Abstract: With a development of Hybrid Electric Vehicle(HEV),
A photovoltaic(PV) generation system is used for charging batteries in many cases. A dc/dc converter using PV power for a battery charger
requires a high efficiency. In this paper, A ZVS boost converter using the renewable energies for HEV charger is proposed. Through the theoretical analysis and experimental result, operation modes and characteristics of the proposed topology are verified.
Abstract: As the mobile Internet has become widespread in
recent years, communication based on mobile networks is increasing.
As a result, security threats have been posed with regard to the
abnormal traffic of mobile networks, but mobile security has been
handled with focus on threats posed by mobile malicious codes, and
researches on security threats to the mobile network itself have not
attracted much attention. In mobile networks, the IP address of the data
packet is a very important factor for billing purposes. If one mobile
terminal use an incorrect IP address that either does not exist or could
be assigned to another mobile terminal, billing policy will cause
problems. We monitor and analyze 3G mobile data networks traffics
for a period of time and finds some abnormal IP packets. In this paper,
we analyze the reason for abnormal IP packets on 3G Mobile Data
Networks. And we also propose an algorithm based on IP address table
that contains addresses currently in use within the mobile data network
to detect abnormal IP packets.
Abstract: Phase transformation temperature is one of the most important parameters for the shape memory alloys (SMAs). The most popular method to determine these phase transformation temperatures is the Differential Scanning Calorimeter (DSC), but due to the limitation of the DSC testing itself, it made it difficult for the finished product which is not in the powder form. A novel method which uses the Universal Testing Machine has been conducted to determine the phase transformation temperatures. The Flexinol wire was applied with force and maintained throughout the experiment and at the same time it was heated up slowly until a temperature of approximately 1000C with direct current. The direct current was then slowly decreased to cool down the temperature of the Flexinol wire. All the phase transformation temperatures for Flexinol wire were obtained. The austenite start at 52.540C and austenite finish at 60.900C, while martensite start at 44.780C and martensite finish at 32.840C.
Abstract: This paper proposes a Wavelength Division
Multiplexing (WDM) technology based Storage Area Network
(SAN) for all type of Disaster recovery operation. It considers
recovery when all paths failure in the network as well as the main
SAN site failure also the all backup sites failure by the effect of
natural disasters such as earthquakes, fires and floods, power outage,
and terrorist attacks, as initially SAN were designed to work within
distance limited environments[2]. Paper also presents a NEW PATH
algorithm when path failure occurs. The simulation result and
analysis is presented for the proposed architecture with performance
consideration.
Abstract: In this paper fatigue crack initiation and propagation in notched plate under constant amplitude loading through tensile residual stress field of 2024 T351 Al-alloy plate were investigated. Residual stress field was generated by plastic deformation using finite element method (FEM) where isotropic hardening in Von Mises model was applied. Simulation of fatigue behavior was made on AFGROW code. It was shown that the fatigue crack initiation and propagation were affected by level of residual stress filed. In this investigation, the presence of tensile residual stresses at notch (hole) reduces considerably the total fatigue life. It was shown that the decreasing in stress reduces the fatigue crack growth rates.
Abstract: In this study three commercial semiconductor devices
were characterized in the laboratory for computed tomography
dosimetry: one photodiode and two phototransistors. It was evaluated
four responses to the irradiation: dose linearity, energy dependence,
angular dependence and loss of sensitivity after X ray exposure. The
results showed that the three devices have proportional response with
the air kerma; the energy dependence displayed for each device
suggests that some calibration factors would be applied for each one;
the angular dependence showed a similar pattern among the three
electronic components. In respect to the fourth parameter analyzed,
one phototransistor has the highest sensitivity however it also showed
the greatest loss of sensitivity with the accumulated dose. The
photodiode was the device with the smaller sensitivity to radiation,
on the other hand, the loss of sensitivity after irradiation is negligible.
