Abstract: This paper aims to scale up Dye-sensitized Solar Cell
(DSSC) production using a commonly available industrial material –
stainless steel - and industrial plasma equipment. A working DSSC
electrode formed by (1) coating titania nanotube (TiO2 NT) film on
304 stainless steel substrate using a plasma spray technique; then, (2)
filling the nano-pores of the TiO2 NT film using a TiF4 sol-gel method.
A DSSC device consists of an anode absorbed photosensitive dye
(N3), a transparent conductive cathode with platinum (Pt)
nano-catalytic particles adhered to its surface, and an electrolytic
solution sealed between the anode and the transparent conductive
cathode. The photo-current conversion efficiency of the DSSC sample
was tested under an AM 1.5 Solar Simulator. The sample has a short
current (Isc) of 0.83 mA cm-2, open voltage (Voc) of 0.81V, filling
factor (FF) of 0.52, and conversion efficiency (η) of 2.18% on a 0.16
cm2 DSSC work-piece.
Abstract: Aluminum salt that is generally presents as a solid
phase in the water purification sludge (WPS) can be dissolved,
recovering a liquid phase, by adding strong acid to the sludge solution.
According to the reaction kinetics, when reactant is in the form of
small particles with a large specific surface area, or when the reaction
temperature is high, the quantity of dissolved aluminum salt or
reaction rate, respectively are high. Therefore, in this investigation,
water purification sludge (WPS) solution was treated with ultrasonic
waves to break down the sludge, and different acids (1 N HCl and 1 N
H2SO4) were used to acidify it. Acid dosages that yielded the solution
pH of less than two were used. The results thus obtained indicate that
the quantity of dissolved aluminum in H2SO4-acidified solution
exceeded that in HCl-acidified solution. Additionally, ultrasonic
treatment increased the rate of dissolution of aluminum and the
amount dissolved. The quantity of aluminum dissolved at 60℃ was 1.5
to 2.0 times higher than that at 25℃.
Abstract: Owing to extensive use of hydrogen in refining or
petrochemical units, it is essential to manage hydrogen network in
order to make the most efficient utilization of hydrogen. On the other
hand, hydrogen is an important byproduct not properly used through
petrochemical complexes and mostly sent to the fuel system. A few
works have been reported in literature to improve hydrogen network
for petrochemical complexes. In this study a comprehensive analysis
is carried out on petrochemical units using a modified automated
targeting technique which is applied to determine the minimum
hydrogen consumption. Having applied the modified targeting
method in two petrochemical cases, the results showed a significant
reduction in required fresh hydrogen.
Abstract: This study was aimed to study the probability about
the production of fiberboard made of durian rind through latex with
phenolic resin as binding agent. The durian rind underwent the
boiling process with NaOH [7], [8] and then the fiber from durian
rind was formed into fiberboard through heat press. This means that
durian rind could be used as replacement for plywood in plywood
industry by using durian fiber as composite material with adhesive
substance. This research would study the probability about the
production of fiberboard made of durian rind through latex with
phenolic resin as binding agent. At first, durian rind was split,
exposed to light, boiled and steamed in order to gain durian fiber.
Then, fiberboard was tested with the density of 600 Kg/m3 and 800
Kg/m3. in order to find a suitable ratio of durian fiber and latex.
Afterwards, mechanical properties were tested according to the
standards of ASTM and JIS A5905-1994. After the suitable ratio was
known, the test results would be compared with medium density
fiberboard (MDF) and other related research studies. According to
the results, fiberboard made of durian rind through latex with
phenolic resin at the density of 800 Kg/m3 at ratio of 1:1, the
moisture was measured to be 5.05% with specific gravity (ASTM D
2395-07a) of 0.81, density (JIS A 5905-1994) of 0.88 g/m3, tensile
strength, hardness (ASTM D2240), flexibility or elongation at break
yielded similar values as the ones by medium density fiberboard
(MDF).
Abstract: This paper reports on the enhanced photoluminescence
(PL) of nanocomposites through the layered structuring of phosphor
and quantum dot (QD). Green phosphor of Sr2SiO4:Eu, red QDs of
CdSe/CdS/CdZnS/ZnS core-multishell, and thermo-curable resin
were used for this study. Two kinds of composite (layered and mixed)
were prepared, and the schemes for optical energy transfer between
QD and phosphor were suggested and investigated based on PL decay
characteristics. It was found that the layered structure is more effective
than the mixed one in the respects of PL intensity, PL decay and
thermal loss. When this layered nanocomposite (QDs on phosphor) is
used to make white light emitting diode (LED), the brightness is
increased by 37 %, and the color rendering index (CRI) value is raised
to 88.4 compared to the mixed case of 80.4.
