Abstract: Recently, Northeast Asia has become one of the three
largest trade areas, covering approximately 30% of the total trade
volume of the world. However, the distribution facilities are saturated
due to the increase in the transportation volume within the area and
with the European countries. In order to accommodate the increase of
the transportation volume, the transportation networking with the
major countries in Northeast Asia and Europe is absolutely necessary.
The Eurasian Logistics Network will develop into an international
passenger transportation network covering the Northeast Asian region
and an international freight transportation network connecting across
Eurasia Continent. This paper surveys the changes and trend of the
distribution network in the Eurasian Region according to the political,
economic and environmental changes of the region, analyses the
distribution network according to the changes in the transportation
policies of the related countries, and provides the direction of the
development of composite transportation on the basis of the present
conditions of transportation means. The transportation means optimal
for the efficiency of transportation system are suggested to be train
ferries, sea & rail or sea & rail & sea. It is suggested to develop
diversified composite transportation means and routes within the
boundary of international cooperation system.
Abstract: In this paper two models using a functional network
were employed to solving classification problem. Functional networks
are generalized neural networks, which permit the specification of
their initial topology using knowledge about the problem at hand. In
this case, and after analyzing the available data and their relations, we
systematically discuss a numerical analysis method used for
functional network, and apply two functional network models to
solving XOR problem. The XOR problem that cannot be solved with
two-layered neural network can be solved by two-layered functional
network, which reveals a potent computational power of functional
networks, and the performance of the proposed model was validated
using classification problems.
Abstract: This paper proposes the analysis and design of robust
fuzzy control to Stochastic Parametrics Uncertaint Linear systems.
This system type to be controlled is partitioned into several linear
sub-models, in terms of transfer function, forming a convex polytope,
similar to LPV (Linear Parameters Varying) system. Once defined the
linear sub-models of the plant, these are organized into fuzzy Takagi-
Sugeno (TS) structure. From the Parallel Distributed Compensation
(PDC) strategy, a mathematical formulation is defined in the frequency
domain, based on the gain and phase margins specifications,
to obtain robust PI sub-controllers in accordance to the Takagi-
Sugeno fuzzy model of the plant. The main results of the paper are
based on the robust stability conditions with the proposal of one
Axiom and two Theorems.
Abstract: This paper proposes an architecture of dynamically
reconfigurable arithmetic circuit. Dynamic reconfiguration is a
technique to realize required functions by changing hardware
construction during operations. The proposed circuit is based on a
complex number multiply-accumulation circuit which is used
frequently in the field of digital signal processing. In addition, the
proposed circuit performs real number double precision arithmetic
operations. The data formats are single and double precision floating
point number based on IEEE754. The proposed circuit is designed
using VHDL, and verified the correct operation by simulations and
experiments.
Abstract: Westudy a dual-channel supply chain under
decentralized setting in which manufacturer sells to retailer and to
customers directly usingan online channel. A customer chooses the
purchase-channel based on price and service quality. Also, to buy
product from the retail store, the customer incurs a transportation cost
influenced by the fluctuating gasoline cost. Both companies are under
the revenue sharing contract. In this contract the retailer share a
portion of the revenue to the manufacturer while the manufacturer
will charge the lower wholesales price. The numerical result shows
that the effects of gasoline costs, the revenue sharing ratio and the
wholesale price play an important role in determining optimal prices.
The result shows that when the gasoline price fluctuatesthe optimal
on-line priceis relatively stable while the optimal retail price moves
in the opposite direction of the gasoline prices.
Abstract: This paper reports a new and accurate method for load-flow solution of radial distribution networks with minimum data preparation. The node and branch numbering need not to be sequential like other available methods. The proposed method does not need sending-node, receiving-node and branch numbers if these are sequential. The proposed method uses the simple equation to compute the voltage magnitude and has the capability to handle composite load modelling. The proposed method uses the set of nodes of feeder, lateral(s) and sub lateral(s). The effectiveness of the proposed method is compared with other methods using two examples. The detailed load-flow results for different kind of load-modellings are also presented.
Abstract: Revolutions Applications such as telecommunications, hands-free communications, recording, etc. which need at least one microphone, the signal is usually infected by noise and echo. The important application is the speech enhancement, which is done to remove suppressed noises and echoes taken by a microphone, beside preferred speech. Accordingly, the microphone signal has to be cleaned using digital signal processing DSP tools before it is played out, transmitted, or stored. Engineers have so far tried different approaches to improving the speech by get back the desired speech signal from the noisy observations. Especially Mobile communication, so in this paper will do reconstruction of the speech signal, observed in additive background noise, using the Kalman filter technique to estimate the parameters of the Autoregressive Process (AR) in the state space model and the output speech signal obtained by the MATLAB. The accurate estimation by Kalman filter on speech would enhance and reduce the noise then compare and discuss the results between actual values and estimated values which produce the reconstructed signals.