Since high accuracy is a desired feature for a dosimeter, the
photodiode can be the most suitable of the three devices for
dosimetry in tomography. The phototransistors can also be used for
CT dosimetry, however it would be necessary a correction factor due
to loss of sensitivity with accumulated dose.
Abstract: The study attempted to identify the dominant
intelligences of athletes by comparing the developmental differences
of multiple intelligences between athletes and non-athletes. The
weekly specialized training hours and years of specialized training
was examined to see how it can predict the dominant intelligence with
the age factor controlled. There were 355 participants in the research
(202 athletes and 153 non-athletes). Collected data were analyzed with
one-way MANOVA and multiple hierarchical regression. The results
suggested the dominant intelligences of athletes were Interpersonal
Intelligence, Bodily-Kinesthetic Intelligence, and Intrapersonal
Intelligence. The weekly specialized training hours and years of
specialized training could effectively predict the Interpersonal
Intelligence, Bodily-Kinesthetic Intelligence, and Intrapersonal
Intelligence of athletes. The author suggested the future studies could
focus on the theory construction of weekly specialized training and
years of specialized training. Also, the studies on using “Bridge
strategy" by the athletes to guide disadvantage intelligences with
dominant intelligences are highly valued.
Abstract: In this paper, an ultrasonic technique is proposed to
predict oil content in a fresh palm fruit. This is accomplished by
measuring the attenuation based on ultrasonic transmission mode.
Several palm fruit samples with known oil content by Soxhlet
extraction (ISO9001:2008) were tested with our ultrasonic
measurement. Amplitude attenuation data results for all palm samples
were collected. The Feedforward Neural Networks (FNNs) are
applied to predict the oil content for the samples. The Root Mean
Square Error (RMSE) and Mean Absolute Error (MAE) of the FNN
model for predicting oil content percentage are 7.6186 and 5.2287
with the correlation coefficient (R) of 0.9193.
Abstract: Noise causes significant sensibility changes on a human. This study investigated the effect of five different noises on electroencephalogram (EEG) and subjective evaluation. Six human subjects were exposed to classic piano, ocean wave, alarm in army, ambulance, mosquito noise and EEG data were collected during the experimental session. Alpha band activity in the mosquito noise was smaller than that in the classic piano. Alpha band activity decreased 43.4 ± 8.2 % in the mosquito noise. On the other hand, Beta band activity in the mosquito noise was greater than that in the classic piano. Beta band activity increased 60.1 ± 10.7 % in the mosquito noise. The advances from this study may aid the product design process with human sensibility engineering. This result may provide useful information in designing a human-oriented product to avoid the stress.
Abstract: The neural stimulation has been gaining much interest in neuromodulation research and clinical trials. For efficiency, there is a need for variable electrical stimulation such as current and voltage stimuli as well as wireless framework. In this regard, we develop the wireless neural stimulator capable of voltage and current stimuli. The system consists of ZigBee which is a wireless communication module and stimulus generator. The stimulus generator with 8-bits resolution enable both mono-polar and bi-polar waveform in voltage (-3.3~3.3V) and current(-330~330µA) stimulus mode which is controllable. The experimental results suggest that the proposed neural stimulator can play a role as an effective approach for neuromodulation.
Abstract: In this paper we present an off line system for the
recognition of the handwritten numeric chains. Our work is divided
in two big parts. The first part is the realization of a recognition
system of the isolated handwritten digits. In this case the study is
based mainly on the evaluation of neural network performances,
trained with the gradient back propagation algorithm. The used
parameters to form the input vector of the neural network are
extracted on the binary images of the digits by several methods: the
distribution sequence, the Barr features and the centred moments of
the different projections and profiles. The second part is the
extension of our system for the reading of the handwritten numeric
chains constituted of a variable number of digits. The vertical
projection is used to segment the numeric chain at isolated digits and
every digit (or segment) will be presented separately to the entry of
the system achieved in the first part (recognition system of the
isolated handwritten digits). The result of the recognition of the
numeric chain will be displayed at the exit of the global system.