Abstract: In a pilot plant scale of a fluidized bed reactor, a
reduction reaction of sodium sulfate by natural gas has been
investigated. Natural gas is applied in this study as a reductant. Feed
density, feed mass flow rate, natural gas and air flow rate
(independent parameters)and temperature of bed and CO
concentration in inlet and outlet of reactor (dependent parameters)
were monitored and recorded at steady state. The residence time was
adjusted close to value of traditional reaction [1]. An artificial neural
network (ANN) was established to study dependency of yield and
carbon gradient on operating parameters. Resultant 97% accuracy of
applied ANN is a good prove that natural gas can be used as a
reducing agent. Predicted ANN model for relation between other
sources carbon gradient (accuracy 74%) indicates there is not a
meaningful relation between other sources carbon variation and
reduction process which means carbon in granule does not have
significant effect on the reaction yield.
Abstract: This paper aims to fabricated high quality anodic
aluminum oxide (AAO) film by anodization method. AAO pore size,
pore density, and film thickness can be controlled in 10~500 nm,
108~1011 pore.cm-2, and 1~100 μm. AAO volume and surface area can
be computed based on structural parameters such as thickness, pore
size, pore density, and sample size. Base on the thetorical calculation,
AAO has 100 μm thickness with 15 nm, 60 nm, and 500 nm pore
diameters AAO surface areas are 1225.2 cm2, 3204.4 cm2, and 549.7
cm2, respectively. The large unit surface area which is useful for
adsorption application. When AAO adsorbed pH indictor of
bromphenol blue presented a sensitive pH detection of solution
change. This testing method can further be used for the precise
measurement of biotechnology, convenience measurement of
industrial engineering.
Abstract: The mixing behaviors of dry and wet granular
materials in gas fluidized bed systems were investigated
computationally using the combined Computational Fluid Dynamics
and Discrete Element Method (CFD-DEM). Dry particles were
observed to mix fairly rapidly during the fluidization process due to
vigorous relative motions between particles induced by the flow of
gas. In contrast, due to the presence of strong cohesive forces arising
from capillary liquid bridges between wet particles, the mixing
efficiencies of wet granular materials under similar operating
conditions were observed to be reduced significantly.
Abstract: The aim of this study was to extract sugar from
sugarcane using high electric field pulse (HELP) as a non-thermal cell permeabilization method. The result of this study showed that it
is possible to permeablize sugar cane cells using HELP at very short times (less than 10 sec.) and at room temperature. Increasing the field strength (from 0.5kV/cm to 2kV/cm) and pulse number (1 to 12) led to increasing the permeabilization of sugar cane cells. The energy
consumption during HELP treatment of sugar cane (2.4 kJ/kg) was about 100 times less compared to thermal cell disintegration at 85
Abstract: All around the world pulp and paper industries are the
biggest plant production with the environmental pollution as the
biggest challenge facing the pulp manufacturing operations. The
concern among these industries is to produce a high volume of papers
with the high quality standard and of low cost without affecting the
environment. This result obtained from this bleaching study show
that the activation of peroxide was an effective method of reducing
the total applied charge of chlorine dioxide which is harmful to our
environment and also show that softwood and hardwood Kraft pulps
responded linearly to the peroxide treatments. During the bleaching
process the production plant produce chlorines. Under the trial stages
chloride dioxide has been reduced by 3 kg/ton to reduce the
brightness from 65% ISO to 60% ISO of pulp and the dosing point
returned to the E stage charges by pre-treating Kraft pulps with
hydrogen peroxide. The pulp and paper industry has developed
elemental chlorine free (ECF) and totally chlorine free (TCF)
bleaching, in their quest for being environmental friendly, they have
been looking at ways to turn their ECF process into a TCF process
while still being competitive. This prompted the research to
investigate the capability of the hydrogen peroxide as catalyst to
reduce chloride dioxide.