Abstract: This paper was to study the clothes dryer using waste
heat from a split type air conditioner with a capacity of 12,648 btu/h.
The drying chamber had a minimum cross section area with the size
of 0.5 x 1.0 m2. The chamber was constructed by sailcloth and was
inside folded with aluminium foil. Then, it was connected to the
condensing unit of an air conditioner. The experiment was carried out
in two aspects which were the clothes drying with and without
auxiliary fan unit. The results showed that the drying rate of clothes
in the chamber installed with and without auxiliary fan unit were
2.26 and 1.1 kg/h, respectively. In case of the chamber installed with
a auxiliary fan unit, the additional power of 0.011 kWh was
consumed and the drying rate was higher than that of clothes drying
without auxiliary fan unit. Without auxiliary fan unit installation, no
energy was required but there was a portion of hot air leaks away
through the punctured holes at the wall of the drying chamber, hence
the drying rate was dropped below. The drying rate of clothes drying
using waste heat was higher than natural indoor drying and
commercial dryer which their drying rate were 0.17 and 1.9 kg/h,
respectively. It was noted that the COP of the air conditioner did not
change during the operating of clothes drying.
Abstract: Stress-strain curve of inter-tube connected carbon nanotube (CNT) reinforced polymer composite under axial loading generated from molecular dynamics simulation is presented. Comparison of the response to axial mechanical loading between this composite system with composite systems reinforced by long, continuous CNTs (replicated via periodic boundary conditions) and short, discontinuous CNTs has been made. Simulation results showed that the inter-tube connection improved the mechanical properties of short discontinuous CNTs dramatically. Though still weaker than long CNT/polymer composite, more remarkable increase in the stiffness relative to the polymer was observed in the inter-tube connected CNT/polymer composite than in the discontinuous CNT/polymer composite. The manually introduced bridge break process resulted in a stress-strain curve of ductile fracture mode, which is consistent with the experimental result.
Abstract: In this paper, we present a vertical wire NMOS
device fabricated using CMOS compatible processes. The
impact of temperature on various device parameters is
investigated in view of usual increase in surrounding
temperature with device density.
Abstract: Drop-in of R-22 alternatives in refrigeration and air conditioning systems requires a redesign of system components to improve system performance and reliability with the alternative refrigerants. The present paper aims at design adiabatic capillary tubes for R-22 alternatives such as R-417A, R-422D and R-438A. A theoretical model has been developed and validated with the available experimental data from literature for R-22 over a wide range of both operating and geometrical parameters. Predicted lengths of adiabatic capillary tube are compared with the lengths of the capillary tube needed under similar experimental conditions and majority of predictions are found to be within 4.4% of the experimental data. Hence, the model has been applied for R-417A, R- 422D and R-438A and capillary tube selection charts and correlations have been computed. Finally a comparison between the selected refrigerants and R-22 has been introduced and the results showed that R-438A is the closest one to R-22.
Abstract: To increase precision and reliability of automatic control systems, we have to take into account of random factors affecting the control system. Thus, operational matrix technique is used for statistical analysis of first order plus time delay system with uniform random parameter. Examples with deterministic and stochastic disturbance are considered to demonstrate the validity of the method. Comparison with Monte Carlo method is made to show the computational effectiveness of the method.
Abstract: Due to heavy energy constraints in WSNs clustering is
an efficient way to manage the energy in sensors. There are many
methods already proposed in the area of clustering and research is
still going on to make clustering more energy efficient. In our paper
we are proposing a minimum spanning tree based clustering using
divide and conquer approach. The MST based clustering was first
proposed in 1970’s for large databases. Here we are taking divide and
conquer approach and implementing it for wireless sensor networks
with the constraints attached to the sensor networks. This Divide and
conquer approach is implemented in a way that we don’t have to
construct the whole MST before clustering but we just find the edge
which will be the part of the MST to a corresponding graph and
divide the graph in clusters there itself if that edge from the graph can
be removed judging on certain constraints and hence saving lot of
computation.