Abstract: In this paper, a system level behavioural model for RF
power amplifier, which exhibits memory effects, and based on multibranch
system is proposed. When higher order terms are included,
the memory polynomial model (MPM) exhibits numerical
instabilities. A set of memory orthogonal polynomial model
(OMPM) is introduced to alleviate the numerical instability problem
associated to MPM model. A data scaling and centring algorithm was
applied to improve the power amplifier modeling accuracy.
Simulation results prove that the numerical instability can be greatly
reduced, as well as the model precision improved with nonlinear
model.
Abstract: In this paper, we propose the low-MAC FEC controller for practical implementation of JPEG2000 image transmission using IEEE 802.15.4. The proposed low-MAC FEC controller has very small HW size and spends little computation to estimate channel state. Because of this advantage, it is acceptable to apply IEEE 802.15.4 which has to operate more than 1 year with battery. For the image transmission, we integrate the low-MAC FEC controller and RCPC coder in sensor node of LR-WPAN. The modified sensor node has increase of 3% hardware size than conventional zigbee sensor node.
Abstract: The cables in a nuclear power plant are designed to be
used for about 40 years in safe operation environment. However, the
heat and radiation in the nuclear power plant causes the rapid
performance deterioration of cables in nuclear vessels and heat
exchangers, which requires cable lifetime estimation. The most
accurate method of estimating the cable lifetime is to evaluate the
cables in a laboratory. However, removing cables while the plant is
operating is not allowed because of its safety and cost. In this paper, a
robot system to estimate the cable lifetime in nuclear power plants is
developed and tested. The developed robot system can calculate a
modulus value to estimate the cable lifetime even when the nuclear
power plant is in operation.
Abstract: Network security attacks are the violation of
information security policy that received much attention to the
computational intelligence society in the last decades. Data mining
has become a very useful technique for detecting network intrusions
by extracting useful knowledge from large number of network data
or logs. Naïve Bayesian classifier is one of the most popular data
mining algorithm for classification, which provides an optimal way
to predict the class of an unknown example. It has been tested that
one set of probability derived from data is not good enough to have
good classification rate. In this paper, we proposed a new learning
algorithm for mining network logs to detect network intrusions
through naïve Bayesian classifier, which first clusters the network
logs into several groups based on similarity of logs, and then
calculates the prior and conditional probabilities for each group of
logs. For classifying a new log, the algorithm checks in which cluster
the log belongs and then use that cluster-s probability set to classify
the new log. We tested the performance of our proposed algorithm by
employing KDD99 benchmark network intrusion detection dataset,
and the experimental results proved that it improves detection rates
as well as reduces false positives for different types of network
intrusions.
Abstract: This paper demonstrates a model of an e-Learning
system based on nowadays learning theory and distant education
practice. The relationships in the model are designed to be simple
and functional and do not necessarily represent any particular e-
Learning environments. It is meant to be a generic e-Learning
system model with implications for any distant education course
instructional design. It allows online instructors to move away from
the discrepancy between the courses and body of knowledge. The
interrelationships of four primary sectors that are at the e-Learning
system are presented in this paper. This integrated model includes
[1] pedagogy, [2] technology, [3] teaching, and [4] learning. There
are interactions within each of these sectors depicted by system loop
map.
