were deposited on suitably
cleaned corning 7059 glass substrate at room temperature (RT). In
the first stage Cu-Al precursors were grown at room temperature by
thermal evaporation and in the second stage Cu-Al precursors were
converted to CuAlS2 thin films by sulfurisation under sulfur
atmosphere at the temperature of 673K. The structural properties of
the films were examined by X-ray diffraction (XRD) technique while
electrical properties of the specimens were studied using four point
probe method. The XRD studies revealed that the films are of
crystalline in nature having tetragonal structure. The variations of the
micro-structural parameters, such as crystallite size (D), dislocation
density ( ), and micro-strain ( ), with film thickness were
investigated. The results showed that the crystallite sizes increase as
the thickness of the film increases. The dislocation density and
micro-strain decreases as the thickness increases. The resistivity ( )
of CuAlS2 film is found to decrease with increase in film thickness,
which is related to the increase of carrier concentration with film
thickness. Thus thicker films exhibit the lowest resistivity and high
carrier concentration, implying these are the most conductive films.
Low electrical resistivity and high carrier concentration are widely
used as the essential components in various optoelectronic devices
such as light-emitting diode and photovoltaic cells.
Abstract: In this paper, a single phase soft switched Zero Voltage Transition and Zero Current Transition (ZVT-ZCT) Power Factor Correction (PFC) boost converter is proposed. In the proposed PFC converter, the main switch turns on with ZVT and turns off with ZCT without any additional voltage or current stresses. Auxiliary switch turns on and off with zero current switching (ZCS). Also, the main diode turns on with zero voltage switching (ZVS) and turns off with ZCS. The proposed converter has features like low cost, simple control and structure. The output current and voltage are controlled by the proposed PFC converter in wide line and load range. The theoretical analysis of converter is clarified and the operating steps are given in detail. The simulation results of converter are obtained for 500 W and 100 kHz. It is observed that the semiconductor devices operate with soft switching (SS) perfectly. So, the switching power losses are minimum. Also, the proposed converter has 0.99 power factor with sinusoidal current shape.
Abstract: In this paper, an improved active snubber cell is proposed on account of soft switching (SS) family of pulse width modulation (PWM) DC-DC converters. The improved snubber cell provides zero-voltage transition (ZVT) turn on and zero-current transition (ZCT) turn off for main switch. The snubber cell decreases EMI noise and operates with SS in a wide range of line and load voltages. Besides, all of the semiconductor devices in the converter operate with SS. There is no additional voltage and current stress on the main devices. Additionally, extra voltage stress does not occur on the auxiliary switch and its current stress is acceptable value. The improved converter has a low cost and simple structure. The theoretical analysis of converter is clarified and the operating states are given in detail. The experimental results of converter are obtained by prototype of 500 W and 100 kHz. It is observed that the experimental results and theoretical analysis of converter are suitable with each other perfectly.