Abstract: This study describes the preparation of a novel proton
conducting membranes based on bacterial cellulose (BC) modified by
grafting of 2-acrylamido-2-methyl-1 -propanesulfonic acid (AMPS)
through UV-induced graft polymerization. These AMPS-g-BC
membranes have been characterized by various techniques including
FTIR, SEM and TGA, to find their successful grafting of AMPS on
BC, surface morphology and thermal stability, respectively. Physical
properties of AMPS-g-BC membranes have been assessed in terms of
Lamda value( λ ), ion exchange capacity(IEC) and proton
conductivity. The relationship between degree of grafting and AMPS
concentration used for grafting has been determined by weight gain
method. An optimum proton conductivity equal to 2.89x10-2 S cm-1
and IEC value equal to 1.79 mmol g-1 have been obtained when 20
wt% AMPS concentration is used for grafting (i.e. the corresponding
membrane is notated as AMPS20-g-BC).
Abstract: The stab resistance performance of newly developed
fabric composites composed of hexagonal paper honeycombs, filled
with shear thickening fluid (STF), and woven Kevlar® fabric or
UHMPE was investigated in this study. The STF was prepared by
dispersing submicron SiO2 particles into polyethylene glycol (PEG).
Our results indicate that the STF-Kevlar composite possessed lower
penetration depth than that of neat Kevlar. In other words, the
STF-Kevlar composite can attain the same energy level in
stab-resistance test with fewer layers of Kevlar fabrics than that of the
neat Kevlar fabrics. It also indicates that STF can be used for the
fabrication of flexible body armors and can provide improved
protection against stab threats. We found that the stab resistance of the
STF-Kevlar composite increases with the increase of SiO2
concentration in STF. Moreover, the silica particles functionalized
with silane coupling agent can further improve the stab resistance.
Abstract: Characterization and evaluation of the activity of Vespa basalis DPP-IV, which expressed in Spodoptera frugiperda 21 cells. The expression of rDPP-IV was confirmed by SDS–PAGE, Western blot analyses, LC-MS/MS and measurement of its peptidase specificity. One-step purification by Ni-NTA affinity chromatography and the total amount of rDPP-IV recovered was approximately 6.4mg per liter from infected culture medium; an equivalent amount would be produced by 1x109 infected Sf21 insect cells. Through the affinity purification led to highly stable rDPP-IV enzyme was recovered and with significant peptidase activity. The rDPP-IV exhibited classical Michaelis–Menten kinetics, with kcat/Km in the range of 10-500 mM-1×S-1 for the five synthetic substrates and optimum substrate is Ala-Pro-pNA. As expected in inhibition assay, the enzymatic activity of rDPP-IV was significantly reduced by 80 or 60% in the presence of sitagliptin (a DPP-IV inhibitor) or PMSF (a serine protease inhibitor), but was not apparently affected by iodoacetamide (a cysteine protease inhibitor).
Abstract: Polylactic acid-g-polyvinyl acetate (PLLA-g-PVAc)
was used as a compatibilizer for 50/50 starch/PLLA blend. PLLA-g-
PVAc with different mol% of PVAc contents were prepared by
grafting PVAc onto PLLA backbone via free radical polymerization
in solution process. Various conditions such as type and the amount
of initiator, monomer concentration, polymerization time and
temperature were studied. Results showed that the highest mol% of
PVAc grafting (16 mol%) was achieved by conducting graft
copolymerization in toluene at 110°C for 10 h using DCP as an
initiator. Chemical structure of the PVAc grafted PLLA was
confirmed by 1H NMR. Blending of modified starch and PLLA in the
presence compatibilizer with different amounts and mol% PVAc was
acquired using internal mixer at 160°C for 15 min. Effects of PVAc
content and the amount of compatibilizer on mechanical properties of
polymer blend were studied. Results revealed that tensile strength and
tensile modulus of polymer blend with higher PVAc grafting content
compatibilizer showed better properties than that of lower PVAc
grafting content compatibilizer. The amount of compatibilizer was
found optimized in the range of 0.5-1.0 Wt% depending on the mol%
PVAc.