Abstract: The purpose of study was to design and construction
the semi-automatic sliced ginger machine for reduce production times
in sheet and slice ginger procedure furthermore, reduced amount of
labor of slides and cutting method. Take consider into clean and safety of workers and consumers. The principle of machines, used 1
horsepower motor, rotation speed of sliced blade 967 rpm, the diameter of sliced dish 310 mm, consists of 2 blades for sheet cutting
ginger and the power from motor which transfer to rotate the sliced blade roller, rotation speed 440 rpm. The slice cutter roller was sliced
ginger from sheet ginger to line ginger. The conveyer could
adjustment level of motors, used to the beginning area that sheet
ginger was transference to the roller for sheet and sliced cutting in next process. The cover of sliced cutting had channel for 1 tuber of
ginger. The semi-automatic sliced ginger machine could produced sheet ginger 81.8 kg/h (6.2 times of labor) and line ginger 17.9 kg/h
(2.5 times of labor) compare with, labor work could produced sheet
ginger 13.2 kg/h and line ginger 7.1 kg/h, and when timekeeper, the
total times of semi auto machine 30.86 kg/h and labor 4.6 kg/h, there
for the semi auto machine was 6.7 times of labor. The semiautomatic
sliced ginger machine convenient, easy for use and
maintain, in addition to reduce fatigue of body and seriousness from
works; must be used high skill, and protection accident in slicing
procedure. Beside, machine could used with other vegetables for
example potato, carrot .etc
Abstract: This paper proposes a novel spectrum sensing technique
for the digital video broadcasting-terrestrial (DVB-T) systems, which
utilizes the periodicity of pilot signals in the orthogonal frequency
division multiplexing (OFDM) symbols. The proposed scheme can
overcome the effect of the timing synchronization error by recorrelating
the correlation values in the same sample distances. The
numerical results demonstrate that the detection probability performance
of the proposed scheme outperforms that of the conventional
scheme when there exists a timing synchronization error.
Abstract: Indium-tin oxide films are deposited by low plasma
temperature RF sputtering on highly flexible modification of glycol
polyethyleneterephtalate substrates. The produced layers are
characterized with transparency over 82 % and sheet resistance of
86.9 Ω/square. The film’s conductivity was further improved by
additional UV illumination from light source (365 nm), having power
of 250 W. The influence of the UV exposure dose on the structural
and electro-optical properties of ITO was investigated. It was
established that the optimum time of illumination is 10 minutes and
further UV treatment leads to polymer substrates degradation.
Structural and bonds type analysis show that at longer treatment
carbon atoms release and diffuse into ITO films, which worsen their
electrical behavior. For the optimum UV dose the minimum sheet
resistance was measured to be 19.2 Ω/square, and the maximum
transparency remained almost unchanged – above 82 %.
Abstract: The selection for plantation of a particular type of
mustard plant depending on its productivity (pod yield) at the stage
of maturity. The growth of mustard plant dependent on some
parameters of that plant, these are shoot length, number of leaves,
number of roots and roots length etc. As the plant is growing, some
leaves may be fall down and some new leaves may come, so it can
not gives the idea to develop the relationship with the seeds weight at
mature stage of that plant. It is not possible to find the number of
roots and root length of mustard plant at growing stage that will be
harmful of this plant as roots goes deeper to deeper inside the land.
Only the value of shoot length which increases in course of time can
be measured at different time instances. Weather parameters are
maximum and minimum humidity, rain fall, maximum and minimum
temperature may effect the growth of the plant. The parameters of
pollution, water, soil, distance and crop management may be
dominant factors of growth of plant and its productivity. Considering
all parameters, the growth of the plant is very uncertain, fuzzy
environment can be considered for the prediction of shoot length at
maturity of the plant. Fuzzification plays a greater role for
fuzzification of data, which is based on certain membership
functions. Here an effort has been made to fuzzify the original data
based on gaussian function, triangular function, s-function,
Trapezoidal and L –function. After that all fuzzified data are
defuzzified to get normal form. Finally the error analysis
(calculation of forecasting error and average error) indicates the
membership function appropriate for fuzzification of data and use to
predict the shoot length at maturity. The result is also verified using
residual (Absolute Residual, Maximum of Absolute Residual, Mean
Absolute Residual, Mean of Mean Absolute Residual, Median of
Absolute Residual and Standard Deviation) analysis.