Abstract: Simultaneous Saccharification and Fermentation (SSF) of sugarcane bagasse by cellulase and Pachysolen tannophilus MTCC *1077 were investigated in the present study. Important process variables for ethanol production form pretreated bagasse were optimized using Response Surface Methodology (RSM) based on central composite design (CCD) experiments. A 23 five level CCD experiments with central and axial points was used to develop a statistical model for the optimization of process variables such as incubation temperature (25–45°) X1, pH (5.0–7.0) X2 and fermentation time (24–120 h) X3. Data obtained from RSM on ethanol production were subjected to the analysis of variance (ANOVA) and analyzed using a second order polynomial equation and contour plots were used to study the interactions among three relevant variables of the fermentation process. The fermentation experiments were carried out using an online monitored modular fermenter 2L capacity. The processing parameters setup for reaching a maximum response for ethanol production was obtained when applying the optimum values for temperature (32°C), pH (5.6) and fermentation time (110 h). Maximum ethanol concentration (3.36 g/l) was obtained from 50 g/l pretreated sugarcane bagasse at the optimized process conditions in aerobic batch fermentation. Kinetic models such as Monod, Modified Logistic model, Modified Logistic incorporated Leudeking – Piret model and Modified Logistic incorporated Modified Leudeking – Piret model have been evaluated and the constants were predicted.
Abstract: This paper presents a numerical approach for the static
and dynamic analysis of hydrodynamic radial journal bearings. In the
first part, the effect of shaft and housing deformability on pressure
distribution within oil film is investigated. An iterative algorithm that
couples Reynolds equation with a plane finite elements (FE)
structural model is solved. Viscosity-to-pressure dependency (Vogel-
Barus equation) is also included. The deformed lubrication gap and
the overall stress state are obtained. Numerical results are presented
with reference to a typical journal bearing configuration at two
different inlet oil temperatures. Obtained results show the great
influence of bearing components structural deformation on oil
pressure distribution, compared with results for ideally rigid
components. In the second part, a numerical approach based on
perturbation method is used to compute stiffness and damping
matrices, which characterize the journal bearing dynamic behavior.
Abstract: In this paper, a study on the applications of the
optimization and regression techniques for optimal calculation of
partial ratios of helical gearboxes with second-step double gear-sets
for minimal cross section dimension is introduced. From the condition
of the moment equilibrium of a mechanic system including three gear
units and their regular resistance condition, models for calculation of
the partial ratios of helical gearboxes with second-step double
gear-sets were given. Especially, by regression analysis, explicit
models for calculation of the partial ratios are introduced. These
models allow determining the partial ratios accurately and simply.
Abstract: The effect of the discontinuity of the rail ends and the
presence of lower modulus insulation material at the gap to the
variations of stresses in the insulated rail joint (IRJ) is presented. A
three-dimensional wheel – rail contact model in the finite element
framework is used for the analysis. It is shown that the maximum stress
occurs in the subsurface of the railhead when the wheel contact occurs
far away from the rail end and migrates to the railhead surface as the
wheel approaches the rail end; under this condition, the interface
between the rail ends and the insulation material has suffered
significantly increased levels of stress concentration. The ratio of the
elastic modulus of the railhead and insulation material is found to alter
the levels of stress concentration. Numerical result indicates that a
higher elastic modulus insulating material can reduce the stress
concentration in the railhead but will generate higher stresses in the
insulation material, leading to earlier failure of the insulation material
Abstract: Generally flow behavior in centrifugal fan is observed
to be in a state of instability with flow separation zones on suction
surface as well as near the front shroud. Overall performance of the
diffusion process in a centrifugal fan could be enhanced by
judiciously introducing the boundary layer suction slots. With easy
accessibility of CFD as an analytical tool, an extensive numerical
whole field analysis of the effect of boundary layer suction slots in
discrete regions of suspected separation points is possible. This paper
attempts to explore the effect of boundary layer suction slots
corresponding to various geometrical locations on the impeller with
converging configurations for the slots. The analysis shows that the
converging suction slots located on the impeller blade about 25%
from the trailing edge, significantly improves the static pressure
recovery across the fan. Also it is found that Slots provided at a
radial distance of about 12% from the leading and trailing edges
marginally improve the static pressure recovery across the fan.
Abstract: Markov games are a generalization of Markov
decision process to a multi-agent setting. Two-player zero-sum
Markov game framework offers an effective platform for designing
robust controllers. This paper presents two novel controller design
algorithms that use ideas from game-theory literature to produce
reliable controllers that are able to maintain performance in presence
of noise and parameter variations. A more widely used approach for
controller design is the H∞ optimal control, which suffers from high
computational demand and at times, may be infeasible. Our approach
generates an optimal control policy for the agent (controller) via a
simple Linear Program enabling the controller to learn about the
unknown environment. The controller is facing an unknown
environment, and in our formulation this environment corresponds to
the behavior rules of the noise modeled as the opponent. Proposed
controller architectures attempt to improve controller reliability by a
gradual mixing of algorithmic approaches drawn from the game
theory literature and the Minimax-Q Markov game solution
approach, in a reinforcement-learning framework. We test the
proposed algorithms on a simulated Inverted Pendulum Swing-up
task and compare its performance against standard Q learning.