Abstract: The traditional method for essential oil extraction from agarwood (Aquilaria Crassna) is to soak it in water and follow with hydrodistillation. The effect of various agarwood pretreatments: ethanol, acid, alkaline, enzymes, and ultrasound, and the effect of subcritical water extraction(SWE) was studied to compare with the traditional method. The major compositions of agarwood oil from hydrodistillation were aroma compounds as follow: aristol-9-en-8- one (21.53%), selina-3, 7(11)-diene (12.96%), τ-himachalene (9.28%), β-guaiene (5.79%), hexadecanoic acid (4.90%) and guaia- 3,9-diene (4.21%). Whereas agarwood oil from pretreatments with ethanol and ultrasound, and SWE got fatty acid compounds. Extraction of agarwood oil using these pretreatments could improve the agarwood oil yields up to 2 times that of the traditional method. The components of the pretreated sample with diluted acid (H2SO4) at pH 4 gave quite similar results as the traditional method. Therefore, the enhancement of essential oil from agarwood depends on requirement of type of extracted oil that involved extraction methods.
Abstract: The draw solute separation process in Forward
Osmosis desalination was simulated in Aspen Plus chemical process
modeling software, to estimate the energy consumption and compare
it with other desalination processes, mainly the Reverse Osmosis
process which is currently most prevalent. The electrolytic chemistry
for the system was retrieved using the Elec – NRTL property method
in the Aspen Plus database. Electrical equivalent of energy required
in the Forward Osmosis desalination technique was estimated and
compared with the prevalent desalination techniques.
Abstract: Using steelmaking slag as a raw material, aragonite superstructure product had been synthesized via an indirect CO2 mineral sequestration rout. It mainly involved two separate steps, in which the element of calcium is first selectively leached from steelmaking slag by a novel leaching media consisting of organic solvent Tributyl phosphate (TBP), acetic acid, and ultra-purity water, followed by enhanced carbonation in a separate step for aragonite superstructure production as well as efficiency recovery of leaching media. Based on the different leaching medium employed in the steelmaking slag leaching process, two typical products were collected from the enhanced carbonation step. The products were characterized by X-ray powder diffraction (XRD) and scanning electron microscopy (SEM), respectively. It reveals that the needle-like aragonite crystals self-organized into aragonite superstructure particles including aragonite microspheres as well as dumbbell-like spherical particles, can be obtained from the steelmaking slag with the purity over 99%.
Abstract: TiO2/MgO composite films were prepared by coating
the magnesium acetate solution in the pores of mesoporous TiO2
films using a dip coating method. Concentrations of magnesium
acetate solution were varied in a range of 1x10-4 – 1x10-1 M. The
TiO2/MgO composite films were characterized by scanning electron
microscopy (SEM), transmission electron microscropy (TEM),
electrochemical impedance spectroscopy(EIS) , transient voltage
decay and I-V test. The TiO2 films and TiO2/MgO composite films
were immersed in a 0.3 mM N719 dye solution. The Dye-sensitized
solar cells with the TiO2/MgO/N719 structure showed an optimal
concentration of magnesium acetate solution of 1x10-3 M resulting in
the MgO film estimated thickness of 0.0963 nm and giving the
maximum efficiency of 4.85%. The improved efficiency of dyesensitized
solar cell was due to the magnesium oxide film as the wide
band gap coating decays the electron back transfer to the triiodide
electrolyte and reduce charge recombination.
Abstract: Fabrication and efficiency enhancement of non-mercury, high efficiency and green field emission lamps using carbon nano-materials such as carbon nanotubes as cathode field emitters was studied. Phosphor was coated on the ITO glass or metal substrates as the anode. The luminescence efficiency enhancement was carried out by upgrading the uniform of the emitters, improving electron and thermal conductivity of the phosphor and the optimization of the design of different cathode/anode configurations. After evaluation of the aforementioned parameters, the luminescence efficiency of the field emission lamps was raised.
Abstract: The composition, vapour pressure, and heat capacity
of nine biodiesel fuels from different sources were measured. The
vapour pressure of the biodiesel fuels is modeled assuming an ideal
liquid phase of the fatty acid methyl esters constituting the fuel. New
methodologies to calculate the vapour pressure and ideal gas and
liquid heat capacities of the biodiesel fuel constituents are proposed.
Two alternative optimization scenarios are evaluated: 1) vapour
pressure only; 2) vapour pressure constrained with liquid heat
capacity. Without physical constraints, significant errors in liquid
heat capacity predictions were found whereas the constrained
correlation accurately fit both vapour pressure and liquid heat
capacity.